Search Documents

For the year ending February, 1918 PRESIDENT PHILIP N. MOORE, ST. Louis, Mo. PAST 'PRESIDENTS WILLIAM L. SAUNDERS NEW YORK,. N. Y. L. D. RICKETTS NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, _ NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 11, 1917

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley's paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley's formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881

By A. W. Cochardt

MOST of the current high temperature materials are precipitation-hardened alloys. These alloys are usually soft when quenched from a solution heat-treatment temperature, but become harder

Jan 1, 1958

By G. Wakefield, A. H. Daane, D. H. Dennison, F. H. Spedding

Preparation of pure scandium metal was accomplished by calcium reduction of the fluoride by two methods; a low-temperatzdre alloy process and direct reduction with subsequent distillation of the product. The following properties were determined: melting point: 1181OK; boiling point (calculated): 3000°K; lattice constants at 298°K (hexagonal lattice): a = 3.308 * 0.001 A, c = 5.267 * 0.003A; calculated density at 298°K, g per cm3: 2,990 + 0.007; electrical resistivity, ohm-cm: 299°K, 66.6 ± 0.2 x 10 -6; 373oK, 77.4 * 0.2 x 10 -6; thermal coefficient at 299°K, ohm-cm per deg: 5.4 X x; heat of sublimation at 298°K, kcal pel- mole: 80.79. The vapor pressure was determined as a function of temperature between 1505o and 1748°K, with the data fitted to a straight line shielding the equation: Log Pmm = -1.718 X 104/ToK + 8.298. SCANDIUM, element number 21, was first discovered by Nilson in 1879 and was recognized as the Ekaboron as predicted by Mendeleff. As it is in group III of the periodic table, the general properties are a little like aluminum and also resemble quite closely the properties of yttrium and the rare-earth metals, in both the metallic and ionic form. Although the earth's crust contains approximately 5 ppm of scandium (the element is as abundant as arsenic and twice as abundant as boron) it generally occurs so widely distributed that it has earned the reputation of being very rare. The one exception to this is the mineral thortveitite, which has been found in Madagascar (20 pct Sc2O3) and in Norway (35 pct Sc2O3). Scandium also occurs in small but distinct amounts in uranium and rare-earth ores; the recent larger scale processing of these materials has made some scandium available from these sources. As with other naturally-occurring monoisotopic elements (except Be), scandium contains an odd number of protons and an even number of neutrons. Scandium metal was first prepared by Fischer and coworkers1 in 1937 by electrolysis of scandium chloride in a molten eutectic mixture of lithium and potassium chlorides, using molten zinc as a cathode and collector of the scandium metal produced. The zinc was removed from the Zn-2 pct Sc alloy by vacuum distillation, leaving a product reported to be 94 to 98 pct Sc, with the main impurities being iron and silicon. They reported a melting point of 1400° C for this material. Scandium has also been prepared by the reduction of scandium chloride with potassium metal in a glass apparatus by Bommer and Hohmann in 1941,' resulting in a mixture of metal and potassium chloride; these workers did not isolate the metal proper, but the X-ray diffraction of the slag-metal mixture showed it to be hexagonal with a = 3.30A, c = 5.45A. petru3, 4 and coworkers have recently reported the preparation of the metal in a compact form by the reduction of either ScF3 or ScC13 with calcium metal and subsequent distillation of the product. This process probably yielded a metal of high purity, but they list no chemical analysis nor do they list any of the properties of their product. Previous related work in this Laboratory has been concerned with the production of yttrium and the rare-earth metals and the determination of their physical properties. Because of its similarity to these metals, scandium is being included in this study. PREPARATION OF SCANDIUM METAL The preparation of yttrium and the rare-earth metals may be accomplished by reduction of their fluorides with calcium metal in tantalum crucibles.5 This process leads to the introduction of tantalum (up to 0.5 pct) as an impurity in the higher melting rare earths, but since the tantalum occurs as dendrites, uncombined with the rare-earth metals, its presence is not objectionable in some cases. The preparation of scandium metal in this manner, however, was found to yield a product containing 2 to 5 pct Ta. To obtain a purer product, the following two methods were developed for the reduction of scandium fluoride with calcium metal: i) a low-temperature process utilizing zinc to form a low

Jan 1, 1961

By James Howe

EVERY engineer and user of wire rope is desirous of information that will enable him to determine whether the performance of any particular piece of rope is satisfactory, and what conditions can be changed so as to increase the life of a rope. In most cases, it is far from easy to analyze the conditions of service and tell which is the greatest factor in determining the life of wire rope. If we start on a layout for an entirely new rope system, the task of making conditions satisfactory is simplified so far as the engineering details are concerned; but if the plant requiring wire rope is in operation, any change is likely to involve the expenditure of consider-, able money to replace and change over machinery that must be kept in constant operation, because a large monetary loss will result from a shutdown for even a few days. Often wire rope is kept operating under bad conditions, as the user thinks that it is cheaper and quicker to replace the rope than to make alterations in the hoisting machinery. A typical case is a metal mine operating in what is now almost the center of a large mining city, where it owns a few acres of mineral rights. It was expected that the shaft would go to a depth of 1000 ft. (305 m.), so a moderate sized rope, about 1 ¼ in. (31.7 mm.), was used on a 6-ft. drum with a 7-ft. head-frame sheave and rather short lead from drum to head sheave. This mine has gone deeper each year until, it is now 2500 ft. deep and the rope speed has been increased from 1500 ft. per min. to over 3000 ft. The original rope just filled the drum in one layer, now it overwinds three layers. The original ropes were probably 6 X 19 crucible steel and lasted from 12 to 18 mo.; now, the highest grade plow steel is used, yet the average service is only about 6 mo. The cause is not hard to find. If the engineers had known at the outset what would be done with this hoist, the design would have been very different. Conditions at this mine, from a wire rope standpoint, have gradually become worse and it is difficult to see how rope service on this hoist can be com-pared with the service of previous years with any fairness to the wire-

Jan 2, 1922

By E. A. Gulbransen, K. F. Andrew

The vacuum-microbalance method was used to study the oxidation behavior of Zircaloy-2 and -3A over the temperature range of 300 to 850°C and at 0.1 atm pressure. The results fit in well with the authors' earlier studies on zirconium. Tin was found to increase the rate of oxidation and also the temperature at which the metal burns. Both the cubic-rate law and the parabolic-rate law gave imperfect fits to the rate data. Since the parabolic-rate law has been derived from accepted physical principles, this rate law was used to interpret the rate data. A heat of activation of 28,600 cal per mole was calculated. The transition phenomenon previously observed in hot-water and steam-corrosion processes was studied systematically for oxygen atmospheres. Observations on the rate of oxidation, color and properties of the oxide films show that the transition phenomenon was associated with a failure in the adherence of the oxide to the alloy. ZIRCALOY-2 and -3A have found important uses in the field of reactor metals due to their low neutron adsorption, good strength and good resistance to corrosion. One feature of the corrosion reaction in steam or hot water is the sharp transition in the rate of corrosion to a higher value after a certain amount of reaction has occurred. This paper presents a study of the reaction of Zircaloy-2 and -3A with oxygen including a study of the transition phenomenon which has been found to occur also in oxygen atmospheres. A comparison will be made between the oxidation behavior of these alloys and the pure metal. It was hoped that a study of the details of the oxygen reaction would lead to a better understanding of the reactions occurring in hot-water and steam atmospheres. Literature Kinetics-—The reaction of Zircaloy-2 and -3A with hot-water and steam atmospheres has been studied by Thomas.' Goldman and Thomas,' Thomas and Forscher," and Thomas and Kass.' Empirical equations for the kinetics of the reaction have been given by Thomas and Forscher." The change from the initial slow rate of reaction to the final rapid rate of reaction has been termed transition with the post-transition corrosion kinetics following a simple linear equation in time. The corrosion behavior in high-temperature steam was similar in many features to the corrosion in high-temperature water. Goldman and Thomas' and Pray and Peoples' have shown that the addition of tin, while increasing the rate of corrosion, counteracts the deleterious effect of nitrogen. The beneficial effect of iron, nickel and chromium was to improve the adhesion of the oxide to the metal as well as to counteract the deleterious effect of nitrogen. Mallet and Albrecht" have studied the oxidation of two zirconium-tin alloys. The cubic-rate law was found to fit the oxidation data for the 1.5 pct tin alloy while the parabolic-rate law was found to fit the data for the 2.5 pct alloy. Kendall' in a recent paper has studied the oxidation of Zircaloy-2 containing 1.5 pct tin in air atmospheres. Transition Phenomenon—In steam atmospheres Thomas' has observed fora 1.8 pct tin alloy containing small amounts of iron, nickel and chromium that transition to a more rapid rate of corrosion at 400°C

Jan 1, 1959

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

By A. W. Fahrenwald

CELL depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence-i.e., the depth in the pulp at which the impeller is required to produce aeration. THE FLOTATION MACHINE A COMPRESSOR A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure[t] (14.7 lb. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 lb. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 lb. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 [-] 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 [=] 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the finer, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. THE FLOTATION MACHINE AS A PUMP Since, in impeller machines that rely upon their own operation to produce aeration, pulp passes through the im-

Jan 1, 1946

By Eckhard Nembach

The phase diagram of the system Pb-In has been investigated between -27° and + 40°C, using nzainly X-ray dijfraction. In accordance with t her mo dynamic measurements by Heumann and Predel, a segregation occurs at low temperatures, though not in the form of a nziscibility gap. THE phase diagram of the system Pb-In has been the subject of extensive investigations,1&apos;1 but recently Heumann and prede13 concluded from their thermodynamic data that a new feature should occur below room temperature. These authors observed that the maximum values for the enthalpy and entropy of mixing, which occurred at a composition of 50 at. pct Pb, were +400 and —1.7 cal per g-atom deg, respectively. From this the authors estimated that a miscibility gap should occur below 30°C, centered at 50 at. pct Pb. Resistivity measurements seemed to support this view. These authors proposed the phase diagram outlined in Fig. 1. Three phases exist at 30°C: the tetragonal indium phase with c/a > 1, the tetragonal intermediate phase a, with c/a < 1, and the fcc lead phase. During an investigation of the superconducting properties of Pb-In alloys. it has been observed4 that aging a specimen with 50 at. pct Pb for 14 days at -18°C decreased the superconducting transition temperature about 0.13"K and tripled the transition width. In this paper, the results of an investigation of the Pb-In phase diagram in the temperature range from — 2T to +40°C are reported. Superconductivity and X-ray methods have been used. 1) SPECIMEN PREPARATION The materials were provided by the American Smelting and Refining Co. According to the manufacturer their purity was 99.999 pct. The weighed amounts of the constituents were sealed in quartz tubes under an atmosphere of 10 torr helium, mixed for 24 hr in a rocking furnace at 380°C, quenched in ice water, and homogenized at 20" to 30°C below the solidus line, established by Heumann and Predel. The annealing times were 144 hr for specimens containing Less than 30 at. pct Pb and 36 hr for the remainder. 2) SUPERCONDUCTIVITY EXPERIMENTS The specimens were quenched from the homogeniza-tion treatment into ice water and their superconducting transition temperatures T, measured. The procedure used has been described in Ref. 4. The transition was detected by the change of the mutual induc- tance of two coaxial coils containing the sample. T, was defined as the temperature at which 50 pct of the total change in inductance had occurred. The repro-ducibility with which T, could be measured was i0.002"K. Then the specimens with lead contents between 38 and 75 at. pct were aged for 7 days at temperatures between -30" and 40°C. If this treatment caused T, to change by more than 0.005"K or the width of the transition to increase by more than 0.002"K, it was concluded that the specimen had undergone a phase change and no longer consisted only of the fcc lead phase: as it did immediately after homogenizing. The result is shown in Fig. 2. From this one can estimate at what temperatures and concentrations phase changes occur. The X-ray measurements were based on these preliminary results. 3) X-RAY EXPERIMENTS Because of the softness of the material, relatively coarse powders. 75 p, had to be used, which were filed in a helium atmosphere from homogenized specimens. The powders were annealed at least 30 min at temperatures between 120" and 16OJC, depending on their concentration, and quenched in ice water. Then their X-ray patterns were taken at -178°C with a Picker diffractometer, model 3488K, and a cold stage. on which the specimen was in thermal contact with a liquid-nitrogen reservoir. In this way the following relation was established for the fcc lead phase: a = 4.697 + 0.00247C for 40 5 C 5 75 11 where n is the lattice constant (A) and C is the at. pct of lead. The coarseness of the powder made it impossible to use lines with 0 > 75 deg; therefore n was averaged from lines with 45 deg 5 0 5 75 deg. The results were reproducible to within i0.05 pct. Relation [I] is very similar to the one found by Heumann and Predel at room temperature. Following this, homogenized specimens with compositions between 15 and 56 at. pct Pb were aged for at least 10 days at temperatures between -27" and

Jan 1, 1970

By J. R. Long, T. R. Graham, R. G. Feustel, R. S. Dean

THE comprehensive study of the copper-manganese-zinc alloy system in the Bureau of Mines Laboratories has so far been principally concerned with alloys that lie within the alpha solid solution field of the system. Two regions, one centering about 65 per cent copper, 10 manganese and 25 zinc, and the other centering about 70 per cent copper, 20 manganese, 10 zinc, have been carefully examined.1,2 These have indicated that when the alloys are made with electrolytic manganese considerable amounts may be readily introduced and that the strength and hardness are increased without excessive losses in ductility. In the course of the work of establishing the limits of the alpha solid solution range,3 enough of certain of the alloys was prepared to permit determination of their physical properties at a future date. The 60 per cent copper alloys concerned here are part of that series. They cross through the alpha field and into the adjacent alpha plus beta and alpha plus X fields, and are of interest because they offer some information on the effects of manganese on alloys lying in these fields. COMPOSITION AND FABRICATION OF ALLOYS The chemical composition of the alloys involved is given in Table I. They were intended to contain 60 per cent copper with manganese increasing from 5 to 25 per cent in 5 per cent steps and zinc decreasing [ ] from 35 to 15 per cent. The analyses are so close to the intended composition that the alloys will be referred to hereafter by their nominal compositions. They were finished into sheet by cold-rolling and intermediate annealing procedures calculated to produce sheet 1/16 in. thick, cold-reduced by 20, 40, 60, and 80 per cent in thickness. Physical properties were determined on standard flat tensile specimens with 4-in. gauge length, although the test gauge section used was 2 in. The properties were obtained on cold-worked material and on material annealed at temperatures ranging from l00° to 1500°F. after 60 per cent cold reduction. Since an annealing temperature of 1200°F.

Jan 1, 1946

By H. C. Fiedler

The solubility of sulfur in Si-Fe was determined by the metallographic examination of heat-treated and quenched samples. In the absence of manganese, the solubility in 3.1 pct Si-Fe was found to be about 0.010 pct at 1000o C, 0.015 pct at 11000C, and 0.020 pct at 1150°C, which is substatntially less than hitherto reported. Increasing the silicon content was found to decrease the solubility of sulfur, which is consistent with the increase in the activity coefficient of sulfur with increasing silicon content that has been reported for Fe-Si alloys. Manganese additions were studied in alloys containing 3.1 pct Si and between 0.013 and 0.015 pct S. At low manganese levels the solubility product of manganese sulfide was found to be lower than previously reported. THE solubility of sulfur in pure polycrystalline iron has been reported by Rosenquist and Dunicz1 and by Turkdogan et al.2 Samples were equilibrated in atmospheres containing different ratios of H2S/H2. Both groups of investigators found a solubility limit in y iron of 0.013 pct at 1000oC and 0.031 pct at 1200°C. In addition, Rosenquist and Dunicz1 found a solubility limit in a iron of 0.020 pct at 900°C. Ainslie, Hoffman, and seybolt3 found significantly higher sulfur contents in polycrystalline iron samples than in single-crystal samples after heating at 890°C in a sealed tube containing a mixture of powdered iron and FeS made with s35. Whereas the single crystals contained 0.013 and 0.016 pct S (± 0.005 pct), the polycrystalline samples contained between 0.016 and 0.026 pct S. Autoradiographs suggested that the excess sulfur in the polycrystalline samples was due to the segregation of sulfur in solution at grain boundaries. Ainslie and seybolt4 have reported on the solubility of sulfur in 3 pct Si-Fe. Their samples were sealed in capsules containing hydrogen and sufficient sulfur as cobalt sulfide to saturate the sample. After heat treating, the sulfur-rich phase on the surface was removed by abrading, and the sulfur content of the sample was taken as the equilibrium value for that temperature. Before the equilibrating heat treatment, the samples were heated to 1300°C to coarsen the grains. The resulting grain size, which was about 3/18 in. in diam, was considered sufficiently large to preclude a sensible increase in sulfur solubility due to grain boundary segregation. They reported the solubility to be 0.029 pct at 900oC, 0.063 pct at 1000oC, 0.076 pct at 1100°C, 0.122 pct at 1200°C, and 0.098 pct at 1300°C.

Jan 1, 1968

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

By Robert D. Gunn, John E. Boysen, Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA&apos;s Laramie Energy Research Center at a site near Hanna, Wyo., was completed on Jul. 30, 1976. During the experiment production reached 0.32 blm3/d (12 M cu ft/d) of 6.9 w/m3 gas (175 Btu per cu ft). Approximately 6100 tonnes (6700 tons) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, coal gas thermal efficiencies of 76 to 89%, and overall process efficiencies of 65 to 74% were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-74.

Jan 1, 1978

By Robert Linton

SPECIFICATIONS for clays serving raw materials in the ceramic industry usually contain the following items: (1) Chemical analysis, sometimes with mineralogical structure determined by microscopic investigation. (2) Maturing temperature and firing range, usually expressed in terms of pyrometric cone equivalent. (3) Shrinkage (drying and firing shrinkage separately). (4) Degree of plasticity. (5) Color after firing. Clays may be classified, according to the purpose of the classification, in several different ways, based on (1) Geological occurrence-transported, altered An place, indurated (shales). (2) Physical properties-plastic (bonding clays, ball clays) and nonplastic (flint clays, kaolins or china clays, bone clays). (3) Color. (4) Use. A common classification of clays for commercial designation, and one fol-

Jan 1, 1936

By E. D. Hummer

During the planning of the fine coal cleaning addition at the Gary, W. Va., Coal Preparation Plant of United States Steel Corp. careful consideration was directed toward the problem of minus 48 mesh refuse disposal. The plant flow sheet included wet screening the raw coal at ¼ in., pumping the minus ¼ in. raw coal to bowl desiltors for desliming, and then cleaning the deslimed raw coal on tables. The material to be removed from the circuit as minus 48 mesh refuse consisted of the minus 100 mesh desiltor overflow thickened in two 120 ft diam thickeners and minus 1 mm screened from the table refuse. Later a flotation plant was added to recover coal from the desiltor overflow, and a classifier replaced the screens to make a sharper size separation of the table refuse at 48 mesh. Today the minus 48 mesh refuse at Gary consists of thickened flotation tailing and thickened spiral classifier overflow. The transportation of large quantities of fine, wet refuse filter cake mixed with jig and table refuse over existing conveying equipment would have been neither dependable nor economical. Filtration was therefore impractical, and disposal of the fine materials was a problem. The decision was to pump the material to storage ponds.

Jan 3, 1965

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during January: A. Neustaedter, Jersey City, N. J. William Jones, Kent, England. A. J. Sweetser, Boston, Mass. Percy E. Barbour, Candor, N. C. Algernon Del Mar, Los Angeles, Cal. Herbert S. Kohlberg, El Paso, Texas. W. B. Cogswell, Syracuse, N. Y. I. N. Knapp, Ardmore, Pa. R. E. Chambers, New Glasgow, N. S.

Jan 2, 1914

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,&apos; where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964

Research and Development, once considered a luxury item only for well-heeled companies, has in the last two decades come into its own as a vital contributor to the fortunes of electronic, automotive, chemical and aerospace firms. In terms of money and talent poured into research, the mining industry is still far behind those industries. Although the U.S. Bureau of Mines, plus various mining and manufacturing firms and universities have made notable contributions to mining technology, the historical pattern of mining R&D shows a heavy reliance on the results of research in other industries. It is difficult to tell whether this pattern will change significantly in the future, but there is evidence of a growing awareness by mining officials that greater R&D efforts are going to be required not only to meet the nebulous demands of tomorrow&apos;s world but to meet the ever-present, mounting pressures being generated by "intra-metals" and "inter-materials" competition.

Jan 1, 1968