Search Documents

By W. J. Wrazej

THE measurements on the formation of multi-layered scales on pure iron1 and the metal -lographic examination of the produced layer of FeO, Fe,O,, and Fe2O3 shown in micrographs2 throw much interesting light on this apparently well-known subject. Professor Paidassi announced2 that in a few months7 time further results are going to be published with regard to the growth of Fe2O3 and Fe2O3 layers on an Armco iron as a function of temperature. Because of the very thin layers of Fe2O3 which are shown by Paidassi (Fig. 10 of ref. 2) when samples were scaled in air at 700°C for 4 hr and because this is not in agreement with the present author's previous observations, the following experiment was recently carried out. Polished cylindrical samples 13/64 in. in diam and 1/4 in. long from electrolytic iron used for spectro-graphic work (Hilger, H.S. Iron rods, F.693) and an Armco iron sample 1/4 in. in diam of the same length were suspended in a muffle furnace on Nichrome wire and annealed in air for 4 hr at 700°C 5OC. Because of the known easy peeling off of the Fe2O3 layer which is mainly in the form of powder (purple red dust on the surface) the samples were protected against any draft and shock. After annealing, the samples were cooled in air and placed in the mount-

Jan 1, 1954

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

Low-power, high-speed, radiation-resistant, monolithic thin-film integrated circuits require thin-film resistors of high sheet resistance which are compatible with the processing requirements for monolithic silicon devices. For this purpose the structure and electrical resistance as a function of temperature were investigated for Nichrome-silicon monoxide cermet films on passivated single-crystal silicon substrates. A suitable material was found to be a mixture of 50 vol pct Nichrome-50 vol pct silicon monoxide. This mixture, when evaporated onto 300°C substrates. showed a low temperature coefficient up to 400°C, at both 270 and 1100 ohms per square. Resistors deposited on room-temperature, 300°, and 500°C substrates were heat-treated at 600°C in air for short periods of H- seed, low-power, radiation-re sis tant, monolithic thin-film integrated circuits'-3 require thin-film resistors of high sheet resistance and low temperature coefficients of resistance which are compatible with the processing requirements for monolithic silicon active devices. The present investigation is directed towards the replacement of the Nichrome in the sandwich-type SO2-Nichrome-SiO resistors, currently used for DTL monolithic thin-film integrated circuits, with codeposited Nichrome-SiO cermet resistors. These Nichrome-SiO resistors are provided with an overcoat of SiO and are deposited onto thermally oxidized silicon wafers used in monolithic mi-crocircuit technology. The cermet resistors are shown to provide a lower temperature coefficient of time totaling up to 45 min. Electron nzicrogvaphs and diffraction patterns were taken of the as - deposited and heat-treated films. These results were then compared with electrical-resistance measurements for each condition. The room-temperature and 300°C substrate films showed a large decrease in resistance. The 500°C substrate film remained stable throughout the entire cycle. Electron-microscopy results show that the increased stability after heating to 600°C is largely due to crystallization of the films which begins in the vicinity of 400°C. The slight oxidation of the films when heated in air had a negligible effect on the resistance. The resistance of the film was a function of the substructure. resistance and a more versatile compatibility with silicon monolithic processing. Previous work3, on chromium-SiO coevaporated cermet resistors on glass and ceramic substrates without overcoats of SiO has been reported. For the present application, the thin films should possess the following ideal requirements: a) a temperature coefficient of resistance as near zero as possible up to 300°C; b) have a sheet resistance higher than 200 ohms per sq to conserve space on the chip; c) be easy to evaporate; d) be oxidiation- and radiation-resistant; e) show long-time stability at 100°C; } be stable in N2 atmospheres up to 600°C for short periods of time (5 to 45 min). Requirements a to e are well-known. The last requirement was optional and was due to a mask elimi-

Jan 1, 1967

By W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1,? Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses.

Jan 1, 1935

By A. B. Cox, L. W. Wark

In the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practised at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts of many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies—the Broken Hill South, the North Broken Hill, and the Zinc Corporation—together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism. After an extensive search of the literature, it was decided to determine in a preliminary investigation whether the effect of chemical collectors could be evaluated quantitatively by the "contact-angle" method. This preliminary investigation showed that with the bubble machine of

Jan 1, 1935

By W. R. Ingalls

In choosing the unusual title given to this paper, in which the term "cyclic " might be substituted for "intermittent," my idea has been simply in respect of precision. We might say old method vs. new method, but that antithesis implies something of substitution that has not occurred and perhaps is not in sight. We may say horizontal retorts vs. vertical, but none of the older retorts are truly horizontal, and there are three different types of vertical retorts. Other complexities might be suggested. There is, however, a broad distinction between distilling that is accomplished in a periodic cycle, generally daily; and distilling that is accomplished continuously, irrespective of whether it be done in the vertical retorts of the New Jersey process or in the retorts of the Trollhät-tan process. In offering a summary of the present state of the art with the intermittent process, I shall not have any idea of exemplifying it through descriptions of any single plants, but shall rather divide among the main steps of the process and outline what is best developed among them. In pursuing this thought, it will manifestly be impossible to make a composition that will exemplify the acme of good practice, for the latter will always be a function of the cost of labor, fuel, etc., which are widely variable. As of 1929, in respect of labor we might generalize the average plant wage in the Pittsburgh-Wheeling district of the United States at $5 per day; in Oklahoma at $3; in Great Britain at $3; in Germany at $1.75-$2; in Belgium and France at $1. With high labor costs the metallurgist will naturally use means of the nature of mechanization that with low labor would be uneconomical when capital charges are taken into account. Nor may we from records of performance safely make positive deductions in respect of the efficiency of different types of furnaces unless they have been tested comparatively under identical conditions in the same works. We shall find gas-fired regenerative furnaces showing coal consumption from 1.2 tons down to 0.7 per ton of roasted ore, which may be ascribable to difference in the thermal value of the coal that is used or to differences in proportions of the parts of the furnace, which is something quite distinct from the principle of the furnace. Thus, we have

Jan 1, 1937

By D. F. Atkins, B. A. Rogers

The constitutional diagram presented herein is relatively simple. Complete mutual solid solubility exists for an interval below the solidus line, a continuous curve with a flat minimum near 22 pct Cb and 1740°C. Upon cooling, the solid solution breaks up, except at the columbium-rich side, from two causes: zirconium-rich alloys transform under the influence of the ß-a transformation in zirconium; alloys of intermediate composition decompose into two solid solutions below 1000°C. The combined effect is the formation of a eutectoid at a temperature of 610°C and a composition of 17.5 pct Cb. The eutectoid horizontal extends from 6.5 to 87.0 pct Cb. Some age hardening effects have been observed in the zirconium-rich alloys but the positions of the solvus lines remain uncertain. IN recent years, zirconium has been produced in much larger quantities than were available previously. Correspondingly, the incentive for studying its alloy systems has increased, as the number of recent publications on alloy systems testifies. However, only a partial diagram of the Zr-Cb system has been published and relatively few references have been made to alloys of the two metals. Hodge' investigated the Zr-Cb system up to about 25 pct Cb. His data on melting points were not sufficiently numerous to distinguish with certainty between the alternatives of a narrow eutec-tic horizontal and a wide flat minimum in the solidus curve. Although Hodge considered his results on transformations in the solid state to be only tentative, he suggested that the eutectoid in the zirconium-rich alloys lay at about 625 °C and 10 pct Cb and estimated that the solubility of colum-bium in zirconium at 625 °C was near 6 pct. According to Simcoe and Mudge,2 less than 0.5 pct Cb is soluble in zirconium at 800°C. These authors observed an increased strength in both the 0.5 and I pct Cb alloys made with hafnium-containing zirconium. According to Keeler,3 the strength of zirconium is increased by addition of columbium to a content of at least 3 pct. Keeler' also observed a maximum in hardness at about 10 atomic pct Cb and commented on the brittleness of alloys of this composition. Anderson, Hayes, Rober-son, and Kroll5 investigated the tensile properties of Zr-Cb alloys containing 5.1 and 12.9 pct Cb at room temperature and at 343°C. The 12.9 pct alloy had a high tensile strength at room temperature but also a low percentage of elongation. All alloys had high elongation at 343 °C. Littona measured strength and elongation values of annealed alloys containing up to 27.5 pct Cb and found low elongation values for all of the alloys of high columbium content. Some observations on the resistance of Zr-Cb alloys to corrosion in water at high temperature have been published by Lustman, De Paul, Glatter, and Thomas' who found that additions of columbium up to 1 pct had only a minor effect on the corrosion resistance of zirconium. Preparation of the Alloys Raw Material: Zirconium of a relatively good grade was available for making the alloys. It was obtained as scrap pieces that had been left over from an operation that included production by the iodide process, melting under a protecting atmosphere, and fabrication to plates. The individual pieces had hardness values of 24 to 32 Ra and a typical analysis is shown in Table I. The columbium also was scrap trimmed from sheets. It was furnished by the Fansteel Metallurgical Corp. and had a high ductility but its analysis was known only approximately. The metal probably contained about 0.5 pct Ta, perhaps 0.25 pct C, and a few hundredths percent each of iron, silicon, and titanium. Melting: The alloys were melted in a tungsten-electrode copper-crucible arc furnace similar to units that have been described recently in the metallurgical journals.'.' The crucible of this furnace is provided with a cavity in which a getter charge can be melted before the melting of the alloy charges. Hardness measurements on the ingots indicate that the getter charge takes up a considerable fraction of the oxygen and nitrogen from the helium atmosphere of the furnace. The alloys used in the investigation are given with their intended compositions, hardness, and melting points in Table 11. Fabrication: All alloys of the Zr-Cb system appear to be amenable to fabrication. At least, all of the compositions listed in Table II could be reduced to wires in a rotary swaging machine. The starting material was either slabs cut from ingots and ground by hand to rough cylinders or narrow strips trimmed from sheets made by cold rolling slabs. However, not all of the alloys could be fabricated satisfactorily by the same method. From 0 to 4 pct Cb and from 20 to 30 pct Cb or more, the alloys could be swaged cold from ¼ in. cylinders to 0.80 mm wires with only one intermediate annealing, sometimes with none. From 40 to 90 pct Cb, the alloys were difficult to swage either hot or cold but could

Jan 1, 1956

By Herbert M. Wilson

We of the employer class represent labor in the social organization and in industry just as truly as do those who labor only with their hands, and, because our labor is chiefly with our brains, the duty is all the more imposed upon us to use those gifts in which we excel in helping steer a clear course through the turbulent waters in which we are now enmeshed. Only their selfish engrossment in the daily tasks they were employed to perform could possibly have permitted the great majority of the intelligent and industrious German people to become terrorized by a handful of the idle, the vicious, and the criminal, whom the elections to the National Assembly showed to be in as pitiful a minority as they are in Russia, in this, and in other countries. It is the leisure unemployment of the I.W.W.'s, the Bolsheviki, and the Sparticans that has enabled them to devote their whole time to a concerted and aggressive struggle against the great majority of those of the world's workers who are unorganized, and who are therefore even in opposition one to the other. In union there is strength, and this was never better illustrated than by these conditions. The great fallacy of our previous attitude toward social and industrial problems has been the belief that labor, by which we commonly mean organized or physical labor, is something antagonistic to and having a different object in life from that great body of unorganized laborers who work with their brains. Our difficulty has been our lack of will or opportunity to think. The hurry of our daily struggle to earn our livelihood under the nerve-racking pressure of modern civilization has left us no opportunity for quiet thought and study. The physical laborer, and above all the laborer in the mines, on the other hand, has all his hours of toil in which to think over, in all their varied aspects, those problems that concern his immediate, personal well-being. As a result he has arrived at perhaps a more true appreciation of the facts of life in their relation to social and industrial conditions than we. Have we not too readily adopted the view that, as the managers of industry under the direction of capital, it has been our duty to think and act in opposition to labor, rather than to realize that we also are laborers, have like aspirations, and should participate in a free and aggressive solution of these problems rather than leave their solution

Jan 1, 1919

George W. Maynard, New York, N. Y.:—It is well known that there are many magnetite-mines of which the ore is too low-grade for direct use in the blast-furnace. For carrying out the sintering process, the preliminary step, in the case of magnetites, is the separation of the ore from the gangue by magnetic concentration. The resulting fine-grain product is very objectionable in the blast-furnace, and when used must be a very small percentage of the charge. The sintering process has saved the situation by furnishing a product which is absolutely ideal on account of its cellular structure. (In reply to questions by W. J. Tudor, and Joseph W. Richards, the following additional information was given by Dr. Maynard.) The percentage of iron in the product is determined entirely by the degree of concentration of the raw material and is practically not increased by the sintering operation. The magnetic concentrates at Port Henry and at the Benson and one or two other mines contain from 65 to 67 per cent. of metallic iron. The cost of sintering is from 39 to 41 cents per ton of product, including superintendence, depreciation, and repairs. The itemized figures are about as follows : Mixing (including labor), 24; power, 9; ignition, 5; repairs, 3; total, 41 cents. Prof. J. W. Richards, South Bethlehem, Pa.:—From a metallurgical standpoint I question the accuracy of the statement on p. 374: " C.—An increased reducibility of the iron so treated. (This has been conservatively estimated as 5 per cent. better than the best available ore.)" It seems to me that when a material is' sintered in this way, the constituents present, as lime, silica, and alumina, have a chance to form a compound with the iron oxide; that such a compound, if formed before the material goes into the blast-

Jan 1, 1913

By O. D. Gonzalez, R. A. Oriani

The migration of hydrogen and of deuterium dissolved in a iron and in nickel induced by an applied electrical potential has been measured over a range of temperature. In all cases the intevstitial solute migrates to the cathode. The deduced charges of transport are positive, independent of or slightly dependent on temperature, and markedly larger for the beavier mass. These results are interpreted as showing predominating momenlum transfer between electron holes and the acticated complex of the elementary diffusion act. THE migration of components of a metallic system under the action of an applied electrical potential is called electromigration or electratransport. This phenomenon has been known since 1861 and is becoming of increasing interest to metal scientists because of the opportunity it offers to explore the connections between mass transport and electron transport. Until recently, reliable data have been very scarce because of the difficulties inherent in the measurements. In addition, theoretical understanding has been either nonexistent or rudimentary and at present this situation is only moderately improved. Whereas the prevalent notion had been (and is still widely held) that electromigration directly reflects the state of ionization of a component in its equilibrium state in the metal, it is now becoming clear that the major, if not the sole, factor is the momentum transfer between the charge carriers, themselves in motion because of the applied field, and the metallic components in their activated state. It becomes important therefore to obtain reliable data over a range of temperature on electrornigration in systems where only one component moves, that is, either in pure metals (vacancy motion) or in interstitial solid solutions. Our choice of systems was dictated by our measurements' of the Soret effect in solid solutions of hydrogen and deuterium in iron and nickel. Indeed, the main reason for making measurements on electromigration at all is that we suspected a mechanistic connection between thermal diffusion and electromigration. In our former paper' we proposed that what is common to both phenomena is the momentum transfer between the charge carriers in the metal and the atom as it jumps from one equilibrium position to another. In Soret diffusion, however, there is in addition the dissipation of the energy of the jumping atom via pho-nons. We have since found that similar ideas for this interconnection have been developed by Fiks.2 In the present paper we will discuss in more detail our understanding of the mechanism of electromigration itself, but we turn first to a presentation of the experiments and results. EXPERIMENTS AND RESULTS Let us consider a metallic system in which only one component, m , can diffuse at the temperature in question, and to which are applied simultaneously an electrical potential gradient, grad cp, and a chemical potential gradient, grad p,. One may write3 for the material flux Jm and the electronic charge flux Je by applying the condition, grad = 0, to Eq. [I] and evaluating grad(um/T) for the isothermal case and for activity coefficient independent of composition over the relevant composition range. ere, c is the concentration and D the diffusivity of the mobile component. The experimental technique that we have used to measure Z* for the isotopes of hydrogen individually dissolved in each of two transition metals has been developed from a method used by Wagner and Heller.4 (A somewhat similar method was also used by Herold.5) A wire or thin rod of the metal under study connects two volumes of gaseous hydrogen at identical pressures; hence grad um = 0. A direct current is made to pass through the specimen, serving to maintain the specimen at the desired temperature and also to produce the electromigration of the hydrogen dissolved in the metal in equilibrium with the gaseous hydrogen. Under these conditions, the flux of hydrogen from one volume to the other is given, from Eq. [I] for grad( um/T) =0by

Jan 1, 1968

By M. Gensamer

A RECENT paper1 described, by means of stereographic pole figures, the preferred orientations produced by cold-rolling low-carbon steel of automobile-body grade. It was found that the surface of the sheet exhibited a deformation texture significantly different from the texture possessed by the inside of the sheet. Efforts to produce the surface texture by buffing a sample exhibiting the normal or inside texture, using a copper lap, have not been successful. In view of the data collected, by Kurdjumow and Sachs2, it was suggested that the surface texture might be the result of partial recrystallization of the normal or inside texture. The recrystallization texture of cold-rolled mild steel was studied by Goss3, but he did not use the pole-figure method, so that his conclusions were in need of verification. For these reasons the work reported in the present paper was undertaken. It had two objectives: (1) to study the general behavior of cold-rolled mild steel on recrystallization below the critical temperature A,, and (2) to attempt experimentally a demon-stration of the genesis suggested above for the surface texture in cold-rolled steel. The material was that used by Gensamer and Mehl, cold-rolled to 97.5 per cent reduction in thickness. Fig. 1 is an X-ray pinhole photo-gram of this material, taken with the beam transmitted perpendicular to the plane of the sheet, using a molybdenum target at 35 kv. with no filter. It is typical of the inside texture, but in it the deformation texture is better developed than in the samples that showed a well developed difference between the inside and surface samples. Specimens from this sheet, which was 0.005 in. thick, were annealed for 5 min. at various temperatures in a lead bath. After about 0.0005 in. had been etched from both surfaces, X-ray photograms were prepared, using the technique described in the earlier paper'.

Jan 1, 1936

By Nicholas J. Grant, Michio Yamazaki

Cast copper alloys containing 10, 20, and 30 pct Ni and 0.75 to 0.80 pct Al were machine-milled into chips, then comminuted in a rod mill to fine flake powder utilizing a number of processing variables. The powders here internally oxidized, mostly at 800°C, in a low-pressure oxygen atmosphere. The consolidated powders were hot-extruded into bar stock. Room-tenmperature tension tests, stress-rupture tests mostly at 650°C, but also at 450° and 850°C, and hardness measurements after various annealing temperature treatments to study alloy stability were perfomted. Excellent room-temperature strength, high rupture strength at 650°C, and resistance to recrystallization at 1050°C were obtained. Problems in optimizing conditions for internal oxidation of Cu-Ni base alloys are discussed. THE interesting high-temperature properties of SAP' have stimulated considerable effort in the study of more refractory alloy systems where the potential for high-strength alloys at high temperature is great.2-13 A number of methods have been utilized to produce the desired fine, hard particle dispersions, of which internal oxidation2,9,7 of dilute solid-solution systems offers considerable promise by virtue of the potential for producing ultrafine, well-dispersed oxides. While most of the published works are concerned with pure metal matrices, a number of investigators have studied the effects of solid-solution strengthening.10,19 Use of more complex alloy matrices (for example, aging systems) has been unsuccessful because overaging still occurs at high temperatures in the oxide-containing alloys.14.15 Solid-solution strengthening is, however, effective at very high temperatures9,10 and might be expected to contribute importantly to the strength of oxide-dispersion strengthened alloys. For this study, internal oxidation of solid-solution alloys of copper and nickel, containing small amounts of aluminum, was chosen as the method of alloy preparation. PREPARATION OF ALLOYS Three copper alloys containing about 10, 20, and 30 pct Ni and each containing 0.75 to 0.80 pct A1 (enough to yield about 3.5 vol pct alumina) were prepared as air-cast ingots measuring 2.5 in. diameter by 6 in. high (see Table I for the analyses). Processing steps for all the alloys were as follows (also see Table 11): 1) Homogenization of the ingot at 982°C (1800°F) for 45 hr in an argon atmosphere. 2) Machine milling of ingots into fine chips. Average thickness was about 0.1 to 0.2 mm. 3) Hydrogen reduction of chips at 593°C (1100° F) for 1 hr to reduce copper and nickel oxides. 4) Rod milling of chips to finer powders. 5) Hydrogen treatment of powders as in step 3. 6) Internal oxidation of the powders. 7) Hydrogen treatment of oxidized powders as in step 3. 8) Hydrostatic compression of evacuated powders. 9) Sintering of compacts in hydrogen. 10) Hot extrusion. Variations in processing among the alloys were made in steps 4, 5, and 10 (see Table 11). In the past, two methods were utilized to internally oxidize alloy powders. Preston and Grant3 surface-oxidized dilute Cu-Al powders to obtain the necessary amount of oxygen to oxidize the solute metal (aluminum and silicon), and then permitted the formed copper oxide to diffuse and react with the solute in an argon atmosphere. Bonis and Grant4 exposed Ni-A1 and other nickel alloys to an oxygen pressure derived from the decomposition of nickel oxide at a preselected temperature, in an argon atmosphere. Both methods are applicable and can be modified to generate a range of oxygen pressures for oxidation of the solute but not the solvent metals. Procedure I: Surface Oxidation of Alloy A3, Cu-10Ni-0.76A1. Powders of -20 to +28 mesh were surface-oxidized at 500°C (932°F) to obtain the desired amount of oxygen for oxidation of the aluminum to alumina; the powder was then sealed in Vycor and heated at 900°C (1652°F) for various times up to

Jan 1, 1965

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By C. W. Nicolson

The Tri-State zinc and lead-mining district is in the northeast corner of Oklahoma, the southeast corner of Kansas and the southwest corner of Missouri. The area throughout which active mining has been conducted is about 45 miles long and about 5 miles wide, extending northeasterly from Commerce, Okla., to Alba, Missouri. Although the lead ores were mined on a very small scale in the vicinity of Joplin, Mo., as early as 1848, nothing of any importance was done in the district until 1870, since when both mining and smelting have been prosecuted with considerable vigor. In the beginning the lead ores only were exploited, but within a few years extensive deposits of zinc ores were found and since that time the production of zinc ore has far exceeded that of lead. Both the surface and mineral rights in Missouri and Kansas were under individual ownership by the time ore was discovered. Although some of these rights were purchased by mining companies, most of the mining has been done under leases covering small areas, usually 40 acres, although in the past many leases were given on much smaller tracts. In Oklahoma most of the mineral land had been alloted by the Government to various Indian tribes and although the title to some of these lands had been acquired by various white men before the discovery of the rich Picher field, the title to most of the land has remained with the Indian tribes and the leasing of the mineral rights has been done by the Federal Government for the benefit of the Indians. The Indian allotments were of 200 acres each and some of the mining leases covered entire allotments, although many leases were granted for only 40 acres or even less. Practically all of the leases granted in the past required the erection of a concentrating plant on each lease, a condition that has had a pronounced effect upon the mining and milling methods of the district, since the apparent ore reserves on each tract were too small to justify large and elaborate mining and milling plants. Most of the leases were

Jan 1, 1940

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By W. G. Matteson

The origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete infomation revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill1 advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,² using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the subsequent exceptional demand for fuel oil, and the resultant advance in the price of coastal crude, have been responsible for a prospecting and develop- 1 Robert T. Hill: Beaumont Oil Field with Notes on Other Oil Fields of the Texas Region. Jnl. Franklin Inst. (1902) 164, 143. 2Gilbert D. Harris: Rock Salt in Louisiana. Louisiana Geol. Survey Bull. 7 (1907) 76. ³E. Coste: Volcanic Origin of Natural Gas and Petroleum. Jnl. Canadian Min. Inst. (1903) 6, 73. 4Lee Hager: Mounds of the Southern Oil Fields. Eng. & Min. Jnl. (July 28, 1904) 78,137, 180. 6Gilbert D. Harris: Geologicel Occurrence of Rock Salt in Louisiana and East Texas. Econ. Geol. (1909) 4, 12.

Jan 1, 1921

By J. T. Eash, W. S. Crowell, E. M. Wise

The practice of dentistry, particularly the construction of artificial dentures and "bridges," involves a unique and difficult application of the precious-metal alloys. Appliances used in the mouth are continuously exposed to corrosive agencies which can hardly be described as mild, and must remain free from tarnish and be substantially immune to corrosion. Limitations with respect to space and weight demand high physical properties, while complexity of form requires ease of working. The high corrosion resistance required necessitates the use of alloys of high precious metal content. The usual expedient of resorting to mechanical working to produce the requisite strength and stiffness cannot be utilized because of the frequency of annealing and soldering operations. To meet these difficult conditions manufacturers of dental goods were early led, unknowingly perhaps, to the production of precipitation-hardening or temperable alloys. The excellent properties of iridium-platinum may have suggested the addition of platinum metals to the conventional gold-silver-copper alloys to produce greater strength and hardness. It was found that such quarternary alloys retained their high physical properties after passing through the usual soldering process; i. e., heating to 750° to 800" C. and cooling naturally in the air. Later it was discovered that they could be softened and rendered more ductile by heating to the same temperature and quenching in water. These early examples of precipitation hardening, for years the common knowledge of dental practitioners and laboratory technicians, escaped the attention of the scientific world and discovery of the transformation which was responsible for this hardening was disclosed by the Russian investigators of the system Au-Cu, Kurnakow, Schemtschushny and Zasedatelev~,(~)$ although the optimum conditions for securing good properties in aged alloys were not given attention.

Jan 1, 1932

By W. C. Maurer

A study of bit-tooth penetration, or crater forniation. under simulated borehole condirions has been made. Pressure conditions existing when drilling with air, water and mud have been sirnulated for depths of 0 to 20.000 ft. These crater tests showed that a threshold bit-tooth force must he exceeded before a crater is .formed. This thresh old force increased with both tooth dullness and diflerenrial pressure between the borehole and formalion fluids. At low differential pressures, the craters formed in a brittle manner and the cuttings were easily removed. At high differenlial pressures, the cunings were firmly held in the craters and the craters were formed by a pseudoplas-tic mechanism. With constant farce of 6,500 16 applied to the bit reeth, an increase in differential pressure (sitnulated mud drilling) from 0 to 5,000 psi reduced the crater volumes by 90 per cent. A comparable increase in hydrostatic fluid pressure (simulated water drilling) produced only a 50 per cent decrease in volutne while changes in overburden pressure (simulated air drilling) had no detectable effect on crater volume. Crater tests in unconsolidated sand subjected to differential pressure showed that high friction was present in the sand at high pressures. Similar friction belween the cuttings in craters produces the transition from brittle to pseudo plastic craters. INTRODUCTION The number of wells drilled below 15,000 ft increased from 5 in 1950 to 308 in 1964. Associated with these deep wells are low drilling rates and high costs. High bottom-hole pressures produce low drilling rates by increasing rock strength and by creating bottom-hole cleaning problems. This paper describes an experimental investigation of crater formation under bottom-hole conditions simulating air, water and mud drilling. Although numerous investigators have studied bit-tooth penetration (cratering) at atmospheric pressure conditions, only limited work has been done on cratering in rocks subjected to pressures existing in oil wells. Payne and Chippendale2 have studied cratering in rocks subjected to hydrostatic pressure using spherical penetrators. Garner et aLJ conducted crater tests in dry limestone by varying overburden pressure and borehole fluid pressure independently and using atmospheric formation-fluid pressure Gnirk and Cheathem4,5 have studied crater formation in several dry rocks subjected to equal overburden and borehole pressure and atmospheric formotion pressure. Podio and Gray studied the effect of pore fluid viscosity on crater formation using atmospheric borehole and formation-fluid pressurc and varying overburden pressure. Although these studies have provided useful information on crater formation under pressure, they were limited in that the three bottom-hole pressures could not be varied independently and, therefore, that many drilling conditions could not be simulated. The prersure chamber used in this study allowed visual observation of the cratering mechanism and independent control of the borehole, formation and confining pressures. By using different fluids in the chamber, pressure conditions existing in air, water and mud drilling to depths of 20,000 ft were simulated. The mechanisms involved in cratering at these different pressure conditions were studied for teeth of varying dullness and at different loadins rates. High-speed movies (8,000 frames/sec) and closed-circuit television were used to visually study the crater mechanism under pressure. EXPERIMENTAT PROCEDURE PRESSURE CHAMBER The Pressure chamber in Fig. I was used to simulate bottom-hole pressure conditions. This chamber has been pressure-tested to 22,500 psi and is normally operated at pressures up to 15,000 psi. The chamber contains four lucite windows' used for illuminating and observing the crater mechanism under pressurc. A closed-circuit television and a Fastax camera (8,000 frames/sec) have been used in these studies. Cylindrical rock specimens (8-in. diameter X 6-in. long) were subjected to three independently controlled pressures simulating overburden, borehole fluid and formation-fluid pressures. Overburden pressure, which corresponds to the stress induced by the overlying earth mass, was applied by exerting fluid pressure against a rubber sleeve surrounding the rock. Borehole pressure, which is the pressure exerted by the column of mud in the wellbore, was simulated by applying pressure to the fluid overlying the rock in the chamber. Formation pressure was simulated by applying pressure to the water saturating the rock. The borehole and formation pressures were equal except when mud was used in the chamber, in which case the differential pressure between these fluids acted across the mud filter cake.

Jan 1, 1966

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

The earliest U. S. patent on a crushing machine was issued in 1830. The device incorporated the drop hammer principle later used in the famous stamp mill, whose history is so intimately linked with that of the golden age of American Mining. Eli Blake invented the first successful mechanical rock-breaker --the Blake jaw crusher--patented in 1858. The idea of his mechanical principle, the powerful-toggle linkage, was so sound that today the Blake -type jaw crusher is the standard by which all jaw crushers are judged. In 1881, Philetus Gates was granted a patent on a machine which included in its design all the essential features of the modern gyra tory crusher. For some years after these pioneer machines were developed, crushing requirements were quite simple. All underground mining and open-pit quarrying was done by hand with tonnages and rock sizes generally small. In the milling of precious metal ores, stamp mills were popular as the final reduction machine. The stamps were fed with an ore size readily produced by one break through small gyratory or jaw crushers. Even in large underground mining operations, there was no demand for large crushers; and increasing tonnage requirements were met by duplicating the small units. The Homestake gold mine in South Dakota was a good example, where in 19 15 twenty -two small Gates gyratory crushers were used to prepare the ore for the batteries of 2,500 stamps. Open pit mines and the introduction of the steam shovel created a demand for larger crushers, which led to the development of a gyratory with an 18 in. (457 mm) receiving opening. Up to this time, the jaw crusher had kept pace with the gyratory, both from the standpoint of receiving opening and capacity; but now the gyratory stepped into a 15-year lead with larger and larger sizes. This trend toward large primary crushers started just before the turn of the century, and in 1910 crushers with 48 in. (1.22 m) receiving openings were being built. About this time, the jaw crusher was revived in a great contribution to primary crushing by the introduction of the 84 in. by 60 in. (2. 13 by 1. 52 m) machine. This crusher was usually followed by a 24 in. (6 10 mm) opening gyratory crusher for secondary breakage, a system which reawakened the industry to the use of the jaw crusher as a primary breaker. It is interesting that although his machines never came into general use, Thomas A. Edison ranks as a pioneer in the development of the large primary breaker. Edis on reasoned that the recoverable electrical energy

Jan 1, 1978

By D. C. Seidel, E. F. Fitzhugh

The Colorado School of Mines Research Foundation has developed a hydrometallurgical process for recovering nickel from oxidized ores, including both the iron-rich laterites and magnesium-rich, soft silicates. Known as the HSO-HTCP (Hydrothermal Sulfidization Oxidation-High Temperature Cementation in Pulp) Process, the system consists of feed preparation, sulfidization, oxidation, precipitation (cementation), and calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Nickel sulfide ores lend themselves readily to concentration before smelting or pressure leaching, but neither of the major oxidized ore types — the iron-rich laterites and magnesium-rich, soft silicates-has been directly concentrated. Upgrading of crude ore in current practice is limited to cobbing lumps of the harder, lower grade rock (protore) from the softer, enriched silicate ore, because only a small percentage of the nickel in these ores occurs in discrete, contrasting mineral particles. There is no apparent mineralogical contrast in the superficial, iron-rich lateritic ores and, in fact, there is no firm assurance that the nickel atoms are within the lattices of the limonite minerals, or else irregularly adsorbed on the limonite. Within underlying, "rotten rock" silicates, occasional veinlets of gamierite and related nickeliferous silicates are found.' The gamierite veinlets, however, are only incidental, and the majority of the nickel atoms occur as erratic replacements of magnesium atoms in the micaceous chlorites of the ore mass. Pyrometallurgical processes account for nearly all the nickel currently being recovered from oxidized ores. Plants in New Caledonia, Oregon, Japan, Brazil and Greece smelt the ores to make ferronickels or a sulfide matte,2 and the ammoniacal leaching3 at Nicaro, Cuba, is preceded by a reducing roasL4 The only fully hydrometallurgical installation has been the politically ill-fated Freeport Nickel Co. enterprise, and this process was limited to lateritic ores.5p6 A hydrometallurgical technique which might handle both laterite and the typically richer silicate ores has been an enticing goal. The technique described here was developed at the Colorado School of Mines Research Foundation, Inc. on behalf of the Republic Steel Corp. It uses sulfur, heat, air and metallic iron to recover nickel from these ores. Inasmuch as the ores are treated as aqueous slurries, the cost of drying a plant feed that normally carried 30% or more moisture is eliminated, and there are no dust problems. Patent applications have been filed by Republic Steel Corp. on the procedures used for getting the metal into solution and on the subsequent recovery without liquids-so l ids separation of the slurry. It is referred to as the HSO-HTCP Process (Hydrothermal Sulfidization Oxidation — High Temperature Cementation in Pulp). THE PROCESS FLOWSHEET The results of various experimental studies have been combined to form the continuous flowsheet illustrated in Fig. 1. This flowsheet serves as a general pattern showing the sequence of the operations which include: (1) feed preparation; (2) sulfidization; (3) oxidation; (4) precipitation (cementation); and (5) calcination and melting. This paper deals primarily with the sulfidization and oxidation phases of the process. Feed preparation: In general, the silicate ores can be considered as earthy rather than hard, and preparation might be carried out before the addition of water in a trommel, or with water in a scrubber or log washer. This breaks up the earthy particles, allowing the hard lumps to be separated by screening. The oversize material from most ores is relatively barren and may be discarded. If there is occasion to control the iron-magnesium ratio in the plant feed, laterite, which normally breaks up readily into fine sized particles, and silicates are mixed in suitable proportions. The fine product slurry from the initial steps is mixed with elemental sulfur and fed to a conventional ball mill, although the amount of actual grinding that takes place is relatively small. The object of milling is to complete the disintegration to natural particle size and to produce an intimate mixture of the ore and elemental sulfur. This pulp, which is almost entirely -200 mesh, has a pH of about 7.0 and normally can

Jan 1, 1969