Search Documents

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylammonium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x10 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x10-5 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle increases slightly with increased pH, but further increase in pH causes a sharp rise in the contact angle to a maximum of about 80º. At pH values above 11.6, the contact angle drops sharply, reaching zero by pH 12.6.

Jan 12, 1957

By A. J. Opinsky, J. L. Orehotsky, L. L. Seigle

TUNGSTEN incandescent lamp filaments possess a typical structure of elongated crystals generated upon heating the silica-alumina doped wire rapidly to 2200°C or above.&apos; It is known that these very long grains exhibit a preferred orientation, but there is disagreement in the literature about the direction. Rosi,2 and later Rieck; reported that the <135> direction of the large grains in doped wire tends to be parallel to the wire axis, but other investigators have reported that <110> is the preferred direction. Some further investigation of the orientations of large grains in tungsten wire is reported in the following. In the first series of experiments, 6-in. lengths of wire were heated rapidly in a bell jar. Current was passed through the wires and within 15 sec the wires had reached the grain coarsening temperature. 2 min was the annealing time. Wires were heated in hydrogen, nitrogen, and vacuum. Later, wires were heated in an evacuated tube furnace in which the tube was brought from 1000°C to the operating temperature within 25 sec and held 5 min at temperature. Temperatures were measured with an optical pyrometer. After heating, the wires were electro polished and etched, and the orientations of the large grains determined by the Laue back-reflection technique. Most of the experiments were carried out on a single spool of 5-mil silica-alumina doped wire, but a few tests were made with 5-mil thoriated tungsten wire and 10-mil undoped wire. 5-mil silica-alumina doped wires were reduced to smaller diameters by electropolishing for one series of experiments. Orientations of the large grains in silica-alumina doped wire heated in various atmospheres are presented in Figs. 1 and 2 as plots of the direction of the wire axis relative to the cube axes of the crystals. For most of the conditions studied, the preferred orientation cannot be described as a single direction, but the points might be said to group themselves about the arc passing through <110> and <113>. This arc is the trace of the (211) planes and contains the <135> and <124 as well as <011> directions previously observed by other investigators. The preferred orientation of large crystals in silica-alumina doped tungsten wire might be most generally described, therefore, by stating that a (211 ) tends to be parallel to the wire axis. This is true also for wires reduced in diameter by etching and furnace heated, Fig. 2, i.e., the recrystallization texture is apparently unchanged upon removal of the outer layers and substantially independent of the temperature gradient within the wire.

Jan 1, 1962

By AIME AIME

YALE UNIVERSITY looked like a top-notch school to "Bert" Phillips in spite of the belief that the college in the home town sometimes looks less attractive than a more distant campus. So Bert, a native of New Haven, earned his B.S., M.S., and Ph.D. degrees from Yale. Immediately after Yale days lie served as metallurgist of the Scovill Manufacturing Co., Waterbury, and then went to the Central Research Laboratories of the American Smelting and Refining Co. at Maurer, N. J., where since 1931 he has been superintendent of research. Bert has contributed to metallurgical literature many reports of studies on the constitution and the physical, metallurgy of copper and copper alloys as well as papers on general nonferrous physical metallurgy.

Jan 1, 1938

By R. W. Raymond

THIS meeting was held in the new home of the Institute, the United Engineering Society Building, 29 West 39th Street, New York City, directly following the Dedication ceremonies. The first session was held in the large Auditorium, Thursday, April 18. The meeting was called to order by Mr. John Hays Hammond, President of the Council, who said Before taking up the reading and discussion of papers, I will call upon Dr. Rossiter W. Raymond, the oldest living past-President of the Institute, who has been in harness almost continuously for thirty-six years, and who has contributed more than any one else to bring this society to its present great success and to establish the reputation of the American mining engineer the world over, for a few words supplementary to those which were uttered to engineers generally, during the sessions of yesterday and the day before. ADDRESS BY R. W. RAYMOND. The generally accepted Darwinian doctrine of the survival of the fittest is sometimes illustrated by persons who are supposed to be the fittest because they have simply survived. I fear that I come under that category. Almost all of my contemporaries in the early history of this Institute have passed away. Only one or two of the original founders remain, and I may fairly say that scarcely any remain who were active at that : time in shaping the organization and the future career of the Institute. In May, 1871, I was thirty-one years old. Next week I shall be sixty-seven years old. All the intervening years have been devoted to the service of this Institute almost continuously, either as President or Vice-President or Secretary. You may easily imagine, therefore, with what pleasure I greet you on this occasion. I am not here to extend to you the welcome of the City - of

May 1, 1907

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as &apos;la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10&apos;5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By T. S. Lovering

GEOCHEMICAL prospecting extends the age-old method of searching out lodes with a gold pan and rationalizes the prospector&apos;s hunch that certain plants are associated with ore. It uses sensitive but cheap and rapid analytical methods to find the diagnostic chemical variations related to hidden mineral deposits. Exploration geologists can gain tremendous assistance from this new tool, although its optimum use is not simple. To bring out the geochemical pattern that reveals the presence of a hidden ore deposit with a minimum number of samples requires a combination of shrewdness, chemical knowledge, and exploration geology. The use of sensitive analytical methods for prospecting had its start in the 1930&apos;s in northern Europe, where Scandinavian and Russian geologists had some success in these early efforts. Very little geochemical prospecting was carried on in the United States at this time, and no sustained interest was manifest until the close of World War 11, when geochemical investigations were started by the Mineral Deposits Branch of the U. S. Geological Survey. The purpose of these investigations was to apply geochemical principles and techniques to surface exploration for mineral deposits. Both the research on analytical methods and the routine trace analyses for field investigations were at first conducted by a single group, but it later became apparent that the trace analyses could be done by men of less experience than that required for successful research on methods. For the past several years there have been two groups of chemists, and although their functions overlap, three of the chemists are chiefly concerned with research, while four to six other men make the trace analyses for field projects. The chemical investigations, as well as the field projects of the Geochemical Exploration Section, concern only those phases of the subject that are appropriate to a government organization; every effort is made to help private industry, but not to compete with it, in finding orebodies. The chief aim of the Section, therefore, is to develop new analytical techniques and publish the results promptly, to carry out field investigations of the fundamental principles of geochemical dispersion, and to field test promising- techniques under controlled conditions. Some routine geochemical exploration work is carried on in connection with DMEA loans, and in district studies where the project chief wishes geochemical information on certain areas for his report. It should be emphasized, however, that geologists of the Geochemical Exploration Section are primarily concerned with fundamental principles underlying the distribution, migration, and concentration of elements in the earth&apos;s crust. To facilitate the use of geochemical methods the USGS has published much information on its methods of analysis and has provided opportunities from time to time for qualified professional personnel to study these methods, to work in the USGS laboratory, or to attend demonstrations of the analytical techniques at the Denver Federal Center. Typical of the research carried on are the problems now being investigated: 1) Development of rapid and sensitive analytical methods suitable to the determination of traces of metals and other minor elements in various materials, such as rock, soils, plants, and water. At the present time attention is being concentrated on U, Bi, Cr, and Hg, and satisfactory rapid trace analytical methods are virtually perfected for U and Bi. Good methods are also available for: Cu, Zn, Pb, Ni, Co, As, Sb, W, Mo, Ag, Nb, Ge, V, Ti, Fe, Mn, S, and P. 2) The relation of geochemical anomalies in plant materials to the geochemical distribution of elements in soils surrounding the plant. 3) A study of the dispersion halos in transported sedimentary cover such as glacial drift and alluvium over known orebodies. 4) A study of the behavior of ore metals in the weathering cycle. 5) A study of the behavior of the ore metals during magmatic differentiation. This requires a study of the distribution of minor metals in fresh igneous rocks and their component minerals in a well established differentiation series and in adjacent country rock. 6) A study of the dispersion of metals in primary halos in the wall rock surrounding orebodies. 7) Regional and local studies of the metal content of surface and groundwater in mineralized and barren areas. Many field projects of the Mineral Deposits Branch also require the services of USGS chemists during their investigation of the geochemical environment of ore deposits. From the work that has been done certain general principles have emerged. Concentrations of an element that are above the general or background value of barren material are called positive geochemical anomalies or simply an anomaly, whereas values less than background are called negative anomalies. The anomalies most commonly investigated in geochemical prospecting are those formed at the earth&apos;s surface by agents of weathering, erosion, or surficial transportation, but more and more attention is being given to primary anomalies found

Jan 1, 1956

By R. W. Raymond

The immense commercial value of the Gayley dry-blast process has been established beyond controversy. The testimony of practical blast-furnace managers, on both sides of the Atlantic, agrees that it reduces the cost of pig-iron about $1 per ton; but from the same testimony it appears that this direct economy does not by any means cover its commercial advantages—in fact, that under conditions frequently encountered in practice, it presents other benefits of even greater immediate financial importance. To this point I shall recur in a later part of the present paper. The history of the reception given to this invention, especially on the other side of the Atlantic, has repeated an experience familiar to American engineers. First, the reports of our practice were rejected as theoretically impossible, according to generally accepted notions and formulas; then the figures were reluctantly accepted; and finally the attempt has been made to explain how they could have been obtained. As to the Gayley dry blast, me Americans have been for several years in the last stage of the discussion, and the rest of the professional world is rapidly coming to it. Meanwhile, the remark has been repeatedly made that, whatever Mr. Gayley&apos;s process may turn out to be worth, it was not an invention on his part, but simply the energetic and persevering execution of a procedure already proposed by others. This question I wish to discuss first in the present paper. I. What Did Mr. Gayley Invent? Realizing that this is not the place for detailed argument on an issue of patent law, I shall not undertake to quote and criticise the publications prior to Mr. Gayley&apos;a first patents. It may be admitted, without such critical analysis, that the possible advantages of removing moisture from the air forced into an iron blast-furnace were recognized and talked about a hun-

Jan 1, 1909

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

By Donald L. Colwell

THIS is a metallurgical war. More than ever before, the mechanized forces and the air-borne warfare are deciding campaigns. Both of these are primarily dependent upon metals. There are two ways of increasing the effective supply of these metals when the demand is greater than the total over-all supply. The American custom, when a shortage of anything develops, is to get more. In the case of some nonferrous metals this has been done. For example, our potential peak output of magnesium will be almost one hundred times the prewar production. Output of aluminun has also been tremendously increased, and production of other metals is being stimulated by every possible means. Our enemies, however, have another successful method of increasing the effective supply of a material, and that is, to eliminate entirely all nonessential uses, and also to use, in essential applications, alternate materials wherever possible. Sometimes, ersatz material is inferior to the original, and consequently does not do the job as well. Often, however, it has been found superior, and many substitute items are now being used both by industry and by the military which will continue even when the original material again becomes available.

Jan 1, 1943

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable &apos;indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By S. A. Braley

THE first commercial production of bituminous coal in the United States was in 1820, and formation of acid in the areas from which the coal was removed began at that time. Thus it is 130 years since the development of mine acid began. The coal operator has had to deal with the acid water produced in his mines, and his losses from corrosion of pumps and equipment have been tremendous. Other industries and the public have been forced to spend large amounts for their water requirements because of the acid discharge from the mines. There are many contradictions in the literature on this subject probably because of variations in the analytical procedures followed and differences in the methods of calculation and reporting. The opinions previously expressed may be summarized as follows: The production of mine acid has been looked upon as a simple chemical reaction wherein the oxygen of the air has reacted with pyrite to produce ferrous sulphate and free sulphuric acid. This reaction appears in many chemistry texts and generally has not been considered worthy of further study. Since the measurement of hydrogen ion concentration or activity was developed and expressed in terms of pH, indicator and instrumental methods for pH determination have become readily available, making it natural to think of it as a measure of acid content. Special purpose analytical methods applicable to potable waters, sewage effluents, and boiler waters, based in general upon the determination of what may be regarded as impurities, have been applied to more concentrated solutions constituting mine discharges, without reference to the fact that these specialized procedures had been developed to serve as operating guides for water-treatment plants. It has been assumed that the pounds of acid deliv- Table I. Showing pH and Titratable Acid of Varying Concentrations of Ferrous and Ferric Sulphates Ferric Ferrous ion Acldfty Ion Acidity (Fe+++) ppm CaCO3 We++) ppm CaCOa ppm PA equiv. PPm pH equiv. 11.200 1.80 30,000 11,200 3.98 20,000 5,600 2.01 15,000 5,600 4.15 10,000 2,800 2.21 7,500 2,800 4.41 5,000 1.120 2.48 3,000 1,400 4.68 2.500 560 2.60 1,500 140 5.00 250 280 2.65 750 28 5.00 50 112 2.81 300 56 3.07 150 28 3.38 75 ered by a mine was roughly a constant varying with the number of acres mined, and that the concentration of the acid in the drainage was inversely proportional to the volume of flow. Increased flow was thought to result in a dilution of the acid produced. When the Sanitary Water Board of the Commonwealth of Pennsylvania established a fellowship at Mellon Institute, the first approach to the problem was to review some of the chemical reactions involved and their relation to acid production. Since the sulphates of iron were among the principal constituents of coal-mine drainage, the first studies were based upon solutions of chemically pure ferrous and ferric sulphate. These are both neutral salts, that is, the iron and the sulphate are equivalent, but they produce acid reactions in water solution because as salts of strong acids with weak bases, they hydrolyze to form acid solutions. Solutions of each salt, of varying concentrations, were prepared and the pH, titrable acidity and iron and sulphate

Jan 1, 1952

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,&apos;&apos;2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By John Dasher, M. C. Chang

The Crucible mine in Pennsylvania, operating on Pittsburgh seam coal, is rated at 5000 tpd. The washing plant, built in 1943, is rated at about 400 tph, using hydroseparator boxes to wash the coarse coal (4 x 5/16 in.) and hydrotator units for the fine coal (5/16 x 0). It is generally acknowledged that gravity concentration equipment cannot be used efficiently to beneficiate coal finer than about 65 mesh. Before the present flotation circuit was installed, Crucible recovered its fine coal slurry, predominantly -24 mesh material, by passing it through a battery of five 14-in. and one hundred and ten 3-in. Hey1 & Patterson cyclones in parallel with a 75-ft Dorr thickener. About two thirds went to the cyclones and one third to the thickener. Underflows from cyclones and thickener were filtered, respectively, in one 12-disk Eimco and two 4-disk Oliver filters fitted with stainless steel cloth. The resulting cakes were added to the coarse metallurgical coal. The filtrates, overflow from the 3-in. cyclones, and thickener overflow were recycled to the coarse coal plant.

Jan 3, 1959

By Roger A. Gregg, Barry J. Piearcey

MANY of the nickel-base superalloys developed recently for use in the as-cast condition exhibit a massive "white-etching" constituent1 in the inter-dendritic regions. Commercial alloys in this category are SM 200,* IN 100, INCO 713, and Nicrotung. The appearance of a similar microconstituent in nickel-rich Ni-A1-B alloys has been reported by Schijbel and Stadelmaier. Their investigation revealed that this constituent was the binary eutectic of the terminal nickel-base solid solution and the inter metallic based on Ni3A1. This binary eutectic is degenerate and NhA1 is the major phase. At lower temperatures the eutectic composition lies within the NkA1 phase field and under equilibrium conditions is single-phase NisAl. Taylor and F&apos;loyd3 have shown that in Ni-Al-Cr alloys containing at least 8 at. pct Cr, liquid compositions which solidify by the eutectic reaction in the nickel-rich portion, precipitate nickel-base solid solution and NiAl rather than nickel-base solid solution and NkA1 in the binary Ni-A1 system. Since the nickel-base alloys contain chromium in excess of 8 at. pct and are further alloyed with one or more of the elements titanium, cobalt, molybdenum, or tungsten, it is possible that the eutectic could contain NiAl rather than NisAl. In addition, Benson4 has reported that in low-nickel austenitic high-temperature alloys, which possess Ni/(Al + Ti) atomic-weight ratios <18.0, the Ni (Al, Ti) phase may precipitate from the melt during solidification. Since SM 200 and similar high-temperature materials were developed from alloys which were designed for solution treatment, the appearance of a eutectic would indicate that the limit of solid solubility has been exceeded. The purpose of this note is to confirm that the massive white constituent in the complex nickel-base alloys investigated is based on the binary eutectic Ni + NbAl and that the limit of solid solubility need not be exceeded to produce it, in common with other observations of cast alloys. Successive polishing of a sample of SM 200 showed that, in agreement with Schobel and Stadelmaier, particles of the constituent were spherulitic and in particular were a) situated between cored dendrite arms, Fig. 1, and b) nucleated at the surface of dendrites, Fig. 2. The Ni/(Al + Ti) atomic-weight ratios for the nickel-base alloys which were observed to contain the massive eutectic constituent in the interdendritic regions are 12.1 (Nicrotung), 9.2 (IN loo), 19.5 (INCO 713), and 14.5 (SM 200). However, the results of X-ray analysis of these alloys in the as-cast condition failed to reveal the presence of the Ni (Al, Ti) phase. An electron microanalyzer was therefore employed to analyze the composition of this constituent in SM 200. The results of analyses of representative particles are as follows5: 8.4 at. pct Ti, 8.8 at. pct Co, 5.5 at. pct Cr, 0.9 at. pct W, 12.8 at. pct Al, and 63.6 at. pct Ni. Assuming that

Jan 1, 1964

James GayleY, New Pork City (communication to the Secretary*) :—The main thing that is sought after in this matter is that all purcliases shall be made by analysis. This is done already in special lines, as in the manufacture of various grades of steel in which phosphorus, silicon and sulphur are specified within narrow limits, and I quite agree with Mr. Cook that specifications, which are over-rigid in unessential particulars, should be avoided, as they defeat their own purpose because unreasonable requirements permitting no variation are practically not fulfilled, and it is impossible to specify grade

Jan 1, 1905

By AIME AIME

UNDER the auspices of the Institute&apos;s Committee on Industrial Preparedness, a symposium was arranged for the Annual Meeting on the subject "Ores, Metals, and the War," with many well-known Government men and industrialists participating. Wilfred Sykes, president of the Inland Steel Co., of Chicago, presided, with C. K. Leith and Clyde Williams as vice-chairmen, Mr. Williams presiding over the latter part of the meeting. On the Auditorium stage in the Engineering Societies Building was a formidable corps of "experts," with an audience of several hundred to hear what they had to say and to ask questions.

Jan 1, 1942

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By S. R. B. Cooke, S. W. Clark

Adsorption of calcium and magnesium by quartz was determined over a wide pH range using flame photometry for solution analysis. A parallelism was noted between calcium adsorption at alkaline pH and flotation of activated quartz by means of various fatty acid collectors. Abstraction of calcium from 100 ppm solutions increased above pH 10.5 until all of the calcium was removed at pH values between 12 and 12.5. Calcium was desorbed from the quartz over the pH range 12.5 to 13.0 and returned to the solution. Precipitation of magnesium hydroxide prevented measurement of magnesium adsorption above a pH of 9.9. A calcium adsorption isotherm determined at pH 9 matched measurements of barium adsorption by other investigators over the range where adsorption corresponded to the equation of a Freundlich adsorption isotherm. In accordance with the Gouy-Chapman theory for adsorption in the diffuse layer, adsorption of the divalent cations under these conditions was four times the adsorption of monovalent sodium. Activation of quartz by multivalent metal cations in flotation using anionic collectors has been studied by many investigators. The occurrence of activator cations in the water of flotation mills makes depression of silaceous gangue very difficult. Alternatively, in some flotation systems it is practical to cause activation of quartz so that it is floated from the desirable mineral values. The present study was initiated to investigate the activation of quartz by measuring adsorption of calcium and magnesium ions as a function of solution pH. Early empirical tests showed that quartz would be activated to flotation using anionic collectors if any of a number of divalent or trivalent metallic cations were present in the pulp.1*2 Subsequent studies by Clemmer,3 Cooke and Digre,4 Cooke,5 Schuhmann and Prakash,6 and Cooke, Iwasaki, and Choi,7-8 showed that flotation depended strongly upon the alkalinity of the flotation pulp, the concentration of the activating cations, and the chain length and structure of the organic collectors used. The concept of the electrical double layer has been applied to the case of the quartz-aqueous solution interface by Gaudin and Fuerstenau,9-10 and by de Bruyn 11 to explain the activation of quartz by multivalent metal cations. Studies of the surface of quartz by Gaudin and Fuerstenau9,10,12 and by Li " using the streaming potential technique contributed much information on the electro kinetic condition of the surface of quartz in the presence of various organic and inorganic ions. Measurement of adsorption of ac-

Jan 1, 1969

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3&apos;4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946