Search Documents

By A. G. Suydam

Ancient as is the art of producing copper, so ancient is one of its eternal problems: refractories. Looking backward, in the light of present knowledge, clouded though it be, one cannot avoid a sense of profound respect for the patience, acumen and courage of those who have wrought so successfully despite difficulties, a more accurate understanding of which seems merely to accentuate. The problem of refractories arises from the necessity for constructing containers in which to bring natural ores into thermal solution in order to effect reduction and separation of the valuable metal content and free it of undesirable contamination while producing a waste slag. The very forces known to produce thermal solution of sufficient liquidity are necessarily destructive of exposed refractory linings in proportions varying inversely with thermal conductivity, directly with the porosity and ease of fluxing of the refractories used, and directly with the temperatures employed. Beyond this, mechanical forces are set up within the refractory lining incident to rapid heating or cooling, shrinkage at high temperatures, and unequal or excessive loading, that frequently pass the elastic limit, causing spalling or distortion. The effects of these forces are often accentuated by the necessity of providing at the same time as hot a bath and as cool a container as are consistent with fuel economy. Evolution in the Use of Refractories Clay Brick.—Fireclay and clay refractories had to yield wherever they were in contact with slags rich in basic oxides, first because of the combining power of those oxides with free silica and secondly because of the tendency of alumina to form either aluminates or alumina-silicates of varying complexity. Of no less importance, the incipient fusion point was low as compared with good clay brick of today, while the brick lacked strength at high temperatures. Expansion was slight, therefore it was difficult to make and maintain tight walls, roof, or bottom. However, the spalling tendency was low because of some of these properties and clay brick have retained their place in roasting furnaces, boiler furnace linings, and in the upper walls of some of the reverberatory types such as some refining, anode and wire-bar furnaces. They have served often and most efficiently for hot patching.

Jan 1, 1934

By T. D. Yensen

I. INTRODUCTION IT is safe to say that of all the different materials that go to make up electrical machinery, iron is the most important. Upon its -magnetic and electrical quality depends not only the efficiency of the machine but, to a very large extent, the cost. Aside from the mechanical strength, there are three characteristics of iron that are of importance in this connection, viz., magnetic hysteresis, electrical resistance, and magnetic permeability. In the homopolar machine, where the magnetic flux is unidirectional, permeability is the only important factor, but in all other machines the flux is reversed in one or more parts and causes losses due to hysteresis and eddy currents. The eddy-current loss depends largely upon the electrical resistance of the iron; the higher the resistance the lower the loss, under otherwise identical conditions. These hysteresis and eddy-current losses cause heating of the machine, and as they depend upon the magnetic density in the iron, this density must be regulated so that the heating shall not be excessive. If the hysteresis and eddy-current Josses and the permeability of the magnetic circuit will permit an increase in the magnetic density, or, in other words, a decrease in the amount of iron, this in turn will mean a decrease in the amount of copper needed, with a consequent decrease in the copper loss. It is thus seen that; indirectly as well as directly, the above characteristics have an important bearing on both the efficiency and the cost of electrical machinery. In general, it may be said that iron for electrical machinery should have the following characteristics: (1) low hysteresis loss, (2) high electrical resistance, and (3) high permeability. These are the characteristics that investigators have been striving to attain since electrical machinery first came into use.

Jan 2, 1916

By R. B. Snow

Inclusions revealed by the ultrasonic inspection of forgings, slabs, and blooms cause costly diversion or rejection of the product. Most of those inclusions are so large that they should have floated out of the liquid steel soon after teeming and been removed when the top discard was taken from the ingot. To investigate the source of the relatively large inclusions found in the body portions of ingots, a large forging ingot was examined from top to bottom along the centerline, and special studies were made of open-hearth and BOP ingots. A study of the inclusion distribution in the as-cast 134-inch-diameter forging ingot revealed only a few inclusions larger than 15 microns in the body of the ingot. Larger inclusions may be formed by entrapment of rising inclusions in large falling dendrites rather than by the precipitation and agglomeration of oxides from the liquid steel-dendrite interface during solidification. The original top crust of the ingot investigated broke away from the hot top and sank to the bottom during the solidification process, as indicated by entrapped inclusions found in a band 12-1/2 inches above the stool. A change in the hot-top insulation practice on subsequent ingots to insure the integrity of the top crust has produced clean ingots. A ZrO2 tracer was added to the hot-topping compound and to the top surface of open-hearth and BOP ingots after teeming. The tracer was found in large inclusions in slabs and blooms from these ingots. Large inclusions in the body of ingots appear to be related to disturbances of the natural freezing and shrinkage processes in the hot- top region of the ingot.

Jan 1, 1972

By Norman Pilling

THE solubilities of a series of experimental alloys covering the range 0 to 100 per cent. Ni, 0 to 30 per cent. Cr have been studied under conditions of complete submersion in several fully aerated acid solutions, and in solutions containing sulfurous acid. In nonoxidizing, hydrogen-discharging acids, if the nickel content is below a certain critical amount, chromium increases the rate of solution and nickel decreases this rate; this critical content of nickel is about 13 per cent. Alloys containing more than this corrode at a constant minimum rate independent of iron, nickel or chromium contents. Austenitic chrome-nickel steels may thus have a resistance to these acids equal to that of nickel-chromium alloys. In nitric acid and in unaerated sulfurous acid rather sharp limits of attack occur which are principally dependent on chromium content. In the former the limit of attack is not related to a particular chromium content but varies continuously with acid concentration. The action of sulfurous acid on these alloys is highly dependent on the presence of small amounts of other substances in solution, and many sulfurous acid mixtures rapidly attack alloys to which the pure acid is wholly inert. The observed effects are. not compatible with Tammann's theory relating corrosion resistance to lattice structure but are believed to be concordant with current views of the electrochemical nature of corrosion.

Jan 1, 1929

By Eldon Dunlap

RECENTLY the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a, basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occur-rence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of this indigenous water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a, conscious or unconscious correction is made for the volume of water occupying a portion of the effective pore volume of the reservoir- Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the mere fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also of interest to know whether and to what extent the presence of varying amounts of interstitial water influ-ences the permeability of the sand to oil.

Jan 1, 1938

By J. W. Leonard

One of the more obvious phenomena which relate to coke formation is that soft coals of low volatile matter content tend to yield hard or high strength cokes while hard coals of high volatile matter content tend to yield soft or low strength cokes. This observation led researchers of the Coal Research Bureau of West Virginia Univ. to study the possibility of using Hardgrove grindability as a supplemental rank indicator for coking properties. Grindability has been used for many years as a means to measure the resistance of coal to comminution but it has rarely if ever been considered for evaluating coals for carbonization. The coal proper- ties which are measured by grindability are complex, but recent work with the difficult-to-correlate high volatile coals has demonstrated that a 93% correlation exists between grindability and the total petrographic rnicrinites, exinites, and resinites. This work demonstrated that inherent ash had no apparent effect on the grindability of high volatile coals, suggesting that the coal substance is apparently harder than the associated ash. These observations, together with the patented Burstlein process," indicate that the distribution of hard and soft components in the individual high volatile coals and blends of coals may be quantitatively interrelated to coke stability through selected ranges of coal volatile matter. The objective of this progress report is 1) to demonstrate the statistical relationships which exist between coal grindability and the numerous coal petrographic entities and 2) to present the results of initial studies concerning the correlation of the coke physical strength index of stability with coal volatile matter and grindability.

Jan 3, 1964

By D. K. Atwood

Experiments resulted in a satisfactory laboratory method for restoring permeability to clay-containing cores damaged by fresh water. Clay contents of a number of field cores were measured, and permeabilities of plugs from these same cores were then deliberately reduced with fresh water. This damage is attributed to swollen and dispersed clays occupying the pore space. After damaging, a number of experiments were performed to meaJure the amount of damage and to establish some means by which permeability could be restored. The experiments included flooding the damaged cores with water-miscible fluids such as salt water, acetone, isopropyl alcohol and ethanol. Permeability was not successfully restored in these experiments. However, part of the damage was repaired by flooding with oil; when water was removed by distillation in the presence of immiscible fluids such as air or toluene, permeability was completely restored. This evidence suggested that swollen and dispersed clays could be collapsed to their original volume by strong interfacial and capillary forces. It was further postulated that the required forces could be generated by flooding the damaged cores with a solvent partially miscible with water. The flooding experiments were repeated using n-hex-an01 as the partially miscible solvent. Permeability was restored to five of six damaged cores and substantially increased in the sixth. A large fraction of the restored permeability was retained even after water saturation was raised to its original value with 12 per cent salt water. INTRODUCTION Sharp reductions in permeability often occur when relatively fresh water contacts clay-containing formations during drilling and workover operations. These permeability losses are caused by removing inorganic ions from the environment surrounding the clay, and consequent swelling and/or dispersion of clay minerals into the available pore space.' This phenomenon is generally termed clay damage, fresh-water damage, or simply formation damage; it causes large losses in current revenue by preventing oil wells from making their allowable production. Attempts to repair the damage and restore permeability by flowing salt water solutions or brines through clay-damaged cores containing montmorillonite have been unsuccessful.' This irreversibility is thought to result from formation of brush-heap, or edge-to-face, structures when the dispersed clay is flocculated. The brush-heap structures occupy much more space than the close packed domains present before damage.' One solution of the problem is to destroy the clay-water brush-heap and thus restore permeability. Because no satisfactory method existed for restoring permeability to clay-containing formations damaged by fresh water, the work described in this paper was under taken. The laboratory experiments generally consisted of deliberately damaging fresh cores containing clay and then attempting to repair this damage by various means. Results indicate that generating strong interfacial forces within the pore space of damaged cores collapses the clay brush-heap and restores permeability. These forces are most conveniently generated by flowing partially water-miscible solvents, such as n-hexanol, through a core. THEORY OF THE DAMAGE PROCESS The most common clay mineral groups known to cause permeability damage to formations are the mont-morillonites, kaolins, chlorites and illites. These clays are constructed of particles which can adsorb water on their surfaces and edges and, in the case of montmorillonite, between layers of the basic particle itself. This adsorption increases as water salinity decreases. At low salinities the particles disperse into the aqueous phase. When the clays present in the formation are kaolin, chlorite and illite, dispersion accounts completely for permeability damage to porous media. However, unlike the other clays, montmorillonite particles can imbibe water and adsorb ions between layers of sub-particles, or platelets. These platelets have net negative charges on their faces and are held together by exchangeable (or removable) cations such as Na and Ca decrease in ion concentration (salinity) in the fluid surrounding a particle causes migration of water into the clay layers and disperses the basic particle, while diffusion removes the original exchangeable ions from between the platelets. Once these ions are removed, the facing negative platelets repel each other, causing the montmorillonite to swell until, for all practical purposes, the individual platelets are dispersed. For this reason, fresh-water* damage is much more severe in sands containing montmorillonite than it is in sands containing other clays. Many investigators have shown that even trace amounts of montmorillonite can be responsible for marked reduction in the permeability of reservoir sands in the presence of fresh water." ." Monaghan and others have shown that fresh-water damage in montmorillonite-containing cores cannot be

Jan 1, 1965

By J. Donald Graham, John G. Kuhn

The goal of any development drilling program is the drilling of the exact number of holes necessary to adequately determine grade and dimensions of an ore body, no more and no less. Any technique which eliminates unnecessary drilling costs produces beneficial results, both to the company and to the person who can claim the savings. The method for controlling development drilling programs to be described was developed during the latter part of a major development drilling project at the Christmas mine of Inspiration Consolidated Copper Co. in Gila County, Arizona. It was used to test the need for drilling individual holes but could be expanded to control an entire project. Application of this method involves an evaluation of geological conditions present and a good bit of common sense. Projects involving large disseminated, rather homogeneous ore bodies of the porphyry-copper type would be the most likely candidates for application of the technique. Discontinuous ore bodies would not be amenable. The method is based on the measurement of the linear correlation between the spatial distribution of two sets

Jan 1, 1973

By A. Eilers

COMPOSITION OF CHARGES AND CONSUMPTION OF FUEL AT VARIOUS WORKS. A MARKED peculiarity of most of the smelting-works of the Far West is the looseness with which accounts of the operations are kept. Indeed, probably over half of the works do not keep any detailed accounts at all, the yearly gross statement of profit or loss being considered sufficient for all purposes. The reasons for this must apparently be sought in the as yet unsettled state of all business relations, and in the deplorable fact that only in isolated cases educated metallurgists are in charge of the smelting-works. Continual and regular assays of the ores, by-products, and slags, are almost unknown, so that it is impracticable to ascertain, even approximately, the losses in the smelting processes. Of cases where regular accounts are kept of the quantities of ore smelted, of the composition of charges, and of the fuel consumed, I know only two or three. Under these circumstances it is extremely difficult to collect figures which cover the operations for a considerable length of time, and which are so valuable for the metallurgist, who wishes to get an insight into the economy of smelting operations, as shown by practice. Figures obtained by personal observation, which can of course cover only the brief space of the visit of the travelling metallurgist, must, therefore, be made to replace the more valuable data. The writer has had occasion, during the last and the preceding summer, to visit the larger number of the Western lead-smelting works, and offers, in the following pages, such data relating to the economy of lead-smelting in the blast furnace at various works, as he has been able to obtain. The only object in doing so is to place these figures on record, so that they may be from time to time supplemented with other data, which are now wanting. I. EUREKA CONSOLIDATED COMPANY'S SMELTING-WORKS. These works smelt the ores from the mines of the same company on Ruby Hill, Eureka, Nevada. The supply is almost unlimited,

Jan 1, 1873

By Nicholas J. Grant, H. C. Chang

Microscopic observations during creep tests were made on AI-20 pet Zn, 80 pet Ni-20 pet Cr, and 25 and 3S aluminum specimens. All these materials failed in an inter-crystalline manner under certain stress and temperature conditions. Particular atten-tion was given to the initiation and propagation of intercrystalline cracks in coarsegrained AI-20 pct Zn specimens. The geometry of the grains and grain boundaries in these specimens was known before the tests. On the basis of the observations and a knowledge of the interaction between grains and grain boundaries, a mechanism of intercrystalline fracture and propagation of the fracture has been proposed. METAL, and alloy fracture occurs essentially in two ways: transcrystalline and intemrystalline. In the past most of the work done in this field was centered on the determination of stress criteria for fracture. The specimens used for these studies were tested under varying conditions of stress state, temperature, and strain rate. Unfortunately, very little attention was given to the initiation and propagation of the fracture, whereas the nature of fracture was examined closely only after failure. Several extensive reviews of these studies have been published by Orowan, Smith, Barrett, and Petch.1, 4 It is well known that a material which exhibits a ductile and transcrystalline fracture can be made to exhibit a brittle and intercrystalline fracture by modifying its composition and by heat treatment. This modification may or may not result in microscopically observable precipitation in the grain boundaries." In the creep of any one alloy the transition of transcrystalline to intercrystalline fracture is a function of stress, strain rate, and temperature." The tendency for intercrystalline fracture to occur increases as the strain rate decreases and the testing temperature increases. Extensive work on high purity aluminum (99.995 pet) under creep conditions showed the importance of the interaction between grains and grain boundaries, and the different responses of grain and grain boundaries to the variables: stress, strain rate, and temperature.7, 8 It was also shown that grain boundary deformation necessarily has to be accommodated in the grains by various deformation means as. for example, fold formation. The type of fracture resulting from the creep of high purity aluminum was invariably found to be transcrystalline. On the other hand, 2S and 3s aluminum were, under certain conditions, found to fracture in an intercrystalline manner." One reason given for this was that the grains could accommodate to a lesser extent the deformation of the grain boundaries.19 It was decided to examine this line of reasoning in greater detail and to investigate the particular interactions between grains and grain boundaries that result in the incidence and progression of inter-ct,ystalline fracture. It is also the purpose of this paper to show where and how intercrystalline cracks start and how they propagate to result in fracture. Several alloys—Al-20 pct Zn, 80 pet Ni-20 pet Cr, 2S and 3s aluminum-— were used for this study, but attention was paid mainly to the behavior of an A1-20 pet Zn alloy, since its general creep behavior has been established." From the results of this study a mechanism of intercrystalline fracture is proposed. Experimental Procedure The experimental procedure was similar to that used in previous work and has been detailed elsewhere.' Two parallel flat surfaces were milled from an originally round specimen, giving a gage portion which was 1x0.09X0.17 in. Some round specimens, 1/4 in. round by 1 in., were also tested. The A1-20 pet Zn specimens. which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar, and most of the grains occupied the whole thickness of the specimenu. Before some of the specimens were subjected to creep, the grain arrangement was mapped out in a development drawing, Fig. 1. The initiation and

Jan 1, 1957

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh. Two factors resulting from the basic flow pattern employed in gravitational classification present difficult problems for certain installations. If classification at 60 to 200 mesh of separation is desired, capacity in terms of gallons of overflow per minute per square foot of settling pool area must be low to allow required solids to settle to the underflow. If a thousand or more gal per min of feed slurry must be handled, either a very large classifier or a number of smaller units must be employed, taking up floor space and head room. Examples of this are the large classifiers, wetting tanks, or settling tanks used in the coal industry for recovery of process water from fine solids. Units as large as 50 or 60 ft in diam and 60 ft high, requiring substantial amounts of steel, are not uncommon. A second factor is the lack of self-regulation in gravitational classification. As overflow rate increases, mesh of separation increases correspond-ingly. This normally heightens difficulties of bene-ficiation. If a fine mesh of separation is required at varying feed rates, the problem is more than doubled in complexity. One of the primary advantages of gravitational classification is low power requirement. Gravity feeds or very low pressure heads are employed. However, fluid energy is still present in the inlet stream and provision must be made to dissipate it properly to obtain uniform upward or horizontal currents. Rather than waste this energy, it would be desirable to utilize it to secure a greater degree of self-regulation and simultaneously increase classification capacity per square foot of area. A free vortex could be realized by a tangential entry of feed, resulting in generation of centrifugal force to complement force of gravity in its action. With greater force it should be possible to gain finer separation at any overflow rate per square foot of settling pool area as compared with conventional gravitational classification. Furthermore, as feed rate increases, centrifugal force will also increase and at least partially offset faster currents sweeping solid particles to the overflow. A more stable classification point should result. The liquid-solid cyclone is the most common application of a free vortex in the beneficiation field.' Many previous papers have emphasized uniformity of flow pattern within the cyclone which is largely responsible for the sharp classification that can be obtained.'-4 If a free vortex can be maintained in a non-pressurized vessel with a free surface it may be possible to realize a third advantage of sharper classification. This open-top cyclone would then achieve a minimum energy loss comparable to that with conventional classifiers, and a mesh of separation coarser than 150 mesh, extending the range of application of the free vortex. This is not presently possible with ordinary cyclones. To test the applicability of the free vortex to gravitational classification, a 30-in. diameter open-top cyclone was constructed at Northwestern University. The cylindrical section was 30 in. high and the conical section included an angle of 60". The feed nozzle was a standard 4-in. pipe entering tan-gentially, with centerline 17 1/2 in. below the top of the cyclone. The conical section was flanged near

Jan 1, 1954

HAVING promised you to write concerning the nature of ores in particular, I must tell you some general facts, especially those concerning the places, kinds, and manner of their existence as well as the tools which are used. However, you must know that according to good investigators these ores are found in many parts of the world. They show themselves almost like the veins of blood in the bodies of animals, or the branches of trees spread out in different directions. Indeed, careful investigators of minerals, wishing to show by analogy how ores are located in mountains, have drawn a large tree with many branches, planted in the middle of the base of a mountain. From its principal trunk extend various branches, some thick, some slender, exactly like real trees in mature forests. They think that these grow and enlarge continually and draw themselves toward the sky, ever converting into their own nature the most disposed adjacent materials so that finally the tips arrive at the summit of the mountain and emerge with clear sign, sending forth, in place of leaves and blossoms, blue or green fumosities,* marcasites with small veins of heavy mineral, or other composition of tinctures. From these things, when they are found, it is possible to make certain inference that such a mountain contains ores, and as the signs are more or less, so are the minerals plentiful and rich or poor. For this reason the prospectors for these things take heart according to the manifestations that they find, and with hope and certainty of profit they take all possible pains to mine with skill and expense those things that the signs have indicated. Often there are ores of such a kind and quality that they raise a man in wealth to the skies. For this reason men penetrate with eyes of appraisal and judgment within the mountains and see almost exactly the places where there is ore and the

Jan 1, 1942

By E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredg-ing operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold.

Jan 1, 1937

By H. W. Seamon

THE data here given were obtained by 1500 tests made, by the United Verde Copper Co. to determine the most economical air pressure for the operation of hammer drills under the varying conditions of use, and to investigate the variation in drilling speed at different air pressures Twelve models of drills were used at gage pressures ranging from 40 to 130 lb. No effort was made to harmonize theory and practice; but rather to formulate empiric rules that would cover the. average variation of the results obtained. These rules on the performance of hammer drills, based on the air pressure as the main variable, however, are not necessarily of universal application, but they apparently satisfy the results obtained in this series of tests. The drilling conditions at this property vary widely; an average of twenty-one machine shifts to a 3-ft. (0.9-m.) round has been found necessary in some of the development work, while an, advance of 56. ft. has been made in seven shifts in the "oxide" ground. This range pre-eludes the adoption of one type of drill as a standard; consequently almost every kind of hammer drill sold in this country has been tested. At present, sixteen models are in use, of which two types of the heavy (150 to 160 lb.) mounted drills, one of the light mounted drill, one stoper, and two hand plugging drills are considered as standard.

Jan 1, 1921

By John F. Blandy

IT is not my intention in this article to consider this subject in the light of the geographer or geologist, but rather in that of the mining engineer, and to endeavor to show the necessity and value to him of studying the minor details of the field or district in which he may be engaged. It has been said by a distinguished geologist that "the natural boundaries of the geographer are rarely described by right lines. Whenever they occur, however, the geologist may look for something remarkable." And again ; " Physiognomy is no idle or doubtful science in connection with geology. The physiognomy of a country indicates almost invariably its geological character." Our country furnishes examples enough of the truth of these remarks, and in no part of it is it so beautifully illustrated as in our own State, which has been so ably described by Prof. Lesley in his admirable little work on the "Topography of Coal." As the great mountain lines become guides to the geologist in determining and mapping out the geography of the formations, so do the minor details of topography become guides to the mining engineer in conducting his explorations, discovering of dislocations, and determining the character of the deposits which are the object of his search. It is therefore requisite that he should, whilst making his surveys, pay the strictest attention to every variation of the landscape and surface of the ground. Until he has mapped out every feature he may be unable to read the geological changes which may have

Jan 1, 1873

By A. C. Fieldner, F. H. Gibson, W. A. Selvig

A foRmer paper1 described in detail various methods of calculating coal analyses to obtain the composition and calorific value of the pure coal substance—that is, of the coal free from its mineral matter. The paper included a table showing calorific values of pure coal, as calculated from float-and-sink portions, by means of the Parr formula for "unit coal" and by the customary moisture-free and ash-free formula. A modification of the Parr formula was proposed, based on the assumption that one-half the sulfur present in Coal occurs as pyritic sulfur and one-half as organic sulfur. In the published discussion of the paper Cady gave a table of results on a large number of Illinois coals as obtained by the Parr formula and the proposed modification thereof. The results obtained by Cady indicate that the Parr formula applies better to Illinois coals than does the modified formula proposed by Fieldner and Selvig. The present paper gives results obtained by applying the modified Parr formula to the analyses of the float-and-sink portions of the coals shown in the former paper, and results obtained by applying the Parr formula, the modified Parr formula, and the simple moisture-free and ash-free formula to various coals of the United States ranging in sulfur content from less than 1 per cent to more than 4 per cent sulfur. A graphic method of estimating the calorific value of pure coal and determining the relation of the coal ash to the mineral matter of coal, as proposed by Stansfield and Sutherland,2 was applied to a number of coals, and the results are given herein. Testing Formulas with Float-and-sink Separations The former paper by Fieldner and Selvig gave heat values of pure coal of the float-and-sink portions of 21 coals, as calculated by the Parr formula

Jan 1, 1932

By K. Winterton

The effect of a near-saturation unidirectional magnetic field was to decrease slightly the endurance life in Armco iron in the annealed condition. This is expected since the energy-absorbing mechanism associated with domain wall movemenfs is inhibited bv the strong field. THE factors determining failure under dynamic loading are not yet clearly recognized. One of the properties of a metal which might be thought to influence fatigue life is its damping capacity. Foppl1 conducted an alternating torsion test at a frequency of 700 cpm continuously for a period of 3 years, without the test piece breaking or showing any sign of deterioration after 1100 Million cycles of stress; the rate of dissipation of energy was sufficient to maintain the test piece at about 100°C above the ambient temperature. cazaud2 concludes from this, and others follow him, that ('the capacity for dissipation in the form of heat by internal damping is unlimited" and that therefore "damping is not directly related with fracture by fatigue." Future work may necessitate qualification of this rather uncompromising view. It is shown later that in all

Jan 1, 1960

By Jose F. Agapito

This paper describes part of a geotechnical program which was instrumental in obtaining information for the design of large oil shale pillars. The work was carried out during 1971 and 1972 in the experimental mine of the Colony Development Operation. Colony is an oil shale venture formed between Atlantic Richfield Company, Operator; The Oil Shale Corporation, Cleveland-Cliffs Iron Company, and Sohio Petroleum Company to conduct research and development in mining and retorting of oil shale. The property is located in the southern edge of the Piceance Creek Basin in northwestern Colorado, approximately 250 miles west of Denver. Mining was conducted by the room-and-pillar method in a 60-ft high portion of the Green River formation at a depth of 600 to 850 ft. Pillar dimensions are approximately 60 ft by 60 ft. The mine site is in the eastern face of the canyon containing the Middle Fork of Parachute Creek. The distance from the mine to the side of the mountain varies from 500 to 1200 ft, and its height above the stream floor is approximately 700 ft.

Jan 5, 1974

By Max W. Ball

An intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies which tend to. confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. Origin of the Law Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb.11, 1897(29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims.' . The immediate cause for the passage of this Act was stated in a brief report in the, House of Representatives (there was no debate in the Senate) to be a decision of the Department rendered Aug. 27, 1896 (Union Oil Co., 23 L. D., 223), directing the cancellation of an oil placer entry on the ground that land containing petroleum cannot be located and entered as a placer mine. The report of the Public Lands Committee of the House contains the following interesting statements Congressional Record, vol. xxix, p. 1409):

Jan 1, 1915

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964