Search Documents

By Ulick R. Evans

I Should like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country—researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. Films Produced at Elevated Temperatures If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By Michael Tenebaum, C. C. Brown

In recent years, the importance of slag control in basic open-hearth operations has been universally recognized. To effect such control during the working period of the heat, methods have been developed to measure or estimate slag oxidation and slag basicity. While satisfactory rapid chemical methods have been developed to determine slag oxidation, no completely adequate method of evaluating basicity has yet been provided. The most generally accepted control methods of measuring slag basicity are based on visual cstimates. While considerable benefit may be derived from such estimates, the need for some measurable indication of slag basicity has become increasingly apparent. In a recent paper, Philbrook and Jolly suggested a promising technique for making the basicity determination. Their method consists of measuring the pH of a mixture of powdered open-hearth slag and distilled water. It was found that a relation could be established between the slag basicity and the alkalinity of the water mixture as measured by the hydrogen-ion concentration. The general procedure followed in making the measurements and the considerations involved in constructing the original curves are given in the paper of Philbrook and Jolly and need not be repeated. It is the purpose of this paper to discuss some of the factors considered in applying the pH measurements to actual slag control and to present some of the results of its apphcation. Factors Involved in Measuring pH of Water-slag Mixtures To facilitate the application of the pH control system, it was desirable that no alteration be made in the routine methods of sampling and crushing the furnace slag. Some of the factors considered before establishing a curve to relate slag basicity with the pH reading arc reviewed individually in the following paragraphs. Effect of Cooling Rate Under actual operating conditions there can be considerable variation in the temperature of the piece of slag crushed for the pH determination. To determine whether variations in crushing temperature or in cooling rate would affect the pH reading, a series of four samples was prepared from each of two separate slags. These samples represented conditions far more extreme than would actually be encountered. To obtain these samples, a thick pancake of slag was poured. One piece of this pancake was crushed immediately after it had solidified. Another piece was water-quenched and then crushed. A third piece was allowed to air-cool to room temperature before crushing. The fourth sample was prepared from a chilled slag. This sample was poured onto a heavy inclined steel plate at the

Jan 1, 1945

By J. J. Demo

The effect of aluminum additions on the coating vale and corrosion resistance of Cr-Fe diffusiou coalings on a mild steel substvate has been studied. Aluminum additions up to 2 wt pct increase the chromium penetration rate while further additions retard it. The apparent cor$lict between these data and metallogyapkic ineasurements, which show a continuially increasing coaling thickness with aluminum addition, is discrissed. Compavisorz of corrosion resistance on the basis of equal thickness of tlre entire coating measured mnetal- ALTHOUGH ferrous metal articles are cheap and widely used, they are often quickly degraded by corrosion. To prevent or slow down the corrosion process, lographically is misleading; equal thickness of the cor-rosion-resistant portion of the coating is a bette.v basis of conzpavison. Inter difision coefFicients for Cr-Al-Fe coatings of different aluminum content have been detevmined and found to dary logarithmically when plotted againnst chromium concentvation. A general method of calculating diffusion profiles for different lrealment limes and surfuce coucentralions IS described. many types of coating are applied to steel.' Among these are diffusion coatings, formed by high-temperature diffusion of selected elements into the surface, which then becomes the coating Diffusion coatings are metallurgically bonded to the substrate and show a continuously varying concentration gradient from surface to substrate. Generally, these coatings have the advantage of adhering to the substrate upon deformation of the composite. Moreover, when chromium is one of the diffusion elements, a mild steel substrate

Jan 1, 1968

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the lnspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore-bodies. FROM 1915 to 1948 the entire production of Inspiration Consolidated Copper Co. was supplied from underground mining. The sole method used was block caving. Underground haulage and hoisting facilities were designed and geared to large-scale production. Beginning in 1948 open-pit mining was substituted for block caving in a portion of Inspiration's Live Oak orebody. The idea proved so attractive that before the Live Oak pit had come into production, another pit on the Colorado orebody (now the Thornton pit) had been laid out and stripping started. It should be noted that these orebodies were not new and the entire program was one of changed methods of mining. Since part of these orebodies had already been mined by block caving methods, it must be recognized that haulage levels had been established under the area or adjacent to it. The orebodies lay on the south side of Inspiration Ridge, while the shafts, crushers, and treatment plants are all on the north side of this ridge. The existing main crushing plant was designed to take a maximum of 12-in. material, and all ore was sized to this dimension by passing through grizzlies in the stopes. In the original planning for open-pit work much thought was given to the transfer of ore to existing underground levels for haulage and hoisting from the regular shafts. If this could be done the necessity of crossing the ridge could be eliminated. Final decision called for cutting a road through the ridge, installation of a primary crusher at an elevation of 3968 ft on the north side of the ridge, and railroad haulage with existing facilities to the main coarse crusher. This decision was brought about by the difficulties of properly sizing and transferring to underground haulage large tonnages of coarse breaking oxide which lay on the upper benches of the proposed pit. Trucking over the ridge on a 7 pct grade would give a cheaper and more flexible operation in handling this material. The benches in the pits are laid out at 50-ft inter-vals and designated according to elevation above sea level. The lowest bench in the original pit was laid out at 3500-ft elvation. All haulage roads are on a 7 pct grade and a vertical lift of 468 ft was considered about the maximum economically possible from a cost standpoint. After 2 years' operation the advantages of pit mining, both from the standpoint of costs and flexibility of operation, became more and more apparent. Studies were then started to develop the extension of open-pit mining to more of the ore reserve than had been planned originally. The idea of transfer raises was again explored. Obviously, as elevation of the pit was lowered, shorter transfer raises would be needed to reach the main haulage levels. Transportation from the lower elevations to the rim of the pit by belt conveyor or skip hoisting was also considered. However, it was recognized that sizing would be required both for conveying and regulation of feed size to the main crusher plant. This would necessitate a fixed or portable crusher located somewhere in the pit. It was known that the sulphide ore at the lower elevations was softer and easier to break than the overlying oxide of the upper benches. This sulphide ore is very suitable for grizzly sizing. Calculations indicated that for ore mined on 3650 elevation, costs for trucking to the primary crusher, crushing, and delivery by railroad to the coarse crusher would equal costs for dropping the same material to the 600 level, hauling underground, and hoisting directly to the coarse crusher bins, provided a suitable method of sizing and transferring could be developed. Above 3650 elevation costs would favor surface haulage; below they would favor underground haulage. The idea of caving an underground block from the 600 haulage level directly into the bottom of the pit

Jan 1, 1954

By W. D. Robertson, H. Conrad

Incremental loading creep tests were conducted on magnesium single crystals in tension and direct shear at 78" to 364°K. The creep curves were transient in character and exhibited waves or periodic behavior, especially at small strain rates. A sigmoidal curve was frequently observed following the first occurrence of creep. Repeating of segments of a master curve was observed at all temperatures indicating that identical conditions for flow existed after various stress and strain histories. A logarithmic time law with a independent of temperature whs observed at 78°and 203°K, while a parabolic (power) time law was approximated at 298" and 364°K. The departure from logarithmic creep was attributed. to recovery, which was observed at 298" and 364°K. The temperature independence of a represents a serious objection to the theory of low-temperature creep based on the intersection of dislocations. IN a previous paper1 it was found that the initial creep rate of magnesium single crystals, y, following the addition of a stress increment in the range of 78° to 364°K, was given by the expression ? = C exp - {?H/kT} exp {B(T- h ?)} [1] where B and C are constants, AH is an activation energy of 10,300 cal per mole, T is the applied stress, ? is the total strain at the time of the stress increment, and h is the strain-hardening coefficient. The present paper is concerned with certain other features of creep behavior observed during this investigation; namely, the form of the creep curves, time laws for creep, recovery, and microscopic and X-ray observations of the structural manifestations of the creep flow. To the authors' knowledge the temperature range of the present investigation (0.08 Tm to 0.40 Tm) has not been covered previ-

Jan 1, 1959

By W. R. Crane

The effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. Drainsge in these mines has been discussed in papers on mining practice,' but the fact that water, varying from 0.16 to 3.46 and averaging 1.43 times the amount of ore mined, has to be pumped from the mines daily, indicates the importance of the problem and the advisability of making a thorough investigation of the source of mine water, its mode of entry into the mines, its effect upon mining conditions, and consideration of means of improving the conditions.

Jan 1, 1927

By Allan J. Clark

It may be said that the history of gold in the Black Hills begins with one of South Dakota's most. interesting relics, the so-called Thoen Stone, now in the Adams Memorial Hall at Deadwood. This slab of reddish sandstone, about 14 in. square, was found in by Louis and Ivan Thoen, at the base of Lookout Mountain, near Spearfish, a town in the northern foothills of the Black Hills uplift. Both sides of the stone bear clearly legible inscriptions. One side reads: Came to these hills in 1833. Seven of us, De Lacompt, Ezra Kind, G. W. Wood, T. Brown, R. Kent, Wm. King, Indian Crow. All ded but me, Ezra Kind. Killed by Indians beyond the high hills. Got our gold June 1834. On the reverse side: Got all the gold we could carry. Our ponys all got by the Indians. I hav lost iny gun and nothing to eat, and Indians hunting me. Attempts were made to trace these men. Relatives of Brown were found in Missouri, and it was learned that he had left for the West in 1832, with one Kent. Kind's relatives were also found, and stated that he had started West the same year. None of them had been heard from since their departure. So Kind failed to get out with "all the gold we could carry"; 15 years later California became the center of the first great gold rush, and the Hills waited 40 years for their gold to be rediscovered. It is interesting to speculate on what might have been "the course of Empire" had this little group won through. The history of Dakota, of Montana, indeed, of all the Northwest, might have been very different. When, late in 1875, the goldseekers arrived, they passed quickly northward from the first discovery near Custer, and soon were established on Deadwood Creek, along which, as well as for short distances above the mouths of its tributary streams, Blacktail and Bobtail, placer operations went forward vigorously. These placers were near the northern outcrop of the Homestake ore-body. Their gold was partly derived from this, perhaps in greater quantity from the erosion of the conglomerate or cement deposits, of Potsdam time, themselves a "fossil placer" or beach deposit formed by

Jan 1, 1935

By Thomas Cox

The following compilations are made from a series of investigations and are used to present the subject in an unbiased manner, as the writer does not represent any company or financial interest. The present situation is complex. The producers are hard pressed by reason of the low price of crude, while the independent refiner is little better off, because of the corresponding cut in price of refined products, except on occasional contracts. If the real costs are analyzed, it will be seen that the land speculators and the lessors—royalty owners—make the larger profits and not the struggling legitimate operator or independent refiner. The present-day (October, 1922) posted prices per barrel for crudes are Kansas, Oklahoma, Mexia, Gulf Coast, and Louisiana..... $1.25 Healdton............................................. 0.75 Northern Texas and Central Texas...................... 1 . 50 Pennsylvania......................................... 3.00 Wyoming, Elk Basin.................................. 1.25 Wyoming, Salt Creek................................ 0.70 California Base..................................... 0.60 These prices are at the well. In addition, crudes must be gathered and transported to refinery (by pipe line or tank cars), refined, and the refined products marketed. These crudes are of various gravities, ranging within a narrow margin for each field or district, so that averages are not difficult to deduce, and it is these averages that really determine the average operating conditions. In order to show the present realizations, the prices and costs now obtaining are listed against the average yields; the figures are also adjusted VOL. urn.----71

Jan 1, 1923

By Thomas Cox

The following compilations are made from a series of investigations and are used to present the subject in an unbiased manner, as the writer does not represent any company or financial interest. The present situation is complex. The producers are hard pressed by reason of the low price of crude, while the independent refiner is little better off, because of the corresponding cut in price of refined products, except on occasional contracts. If the real costs are analyzed, it will be seen that the land speculators and the lessors—royalty owners—make the larger profits and not the struggling legitimate operator or independent refiner. The present-day (October, 1922) posted prices per barrel for crudes are Kansas, Oklahoma, Mexia, Gulf Coast, and Louisiana..... $1.25 Healdton............................................. 0.75 Northern Texas and Central Texas...................... 1 . 50 Pennsylvania......................................... 3.00 Wyoming, Elk Basin.................................. 1.25 Wyoming, Salt Creek................................ 0.70 California Base..................................... 0.60 These prices are at the well. In addition, crudes must be gathered and transported to refinery (by pipe line or tank cars), refined, and the refined products marketed. These crudes are of various gravities, ranging within a narrow margin for each field or district, so that averages are not difficult to deduce, and it is these averages that really determine the average operating conditions. In order to show the present realizations, the prices and costs now obtaining are listed against the average yields; the figures are also adjusted VOL. urn.----71

Jan 1, 1923

By K. Osseo-Asare

The thermodynamics of solid-aqueous solution equilibria up to 200°C In the systems Me-NH3 H2 0 (Me=Cu, Ni, Co) are summarized with predominance area diagrams generated with the DIAGRAM computer program. The implications of the diagrams to ammonia hydrometallurgy are discussed.

Jan 1, 1981

By Michael P. Robinson

It has been suggested that streaming potentials are not nomlally logged because the streaming potentials known to be generated across mud filter cakes are substantially cancelled by streaming potentials generated in contiguous shale beds. Laboratory measuments of streaming poterztials acrons hand specirnens of shale have been adduced as evidence to support the suggestion. The experiments show that streanzing potential depends on the resistivity of the equilibrating solution and on pressure drop. Meizsurenlents were made perpendicular to the bedding planes of the shales. The mechanism of streaming potential generation in shale which the suggested cancellation theory iniplies has been critically examined. Conclusions reached are tested by comparing self potentials logged before and immediately after changing the resistil~ity (but not the weight) of mud in a borehole. The resultant SP change is found to equal the theoretical electrochetnical potential change, i.e., cancellation of .strearning potential is independent of mud resistivity. Since streaming po/entials generateal across mud filter cakes depend critically upon mud reistivity, shale .strearlling potential in situ must he equally sensitive. Using plausible values for the pemleahility, porosiy arzd compressibility of shale, the van Ererdingerl-Hurst approach shows that the pressure drop between horehole pressure and formation pressure in a radially honzogeneous shale is unlikely to coincide with the zone of filtrate invasion. If, perchance. this coincidence occurs with one mud a chatzge 10 a second must result in non-coincidence, i.e., a .YP logged in the second mud should show a streaming potenlial. The dilernrna may he overcome by postrrlating: (I) perrneabilities of shale7 parallel to their beddine planes greatly exceed their cross-bedding permeabilities; (2) a resistivity-sensitive mud cake of low permeability forms either on the face of, or probnhly in the lanlinations of, many shales. These postulates are examined with reference to the pres.sure and SP histories of the McClosky and Aux Vases zones in the Illinois Basin and some srcpport for them found. It is concluded that a definitive solultion to the streaming potential problem does not exist. INTRODUCTION Recently Gondouin and Scala' published a contribution to the streaming potential problem which is notable particularly for the elegance of its experimental techniques. The conclusions drawn by Gondouin and Scala from their studies amplified those previously suggested by Schehck'. In essence they suggested that the streaming potentials known to develop across mud filter cakes" are not normally observed on SP logs because they are largely cancelled by streaming potentials generated in adjacent shales. This suggestion appears so reasonable that many workers in the logging field will be prone to accept it. We incline strongly to the view that the suggestion is basically correct. Nevertheless, it is important to realize that the cancellation hypothesis in the form put forward by Gondouin and Scala does not appear to meet all the known experimental facts. It is the principal intention of this note to call attention to what appears to be a flaw in the relevancy of the experimental evidence adduced by Gondouin and Scala and to suggest an alternative hypothesis to remove it. The consequences of the new hypothesis are compared with field data which, we believe, are unique. A second but not less important purpose of this note is to emphasize that even the new hypothesis does not fully explain all field observations. Hence we conclude that further study of the streaming potential problem is required before it can be said that a definitive solution to it has been attained. The bare experimental bones of laboratory data on streaming potentials appear to be as follows. 1. A streaming potential is developed across a mud filter cake. This streaming potential is virtually independent of cake thickness but depends on the mud resistivity. The relationship is of the form, 2. A streaming potential is developed across a shale. This potential is independent of shale thickness but depends on the resistivity of the permeating solution if the shale has been first equilibrated in this solution. The relationship is of the form, The relationship in (1) was determined first by Wyllie3, confirmed by Gondouin and Scala and qualita-

By F. W. Lake

The ultimate production from a natural reservoir of petroleum is inversely proportional to the gas-oil ratios existing during the producing life of the reservoir whenever gas is the major expulsive force in the recovery. In other words, in the period during which gas is the major expulsive force the ultimate production will be increased if the gas-oil ratio is decreased, and vice versa. This condition prevails in the greater number of the present producing districts. While this relation is difficult to prove from actual operation, on account of the present paucity of detailed observations, it must be admitted after a study of the forces and conditions governing the recovery of petroleum from natural reservoirs. Where gas and oil exist under pressure in sand interstices and water movement is not freely possible, the force expended in moving the oil to the well is the expansion and movement of the gas through the pressure differential existing between the interior of the reservoir and the well. If pressure and solution conditions in the untapped reservoir are such that the relation between gas and oil volumes at atmospheric conditions is as 100:1; and if during the producing period, until the gas is exhausted, the relation between the gas and oil volumes produced is 300:1, it follows that only one-third of the oil has been produced and the remaining two-thirds cannot be recovered unless some extraneous force is introduced into the reservoir. This serves to illustrate the importance of gas-oil ratio control during normal producing operations. Gas-oil Ratio Control Eliminating natural conditions in a reservoir, which govern gas-oil ratios, such as the physical properties of the oil and gas, the physical characteristics of the reservoir strata and the original pressure and solution conditions in the reservoir, which cannot be controlled by operation practice; and also eliminating operating conditions that apply to the reservoir as a whole, such as well spacing, well locations, relative completion dates, various penetrations and drilling practice; there remains but one condition in each well that influences the gas-oil ratio and that is

Jan 1, 1928

By G. Koves

The behavior of case-hardened AISI C-1213 free -machining steel under complex impact-fatigue -wear load conditions was investigated. The inherently poor dynamic properties of the steel are mainly affected by the stress distribution in the case, component shape, and tempering. Cold-riveted components showed unexpectedly high dynamic strength compared to basic parts. A compromise beatment—which provides good dynamic properties, reasonable wear resistance, and fair riveting characteristics—zuas developed. A number of mechanical components in data-processing machines are made of free-machining carbon steel. Although, selected primarily due to manufacturing requirements, components made of these grades frequently undergo complex heat treatment and must sustain impact-fatigue loads. A typical free-machining steel is the AISI C-1213 grade, which is a resulfurized and rephosphorized open-hearth steel. While the undesirable effects of sulfur and phosphorus on the mechanical properties are well-known, data on dynamic properties are scarce.1"3 Rapid rotating or oscillating motion while carry- ing a high cyclic load requires a combination of wear resistance with high endurance limit and impact toughness. The inherently poor dynamic properties of the free-machining steel are further degraded by the machining, which introduces local stress-concentration areas. While the heat treatment (usually case hardening) improves some mechanical properties, it necessarily impairs others. Another problem arises when components, such as studs, must be fastened by riveting. The high crack-sensitivity of the free-machining steel, especially in the presence of a hardened case, makes this operation difficult. In view of the preceding considerations, it is of interest to investigate the behavior of a typical component under complex impact-fatigue-wear loading conditions in order to explore the effects of material, machining, and heat treatment, to obtain specific data on the dynamic characteristics of free-machining steel, and to arrive at a process which would adequately utilize the inherent qualities of this material. EXPERIMENTAL PROCEDURE To simulate actual service conditions, a typical component was selected, based on frequency of application, complexity of load, and processing difficulties. The dimensions and shape of the component—a stud used in many electromechanical document-handling machines—are shown in Fig. 1.

Jan 1, 1964

By P. M. Robinson, J. S. LI. Leach

The heats of solution oj' indiurrr, tin, lend, nrzd tellurium have been calculated from the measured heat effects when mechanical mixtres of indium and telLuium tin and tellurium, and lead and tellurium were added to liquid bismuth. The results are in good agreement xith publislzed values.s for the separate sollction of each eleltzent in bismuth. The heats oj solution of cadmium and tellurium calculated from the rneasuved heat effects on adding trechanical mixtures of these elements do not ugree zc,itl the published values jbv the separate solution of each element. It is shown that at 623°K Ile interaction between cadmium and tellurium dissolved in liquid bismuth is strong enough to led lo preciPitation of solid CdTc. The heats oj- jor-mation of CdTe at 273" nd 623°K (1)-c crilculated fi-or the measured heat ejlfecls. The calcnlaled az'erage deviation from the Kopp-l\'ez?,zunrz rule fov solid CdTe is less than 0.06 cat per g-atom- C over this lertzperalure range. Tlze importance 0.f these oDserl.ations to the determination of heals of formation hy metal solution calorimetry is considered. LIQUID metal solution calorimetry is a convenient method for determining the heats of formation of solid compounds. In this technique the heat of formation is the difference between the measured heat effects on dissolution of the compounds and of mechanical mixtures of the components in the liquid metal.' The heat of solution of the mechanical mixture may be calculated from the measured heat effect. At infinite dilution of the solutes, this heat of solution is equal to the sum of the heats of solution of the separate components. If the heat of solution of one of the components is known, the value for the other can be derived; if both are known, they may be used to check the accuracy of the calorimetric technique. The heats of formation of the tellurides of cadmium, indium, tin, and lead have recently been measured by metal solution alorimetr. The heats of solution of indium, tin, lead, and tellurium at infinite dilution in liquid bismuth at 623"K, calculated from the measured heat effects on solution of the mechanical mixtures, are in good agreement with the published values. The heats of solution of cadmium and of tellurium calculated from the measured heat effect on solution in bismuth at 623'K of mechanical mixtures of cadmium and tellurium, however, do not agree with values estimated from the literature. 1) EXPERIMENTAL PROCEDURE AND RESULTS The Heats of Solution of Indium, Tin, Lead, and Tellurium in Bismuth. The heat effects were measured when mechanical mixtures corresponding to the compounds In,Te, InTe, In2Te3, In2Te5, SnTe, and PbTe were dissolved in bismuth. The calorimetric procedure and the method of calculation have been described elsewhere.' The heats of solution of the mechanical mixtures were obtained by subtracting the change in heat content per gram-atom of the sample between the addition temperature (273°K) and the bath temperature (623"K), (H623°K - H273°K)S, from the measured heat effects. The calorimeter was calibrated with pure bismuth. The reported values of the measured heat effects are based on (HGoK - ^273oK)Bi = 4.96 kcal per g-atom.3 The measured heat effects are found to be linear functions of the solute concentrations of the bath in the dilute solution range. The values, extrapolated to infinite dilution, are listed in Table I, together with the heats of solution of the mechanical mixtures calculated using the published values of (H 623°K - H273°k)s for indium, tin, lead,3 and tellrium. All the error limits quoted in this work represent the spread of values obtained. The heats of solution in liquid bismuth at 623°K of mechanical mixtures of indium and tellurium in four different proportions were determined. Values of the heats of solution of the two components were then calculated from the resulting four simultaneous equations: The heats of solution at infinite dilution of tin and lead in liquid bismuth at 623°K were calculated from the heats of solution of the mechanical mixtures of tin and tellurium and of lead and tellurium using the heat of solution of tellurium calculated above. These values of the heats of solution are listed in Table I1 together with some published values for comparison.

Jan 1, 1967

By P. Barnes

(Read at the Amenia Meeting, October, 1877.) THE subdivisions of this account are numbered 27, 28, 29, 30, 31, 32, and 33, in the general series of construction accounts, and give the details of cost of the various items of the work, as noted below: Accounts 32 and 33 -relate to hand-tools and to heaters, and, being quite small in total amount, are omitted in this statement.

Jan 1, 1878

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By Marie L. V. Gayler

Without diffusion taking place in liquid metals and alloys, no castings could be made; it is therefore the most important factor affecting the structure of metals. Diffusion involves the interchange of atoms, a process which takes place during the life history of an ingot. In the liquid, atoms are in a state of high thermal agitation, but this thermal vibration is reduced in amplitude with falling temperature. When solidification sets in, the atoms arrange themselves on an ordered space lattice and the changes in structure which take place in the solid are due to the interchange of atoms on this space lattice. The rate of atomic interchange—e.g., of diffusion—is most rapid at temperatures close to the melting point and decelerates as the temperature is lowered. At room temperature, the rate of diffusion is practically negligible in most alloys, and any change in structure can only be brought about by using methods which will accelerate the rate of diffusion. The rate of diffusion depends on three factors (I) temperature; (2) concentration gradient and (3) activation energy. The growth of grains and particles in the solid alloy also depend on these factors and are therefore intimately associated with diffusion. The rate of homogenization in a cast alloy depends on several factors, such as: (I) rate of solidification, which involves grain and particle size which, in their turn, depend on diffusion: (2) the nature of the constituents; (3) the temperature interval between the melting point of the metal or alloy and the temperature at which it is being heat-treated. It is well known that coarse, cast structures are extremely difficult—if possible— to homogenize, and the finer the grain size and particle size, the more readily solid solution will take place. The rate of diffusion depends, also, largely on the nature of the constituents; for instance, copper and magnesium form solid solutions with aluminum quite readily but nickel and iron do not; neither do certain intermetallic compounds, such as alpha and beta FeSi. Furthermore, the actual formation of intermetallic compounds may be a very slow process, particularly when they are formed in the solid state as equilibrium products. For example, BFeSi is formed in the solid as the result of the reaction aFeSi + A1 —+ PFeSi. The particles of aFeSi become surrounded with a reaction ring of PFeSi. This layer is formed as the result of diffusion of atoms taking place between the aluminum matrix and aFeSi. As the amount of aFeSi surrounding the core of aFeSi increases the concentration gradient becomes low and so the rate of diffusion of atoms also decreases until it practically ceases. This occurs after a comparatively thin layer of ßFeSi has been formed. It follows that when intermetallic compounds of this type are formed in the solid, as the result of diffusion, it is generally impossible ever to attain equilibrium, since the forma-

Jan 1, 1944

By E. R. Kaiser

COAL research during 1942 was directed in an important degree toward the solution of problems of wartime importance. A wider selection of coals for carbonization to meet the increased demand for coke, and the improved utilization of lower-grade coals for boiler fuel were made possible by fundamental studies on cod and ash behavior that had been started several years ago. The coal industry's interest in the work of the various laboratories brightened significantly as results were demonstrated on smokeless combustion in stoves, on stokers without coke trees, and on pulverized firing of forge furnaces. Despite the limitations of priorities and scarcity of materials, the mineral industries building of the West Virginia University was completed and equipped with facilities for research on coal min

Jan 1, 1943

By P. Niessen, S. J. Bercovici

RECENTLY Aust et al.&apos; proposed a model of non-equilibrium grain boundary segregation based on a vacancy gradient induced uphill diffusion process of solute to grain boundaries. According to their proposal, solute atoms which are attracted to vacancies would, during the cooling of a sample, migrate with vacancies toward grain boundaries (vacancy sinks) and thereby enhance the solute concentration in boundary regions. For solute atoms which are not attracted to vacancies no such boundary solute enrichment would be expected. These concepts were given experimental support by boundary and bulk mi-crohardness measurements of various thermally treated dilute zinc and lead alloys and also doped aluminum oxide. The underlying assumption in their work was that solute enrichment in boundary regions is indicated by higher microhardness values. From thermodynamic considerations1&apos;2 it appears that the solid-liquid solute distribution coefficient (K), defined as the concentration of solute in the solid to the concentration of solute in the liquid at equilibrium, indicates whether attractive or repulsive forces exist between vacancies and solute atoms. K < 1 indicates a solute-vacancy attractions, K > 1 indicates no, or a repulsive, vacancy-solute interaction. This note is to report on observations of different grain boundary etching phenomena in high purity zinc alloys. These phenomena appear to depend on whether a K < 1 or K > 1 solute is present. In experiments designed to measure directly the solute enrichment in grain boundary regions, samples of zone refined zinc with 0.1 at. pct solute additions were cooled from 380°C at a rate of 3°C per min. A surface layer of approximately 50 was then removed from the samples by chemical polishing. The samples&apos; surfaces were then protected by a chromating treatment such that in a subsequent etch only grain boundary regions were dissolved. The dissolved regions were approximately semicircular troughs, 10 µ in width. The grain boundaries were usually in the middle, i.e., at the bottom, of this trough. For zinc containing the K < 1 solutes cadmium and aluminum, the grain boundary was always indicated by a ridge as shown in Fig. 1. For pure zinc, and zinc containing the K > 1 solutes copper and gold, a groove at the bottom of the trough indicated the boundary position, Fig. 2., To test if these different grain boundary etching behaviors were possibly connected with the segregation process discussed above, the Zn-Cd alloy was again heated to 380°C and quenched into brine. After surface protection and etching it was found that this specimen no longer exhibited the grain boundary ridges but rather grain boundary grooves as shown in Fig. 2. It would appear, therefore, that the boundary ridge is a consequence of a process occurring during the slow cooling of the samples. From absorption spectrophotometric analysis it was found that for slowly cooled samples containing K < 1 solutes, the solute/zinc ratios of the material from the boundary trough were consistently considerably higher than the solute/zinc ratios of the bulk alloys. This boundary region solute enrichment was not observed in quenched samples. It is concluded therefore, that the boundary ridge shown in Fig. 1 is directly or indirectly connected with nonequilibrium solute segregation.

Jan 1, 1970