Search Documents

By Klaus Detert, Joseph Ziebs

The progress of primary recrystallization has been studied in alloys of nickel with 0.01, 0.1, and 1.0 at. pct Ta. It can be shown that in one particular alloy containing 0.1 Ta and 0.02 02 a large grain structure (0.5 mm diameter) could he developed by primary recrystallization in thin sheetswhich were cold-worked to 97.5 pct reduction in thickness. Electron transmission microscopy demmstrates that this phenonmena was linked to the occurrence of fine precipitates at subboundaries. A discussion of how fine precipitates can exert under certain circumstances a rather distinct retarding effect on nucleation rate is included. IN a former investigation, the recrystallization and texture formation in a series of binary nickel alloys including pure nickel were studied.' Nickel alloys with some tantalum added displayed peculiarities during primary recrystallization which have been studied in more detail by the present investigation. The alloys were prepared by powder-metallurgy techniques similar to the previous investigations.' Pure metal powders were thoroughly mixed to obtain alloys with 0.01, 0.1, and 1.0 at. pct Ta, referred to as alloy A, B, or C, respectively. The metallic impurities were kept below 0.005 at. pct except iron and cobalt with slightly higher values, by using highly purified nickel and tantalum powders.' The mixtures were pressed into bars and sintered at a temperature of 1300°C. The sintering atmosphere was either high vacuum, dry hydrogen, or wet hydrogen. The sintered rectangular bars were rolled 60 pct to a thickness of 3 mm, then annealed under dry hydrogen at 1000°C and again cold-rolled to about 97.5 pct reduction of thickness. After this heavy deformation, the sheet thickness was 0.07 5 mm. In order to study primary recrystallization which occurred in measurable times between 400" and 600°C, samples of the rolled sheets were annealed in a salt bath at various temperatures for various times in order to study the progress of recrystallization by hardness measurements and microscopic examination. For optical observation, the samples were polished and etched in a solution of 65 cu cm HNO3, and 18 cu cm acetic acid in 20 to 100 cu cm H2O, depending of the particular sample and annealing treatment. For transmission electron microscopic observations, thin foils were prepared by the combined window and Bollmann techniques.273 The electrolyte consisted of 23 pct perchloric acid and 77 pct acetic acid held at 15°C. Polishing was performed at a current density of 0.4 amp per sq cm. The examination of the thin films was accomplished by a Siemens Elmiscope-type electron microscope operating with an accelerating voltage of 100 kv. RESULTS The progress of primary recrystallization was very accurately followed in these alloys in order to establish the time when recrystallization started and ended during an isothermal anneal. Table I gives some of the data obtained by these studies. The time for beginning is a mean value, where somewhat less than 5 pct of the matrix has recrys-tallized. The end of recrystallization is the time when at least 95 pct of the matrix has recrystal-lized. Listed are three different B alloys, with 0.1 Ta distinguished by different sintering atmospheres which influence the rate of primary recrystallization. By the above method, the state of the grain structure when primary recrystallization was completed, but grain coarsening had not started, could be clearly defined. The average grain diameter of the recrystallized matrix is also given in Table I. The grain size did not depend on the temperature of the isothermal anneal. With one exception the grain size of the primary recrystallized matrix was found to be rather fine

Jan 1, 1965

Foreword—H. Foster Bain........................ 7 Officers and Committees......................... 9 PAPERS Growth of Metallic Crystals. By C. H. Desch...............13 Aluminum Castings of High Strength. By R. S. Archer and Zay .Teffries (With Discussion).............................35 Constitution of Alloys of Aluminum, Zinc and Tin and Aluminum, Zinc and Cadmium. By V. Jares.......................65 Exudations on Brass and Bronze. By W. B. Price and A. J. Phillips (With Discussion)..................•..........80 Preparation of Metallic Single Crystals and Twinning in Zinc and Zinc Single Crystals. By 0. E. Romig (With Discussion).............90 Plastic Deformation of a Zinc Single Crystal. By S. L. Hoyt (With Discussion) 116 Plastic Deformation of Coarse-grained Zinc. By C. H. Mathewson and A. J. Phillips (With Discussion)......................143 The Solidus Line in the Lead-antimony System. By E. E. Schumacher and F. C. Nix (With Discussion)........................195 Note on the Distribution of Energy in Worked Metals and the Effect of Process Annealing Temperature on the Final Annealing Temperature of Fine Copper Wire. By L. Zickrick and R. S. Dean (With Discussion)........207 Note on the Relation of Annealing Temperature to Conductivity of Copper Wire. Ry J. C. Bradley (With Discussion)..................210 Beryllium-copper Alloys. By W. H. Bassett (With Discussion)........218 Some Comparative Properties of Tough Pitch and Phosphorized Copper. By W. R. Webster, J. L. Christie and R. S. Pratt (With Discussion).....233 A Study of the 470" C. Transition Point in Cast 60:40 Brass. By Frances Hurd Clark (With Discussion).......................253 Strldy of the Heat Treatment, Microstructure and Hardness of 60:40 Brass. By Frances Hurd Clark (With Discussion)...............276 Corrosion and Physical Properties of Some Alloys of Aluminurn, Zinc and Tin. By N. 0. Taylor (With Discussion)..................302 Equilibrium Relations in Al-Mn Alloys of High Purity. By E. H. Dix, Jr., and W. D. Iieith (With Discussion)....................315 Deformation of an Aluminum Alloy by a Constant Load. By C. B. Sadtler and J. L. Gregg (With Discussion)....................336 Still Casting of Metals. By P. H. G. Durville (With Discussion).......343

Jan 1, 1927

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer's Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors' Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By J. M. Boutwell

PAGE I. Introduction,.......541 II. General Geography,......542 III. General Geology,......544 1. Sedimentary Rocks,..... 544 2. Igneous Rocks,...... 545 3. Areal Geology,.......546 4. Structural Geology......547 IV. General Character of Ore-Deposits,...548 V. Genesis of the Disseminated Ore in Monzonite,.... 549 1. General,........549 2. Character and Occurrence,... 649 3. Genesis,....... 550 4. Superficial Alteration.....553 5. Conclusion......553 VI. Genesis of the Ore in Fissures,...553 1. Character........... 553 2 Occurrence......554 3. Deposition...... 556 4. Transporting Agent....555 6. Immediate Causes of Deposition..556 6. Superficial Alteration....564 7. Conclusionl ..... 565 VII. Genesis of the Copper-Ore in Limestone...... 566 1. Character......566 2. Occurrencel .....566 3. Deposition......567 4. Relation of Fissures.....569 5. Relation of Intrusives,...571 6. Superficial Alteration....575 7. Conclusion......578 VIII. Periods of Ore-Deposition....578 IX. Dates of Mineralization.....579 X. General Conclusions.....580 I. Introduction. The object of this paper is to present a concise statement on the genesis of the copper- and lead-deposits of the Bingham

Jan 1, 1906

By Charles W. Carter, Alfred H. Bell

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By Alfred H. Bell, Charles W. Carter

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By J. A. Berger, R. J. Towner

A method for determining the disorientation between sub-grains that .share a common tilt or twist boundary from measurements on X-ray micrographs is described. The method may be applied to subgrains of almost any orientation having boundary angles in the range from about 1 min to 1 deg of arc. An adaption of the Berg-Barretl method has been made to allow calculation of small angles of about 1 min to 1 deg of arc: between adjacent subgrains from the relative displacement of their images on X-ray micrographs. schulz4 gave equations for determining subgrain disorientation where the axis of subgrain rotation and the reflecting crystal planes were parallel to the specimen surface. In our method, however, they need not be parallel and, indeed, may have va:rious orientations. His camera setup, involving a fine-focus X-ray tube for obtaining high resolution with continuous radiation, was different from the one used in the present investigation (a 1.2 x 1.2 mm effective source and characteristic radiation). The X-rays produced a slight magnification in the subgrain images in the Schulz method, but not in the present method. The commonly available type of X-ray tube used permitted relatively short exposure times with a fine-grained photographic plate, which could be magnified optically many times for the examination of small subgrains. The method is illustrated by results obtained on {110} tilt boundaries in a polygonized aluminum single crystal of 99.994 pct purity. The flat crystal was stretched 6 pct in tension and then heated at 500°C for a cumulative time of 5 hr. Earlier, cahn5 studied subgrains formed by polygonization in stretched and heated aluminum crystals. He observed kink bands to have well defined boundaries lying in (110) planes, at least in the early stages of deformation. Cahn found that the (110) tilt boundaries formed by polygonization were directly related to the lattice bending about the <211> axis which lay in the (111) slip plane perpendicular to the <110> slip direction. DESCRIPTION OF THE CAMERA Our camera was similar in detail to Honey-combe&apos;s.6 Unfiltered copper radiation was used at 35 kv, and 20 ma. With the particular specimen used here to illustrate the method, a 1.2 by 1.2 mm effective source and a distance of 780 mm from target to specimen were employed, giving a convergence of 5 min of arc in the primary beam. The distance was 9.5 mm from the specimen to film. The upper 1/2- by 1-in. portion of the front surface of the specimen was irradiated with the film in parallel position. Since the specimen had been inhomogeneously deformed, many regions were in a position to reflect characteristic radiation at the Bragg Angle. Five minute exposures were satisfactory with Kodak Single Coated X-ray Film, 1 1/2 hr

Jan 1, 1961

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick&apos;s second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method&apos; are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5&apos; could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5&apos; or Ag&apos;lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5&apos; and 0.6 N HNO3 solution for the A"&apos;), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5&apos; atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer&apos;s Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.00 Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors&apos; Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

The official Institute reports for the year 1929 were distributed in pamphlet form at the Annual Meeting, February, 1930, and were later included in Section 2 of Mining and Metallurgy, June, 1930, and thus made available to the entire membership. Membership In its report the Admissions Committee set forth the changes in membership during 1929, as follows: Total membership, Jan. 1, 1928, 8582; elected and placed on rolls in 1929, including 59 reinstatements, 509; loss by resignations in 1929, 88; loss by death in 1929, 110; loss by suspension in 1929, 37; membership at end of year not including Student Associates, 8856. Distribution of membership: Honorary Members, 16; Members, 6590; Junior Members, 38; Associates, 1041; Junior Associates, 1033; Rocky Mountain, 138; total membership, Jan. 1, 1930, 8856; Student Associates, 150; total including student associates, 9006. Treasurer&apos;s Annual Report, Year of 1929 Statement of Receipts For the year ended December 31, 1929 Dues: Arrears............................................ $ 3,501.75 Current............................................ 97,257.12 New Members...................................... 5,721.50 Advance........................................... 1,970.79 $108,451.16 Initiation Fees.................................................. 7,436.OO Magazine Receipts: Advertising Gross Receipts........................... $40,610.81 Magazine Sales..................................... 3,799.84 44,410.65 Sale of Transactions Current........................... $ 2,985. 15 Sale of Special Editions Current........................ 5,147.82 Sale of Back Transactions and Special Editions........... 4,186.93 Sale of Year Book..................................... 65.50 Sale of Authors&apos; Reprints.............................. 2,585.40 Sale of Pins and Fobs.................................. 14.73 Sale of Technical Publications.......................... 1,451.55 Sale of Bindings...................................... 3,949.13 20,376.21 Net Interest Received: On Bank Balance and Temporary Investments......... $ 2,595.04 On Lie Membership Fund........................... 3,223.43 On James Douglas Library Fund...................... 5,425.61 On General Reserve Fund............................ 2,015.58 13,259.66 Miscellaneous Receipts........................................... 335.80 Total Receipts................................................ $194,269.48

Jan 1, 1930

By K. R. Evans

The yield and fracture characteristics of a Ti-8 pct A1 alloy have been examined at room temperature as a function of exposure temperatures to 1700°F. Em-brittlenzent of the alloy is observed to occur following exposures below 1280°F, the critical temperature for formation of ordered Ti3Al particles. Presence of Ti3Al particles results in an increase in the yield and flout stresses which, for a given exposure time, are a maximum at the critical temperature. Embrittlement is attributed to the occurrence of plastically induced fracture controlled by the increase inflow stress. This interpretation is compatible with the decreasing ductility and increasing crack popagation rates observed with increasing exposure time below the critical temperature. Slip line observations and measurements of the gain size dependence of the yield stress indicate that the slip character of the alloy is not influenced by exposure treatments below the critical temperature. ThE potential usefulness of Ti-A1 alloys in structural applications has prompted considerable interest in studies of their microstructure and mechanical characteristics. The relatively recent surge of interest in the system and at the same time its complexities are indicated by the fact that despite numerous recent efforts14 there has not even been general agreement upon a phase diagram for the system. However, most of the Ti-A1 alloys of commercial interest range in aluminum content from 5.0 to 8.5 wt pct where most investigators achowledge the existence of the ordered Ti41 phase. Goldak and parrs confirmed the existence of Ti41 from X-ray diffraction analysis of the stoichiometric composition while Blackburn6 has determined its presence in commercial Ti-8 pct A1 alloys by electron diffraction analysis and dark field transmission microscopy. The embrittlement of Ti-8 pct A1 alloys was initially reported by Crossley and carew7 who showed that aging in the temperature range of 750" to 1110°F resulted in extreme brittleness. This behavior was later confirmed and correlated by Soltiss to the presence of long-range order in the commercial Ti-8 pct Al-1 pct Mo-1 pct V alloy (Ti-8-1-1) which exhibited anomalous creep and yield strength behavior at 950°F. This investigation was designed to study the mechanical characteristics of a binary Ti-8 pct A1 alloy in order to further examine the nature of the embrittlement behavior reported for the alloy system. EXPERIMENTAL PROCEDURE A Ti-8 pct A1 binary alloy was obtained from the Wah Chang Co. in the form of 0.050 in. sheet. The chemical composition of the alloy is given in Table I. Heat-treatment of the alloy was conducted in evacuated vycor capsules for the tensile sDecimens (1.25 bv 0.25 in. gage section) and in evacuated stainless steel jackets for the crack growth-rate panels. All specimens were annealed at 1700°F for 24 hr and water quenched before an exposure at elevated temperatures. Tensile testing was conducted at room temperature in an Instron testing machine equipped with a pushbutton control for instantaneous control of the cross-head motion. In this manner the change in stress, Aa, accompanying an increase in strain-rate by a factor of 10 was measured immediately after yielding. The crack growth-rate panels used were 3 by 18 in. with a precrack 0.33 in. long cut into the center of the panel. The panels were cycled at a maximum gross stress of 40,000 psi at a maximum to minimum tension stress ratio of 20. Cycling of the specimens was continued until the crack propagated the width of the panels. The crack length was intermittently measured during slow crack growth. EXPERIMENTAL RESULTS Correlation of Embrittlement to the Critical Temperature for Ordering. Blackburn6 has found that the critical temperature, T,, for the formation of Ti41 in a Ti-8 pct A1 alloy with an interstitial content on the order of that given in Table I is approximately 1245°F. The relationship between the ductility of the binary alloy used in this investigation and T, was estimated from tensile tests on specimens which were exposed for 24 hr at various temperatures followed

Jan 1, 1970

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

.In a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. Consequently since a technical cohesion limit is defined as the technically deter-minable resistance to fracture under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. In the general investigation described in the previously-mentioned papers, 10-18,20,21,23 the influence of the stress system on the fracture stress was studied by means of tension tests of notched specimens. When a circumferentially notched cylindrical specimen is subjected to longitudinal tension, the minimum cross section is under transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S1), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (Sz = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (s3/s1) The evidence is based not only on the results of tests to fracture at various constant temperatures, but also On results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1949

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-&apos;. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines &apos; has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a &apos;molecular fingerprint&apos; of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward&apos;s Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-&apos; was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-&apos;. The ratio obtained by dividing absorbance at 1623 cm-&apos; by absorbance at 1868 cm-&apos; was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the&apos; shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress &apos;system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical&apos; specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By J. P. Nielsen

When two grains in a polycrystalline specimen meet at a point in the course of grain-boundary movements, and the new boundary created at the point is one of relatively low specific free energy, a nonequilibrium boundary condition occurs. The nonequilibrium is enhanced if the other grain boundaries involved at the point of meeting are relatively high in specific free energy. The nonequilibrium results in a correction by growth of the complex grain (two subgrains) to a large size, sufficient in many cases for it to become a self-propagating unit, i.e., a recrystallization grain. This mechanism, herein called "geometrical coalescence," is proposed as a logical origin for recrystallization nuclei, particularly for secondary recrystallization. RECENT publications1-&apos; indicate that considerable progress has been made toward a complete understanding of the three microstructural processes in metals: recovery, recrystallization, and grain growth. However, a major problem persists, namely, the origin of recrystallization nuclei. It is generally accepted that once a recrystallization nucleus, a secondary recrystallization nucleus particularly, has reached a certain size, it will continue to grow at the expense of its neighbors, simply as a consequence of grain-boundary free-energy considerations. What has remained obscure, however, is the mechanism whereby such a nucleus comes into being and grows to the self-propagating size. Recrystallization Nucleation in a Two-Dimensional Grain-Boundary System In the left portion of Fig. 1 is shown schematically the meeting of grains 1 and 4 on disappearance of boundary 2-3, i.e., the boundary that existed between grains 2 and 3, as might happen in the course of normal grain-boundary migration. If, by chance —and the probability is not necessarily small— grains 1 and 4 are close together in their mutual orientations, or in some other special way mutually oriented so that the new common boundary has relatively a very low specific free energy (hereinafter referred to by s), then the grain boundary arrangement as depicted in the figure is highly unstable. This is particularly so if boundaries 1-3, 3-4, 4-2, and 2-1 are high in their s values. Assuming, for the sake of argument, that boundary 1-4 has a s equal to zero, and the s&apos;s of all the other boundaries present are equal to each other and constant, then the boundary arrangement on the right in Fig. 1 will be

Jan 1, 1955

By F. W. Jessen, C. A. Johnson

The effect of treatment with ferrochrome lignosul-fonate on both sodium and calcium bentonites has been examined. In the early stages of treatment it appears that some base exchange of iron and chromium for sodium may occur with the sodium bentonite. Such exchange appears specific for exchange of sodium ions when the calcium ion concentration represents 40-5.5 per cent of the total exchangeable cations, and when additions of lignosulfonate are less than 1 lb per bbl. Adsorption appears entirely physical above 1 lb per bbl treatment level for all concentrations of calcium studied. Gel strength and plastic viscosity of both calcium and sodium bentonite systems were reduced with treatments of ferrochrome lignosulfonate up to 2 Ib per bbl, the greatest reduction occurring within a range of calcium concentration of 40-5.5 per cent of the total exchange capacity of the clay. INTRODUCTION The problem of control of viscosity and gel strength of drilling fluids by the action of thinners or dispersants has been studied by many investigators.1-7 In addition, much work has been done on formation of gel structure in clay suspensions. However, gel formation and structure still are incompletely understood, and the use of the various dispersing chemicals is based, to a large extent, on data almost entirely empirical in nature. In recent years the lignosulfonates have become increasingly important in the treatment and control of drilling fluids. More specifically, ferrochrome lignosulfonate has found rather wide acceptance, particularly in calcium systems.5-7 Lignosulfonates are refined lignin products made from spent sulfite liquor from which the fermentable sugars have been removed.15 The exact structure of lignin is not known; however, it is believed to be a phenolic propane type polymer which may exist as a branched chain or cross linked structure. The molecular weights of lignosulfonates probably range from 300 to 100,000 or more.15 A better understanding of the mechanism of adsorption of dispersants is essential before improvement and development of characteristics of drilling fluids and drilling fluid control is possible. This investigation was undertaken to determine the action of ferrochrome lignosulfonate on sodium and calcium montmOrillonite&apos; LABORATORY INVESTIGATION A Stormer viscosimeter and Fann V-G meter were used to measure viscosity and gel strength. A Zeiss spectrophotometer was used for analysis of Fe and Cr and the flame attachment was employed in the analysis of Na, Ca and Mg. A General Electric X-ray diffraction unit utilizing Copper Ka radiation and a Ni-filter was utilized in the X-ray studies. PROCEDURE Two systems were studied. Predominately sodium clay, obtained from Wyoming, and a predominately calcium clay from Texas were used. These particular samples were chosen because of the extensive work of characterization completed by Mungan. Ionic base exchange capacity determined by flame photometry and total exchange capacity by the Kjehldahl method were obtained experimentally. A 7-per cent suspension of the sodium clay and a 20-per cent suspension of the calcium clay in distilled water were prepared by mixing with a high-speed mixer. The suspensions were allowed to stand for two weeks for complete hydration. Calcium chloride was added to portions of the sodium and calcium cla suspensions to obtain suspensions varying in Ca++ concentration as shown in Table I. A series of treatments was run with 500-ml portions of the original suspensions using a ferrochrome lignosulfonate. Treatment was carried out in the same way with each of the suspensions of varying Ca concentration. Viscosity and gel strength were measured and a filtrate obtained at each treatment level. Ten ml of filtrate were diluted to 50 ml, and aliquot portions of the 50 ml were taken for the Na, Ca, and Mg analysis by the flame photometer. The pH of these filtrates ranged from 7 to 7.3. Standard

By Harold B. Fell

MANY oil producers are in disagreement with the idea held by some that an increase in the price of crude oil would be unlikely to stimulate much production and that we will be obliged to draw upon foreign sources of petroleum to supplement our domestic production as the years go by. Supporting our con trary opinion are numerous facts and figures. The most recent official estimate of the maximum efficient rate of production from the oil wells of the United States is 5,271,000 bbl per day. The Economics Advisory Committee of the Interstate Oil Compact Commission estimates, assuming certain supplies from imports and from natural gasoline and benzol, that crude oil require-

Jan 1, 1947

Copper ores from small mines in the area south of Tucson, where the Twin Buttes mine is located, were first operated in the 1880&apos;s. Today this area is one of the great copper mining centers of the world. In 1963, Anaconda Company acquired the property from Banner Mining Company and in recent years joined with AMAX in a 50/50 partnership to work the Twin Buttes property. From the beginning, Anaconda had relied on conveyors to remove overburden, oxide material for eventual leaching, and ore from the open pit. In the large st preproduction stripping program in mining history, Anaconda in a four-year period (1965 to 1969) removed 266 million tons of overburden of an average depth of 500 ft (152 m) lying over the ore body. The alluvium overburden was stripped by scrapers carrying 70 to 80 tons and push-loaded by two D9 tractors operating in tandem. The scrapers delivered their loads to bins which fed a 60 in. (1.52 m) conveyor having a capacity of 8500 tph. The 25% slope belt conveyor, which was 2100 ft (640 m) long, transported the material to the brow of the pit, where it was transferred to an 8300 ft (2530 m) surface belt to a 1000 ton loadout bin. At this point, the overburden was trucked to the sites of the tailings ponds, where it was used for dam construction. During 1976, the one billionth ton of overburden was removed from the Twin Buttes mine. The Twin Buttes quartz monzonite porphyry contains only scattered mineralization of which chalcopyrite is the most abundant mineral, associated with chalcocite, covellite, minor bornite, and several oxide minerals. Oxidation has progressed to variable depths of up to several hundred feet below the base of the alluvium. Because of the depth of the sulfide and oxide ores and hard rock waste, two in-pit crushers and conveyor systems were also installed for their transport out of the pit; and in 1976 a third crusher and conveyor system was installed lower in the pit for waste rock only. The two initial crushing and conveying systems were designed to handle any of three functions: crushing waste to be disposed of by a rail-mounted stacker -conveyor, crushing oxide ore for conveyor and then truck transport to stockpiles for future leaching, and primary crushing of sulfide ore for conveyor transport to the two 30 in. by 70 in. (0.76 by 1.78 m) secondary crushers and the two 7 ft (2. 13 m) standards and four 7 ft shortheads in the third and fourth stage crushing plant. A third standard crusher has been in- stalled recently. Mining is done by 15 yd (11.5 cum) shovels which load 100- and 150-ton

Jan 1, 1978

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969