Search Documents

By D. R. Parrish, W. E. Lamoreaux, W. W. Owens

Several methods are now being used by the industry for determining the gas-oil flow characteristics of reservoir rock samples. Most of the laboratory experirnerltal rlzethods can be classified either as steady-state, unsteady-state, or Hassler-type tests. Although the validity of the results obtained by any specific method is not questiorzed, in general, the complexity of these methods leaves much to be desired. This investigation dealt primarily with the development of a simplified unsteady-state (gas drive) laboratory test method for measuring kg/ko re1ationships of small core samples. A procedure for selecting uniform and representative sandstone rock samples was developetl since it was observed that the reliability of the test resu1ts was dependent upon having a sample which was uniform in porosity and permeability. The importance of factors known to influence the results of this type test, such as oil viscosity, gas expansion, and pressure differential were eva/uated. The method of calculating the test results was found to give valid data over a wide range of gas expansion. The limits of pressure differential and oil viscosity which would insure reliable results were defined. In cornparisorz with other presently used testing methods, the gar drive method requires considerably less apparatus, is less time consuming, and is more readily adaptable to a routine type core test. INTRODUCTION The detcrmination of the gas-oil flow characteristics of reservoir rocks has been given concentrated study by the oil industry for the past decade. Both analytical and experimental methods have been considered. The analytical methods have generally relied on a simplified characterization of porous materials in order that the fundamental laws of fluid flow and capillarity could be utilized. More direct experimental methods have been proposed by numerous production research laboratories with the primary goal being a simple and inexpensive, yet reliable method for measuring the gas-oil flow characteristics of reservoir rock samples. The experimental methods which have been reported in the literature generally can be grouped into one of the following classifications: 1. Steady state1,2,3,4 in which a fixed ratio of flowing fluids is forced through the test sample until equilibrium conditions of saturation and pressure gradient are established. 2. Hassler or stationary liquid method5,6,7 in which a uniform liquid saturation is attained, usually through capillary desaturation, then gas or oil is flowed through the sample at a pressure drop insufficient to disturb the pre-established saturation. :. Non-steady state method1,8,9,10 In which only the gas phase is injected into the sample, causing displacement of the oil phase and resulting in a system of continually changing average saturation and saturation gradient. The steady-state and Hassler methods have been most popular because, no doubt, of the simplicity of the actual relative permeability calculations. The problems involved in these methods were limited to apparatus design and measurement techniques. In the steady-state method, for instance, a constant flowing fluid ratio is established which, at equilibrium, results in an essentially uniform saturation over the entire length of the test sample. Therefore, the basic flow characteristics could be obtained by correlating the average saturation of the test sample with the kg/ko determined at various flowing gas-oil ratios.

Jan 1, 1957

By M. H. Sommer

MANY attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals com-monly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compression or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and

Jan 1, 1934

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By Takashi Katsura, Avnulf Muan

Equilibrium relations in the system FeO-Fe2O3 Cr2O3 have been determined at 1300°C at oxygen pressures ranging from that of air (0.21 atm) to 1.5 x 10-11 atm. The following oxide phases have stable equilibrium existence under these conditions : a sesquioxide solid solution with corundum-type structure (approximate composition Fe2O3-Cr2O3); a ternary solid solution with spinel-type structure (approximate composition FeO Fe2O3-FeO Cr2O3) and a ternary wüstite solid solution with periclase-type structure and compositions approaching FeO. The metal phase occurring in equilibrium with oxide phase(s) at the lowest oxygen pressures used in the present investigation is almost pure iron. The extent of solid-solution areas and the location of oxygen isobars have been determined. ThE system Fe-Cr-O has attracted a great deal of interest among metallurgists as well as ceramists and geochemists. Metallurgists have studied the system because of its importance in deoxidation equilibria, ceramists because of its importance in basic brick technology, and geochemists because of its importance for an understanding of natural chromite deposits. Chen and chipman1 investigated the Cr-O equilibrium in liquid iron at 1595°C in atmospheres of known oxygen pressures (controlled H2O/H2 ratios). The main purpose of their work was to determine the stability range of the iron-chromite phase. Hilty et al.2 studied oxide phases in equilibrium with liquid Fe-Cr alloys at 1550°, 1600°, and 1650°C. They reported the existence of two previously unknown oxide phases, one a distorted spinel with composition intermediate between FeO Cr203 and Cr3O4, the other Cr3O4 with tetragonal structure. They also sketched diagrams showing the inferred liqui-dus surface and the inferred 1600°C isothermal section for the system Fe-Cr-O. Koch et al3 studied oxide inclusions in Fe-Cr alloys and also observed the distorted spinel phase reported by Hilty et al. Richards and white4 as well as Woodhouse and White5 investigated spinel-sesquioxide equilibria in the system Fe-Cr-O in air in the temperature range of 1420" to 1650°C, and Muan and Somiya6 delineated approximate phase relations in the system in air from 1400" to 2050°C. The present study was carried out at a constant temperature of 1300° C and at oxygen pressures ranging from 0.21 atm (air) to 1.5 x 10-11 atm. The chosen temperature is high enough to permit equilibrium to be attained within a reasonable period of time within most composition areas of the system, and still low enough to permit use of experimental methods which give highly accurate and reliable results. These methods are described in detail in the following. I) EXPERIMENTAL METHODS 1) General Procedures. Two different experimental methods were used in the present investigation: quenching and thermogravimetry. In the quenching method, oxide samples were heated at chosen temperature and chosen oxygen pressure until equilibrium was attained among gas and condensed phases. The samples were then quenched rapidly to room temperature and the phases present determined by X-ray and microscopic examination. Total compositions were determined by chemical analysis after quenching. In the thermogravimetric method, pellets of oxide mixtures were suspended by a thin platinum wire from one beam of an analytical balance, and the weight changes were recorded as a function of oxygen pressure at constant temperature. The data thus obtained were used to locate oxygen isobars. The courses of the latter curves reflect changes in phase assemblages and serve to supplement the observations made by the quenching technique. 2) Materials. Analytical-grade Fe2O3 and Cr2O3 were used as starting materials. Each oxide was first heated separately in air at 1000°C for several hours. Mixtures of desired ratios of the two oxides were then prepared. Each mixture was finely ground and mixed, and heated at 1250" to 1300°C in air for 2 hr, ground and mixed again and heated at the same temperature for 5 to 24 hr, depending on the Cr2O3 content of the mixture. A homogeneous sesquioxide solid solution between the two end members resulted from this treatment. A Part of some of the sesquioxide samples thus prepared was heated for 2 to 3 hr at 1300°C and oxygen pressures of 10-7 or 1.5 x 10-11 atm. Reduced samples (either iron chromite

Jan 1, 1964

HENRY A. VEZIN, Denver, Colo. (communication to the Secretary, February, 1897): I have read Mr. Austin's paper with considerable interest, more especially as the designing and study of such works have been an attractive occupation for me during the last twenty-five years. Mr. Austin says that a " plant on a terraced site has generally been considered the most advantageous," and also that " many advocate a level site," while he himself " is disposed to advocate a modification of the latter plan, utilizing an extended surface with a moderate slope."* Among the advocates of the terraced sites as against level ones, I do not recollect ever meeting a metallurgist who had even made an attempt to plan his works for level ground, or who had, in a lucid interval, figured how much he gained or lost by one or the other method. The average metallurgist starts with the assumption that it is rational to conduct his material down hill because its movement is aided by gravity, while to elevate ore or furnace-material by machinery he vaguely believes to be not alone wrong in principle, but also unnecessarily expensive. Let us look into the expense of elevating and see whether it really is prohibitory of the successful operation of smeltingworks on a level site. Hoisting or elevating material in the

Jan 1, 1897

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-I have the honor to present the following, report for the calendar year 1920. The activities which seem to call for special comment are: THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments. It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year. Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters. The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published. The Bound Volumes, as usual, contain all the papers in full and discussions thereof. FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent. greater than the members paid when the Institute was founded forty-nine years ago. This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies. The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of the national engineering societies has rendered the situation more difficult for us. MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St. Louis, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine.

Jan 1, 1925

Discussion o f Papers. Meetings of the Institute offer opportunity for social acquaintance and exchange of ideas, for the--presentation of papers, and-for discussions. thereon ; also incidentally for viewing under especially favorable conditions mining operations and industrial establishments, and for hospitalities which demonstrate the brotherhood clue to kindred interests. Placing sociability prominent is not to be assumed as relegating other features of meetings to subordinate positions; but during about 40 years of membership in the Institute, the value of acquaintances formed (often ripening into close friendship), and the interchange of data, have frequently demonstrated that the social feature of meetings is of great and lasting value to the membership. Of a roll embracing 4,011 members, resident in all parts of our country, and scattered in various portions of the world, only a small fraction are able to attend meetings, even if the localities selected are alternately widely separated. Hence, the return which most members receive for their annual assessment of dues is limited to the publications issued, and the credit of being recognized as a. member of a great and worthy organization. The greater the value of the contents of our publication, the fuller the return which goes to members. While the Institute disavows responsibility for views or statements made ill papers which appear in its Transactions, the fact that these contributions, after passing proper censorship, are accepted by the Institute and spread before the world may properly be received by the writers as endorsements of their (the writers') ability to present a specific technical or industrial proposition worthy of being carefully read. But the mere presentation and publication of contributed papers falls short of fulfilling one important feature of our meetings. If the purpose is confined to having the writers' views, discoveries, theories, or methods published, this can be obtained through the technical or trade journals and magazines. The true value of a paper presented at a meeting of the Institute may often be gauged by the discussion which it encourages, although there are contributions of decided value which do not especially invite discussion. However, most Of the papers offered contain statements apt to encourage criticism or elaboration by others whose experience or knowledge, or both, assist in combating or endorsing statements made.

Jan 7, 1913

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By Michael A. Arkoosh, E. A. Peretti

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970

By Dubois Eastman

BEHIND the contrasting liquid-fuel technologies of Germany and the United States lie the basic differences of scarcity and abundance. The chemists and engineers of each nation have developed processes that accommodate available raw materials. In the United States, processing is based on an abundant supply of petroleum, which is refined into a variety of fuels and lubricants. Germany has little indigenous petroleum but has a readily available supply of coal that can be converted into liquid fuels and lubricants. As a result, in Germany several basic processes have been developed for the conversion of coal into synthesis gas (carbon monoxide and hydrogen). In turn, this gas is processed into products. As a normal function of its researches into petroleum processing, the petroleum industry in the United States has made careful studies of various conversion and synthesis techniques. A number of oil companies are carrying out independent development programs with the aim of synthesizing hydro- carbon products that can be marketed at a price that will compete with the price of refined petroleum products. American oil companies hope to perfect synthesis processes that will directly benefit the consumer. A good example of progress in these terms is the synthesis plant at Brownsville, Texas, which is based on the conversion of natural gas to synthetic fuels and other valuable products. When this plant is operated at near capacity, it is expected that the products will be able to compete favorably for the consumer dollar. The complete gasification of coal is a technique well rooted in history. As a controlled process on a small scale, it goes back centuries. As a practical technique on a commercial scale, it dates back to 1839, when "producer gas" appeared in Germany for limited industrial use. By 1873, "water gas," or "city gas" as it is sometimes called, was being manufactured commercially in the United States for use in heaters and stoves. The water-gas process was the cornerstone for modern synthesis. To older methods that were concerned only with carbon and oxygen reactions, it added hydrogen by means of steam. Thus far the goal of conversion was to produce gas for heating, lighting, industrial use, and cooking. The long step forward to synthesis was made in 1927, when Germany started to make gasoline from coal by means of the revolutionary Bergius hydrogenation process. A year earIier, Franz Fischer and Hans Tropsch had announced their process, which finally reached the

Jan 1, 1953

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By Henry R. Joesting

DURING the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,1,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. PROBLEMS One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3,4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. INSTRUMENTS AND METHODS Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey.5 For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1941

By Edward Norton

THE -salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Ouachita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By B. L. Averbach, M. Cohen, G. P. Conard

IT has been frequently observed that, when metal crystals are bent and annealed or when they are bent at elevated temperatures, the asterism of the Laue spots is split discontinuously into tiny intensity maxima. This finding indicates that segmented crystallites or subgrains are produced, which are relatively undistorted within themselves but which differ slightly in orientation from their neighbors. The following viewpoints have been put forward concerning the nature of this segmentation process: 1—Crussard' has described the phenomenon as "re-crystallization in situ." According to this mechanism, the deformed lattice recrystallizes on heating into an aggregate of comparatively strain-free subgrains separated from one another by low-angle boundaries and having nearly the same orientation as the original crystal. This process differs from the classical type of recrystallization in that the latter involves the formation of grains having quite different orientations from that of the mother crystal. 2—A similar but more detailed picture has been advanced by Cahn' who adopted the term "polygonization." In this interpretation, the plastic bending of lattice planes results in an excess of dislocations of one sign, but at suitable temperatures these dislocations migrate along slip planes and collect in localized regions to form an array of low-angle boundaries. Concurrently, the lattice segments between the boundaries lose their curvature and elastic strain. 3—The "cell formation" concept of Wood and co-workers: unlike the two hypotheses cited, postulates that the segmentation of the lattice is basically a mode of deformation and is not an annealing phenomenon. Cell formation appears to compete more effectively with respect to the normal slip process as the deformation temperature is increased and as the strain rate is decreased. The present work was performed on 3.2 mm diameter 99.99' pct Zn single crystals, grown from the melt in a gradient furnace. The major impurity was 0.003 pct Fe. The crystal orientations ranged from those with basal plane parallel to the rod axis to those with the basal plane almost perpendicular to the rod axis. The specimens were bent on templates to effective radii varying from 14.2 to 1.3 cm at the temperatures from —196" to 100°C. In each case, the axis of bending was parallel to the basal plane. Subsequent annealing was carried out at temperatures from —196" to 400°C. Back-reflection Laue pictures were taken on the convex surface of the bent specimens, before and after annealing. This procedure was found to yield better resolution of the detail in the diffraction spots than did the previously used Laue transmission technique. Some X-ray pictures of rods bent at —196" and —78°C were taken at these respective temperatures without intermediate warming to room temperature. In addition, bent crystals were acid cut" parallel to the basal plane, and double-crystal spectrometer rocking-curves were obtained from the etched (0001) face before and after increment an-

Jan 1, 1954

By F. Milton Lewis, Edward S. Frohling

The information which is required for' a preliminary feasibility study and the additional information which is required for the final feasibility study on a new mineral deposit are discussed. The preliminary feasibility study is made from very little information and at a minimum cost to the owner. However, the outline for the preliminary report is similar to the one used in the final report. In this manuscript, it is assumed that the results from the preliminary study are favorable and the owner authorizes a final feasibility study by an outside engineering company. The type of organization for completing this final feasibility study is described. The final reports includes all information and data relative to this new mineral deposit. This information is presented so that it may be understood by financial people as well as by technical people.

Jan 1, 1978

By John H. Hollomon

IN a recent paper,1 a very early suggestion by Ludwik2 concerning the nature of the mechanical behavior of metals has been reexamined and extended. In essence it was [ ] suggested that there exists, at least under certain conditions, a mechanical equation of state; that the stress required for flow depends upon the instantaneous values of the strain, strain rate, and temperature, and not upon their past values. It is proposed that under these circumstances the stress does not depend upon past history of these variables, but is like the temperature of a gas that depends only upon the I instantaneous values of the pressure and volume. This notion has not been applied to present day studies of metals, though it is especially applicable to the study of creep. It is the purpose of this paper to analyze the significance and possible range [ ] of applicability of this idea and to deter- mine how it influences the accepted ideas concerning creep. STRESS-STRAIN RELATIONS It is well known that the stress-strain curves of metals are influenced by both strain rate and temperature. For a fixed strain rate and temperature there is associated with each metal a stress-strain curve. If either the strain rate or temperature is changed a new stress-strain curve will be characteristic (Fig. I). A much more general relation between the effects of the sevariables is possible, however. Consider the stress-strain curves of Fig. I determined at

Jan 1, 1946

ALABAMA Aldrich.-Lloyd, T. W. Anniston.-Carrington, F. G. Klugh, B. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson V. Salmon, h. S. Stuart, Q. W. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Armstrong. W. D. Ball, E. M. Bonnyman, J. Bush, M. W. Carter, E. Crawford, G. G. Davis, C. B. Dryer. T. B.

Jan 1, 1923

By James Aston

A PROPER consideration of this subject is not confined to the technical channels of production and metallurgy. It concerns an industry, and should cover economic aspects which are of material importance in any program of development. The discussion may logically be treated under three subdivisions, as follows: (1) manufacture, (2) characteristics related to quality of material; (3) adaptability and exploitation of product. MANUFACTURE OF WROUGHT IRON The manufacture of wrought iron is the most ancient art of the ferrous metal industry. The eighty years or less of existence of processes identi-fied with our modern "Age of Steel" is a relatively brief interval com-pared with the several thousand years associated with the production of wrought iron by man. From the primitive early methods of production, manufacture for many centuries followed the line of direct reduction. There were developments as experience was gained through the years; but man's needs for a strong, ductile, forgeable product were met by reducing the ore to metallic iron in a single-stage operation. Following the development several centuries ago of what has become our modern blast-furnace operation, manufacture of wrought iron was gradually transformed into a two-stage method of first producing cast iron and then refining this to the desired degree of forgeability; the fore-runner in principle of today's scheme of manufacture of steel. The product retained the essential characteristics of highly refined base metal with iron-silicate slag incorporation, which were associated with the material resulting from direct reduction methods. Cort's invention of the puddling process in 1784 is a landmark in wrought-iron manufacture. It consisted essentially in adapting a coal-fired reverberatory furnace to the refining operation; thus lifting the industry out of the slough of

Jan 1, 1935