Search Documents

By J. W. Pugh, J. D. Nisbet

F. B. Foley—The use of data published by Wever and Jellinghaus in 1931 to fix boundaries of the sigma phase in the Fe-Cr system, in the face of the author's own references to the suggestions of Bradley and Goldschmidt, Aborn and Bain, and Hougardy that the phase is much more extensive, and the very much more accurate work, which weighs heavily in favor of these suggestions, of Cook and Jones, published in 1943 and evidently disregarded by the authors, makes their derived ternary diagram, especially fig. 15 for 400°C, quite inaccurate on the Fe-Cr side and affects the extent of phase boundaries in the most controversial and important part of this ternary system. In commercial Fe-Ni-Cr alloys the occurrence of sigma has been observed time and time again at lower chromium contents than that of the 24 pct Cr, 16 pct Ni, 60 pct Fe alloy which is the lowest permitted by fig. 15 of practically carbonless metal. Newel1 reports sigma in 27 pct Cr-Fe even with some carbon present to be one of the greatest detriments to its extensive application, whereas Pugh and Nisbet set a low limit of 36 pct Cr for sigma in the binary Fe-Cr system. J. J. Heger—The diagrams presented by the authors do not agree with observations made on commercial Fe-Cr and Fe-Cr-Ni alloys, nor do they agree with two recent investigations made on the Fe-Cr and the Fe-Cr-Fe systems. I refer first to the investigation made by Cook and Jones1' on the sigma region of the Fe-Cr system. On the basis of their results which were published in 1943, Cook and Jones established new boundary limits for the sigma and the alpha plus sigma regions. These new limits have been accepted and are incorporated in the Fe-Cr diagram that appears in the 1948 edition of the Metals Handbook. This diagram is shown here as fig. 34. As will be noted, the boundary limits of the alpha plus sigma region in this diagram extend to much lower chromium contents than do those in the diagram presented by the authors in fig. 2. These new limits indicate that sigma phase should form in an Fe-Cr alloy containing 26 pct Cr, and experience with commercial alloys confirms this finding. Indeed, recent studies on a commercial Fe-Cr alloy containing 17 pct Cr have shown sigma phase to be stable in this alloy at 550°C. I recognize that the authors' work did not include studies on the sigma region; however, I believe this is a serious omission because sigma phase may profoundly affect the physical properties of these alloys and should be evaluated in any investigation which attempts to relate physical properties to the equilibrium diagram. The second investigation to which I refer is that made on the Fe-Cr-Ni system by Rees, Burns, and Cook,'' who used pure alloys and employed heating 17 W. P. Rees, B. D. Burns, and A. 3. Cook: Journal Iron and Steel Institute. (July 1949) 162, Part 3. p. 325. times that extend to 200 days. These investigators published their results in July 1949 and from these results constructed isothermal sections at 800" and 650°C. The isothermal section at 650°C is shown here as fig. 35. This diagram indicates sigma phase should form in a pure 18 pct Cr-8 pct Ni alloy. Although sigma phase has not been observed after 10,000 hr at 1200°F in commercial 18-8 alloys containing carbon and nitrogen, it has been observed under the same conditions in 18-8 alloys modified with titanium and columbium, both of which serve to reduce the effect of carbon and nitrogen. This section and the one at 800°C suggest that the constant iron sections which are presented by the authors, should be considerably altered, if they are to represent an accurate picture of the system. A few of the suggested alterations are as follows: In fig. 9, the section at 50 pct Fe, the gamma plus sigma region should be widened, not narrowed at 800" and 650°C. In fig. 10, the section at 60 pct Fe, the gamma plus sigma region should be widened at 800° and 650°C. In fig. 11, the section at 70 pct Fe, an alpha plus sigma, an alpha plus gamma plus sigma, and a gamma plus sigma region should be added. In fig. 12, the section at 80 pct Fe, the alpha plus gamma region should be widened at 800°C. In fig. 13, the section at 90 pct Fe, the alpha plus gamma region should be widened at 650° and 800°C. Undoubtedly, the chief reason for the discrepancies between the authors' data and those of Rees, Burns, and Cook is that the authors did not employ long enough heating times to allow for transformation. In this connection, I wish to warn that transformations in these alloys, particularly transformations at temperatures below 800°C, are extremely sluggish and may require a year or more to approach completion. Therefore, unless extremely long heating times are employed or steps are taken to accelerate these transformations by such means as mechanical working, the results will not yield an accurate picture of the alloy system. Certainly, an accurate picture is needed for the development of better high-temperature materials. E. J. Dulis-The purpose of this work is not clear. If an improvement of the ternary equilibrium diagram of the Fe-Cr-Ni system was wanted, it seems logical that testing techniques superior to those previously used would be a prime requirement. To approach equilibrium in this system, long holding times are needed; a fact established long ago but apparently ignored by the present authors, who used the continuous heating and cooling tests in equilibrium studies. A publication on the same system by Bradley and Goldschmidt6 was criticized by Monypenny in a

Jan 1, 1951

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of break- age in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By Waldemar Lindgren

CONTENTS. [ ] I.-CHARACTER OF THE DEPOSITS. 1. Principal Features. IN many schemes of classification and description the term contact-deposit has been somewhat loosely applied to all accumulations of useful minerals (other than those of unquestioned sedimentary origin) which are enclosed between two different rocks. As thus used, the term may include deposits of widely differing origin, and, unless qualified, is not in place in a genetic classification. The present paper deals with a special class of contact-deposits. In many geological provinces, granular igneous rocks, such as granite, diorite and syenite, have broken through and invaded sedimentary rocks. The molten magma may in part have reached the surface and there solidified with relative rapidity as a lava. The largest masses of it, however, did not reach the surface, but cooled very slowly at considerable depth under great pressure, and eventually consolidated into a rock of granitic texture. Uplifts and extensive erosion may have followed; and at the present day, in many places, thousands of feet of material have been removed, bringing to the surface the intrusive granular rocks and their once deep-seated contacts with the sedimentaries which they shattered at the time of in-

Jan 1, 1902

By Francois Clerf

IRON ORE fields are situated in both the East and West of France (see maps). The eastern deposit is by far the most important from a tonnage point of view, not only in France, but in all Europe. The ores of this region are known as minette, and are situated in the Lorraine ore fields and the Briey plateau. The iron ores of the West are those of Normandy, Anjou and Brittany. Before the war, a large number of important German companies had acquired considerable interests in these western fields and a heavy trade with Westphalia had begun. Recently, however, conditions have changed and some of the mines of Brittany and Anjou are now idle. From a geological point of view, in Anjou and Brittany, a series of synclines extends from the northwest to the southeast, containing a number of seams of varying thickness and generally intercalated in Silurian and sometimes in Devonian formations. The ore is generally a hematite or a magnetite. The composition varies from 48 to 52 per cent of iron and from 8 to 12 per cent of silica. Con¬servative estimates indicate a con¬siderable tonnage of workable ores (150,000,000 metric tons).

Jan 1, 1936

By Herbert Banks Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electrostatic separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static electricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor- generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the electrostatic separating process. Another objection made periodically is that it is generally considered necessary to feed the particles into the electrostatic field in a stream that

Jan 1, 1938

By T. E. Godson

AS this is the age of reform, a uniform mining law for North America is a moot subject for discussion at this meeting of the Institute. The question is one of peculiarly technical and, in many respects, local character. We all appreciate the value of the metal-producing industries and recognize the necessity and importance of a well-considered and evenly balanced mining law as a branch of our jurisprudence either for the Provinces or the Dominion as a whole. Mining has taken its place as a forempst industry and legislation that seeks to control and govern it is the concern of not only the active miner but the citizens of the state. A law that, through its charitable measures brings into being the prospector, the pathfinder and superstructure of all mining activity and industry! protects his interests, safeguards invested capital, and encourages and enforces development, possesses at least the salient requirements of a businesslike Act. The manner of doing so is, I think, one of local and internal concern. May I be permitted to say without presumption that of the five mining codes, or Acts, that we have in the Dominion of Canada born and bred within the Provinces of British Columbia, Ontario, Quebec, New Brunswick, and Nova Scotia, some of them could be materially improved. In many respects they do not measure up to the times; they were no -doubt creations of merit at the date of their .birth but they have not been clothed in seasonable raiment as the years passed by. It is a stern fundamental principle that all natural resources are the inalienable property of the crown. If it is mineral land, then it follows for the protection of the state and the direct advancement of the occupant that the land should be developed as such. The method or machincry by which this must be accomplished is a matter of detail, not of principle. If the right to possession as a licensee depends on discovery, it is not inconsistent with the duty the crown owes to the state that a grant in fee should pass to the discoverer if there is imposed, after patent issues, a requirement of continuous work or the alternative of an acreage tax sufficiently burdensome to make it unprofitable that the land should be held in an undeveloped state. If this requirement is recognized, the mental distinction between a grant and lease ceases to exist. A

Jan 1, 1920

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By Gregory L. Gullord

In September, 1975, production was begun at the new milling facility of ASARCO Incorporated, the Young Mill. The mill is located adjacent to the Young Mine 35 km (22 miles) east of Knoxville, Tennessee. The Young Mill replaced the obsolete Mascot Mill which had been operating since 1913. The basic flow sheet of Mascot was retained for the construction of the Young Mill, with a 20% increase in capacity included in the design. The Young Mill is capable of processing 7710 - t/d (8500 stpd) of crude ore from three underground mines (Young, Immel and Coy) yielding 300 - t/d (330 stpd) of 63% zinc concentrate. The Young Mill is unique in that 92.5% of the ore milled is recovered as saleable products, including zinc concentrate, construction aggregate, sand and agricultural limestone. Processing at the Young Mill is divided into five basic stages: two-stage crushing, heavy media separation, grinding-flotation, concentrate filtering and drying, and limestone by-products recovery. The ore bodies are located in the Knox formation, which consists of primary dolomite, secondary dolomite and limestone with silicas in the form of chert and jasperoid. The zinc mineralization occurs as an exceptionally pure sphalerite. The ore contains an occasional abundance of pyrite and traces of fluorite and barite. TWO STAGE CRUSHING Ore enters the crushing section from two points. The Young Mine ore is hoisted into a 816 ton (900 st) bin which feeds a 1.52m (60 in) conveyor via a 1.52 m (60 in) vibrating feeder. The Immel ore is trucked 10 km (6 miles) by an independent contractor and weighed on automatic recording truck scales at the entrance to the property.

Jan 1, 1977

FRank FirmstoNe, Easton, Pa.: The effect of lead on brass seems to have been recognized by Berthier, and the facts published by him as early as 1818 (Ann. des Mines, 1st ser., iii., 1818, p. 347 et seq.). He there says expressly that copper containing lead makes " dry " (see) brass, and that, for the same reason, blast-furnace

Jan 1, 1898

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

The following list comprises the names of those persons who became members during the period May 10, 1916, to June 10, 1916: ARCHIBALD, JOHN CHRISTIE, Min. Engr., Supt. of Cyanide Plant, Guanajuato Reduction Mines, Guanajuato, Mex. BRUNEL, FRANK P., Cons. Min. Engr Mitchell & Brunel, Ajo, Ariz. CALVERT, WILLIAM ROBERT, Cons. Geol. ...225 Kearns Bldg., Salt Lake City, Utah. CHAMPION, J. R., Supt The Yak Mining, Milling & Tunnel Co., Leadville, Colo. CHARLES, LAVERN JOHN, Construction Engr., Elephant Butte Dam, Elephant Butte, N. M. CHASTEL, ANDRE, Min. Engr., Societe Miniere & Metallurgique de Penarroya, 12, Place Vendome, Paris, France. CHRISTIE, WALLACE H., Vice-Pres. and Mgr., Alt. Bert Gold Dredging Co., 604 Mission St., San Francisco, Cal. CLARK, RONALD ..Hardinge Conical Mill Co., 120 Broadway, New York, N. Y.

Jan 7, 1916

Lead-zinc production in Canada accounted for 19% of the total value of metals and minerals produced in 1976, says Keith C. Hendrick, president of Noranda Sides Corp. Mine production of recoverable zinc w as 1. 158 million toils of 27.4% of free world production in 1976. Slab zinc pro¬duction was placed at 472,000 tons that year. Canadian mine production of recoverable lead was 247,000 tons or 10.6% of the free world production. Refined lead that year was at 177,000 tons.

Jan 11, 1977

By R. Stratton-Crawley

Flotation-related processes utilizing an oil phase for processing fine mineral particles have been described and various applications discussed. The problems associated with the techniques are varied, but may be summarized by the following areas; (1) applicability to fine particle beneficiation, e.g. collector extender and emulsion flotation. (2) major 'mechanical' problems, e.g. emulsion breakage and oil recovery in oil flotation. (3) complex interfacial chemistry, e.g. empirical nature of pigment flushing .

Jan 1, 1979

By P. R. Bradley

NO thought had been given to deep level mining at the Alaska Juneau mine prior to 1930, but in that year a prospect winze was started and continued for 1000 ft. vertically below the main haulage or adit level. The point at which this winze was started was selected entirely by the prevailing physical conditions, such as proximity to established workings, convenience, and the presence overhead of a substantial pillar of dimensions sufficient to lo¬cate the sheave wheel and loading pocket. It was, therefore, with some surprise that the unusually high-grade ore found just below the collar of the winze persisted, with certain vari¬ations, to a full depth of 1000 ft. vertically. Likewise this unusually high-grade ore was found to persist on the various crosscuts driven on levels at 200-ft. vertical intervals. To be brief, this deep level work found richer ore than any yet found in the mine over like areas, and inasmuch as the area was sufficient to plan for extensive deep level mining, plans for such work were given extended consideration.

Jan 1, 1936

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960's, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

PORPHYRY mining in the Bisbee district in Arizona did not begin until 1923, though Bisbee had been the scene of profitable copper-mining operations since 1880, and during the interval had contributed roughly 2,000,000,000 lb. of copper to the world's supply. At that time it ranked third among the copper districts of the United States, first place for total production going to Butte, Montana, and second to the district centering around Calumet, Michigan. Bisbee's production had come from the so-called "limestone" mines operated principally by the Phelps Dodge Corporation and the Calumet & Arizona Mining Co. Each of these companies had a large smelting plant at Douglas, 25 miles southeast of Bisbee on the Mexican border. The town of Douglas owed its existence primarily to the copper mines of Bisbee, the particular location having been determined, first, by the fact that water in adequate supply could be obtained by sinking wells; and, second, by its position about equally distant from Bisbee and the mines in Sonora, Mexico, of the Moctezuma Copper Co., a Phelps Dodge subsidiary. Three partners, Martin, Reilly, and Ballard, conducted the first operations of consequence at Bisbee about 1880; and in 1881 a smelting plant consisting of two 36 in. water-jacketed blast furnaces was erected near by. The ore came from open-cut workings on the later-to-be-famous Queen orebody. The furnace charge is said to have averaged 23 per cent copper-twice as rich as the concentrates from the mills and four times as rich as the smelting ore shipped from Bisbee in recent years. As early as 1881, disputes arose among owners of various claims, and groups of claims, over the ownership of orebodies under the law of apex and extra-lateral rights. This law gives a miner the right to follow his vein downward on its dip, even

Jan 1, 1933

By Richard McCaffery

CONTENTS PAGE 1. Research on Blast-furnace Slags (A Progress Report). By Richard S. McCaffery 5 2. Determination of Viscosity of Iron Blast-furnace Slags. By Richard S. McCaffery, Clarence H. Lorig, Ira N. Goff, Joseph F. Oesterle and Oscar O. Fritsche 27 3. Effect of Magnesia on Slag Viscosity. By Richard S. McCaffery, Joseph F. Oesterle and Oscar O. Fritsche 55

Jan 1, 1931

THE CHAIRMAN (H. W. MORSE, Los Angeles, Cal.).-I would like to open this meeting for a little while to the general subject of leaching. We ought not to hold back if we have any new schemes for the future. I know that those of us who are tangled up with this lei thing work will appreciate any suggestions that will make us work harder and, scheme, harder to pull through these past difficulties on leaching. F. S. SCHIMERKA, Clifton, Ariz.-Under the direction of J. W. Bennie, General Manager of the Shannon Copper Co., Clifton, Ariz., 'it has been my valued privilege to cooperate in the elaboration of a hydrometallurgical process aiming at the recovery of copper in mill tailing resulting from a gravity concentration of a low-grade semi-oxidized sulphide ore occurring in a porphyritic gangue. The experimental work which has been carried on with a 25-ton plant is completed, and the company is building at present a leaching plant on a larger scale, the first unit consisting of a 150-ton roasting furnace and accessories for leaching the calcine.

Jan 12, 1916