Search Documents

By A. Andreas

New Mexico retained its position in 1938 as the sixth largest oil-producing state, with a total production of 35,510,176 bbl. This was 2,875,598 bbl. less than the 1937 production of 38,485,774 bbl., or a decrease of 0.077 per cent, which was caused by the lack of pipe-line facilities and storage at the pipe-line terminals. The production for Lea County (excluding Maljamar) was 32,926,788 bbl.; for Eddy County (including Maljamar) was 2,225,411 bbl.; and for northwestern New Mexico (San Juan and McKinley Counties), 357,977 bbl. The average daily nonmarginal well allowable for Lea County on Jan. 1, 1938, was 65 bbl. At the close of the year it was 49 bbl. The average daily pipe-line runs for domestic consumption were less than the state allowables recommended by the United States Bureau of Mines. There was a demand for Artesia crude for foreign export, which if included in the daily production for New Mexico would be slightly in excess of the daily production recommended for New Mexico by the Bureau of Mines. The daily average production for the year was 97,329 barrels. There were 622 completions in the state, of which 520 were oil wells; 16 hydrocarbon gas wells; 5 carbon dioxide gas wells, and 81 dry holes. Of the dry holes 38 were in or near-by proven fields and the remainder, 43, were wildcats. Five new fields were discovered in New Mexico during 1938, three in Lea County and two in Eddy County. Southeastern New Mexico Lea County.—The Monumcnt field was the largest producing field in Lea County, with 9,440,334 bbl., and was closely followed by the Eunice field with 8,872,335 bbl. The Hobbs field was third with 5,010,414 bbl. The greatest activity in Lea County was in the Vacuum pool, with 129 completions, of which 126 were oil wells and three were dry holes. The Texas Company completed its Corbin NO. 1 in the KW 1/4 SW1/4 sec. 10, T. 18 S., R. 33 E. in August. This well was drilled to a depth of 5118 ft. in a white sand, encountering salt water. It was plugged back to 4315 ft, and pumped 43 bbl. of 36" gravity oil in 12 hr. It was approximately 6 miles southwest of the closest production in the Vacuum

Jan 1, 1939

By T. A. Rickard

MILLING is one of the metallurgical arts whereby the extraction of the largest possible proportion of the value in an ore is effected at the least possible expense. Stamp-milling* is that particular process in which a heavy body of iron is caused to fall upon the ore so as to disintegrate it and thereby induce a separation between what is valuable and what is worthless. The latter is usually less in specific gravity, and is therefore, by the further aid of water, removed from the former, which is then collected by the use of mercury. Several similes have been employed to describe this process. The stamp has been likened to a hammer of which the stem is the handle and the die the anvil. The ore upon which the stamp falls has been compared to a nut awaiting the descent of the hammer whose blow is to separate the valueless shell, the quartz, from the valuable kernel, the gold. When we begin to pursue our inquiries, however, we find that the analogy is just sufficiently true to emphasize the departures from it. The hammer falls, the anvil is fixed; so with the stamps and the mortar. The anvil is made of softer metal than the hammer; so also the die is often, and should be always, of steel or iron less hard and more tough than that of the shoe. The movement of the hammer and the drop of the stamp are both intermittent. In regard to their intermittent action, as in many other respects, stamp-mills arrange themselves under two types, which, though apparently contradictory, have both been evolved from a common original, and are united by a great variety of intermediate modifications. The slow speed and the high drop of the mills of Gilpin county Colorado, appear to have very little in common with the fast speed and short drop of those of the main gold belt of California; yet the practice of the one was largely derived from that of the other,

Jan 1, 1894

By R. V. Norris, E. W. Parker

Edward W. Parker,* Philadelphia, Pa.—At the New York meeting of the Institute a year ago, Mr. R. V. Norris presented a paper on anthracite mining costs, in which he gave the results of an intensive study of this subject by the Engineers' Committee of the United States Fuel Administration. Within the last 30 days, the Federal Trade Commission has issued an official report on the same subject, which covers a longer period of time and comprises statistics of realization values and margins that were pot comprehended in the paper by Mr. Norris. As, however, the data utilized by Mr. Norris formed also a part of the basis for the report of the Federal Trade Commission, a brief digest of the latter may not be out of place at this meeting. The report of the Federal Trade Commission covers primarily the two calendar years 1917 and 1918, divided into five periods which furnish opportunity for the study of how the influence of certain definite factors affected either the cost of production or the price, or both, during the 24 months. The first period, January to April, 1917, which may be considered the basic period, comprised the 4 months in 1917 during which the wage agreement of May, 1916, without modification, was in effect. During this period, the labor cost on fresh-mined coal is placed by the Commission's report at $1.79 per gross ton, the total cost at $2.66, the average realization at $3.29, and the "margin" (sales realization over total f.o.b. mine cost) at $0.63. The second period covers the four months from May 1 to August 31, during which time the first of the supplemental wage agreements (supplemental to the agreement of 1916) was in effect. It was also the period during which the summer discounts were in effect and when prices were practically fixed by a voluntary agreement between the operators and the Federal Trade Commission. It was, further, the period in which the 75 cents differential on prepared sizes permitted to the individual operators by the Federal Trade Commission began; at that time, also, on account of war conditions an unusually large quantity of steam sizes were marketed at exceptionally good prices. On account of the two latter conditions, not explained in the Commission's report, the "margin"1 on operating

Jan 1, 1920

By W. C. Hagel, H. J. Beattie

Phases present at 2200° and 1500°F (1204° and 816°C) were identified in sixty wrought developmental austenitic alloys possessing wide compositional variations. The bases were iron-, cobalt-, and nickel-rich as well as a base with equal parts of each. There are only two structure types previously not found in similar alloys, viz .-the Co3 W and the Fe3Al types. A molybdenum-rich monocarbide decorates dislocations with unusual clarity. Other results provide correlations between alloy composition and phas e precipitation. Grouping intermetal -lic phases into three general classes : I) geometrically close-packed, 2) topologically close-packed, and 3) bcc derivatives, the nickel base prefers the first, the iron base the second, and the cobalt base the third—each base tending to shun the other two classes. Thus, a crystal-chemistry effect previously noted by Laves and Wallbaum can he expanded for these Group VIII elemental bases. There appear to he no quaternary or higher -order structure types requiring more than three atomic species. AFTER studying aging reactions in many diverse commercial austenitic alloys1-4 as a function of detailed time-temperature variations in heat treatment, it became apparent that matrix composition influenced structure types and morphologies to a large extent. These tendencies were related4 to a crystal-chemistry effect uncovered by Laves and Wallbaum.5,6 We have now directed our efforts to exploration of the whole ternary field, covering the standard base elements—iron, cobalt. and nickel— with 10 to 20 pct Cr and moderate amounts, up to 10 pct, of the usual alloy additions. Solutioning and aging treatments were held constant with major emphasis on X-ray identification of microconstituents. The possible existence of exceptions to the Laves-Wallbaum effect, or any new phases, was sought. Phases appearing in austenitic alloys can be classified as geometrically close-packed (gcp), octahedral or nonoctahedral interstitial compounds, topologically close-packed (tcp), semicarbides, and bcc derivatives. Crystal structures of the first four classifications can be visualized as a dense packing of semirigid spheres of different sizes, while the bcc derivatives represent a less efficient packing of spheres. The Laves-Wallbaum effect involves the gcp and tcp phases. Gcp phases possess both tetrahedral and large octahedral interstices; examples are Ni3Ti(n), NiSAl(y'), Co3W(E), and other ordered AB3 compounds where B atoms are smaller than A. Their precipitation is primarily intragranular, presumably coherent with an austenitic matrix, and a chief source of strengthening. Most octahedral interstitial compounds (e.g., CbC, Tic, TiN, Mo2C) have a gcp lattice of large metal atoms which accommodate small carbon or nitrogen atoms in the octahedral interstices. The compound Ti2SC, previously designated Y phase or T phase, can, with some reservation due to its partial co-valency, be placed in this category.7 The nonoctahedral interstitials (e.g., M7C3, Fe3C) represent close-packings of spheres in structures that provide larger triangular-prism interstices for carbon, since the octahedral interstices formed by chromium and iron atoms are too small. Tcp phases possess only tetrahedral interstices; examples are Laves (Fe2Ti, Fe2Cb, Fe2W...AB2), p(Fe7MO6, Co7W8.... A8B7), and (FeCr, Co2Cr3)

Jan 1, 1965

By N. L. Svensson

The model developed by Tuylor for the calculation of Polycrystalline yield strength has been applied to the case of an aggregate hawing a preferred orientation. In general this procedure requires the specification of texture by means of weighting factors applied to specific orientations. The problem to which the model has been applied is that of the yield-strength aniso-tropy of cold-rolled aluminum whose rolling texture was described as a combination of (110)[112] and (311) [112] In this case yield-strength anisotropy is defined by the rutio of yield strength measured at an angle 8 to the rolling direction to that measured along the rolling direction. The method of calculation of yield-strength ratio as a function of ? is described and the results show good agreement with experimental values. The orthotropic yield criterion suggested by Hill has been applied to the results and the strain ratio R also calculated as a function of ?. This has been compared with calculations using the method suggested by Elias, Heyer, and Smith which does not exhibit suck good agreement with observation. one deficietlcy of the method presented is that the strain ratios used by are those applying to iso-Irobic materials. The method should therefore be reg-clrded only as a first abbroximation to the prediction of anisotropy. THE problem of calculating the stress-strain characteristics of polycrystalline aggregates from the properties of single crystals has attracted attention for a number of years. The most important contributions to this study have been those due to: Sachs,' Cox and sopwith,2 Taylor,3 Kochendorfer,4 Batdorf and Budiansky,5 Calnan and Clews,6 Bishop and Hill,7,8 Kocks,9 Budiansky, Hashin, and sanders, 10 Kroner,11 Cyzak, Bow, and payne, 12 Budiansky and Wu,13 and Lin.14 While the earlier work has been largely superseded, recent developments tend to support Taylor's solution" within the restriction imposed by his assumptions. The essential features of Taylor's approach were: 1) the material is rigid-plastic; 2) each grain experiences the same strain components as the aggregate as a whole (the problem was that of uniaxial deformation with principal strain components in the ratio 3) all regions of each grain deform uniformly; 4) work hardening occurs equally on all slip systems. While Bishop and Hill7 have generally validated this approach, there has been some criticism offered. Kocks? as pointed out that since multiple slip must occur the single-crystal data must be determined from orientations arranged such that polyslip takes place. Boas and Hargreaves,15 and others, have shown experimentally that the strain distribution within grains is not uniform, the strains in the vicinity of grain boundaries being less than those in the center of the grains. Both of these criticisms can be largely offset by the suitable choice of single-crystal critical shear stress. However, for the problem analyzed below, the critical shear stress is not directly used and, consequently, these criticisms lose their importance. The more recent contributions have attempted to obtain a more complete analysis by considering an elas-toplastic material and considering interactions between grains of differing orientations. Lin14 has considered the early stages of yielding for a polycrystalline aggregate having specific regions of defined slip plane orientations. On the other hand, Budiansky and Wu13 have allowed for these interactions for randomly disposed grain orientations and have calculated the polycrystalline stress-strain curves for crystals exhibiting either elastic-ideally plastic or kinematic hardening characteristics. This work has shown that yielding commences when the macroscopic stress is 2.2 times the critical shear stress for slip in a single crystal (7,). The yield stress-strain curve then rises becoming asymptotic to a value of 3.072 7,. This is close to the value obtained by Bishop and Hill (3.06) in their confirmation of Taylor's method. This, of course, is to be expected since, at large strain values, the elastic strains are negligible and the rigid-plastic model is satisfactory. The results of Budiansky and Wu indicate that the result obtained by Taylor is 7.7 pct high at a plastic strain which is two times the elastic strain at the initiation of yield. By defining the anisotropy in terms of relative values, the ratio of yield strength at orientation ?, to that measured in the rolling direction, the effect of the discrepancy in Taylor's solution is considered to be of lesser consequence. Therefore, it is anticipated that an analysis based on Taylor's solution, which can be quite straightforward, should provide a reasonable estimation of the anisotropy of materials having a preferred orientation texture. OUTLINE OF TAYLOR'S METHOD In fee metals there are four possible slip planes (the octahedral planes) and in each there are three possible slip directions (the edges of the octahedron), that is a total of twelve possible slip systems. von Mises16 has shown that at least five independent slip systems must become operative in each grain of the polycrystalline aggregate in order to preserve continuity of strain. With this geometrical requirement as basis and the assumptions previously listed, Taylor determined the operative slip systems for a number of orientations of the tensile stress axis specified in the unit stereographic triangle. For the ith slip system, the critical shear stress

Jan 1, 1967

By E. S. Bardwell, R. J. Lapee

Twenty years ago, W. T. Burns, in his paper presented at the Butte Meeting of the Institute,' discussed the general scheme then in use in the electrolytic copper refinery of the Anaconda Copper Mining Co. at Great Falls, Mont., for removing impurities from tank-room electrolyte and controlling its acid content. Since then marked changes have taken place in copper-refinery practice at Great Falls. The electrolytic copper refinery in use in 1913 has been replaced by a new and entirely modern plant capable of producing up to 27,000,000 Ib. of cathode copper per month. With the building of the new plant in 1916, the treatment of converter anodes was discontinued. At first the substitution of refined anodes for converter anodes resulted in a decrease in the impurity content of the anodes, but as time went on, changes in metallurgical practices at the smelter resulted in substantial increases in the impurity content of the anodes. The leaching of the silver slime to remove copper before shipment to Raritan for treatment further added to the purification problem. The fact that the scheme of purifying electrolyte which Mr. Burns described in his paper has proved adequate for our needs under a wide variation of conditions speaks well for its essential soundness. Method of Purification Briefly, the method adopted for purifying tank-room electrolyte at Great Falls has been as follows: Each day a certain volume of tank-room electrolyte is run off and sent to the purification plant, where it is boiled down to approximately 46' 136. The concentrated electrolyte is then sent to crystallizing tanks where the bulk of the copper is crystallized out as copper sulfate. The mother liquor is then passed through insoluble anode tanks to remove the last of the copper and most of the arsenic and antimony. It is then either returned to the tank room direct or boiled down to 55' Bé, the iron and nickel salts crystallized out and the mother liquor returned to the tank-room circuit as restored acid. Prior to 1930 all of the evaporating was done in lead-lined tanks 13 ft. in diameter by 4.5 ft. deep, provided with lead heating coils through which steam at 30 lb. gage pressure was circulated.

Jan 1, 1934

By S. F. Ramseyer, E. A. Steigerwald

INFILTRATED structures represent composite materials which are capable of combining high-temperature strength with adequate low-temperature toughness and thermal shock resistance. Although copper- and silver-infiltrated tungsten structures are actually being used in rocket nozzle hardware, adequate understanding of the fracture mechanics of these composite systems is not available. Specifically the relative importance of the strength, ductility, and modulus of the infiltrant in determining composite properties is not known to the extent that optimum composites can be selected. The major portion of experimental effort in the area of composite strength has been devoted to fiber-reinforced systems1 or to systems where a discontinuous phase is imbedded in a relatively ductile matrix.2'3 In the case of high-temperature systems, which are composed of a relatively brittle matrix, such as tungsten or an oxide, a continuous phase exists for the propagation of a crack. The method by which the presence of a conjugate ductile continuous phase influences the gross properties of the composite represents an area which requires further investigation. This technical note presents results which evaluate the effect of infiltrant strength on the strength of the tungsten-base composite. A tungsten matrix and copper-base infiltrant were selected for the initial studies because of the ease of fabrication. Tungsten structures with nominally 20 and 30 pct porosity were evaluated. The porosity was controlled by varying the initial powder size and a ratio of open-to-total porosity greater than 95 pct was obtained by selective sintering cycles. The processing sequence involved hydrostatic pressing followed by a 72-hr presinter in hydrogen at 2000° F and a final sinter at 4000°F for 4 hr in vacuum. The 20 pct porous structure was obtained

Jan 1, 1965

By AIME AIME

NAPOLEON'S dictum that an Army travels on its stomach has not changed in this present war, but the things an Army's stomach calls for would be more than strange to Napoleon. Today one of the main articles of diet for the mechanized army is oil and gasoline, and the chief and most efficient source of 'apply overland is the pipe line. It was a flexible 4-in. pipe line that supplied the voracious appetite of tanks, trucks, jeeps, and planes across the North African desert. and it is the 1800-mile pipe line from Calcutta to Kunming, Yunnan Province in China, the longest in the world, that supplied oil and 100-octane gas for the trucks, tanks, Jeeps, and planes fighting on the Assam-Burma-China front in recent months. Completion of this approximately 1800-mile pipe line to China over rivers that had never been bridged, over hill that towered 9000 ft., and over swamps

Jan 1, 1945

By L. R. Grabill

The Bassick mine, located six miles east of Silver Cliff, Colorado, has, ever since its discovery, been noted for peculiar features. Some of these characteristics exist in one or two other mines, while some are entirely unique. Among these peculiarities I have selected the most noticeable for treatment in this paper: First. The methods of deposition of the ores, which is not, as in ordinary veins, in strata or layers parallel to the walls of the fissure. The ores are arranged in concentric layers upon detached and abraded fragments of the walls; each ore in a separate stratum, and always in the same place in the series. Second. The characteristics of the fissure or opening; its shape and dimensions; its contents, or the vein-filling; and its verticality. Third. The peculiar products of the mine. The most noticeable of these products is charcoal, which is occasionally, and at long intervals, found throughout the ore-body, and in the surrounding conglomerate, from the surface down to the present depth, which is something over eight hundred feet. The existence of charcoal here is, as far as I know, the only instance of its discovery in mines of metallic ores. Fourth. Besides the charcoal, there are other products, in themselves not peculiar, whose manner of arrangement and composition are unusual. The mine is situated near the centre of a small rounded hill of eruptive trachytic rock and feldspathic conglomerate. The diameter of the base of this hill varies from 700 to 1200 feet, and its height is 200 feet above the general level. A cliff or outcrop of fine conglomerate is exposed on the southwest side of the hill. On the northeast it joins by an upward slope the fine-grained, hardened feldspathic paste of Mount Tyndall, which rises 600 feet higher, and of which the elevation containing the Bassick mine thus forms an arm. On visiting the mine, one's attention, whether he is a scientist or not, is immediately attracted by the unusual method of arrangement of the ore. It is seen to be disposed in concentric layers around fragments of trachyte. These fragments, of which each one con-

Jan 1, 1883

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

By A. Bauer, P. Calder, N. H. Carr, G. R. Harris

Smallwood mine is part of the Iron Ore Company of Canada's Carol Lake operation and is situated in Labrador, 240 miles north of Sept-Iles, Quebec. Last year, 15 million tons of crude ore were crushed to yield 6.3 million tons of concentrate and pellets. This year the figures will be 17 million of crude and 7 ¼ million tons of concentrate and pellets, which is the full plant capacity. Carol Lake ores consist primarily of specularite and magnetite mixed with quartz. Since both rotary and jet piercing drills are used, it is often desirable in planning to know in which regions of the orebody, or new orebodies, a particular drill will be most economic. This makes it necessary to establish a correlation between drillability and pierceability and some physical rock property. For the rotary drills a good correlation was found with penetration rate and grinding factor index. The jet piercers were found to have a reciprocal relationship in the sense that the best rotary ground was the worst jet ground and vice versa. It is also indicated how an economic comparison could be made using these penetration rate versus grinding factor index curves, the hole size distribution curves for single pass and chambered holes, and the mine distribution curve for grinding factor index.

Jan 9, 1965

By K. M. Weigert

The position of the three-phase field between the alpha and the beta phases was established. The exact location differs from previous assumptions. The extremely high strength and hardness values were found near the phase boundaries of the ternary compositions. IN 1929, UenoL investigated vertical sections of the Ag-Cu-Zn diagram at constant silver and zinc values. From the evaluation of cooling curves and microscopic studies, he concluded that there was no evidence of a three-phase field in the solid state between the a and ,8 fields. The failure to find evidence for this field was due to the fact that it exists only in a very narrow range of compositions and requires special methods of heat treatment to establish phase equilibrium. In a later publication on the same subject Keinert2 rearranged Ueno's diagrams to conform with the basic phase rules. The existence of a three-phase field was postulated in the solid state between the a phases and the homogeneous ,9 phase between the Cu-Zn and the Ag-Zn binary border systems. The approximate location was based on a few microscopic observations of the structure and it was pointed out that the exact position could be determined only by a larger number of experiments. In the twenty years following these investigations alloys of Ag-Cu-Zn have become of general interest due to various technical applications, principally for brazing. In the course of an overall investigation of the physical properties of ternary Ag-Cu-Zn alloys the author found extremely high values of hardness and strength in alloys of compositions between the a and the yS fields. The exact location of the intermediate phase fields was established by the evaluation of more than a hundred cooling curves and microscopic mountings. Experimental Procedures Preparation of Test Samples: At the beginning of the investigation samples were chillcast into Vi in. diameter iron molds to determine hardness, strength, and the mechanism of primary crystallization. These

Jan 1, 1955

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By H. H. Dievendorff, F. W. Hertel

The method of drilling deep wells into the earth for the recovery of oil and gas is beset with many hazards. This is especially true in the Ventura Avenue field, which has the distinction of being the hardest field in California in which to complete a deep well. The hard, shifting and squeezing formations must be penetrated to great depths in the face of tremendous gas pressures. This field presents problems that keep the operators abreast with all of the latest developments in oil-field tools and machinery and in oil-well drilling practices. Equipment must be strong, and adapted to deep-well drilling and the handling of long heavy strings of casing. High-pressure sands require the utrnost care and attention of the operators and no chances can be taken, since a serious blowout may cause the loss of a well that has cost months of labor and expense. Equipment must meet these requirements or be discarded. Although the deepest wells in the world are not in this field, nor hav:. the longest strings of casing been set, nevertheless, the consistency with which deep wells are drilled and long strings of casing are set places the Ventura Avenue field foremost, in this respect, among the oil fields of the world. The V&apos;entura Avenue field dors claim the deepest commercial oil-producing well in the world, in the Shell Co. of California&apos;s "Edison" No. 18. This well was drilled 7015 ft. and came in flowing 3280 bhl. of oil per day. This field also claims the deepest average depth of producing wells in that its Ill producing wells average 5676 ft. in depth. Of these 111 producing wells, 50 arc 6000 ft. or deeper, and 16 are 6500 ft. or deeper. Also, of the 111 producing wells 100 arc flowing, and 11 arc pumping wells. This paper is intended to set forth the methods used in the drilling of deep wells with rotary tools and the handling of long heavy strings of casing in the Ventura Avenue field.

Jan 1, 1928

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By Charles L. Harness

STRONTIUM is an essential constituent of celestite (strontium sulphate), of the rarer strontianite (strontium carbonate), and of a few very rare minerals. Celestite is the chief ore but strontianite is more valued except for making the purest strontium salts, because of its ease of processing. The public knows strontium mainly as the source of the red flame in fireworks but it has many other uses. PROPERTIES The celestite of commerce is a massive mineral of varying texture: coarsely crystalline, fibrous, bladed, very fine grained or earthy. The color varies greatly with the nature of the impurities but the purer specimens are light blue (Latin, caelum, sky) or white. The strontianite of commerce is a massive mineral, more or less coarsely crystalline. The color varies with the impurities. Distinctive characteristics are effervescence with acids, density (3.68 to 3.71), and crimson strontium flame. A typical British celestite before World War II analyzed: SrSO4, 96.55 pct; SrCO3, 0.17; BaSO4, 0.25; CaSO4, 0.54; MgCO3, 0.15; R20,, 0.90; Si02, 1.38.10 A German strontianite analyzed: SrCO3, 90.9 pct; CaCO3, 7.5; BaCO3, 0.1; Fe2O3, 0.05; A1203, 0.1; SiO2, 0.04; S, 0.1; P, 0.005.10 ORIGIN AND MODE OF OCCURRENCE According to Clarke,9 strontia forms about 0.02 pct of the crust of the earth and is present in most igneous rocks, but in smaller quantities than barium. Under certain conditions, large masses of celestite are deposited from sea water with anhydrite. The presence of large amounts of celestite in some saline deposits and its absence in others suggests that the deposition of celestite depends on whether certain as yet undetermined concentrations of sulphate and chloride ions are reached in the brines. The most extensive of these sedimentary deposits are those of the Keuper (Triassic) in England, of the Zechstein (Permian) in Germany, and of various Cretaceous formations in Texas, Arkansas, and Utah. Of the deposits of southeastern California and western Arizona,

Jan 1, 1949

By Richard S. McCaffery

This paper considers certain aspects of the acid bessemer process, particularly in its relations to the duplex process—that combination in which the pig iron is first desiliconized and decarburized in acid bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not. make the bottoms of basic or neutral material?&apos; As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic. or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 1, 1922

By Richard S. McCaffery

This paper considers certain aspects of the acid bessemer process, particularly in its relations to the duplex process—that combination in which the pig iron is first desiliconized and decarburized in acid bessemer converters and then dephosphorized in basic open-hearth furnaces. The acid bessemer process employs an acid-lined converter and produces an acid slag. The blow is usually thought to eliminate the silicon and manganese as oxides and then to burn off the carbon as carbon monoxide On account, however, of the relatively large amount of metallic iron present in the converter, compared with the relatively small amount of the impurities it is desired to oxidize, the first reaction in the converter probably is the formation of iron oxide, which dissolves in the bath and acts as an oxygen carrier for the silicon and carbon. As soon as iron oxide is dissolved throughout the bath, the oxidation of silicon commences; but in the early stages of the blow the mass law would indicate that iron oxide must form first, and this oxide probably increases up to some saturation point. The molten metal in the converter from the early stages of the blow right through to its completion remains basic, while the slag produced is siliceous. This fact is shown by the corrosion of the acid bottom and the tuyeres, which is greatest at the tuyere orifice where oxidation is most active and where there is the most iron oxide. Why does this acid bottom corrode? Because it is attacked by a base. The thought, therefore, suggests itself, why not. make the bottoms of basic or neutral material?&apos; As the converter slag is acid, those parts of the converter coming in contact with the slag should be acid; but those parts of the converter that are in contact with the molten metal saturated with metallic oxides should be basic. or neutral. Bessemer operators have for some time tacitly admitted this condition, for the blast pressures have steadily increased with the object of keeping the metal in suspension, and so preventing bottom corrosion; if the molten metal were not basic, it would not attack an acid bottom. In addition, the tuyeres are bunched together at the middle of the bottom and a clear space is left around the outside of the bottom; if tuyeres are placed too near the side walls the

Jan 1, 1922

By E. L. Swarts

In the course of a program on high-temperature processing and electrowinning of uranium at the Knolls Atomic Power Laboratory,&apos;&apos; it became necessary to give attention to the interaction of molten uranium with graphite. Although it is known3 that a protective interface layer may form, details of this reaction have not been reported. Unfortunately it was impossible to complete the planned experimental program. However, the general problem is considered of sufficient interest to warrant reporting those preliminary results actually obtained. EXPERIMENTAL PROCEDURE Interface carbide layers were formed by melting samples of cleaned uranium metal in small closed graphite crucibles. Equilibrations were conducted in vacuo or in an atmosphere of dry helium at temperatures ranging from 1150" to 1400°C and for periods of from 24 to 240 hr.

Jan 1, 1960

By J. Mizrahi, A. Brillantshtein, A. Mitzmager, O. Schächter

The separation of synthetic mixtures of heavy minerals by hindered settling classification and jigging was comparatively tested in water and five organic heavy liquids, of various specific gravities and viscosities. It was found that in the hindered settling classification process the separation efficiency was directly proportional to the concentration criterion, the liquid viscosity being a minor factor. There is therefore a decisive advantage in using heavy liquids as classification medium. In the jigging process the advantage of using a heavy liquid is masked by the detrimental effect of a higher liquid viscosity, which, in this case constitutes an important factor. Considerable interest has been aroused lately by the development of mineral beneficiation techniques 1,2 using TBE (tetrabromoethane), a heavy liquid of specific gravity of 2.96, which has been made available for industrial use by a new process3 producing TBE directly from the Dead Sea brines at a reasonable price. Most of the applications investigated until now were based on the sink-float separation of minerals in a heavy liquid of intermediate specific gravity. The TBE can be conveniently diluted with many organic solvents, and thus sharp separations are possible in a wide range of specific gravities up to 2.96. Although this maximum specific gravity is sufficient on most cases for the elimination of the bulk of the barren gangue and the production of marketable concentrates, some practical problems came up for investigation in which the separation of two (or more) minerals, heavier than TBE, was required.* *Among the cases studied in the IMI Laboratorles which fall into this category we can mention: alluvial deposits, such as heavy minerals in sea sand, tin deposits, or ground coarse-grained rocks, such as pegmatites. In such cases where, due to the petrographic structure, further fine grinding is required in order to achieve the liberation of the heavy components, the

Jan 1, 1964