Search Documents

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770' C., tungsten 3350' C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By W. S. N. Waring, E. C. Bain, E. S. Davenport

The more familiar compositions of both the iron-carbon-chromium' and the iron-carbon-tungsten2 systems have been investigated with a degree of thoroughness which has permitted the construction of their three-dimensional equilibrium diagrams; and it is probable that these equilibrium diagrams are sufficiently accurate for the present metallo-graphic needs. Strangely enough, in spite of their importance, the alloys of iron, carbon and manganese apparently have not been investigated in the same systematic manner, and so far as is known, no three-component equilibrium diagram for this system is available. Even iron-carbon-nickel alloys3 have been studied rather more thoroughly; for these the solidus and liquidus surfaces have already been determined, but the solid transformations in this, as in the manganese system, have not been reported systematically. The present paper deals with the constitution at equilibrium of a series of 36 iron-carbon-manganese alloys of commercial purity limited by 1.5 per cent carbon and 15 per cent manganese, a range of compositions including most of the manganese steels. The temperature range of melting has not been determined, nor has the high-temperature (delta iron) ferrite equilibrium been included in the study, it being considered that the more important characteristics of the manganese steels are their ordinary transformations in the solid state. The delta iron region is almost certain to be a small tetrahedron not very different in magnitude or contour from that in the iron-carbon-nickel diagram. It is probably true

Jan 1, 1932

By R. L. Templin

The increasing use of aluminum and its alloys in commercial fields tias demanded a better understanding of their machining properties. This fact is exemplified by problems that have arisen in the automotive and airplane industries, but many in other fields might be cited. As pure alunlinum and its alloys in their various commercial conditions show appreciable differences in their machining properties, it is not surprising that quite divergent solutions have been offered for the machining problems encountered. However, if the fundamental requirements of the most suitable cutting tools for these metals are understood, these machining problems lend themselves more readily to satisfactory solutions. Since the machining of free cutting brass and mild steel is understood by most persons accustomed to working these metals, it may serve our purpose better to first make a general comparison of the tools more commonly used in machining these metals with the tools most suitable for machining aluminum, then proceed to a more specific discussion of the individual tools. Comparison oF Cutting Tools Cutting tools commonly used for machining free cutting brass usually have little, if any, top and side rake; they are ground on a medium to coarse abrasive wheel and used without any cutting compound or with a cutting compound that has a paraffin base. Those ordinarily used for steel have some top and side rake, are usually ground on a medium to fine abrasive wheel, and are often used with soluble-oil cutting compounds. The proper tools for aluminum and its alloys should have appreciably more side and top rake than the tools for cutting steel; should have very keen edges obtained by grinding with fine or very fine abrasive wheels supplemented in many cases by hand stoning with an oil-stone; and should be used with suitable cutting compounds whenever possible. In many cases, tools suitable for machining aluminum and its alloys are not appreciably different from tools commonly used for cutting hardwoods. The front clearance of a tool most suitable for machining aluminum and its alloys should be about 6°, the top rake from 30" to 50°, making the total angle of the cutting edge of the tool from 35' to 55". A side

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride'-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By E. E. Barker

Although flotation was known to be a successful process prior to 1312, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on a full flotation basis. Effect of Flotation on Ore Reserves The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Jackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent. became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent. and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By P. D. Gorsuch, D. L. Newhouse, Irvin R. Kramer

ALTHOUGH many methods have been suggested for the calculation of tensile strength and yield point from chemical composition, their usefulness has been limited to a particular cooling rate or section size. Further limitations have been imposed by failure to take into account many of the alloying elements that exert a considerable influence on the tensile strength or yield point. These systems, nevertheless, have filled an important need in many instances. The value of a system for the calculation of the tensile properties from the chemical composition and cooling rate is that it permits the prediction of the effect of alloying elements and heat-treatment on the mechanical, properties, so that more efficient use of alloying elements may be made. Furthermore, it aids in the choice of steel for a given application and tends to decrease the number of steels that otherwise would have to be tested. It is the purpose of this work to present a method of calculating tensile strength and yield point from the chemical composition and to suggest a method of correlating the tensile-strength and yield-point factors and cooling rate. Steelmakers have been interested for many years in the calculation of the tensile strength of hot-rolled steels. Quest and Washburn' summarize several of the attempts that have been made to devise formulas. They show the inadequacy of each of these formulas and present one of their own. It is apparent from their work that a simple additive equation of the type TS = A + BX + Cy + DZ + ? ? ? , where A, B, C, D, etc. are experimentally determined constants and x, y, z, etc., are the percentages of alloying elements present in the steel, is not adequate to analyze fully the situation encountered in the calculation of tensile strength. For example, it was found that the difference between the calculated and observed values became progressively greater as the carbon and manganese contents were increased. Therefore, the effect of manganese was given as a function of the carbon content. Grossmann,2 in his work on the hardenability of quenched steels, and Walters,3 in his method of calculation of tensile strength of normalized steels, present two cases in which multiplying factors were successfully used to express the combined effect of alloying elements. The factors in both cases were obtained from the fractional increase in hardenability or tensile strength with increase of alloy content. Yield point often is more important in design than tensile strength. For quenched and tempered steels a linear correlation exists between yield and tensile strength .4 This is not true, however, for normalized

Jan 1, 1946

By C. P. Fiske

THE pottery of the New Jersey Zinc Co. (of Pa.) is equipped to make three classes of refractories; namely, spelter vessels, spelter condensers; and high-grade fire-brick. The most important of these are the spelter vessels, on account of the extreme severity of the service which they must perform, necessitating great care in the selection of materials and in the whole process of manufacture. Next to the spelter vessels in importance? come the condensers, as large numbers are used in the manufacture of spelter, and improvements m quality result in material decreases in working cost. , While the fire-brick which form the laboratory, or high-temperature portion of the spelter furnaces, are placed at the foot of the list, they-are nevertheless of much importance, since high quality will decrease the frequency of the always expensive shutdowns for repairs. To promote simplicity, the manufacture of these three products will be described separately in this paper, except in so far as materials and the crushing and handling system common to all are concerned. Materials Bond Clay.-The bond clay used entirely at the Palmerton pottery is a St. Louis clay furnished by the Grand View Fire Clay Co. It is stored in a system of covered bins, and no attempt is made to weather -it in the, accepted sense of the term " weathering." Some years ago our clay was weathered before pugging, but we did not find the benefit sufficient to offset the additional handling and the loss. of clay incurred. Furthermore, we believe that the rotting of the pugged mix (described later), accomplishes the same results to better advantage. That there is some action taking place in the clay while stored in the covered bins, however, is, evidenced by an increase in volume which at times has caused damage to the retaining walls of the bins. We have at present a stock of bond clay weathering in the open, and when this is put into service an opportunity will be afforded for making comparisons-with the clay as usually handled.

Jan 10, 1917

By Donald H. Beilstein

The St. Joe Minerals Corporation Lead Smelter and Refinery have been in continuous operation at Herculaneum, Missouri since 1892 as the Herculaneum Lead Smelting Division. Over the years, the plant has undergone many changes to increase production, improve the technology, reduce the cost of operations, and produce the highest grade of primary lead. The latest alterations were begun in 1950 and completed in 1970 and have resulted in the Herculaneum Smelter capacity being increased to in excess of 200,000 tons per year (180,000 metric tons). This increase has made the Herculaneum Smelter the largest in the United States, and second largest in the world. This paper will describe the Herculaneum Smelter equipment, processes, and material balances. Particular emphasis will be given to the McDowell-Wellman 10' x 100' (3 x 30 meter) up-draft sinter machine and ancillaries; to the new Heavy Smelting Department (blast furnaces and drossing section); to the new Lead Refinery and its automatic casting equipment and to the gas handling system including the 340 tons per day (305 metric) Sulfuric Acid Plant utilizing a -four pass converter. The description will include photographs, flow sheets, tonnages and assays where applicable.

Jan 1, 1970

By H. Sevim, T. M. Yegulalp

This paper summarizes recent developments in modeling of underground coal slurry haulage networks to determine optimum design and operating parameters. The model presented is based on a stochastic dynamic program¬ming formulation. It is applicable in any typical room-and-pillar or longwall mining configuration commonly practiced in the US. The formulation and structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1985

By A. H. Dierker

NEXT to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate, figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry.

Jan 1, 1929

By D. W. Fuerstenau, G. D. Gumtz

Use of the discretized batch-grinding model for the simulation of locked-cycle grinding tests from batch-grinding data is illustrated. The simulated results were compared with actual locked-cycle experimental data for the dry grinding of dolomite. To illustrate the utility of this simulation method, a number of relationships between operating and performance parameters were generated, including relations between batch grinding and the Bond test, the production rate and the circulating load, and the production rate and the product size. A large amount of testing is done each year in the mineral industry for use with grinding unit cperations, and much of the experimental test data is obtained by the tedious locked-cycle testing procedure. In addition to being experimentally complex and requiring large amounts of sample, the very nature of the locked-cycle experiment yields results that cannot readily be interpreted. The attempts that have been made to model comminution systems during the last few years may provide a better and simpler way to obtain and analyze grinding test data; these models involve elements of both fitting to "model equations" and deterministic representations.1-1 The traditional engineering design techniques for comminution systems have relied mainly upon large amounts of industrial operating data that have been correlated with locked-cycle grinding data.',' Bond's empirical mill-design procedure involving locked cycle testing remains the most generally available method to this day. The purpose of the present paper is to show how much more useful data can be obtained from a simple batch-grinding experiment that provides information which subsequently can be utilized with population balance models of the grinding process to simulate locked-cycle behavior. These simulation results can, of course, be used in Bond's general design scheme. However, the combination of batch-grinding tests and the population balance model allows many more conditions to be considered than do single laboratory tests under specific locked-cycle conditions. The use of these simulation techniques for prediction of locked-cycle behavior represents one of the first practical applications for the simulation method in comminution.

Jan 1, 1971

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Albert G. Zima

According to recently puhlished statistics, it is predicted that as much oil must be produced during the next 16 years as has been produced during the past 75, in order to satisfy the high rate of consumption of petroleum products. During 1934, over 17,000 oil wells were completed in the United States, and it is expected that over 20,000 additional wells will be drilled during the current year. Were it not for the remarkable progress made during recent years in the improvement of drilling technique and in the development of equipment used in the production phase of the oil industry, it is doubtful whether sufficient oil could be produced to meet present requirements. A few years ago, wells seldom were deeper than 3500 to 4000 ft., owing to the limitations of the drilling methods and equipment employed. Today, however, through the application of scientific drilling methods and the adaptation of modern equipment and improved materials, many wells range from 6000 to 8000 ft. in depth, and a few recent completions exceed 10,000 feet. Drill Tools Modern rotary drilling tools are the product of ingenious design and careful selection and adaptation of materials used in their construction. They must withstand terrific abrasion and, because of their compactness, must be designed to resist exceedingly high unit stresses. In bits, core drills and reamers, the bodies are made of either forged or cast alloy steels, heat-treated to develop a combination of high strength and toughness. To provide sufficient strength to the threaded portions and to protect the threads from distortion or damage, the box or pin sections of the tools are hardened to approximately 310 to 330 Brine11 hardness number. Drill and reamer cutters are generally of the movable type; i.e., serrated cones, cylinders or disks, which can readily be replaced when

Jan 1, 1935

By Earl Oliver

CONTENTS PAGE A.I.M.E. Stabilization Committee Activity 3 Definition of Capture Rule: Robert E. Hardwicke 4 Westmoreland Natural Gas Co. vs. DeWitt 5 Kelly vs. Ohio Oil Co 5 Bernard vs. Monongahela Gas Co 6 Definition of Ownership in Place 7 Prospective Stabilization Remedies 7 Dean Roscoe Pound's Four Tests of Practicability 7 I: Mechanically Feasible 8 Capture Rule 8 Ownership in Place 10 Mechanical Separation Method 10 Engineering Appraisal Method. 11 II. Economically Advisable. ., . 13 Capture Rule 14 Ownership in Place 14 III. Politically Wise 14 Capture Rule 14 Ownership in Place 17 IV. Legally Sound 18 Capture Rule 18 Ownership in Place 19 Dean Henry M. Bates' Analysis 19 Resume 22 THE A.I.M.E. Stabilization Committee was named in 1932 to ascer-tain whether some practical substitute could be devised for the Rule of Capture, which was generally credited with being the major cause of instability in the Petroleum Industry. After considerable intercommittee correspondence a letter was received from. E. DeGolyer under date of Jan. 25, 1935, in which he discussed the possibility of modifying rather than discarding the Rule of Capture. He summarized his proposal as follows:

Jan 1, 1937

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Apr. 10, 1917, to May 10, 1917. ANDERSON, GEORGE K., JR., Supt., Iron Ore Mines, The Low Moor Iron Co. of Va., Longdale, Va. AVERY, DAVID, Met Collins House, Collins St., Melbourne, Vic., Australia. BATES WILLIAM T., Shift Foreman, American Zinc Co. of Tenn., Mascot, Tenn. BIRD, ELMER, Min. & Civil Engr P. O. Box 1483, Boise, Idaho. BLACKBURN, JOSEPH R., Vice-Pres. & Genl. Mgr., Austen Coal & Coke Co., Austen, Preston Co., W. Va. BOTSFORD, FRANK P., Asst. Genl. Supt., Eastern Mesaba, Pickands Mather & Co., Gilbert, St. Luis Co., Minn. BRADEN, SPRUILLE, Min. Engr., Andes Exploration Co. of Maine, Casilla 83-D, Santiago, Chile South America. BROWNE, DAVID G., Mill Designer, New Jersey Zinc Co., 55 Wall St., New York, N. Y. BRUDERLIN, EMIL J., Met. Engr., Ohio & Colorado Smelt. & Ref. Co., Salida, Colo. CAMPBELL, DONALD C., Min. Engr., Campbell Wells & Elmendorf, 114 James St., Seattle, Wash. CARRIGAN, J. J., Asst. Genl. Supt. of Mines, Anaconda Copper Min. Co., Butte, Mont.

Jan 6, 1917

By Charles Hart

THE art of electric smelting came with the turn of the present century and owes its existence to the introduction of alter-nating current, which found its first wide use in the establishment of the great power plants at Niagara Falls, N, Y. Prior to that time current was largely direct. The fur-naces were electrolytic in nature and found their first metallurgical use in the produc-tion of aluminum, and this process still prevails. The normal production of pig iron up to that time was carried on in blast furnaces in which charcoal, coke and anthracite were used as the fuel. This new electric process called for sufficient carbonaceous material to reduce the oxides and impregnate the pig iron with sufficient carbon, but the remainder of the energy was to be supplied by electric power. The chemical reactions are essentially the same in electric smelting as obtains in the older blast furnace. All of these data are so well known in both methods as to need no discussion at this time, for they can be found in scientific publications and books written during the first two decades of this century.

Jan 1, 1940

By G. St. J. Perrot, S. P. Kinney

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By S. P. Kinney, G. St. J. Perrot

Consumers of metallurgical coke are agreed that the quality of their fuel plays an important part in the performance of the furnace. Less unanimous agreement is evident when the properties of a desirable coke are discussed or when consideration is made of suitable testing methods by which the worth of a coke for metallurgical purposes may be determined quantitatively. Much has been written of the importance of combustibility as a factor in determining the performance of coke in the blast furnace and it is generally believed that cokes vary widely in this respect. The usual operating data of the furnace afford little evidence as to the combustibility of the fuel. As a part of a general investigation of the properties of metallurgical coke, the Bureau of Mines has explored the hearth combustion zone in a number of blast furnaces by means of water-cooled gas sampling tubes driven into the hearth through the tuyeres. The attempt has been made to determine the difference in combustibility of cokes varying widely in physical properties. Data have also been obtained in an experimental combustion furnace at the Bureau laboratories in Pittsburgh. This paper gives the results of experiments, made at eleven blast furnaces, in which the composition of the gases was determined at various points in the hearth in the plane of the tuyeres. Further work is in progress in which the zone above the tuyeres will be explored. Factors Affecting Coke Combustibility Brassertl has defined combustibility as the rate of progression of combustion, or, in other words, the speed at which the carbon molecules

Jan 1, 1923

By Emil Gathmann

(San Francisco Meeting, September, 1915) THROUGH wide experience at numerous mills in the United States I have found that there is a decided difference of opinion among the producers of steel as to what constitutes commercially sound steel. Some metallurgists insist upon having, for certain grades of steel, a so-called "open steel," -i.e., one which contains numerous blowholes of varying sizes, and consequently but little volume of true pipe, although a central intermittent shrinkage cavity often extends well down into the ingot: Such blowholes and pipe are expected to weld up during rolling or forging, because their surfaces are not oxidized. Even if this be admitted, included slag particles and a high degree of segregation are bound to be present in the product of such ingots. Blowholes are the result of an oxidized heat, and all heats, unless made or finished in the electric furnace, are oxidized more or less. Subsequent deoxidation, or rather degasification, either in the ladle or in the mold, or in both, is necessary to reduce or prevent blowholes. As is well known, a greater yield of billets or sheets is secured from the ingot by allowing the formation of blowholes, but this is undoubtedly obtained at the expense of the quality of the product. Decided segregation of carbon, phosphorus, and sulphur, as well as small included slag particles, undoubtedly exists throughout the greater portion of all so-called open steel, and cannot be removed by cropping. The first requisite for sound, homogeneous steel ingots and blooms is therefore, in my opinion, so to treat the steel in the furnace, ladle, and mold that "piping" steel is produced. The line of demarcation between harmful and so-called "harmless" blowholes is practically impossible to define. Is it not, therefore, the better and safer practice to use means for the elimination of blowholes and correspondingly reduce the segregation and allow the formation of a well-defined shrinkage cavity or pipe .at the upper end of the ingot? With the relatively cheap deoxidizers available at the present time, e.g., ferro-silicon, aluminum and titanium,

Jan 8, 1915