Search Documents

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

Discussion of the paper of FRANCIS S. PEABODY, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 125, May, 1917, pp. 775 to 781. THE CHAIRMAN (CARL SCHOLZ, Chicago, I11.).-Coal wastage is undoubtedly one of the most prominent topics before the coal operators of the United States today. Even those who have been in the business only 25 years, like myself, know that the exhaustion of coal is something that should and must, be curbed. If it is not, before long we shall discover that the great coal resources of the country are not what we-thought they were; we have been so accustomed to work at the best and thickest coal alone, that it will be difficult for us to realize one of these clays-and that (lay is not far distant-that we are no longer the rich nation in coal that we thought we. were. In this connection I feel obliged to attach a little blame to the Geological Survey for misleading the people. There are several members ,here who assisted in that work, and I am going to ask them to defend themselves. The Geological Survey deals with coal seams of much less thickness than we could now expect to, mine, particularly with the present high wages, excepting at a prohibitive cost. The Geological Survey, in its estimates, does not discriminate between thick and thin seams, but simply estimates our resources at so many hundred thousand billion tons of coal. I believe they include seams from 15 to 18 in thick, but you all know that a vein below 3.5 or 4 ft. is not considered economical to mine at this time. R. V. NORRIS, Wilkes-Barre, Pa.-Mr. Peabody has evidently been thinking almost entirely of Illinois conditions, with which I regret to say I am absolutely unfamiliar. In some West Virginia mines the total recovery at present is considerably over 90 per cent. and extraction-, as high as 97 or 98 per cent. are claimed.

Jan 1, 1918

By Robert Forsyth

As the latest plant on a large scale, the new Bessemer works of the North Chicago Rolling Mill Company, at South Chicago, presents some features of interest to steel-makers, I have ventured to lay before the Institute a short description of that plant, and some* remarks upon the practice there. At the time the South Chicago works were designed the adoption of the basic process in this country seemed imminent. Experience in Europe had demonstrated the perfect success of the process technically, and the question of its commercial value was one which, for any particular works, would have to be settled by its special advantages for procuring the necessary ores and basic materials. Under the circumstances, it was thought best at South Chicago to so arrange the plant as to allow the introdnction of the basic whenever it became advisable, and to make such other changes from the standard type of Bessemer plant as the state of the art seemed to demand and to foreshadow. As the use of metal direct from the blast furnace, while generally condemned by experts here, was in such successful practice in Europe (particularly in connection with the basic process), there was no doubt about its feasibility, while its economy in fuel and labor made it especially attractive to the Western manufacturer. It was accordingly decided to build a direct-metal plant adapted to the basic process. The ingots made were to be rolled into rails at one heat, and were to be of such size (12 inches square and long enough for three and four rails) as to be readily and quickly handled by the rolling machinery proposed. This small size of ingots, and the large number cast from each heat of 10 tons, made it necessary to provide a good deal of room in the casting-pit—much more than in any previons plant—and to put down extra facilities for handling ingots. To meet the delays incident to the basic process—to insure that one vessel should be always blowing if necessary, and to provide opportunity for current repairs to linings, etc.—it was decided that three vessels should be used, and, to properly concentrate the work of

Jan 1, 1884

By L.W. Eastwood, Arthur E. Bousu, C. T. Eddy

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Thomas C. Wilder, Walter E. Galin

Measurements of the electromotive force of the cell at 995°C have shown that the cell may be used to detennine the zinc content of molten Cu-Zn alloys to the nearest 0.05 wt pct. The cell is used for brass melts to which no ZnO is added intentionally, because essentially all oxygen in the Cu-Zn-O system is present in the form of ZnO. The cell is also used to detev,nine the thernodynamic activity of zinc for Cu-Zn al1oys of the brass composition range, from which the equilibrium partial pressure of zinc for such alloy may also be calculated. The electrochemical measurement of the concentration of the most active metal in other engneering- alloy systems by a similar technique is also considered. IN recent years there have been many studies concerning the direct electrochemical measurement of oxygen content in molten engineering metals.' These investigations employ galvanic cells in which the electrolytes are various solid mixed-oxides which conduct current by movement of oxide ion vacancies under the influence of an oxygen potential gradient. Similar cells have also been used to measure the thermodynamic properties of mixing of solid alloys,' one component of which has a much greater affinity for oxygen than the other component(s). One alloy system of obvious engineering importance comprised of two metals of greatly differing affinity for oxygen is copper-zinc. At the casting temperature of molten brasses, the zinc concentration is very difficult to control not only because its vapor pressure is very high, but also because of its high affinity for oxygen to form ZnO. Inasmuch as brass castings may be required to have a zinc concentration within very narrow limits, it would be advantageous for the brass industry to have a means for quickly measuring the zinc content in the molten alloy just prior to pouring. A calculation based on earlier thermodynamic studies of oxygen and zinc in dilute solution in binary Cu-O and CU-Z' alloys indicates that the oxygen concentration of molten 70 wt pct Cu-30 wt pct Zn brass must be much less than 1 ppm for the separate phase ZnO not to exist in the ternary Cu-Zn-O system. Thus it can be assumed that all molten brasses, both in the laboratory and in the foundry, are sufficiently saturated with oxygen for the separate phase ZnO to be present. In view of the foregoing reasons, the cell investigated at 995°C for the purpose of measuring the zinc concentration in molten copper-zinc alloys, particularly those of brass compositions. In this cell the left hand electrode is a reference electrode comprised of a mixture of the pure powders of nickel and nickel oxide, to which a platinum contact is made. The electrode of interest is a molten Cu-Zn alloy of unknown zinc concentration with a tantalum wire contact. The electrolyte is the commercially available (Zircoa) calcia stabilized zirconia. The ZnO in the Cu-Zn electrode compartment is not intentionally added, but is naturally present as a result of the infinitesimal amount of oxygen required for its formation in this alloy system. In cell [A] nickel oxide is reduced at the cathode where O= represents the electrolyte. At the anode dissolved zinc of the Cu-Zn alloy is oxidized to form ZnO(s) in its standard state Thus the overall reaction is for which the molar free energy change is where 5 is the Faraday equivalent (23,063 cal per v equivalent), is the electromotive force of the cell in volts after correction for the Pt-Ta thermocouple, FOf (ZO) and AFF (NO) are the standard molar free energies of formation of the respective oxides, and a2n is the thermodynamic activity of zinc in the molten Cu-Zn alloy. The reference state of zinc in this case is taken to be the pure liquid. At constant temperature all the terms of Eq. [I] are constant except and azn Thus since all other participants in the electrochemical reaction are in their standard states, the change in the electromotive force of Cell [A] is represented only by a change of the thermodynamic activity of zinc at constant temperature. The zinc concentration is related to the activity by sampling the alloy for chemical analysis after cell measurements are taken. EXPERIMENTAL A typical cell construction is shown in Fig. 1. This and other experimental details were similar to that described earlier with the exception of some minor modifications which are detailed below.

Jan 1, 1970

By John D. Ridge

For mining geologists, the most important trends during 1962 have been the increased concentration of the exploratory activities of American mining companies in the United States and Canada and the greater use of the combined techniques of geology, geophysics and geochemistry in searches over larger areas for wider varieties of metals and minerals. The principal reasons for these changes in approach have been the deterioration of the political-economic climate in many areas of the globe of equal or greater geologic promise and the realization that modern exploration is most efficiently and economically conducted through the use of all available means of detecting ores in areas sufficiently large to raise to a maximum the chances of success. The attitude of certain major U.S. metal-producing companies can be shown by the officially ex- pressed positions of their principal officers. Early in 1962, Clyde E. Weed, Chairman of the Board of Anaconda, remarked that "because of unsettled conditions and disruptive influences in many of the copper-producing areas of the world, it is imperative that domestic copper-producing capacity be improved and made as efficient as possible in order to meet consumer demands at reasonably stable prices." In November, Robert G. Page, President of Phelps Dodge, pointed out that his company is not only concentrating most of its exploratory effort on this continent but is also increasing the number of metals for which it is searching. Frank R. Milliken, President of Kennecott, recently said that "most of our exploration money is going into the northern part of the Western Hemisphere."

Jan 2, 1963

By K. Mukherjee

A quasi-thermodynamic calculation is presented for estirt~ating vacancy Parameters in fcc metals. For fcc metals the equilibrium vacancy concentration at the melting point can be approximated by a constant mole fraction. The Gibbs free energy of formation of the vacancies can then be expressed as a simple function of the absolute melting temperature alone. From this description the formation energy Ef, the vibrational entropy Sv, and the formation volume of a vacancy can be calculated in terms of known thermodynamic parameters. The calculated values are in good agree-rnent with available experimental results. IT appears that many of the physical parameters associated with lattice defects can be empirically related to thermodynamic melting parameters.'-7 Besides the implicit correlations between melting phenomenon and point defects, the melting temperature itself at atmospheric pressure can be used as a reference temperature for the purpose of comparison of vacancy concentrations in a given crystal class. The concentration at the melting point then corresponds to the maximum vacancy super saturation in the crystalline state at a fixed pressure. For pure fcc metals such as Au, Cu, Al, Ag, Pb, and Pt the mole fraction of vacancies at the melting point8 is of the order of 10*"3 to 10"1. The equation expressing the equilibrium vacancy concentration at the melting point contains three parameters: the formation energy, the vibrational entropy, and the absolute melting temperature, see Eq. [2]. Since these three parameters cover a wide range of values8 in the above-mentioned metals, it can be assumed that in other fcc metals, for which no reliable data are available, the mole fraction of vacancies at the melting point most likely lies in the range 10~3 to lO"4. This is then the basis of the calculations described in this article. Within this range the mixing entropy can be linearized and the vibrational entropy, the formation energy, and the vacancy formation volume can be calculated in terms of known thermodynamic constants. 1} LINEARIZATION OF MIXING ENTROPY The Helmholtz free energy of a crystal containing n vacancies at the melting point can be writteng as where Ef, T,, k, and S, are the formation energy of a vacancy, the absolute melting temperature, Boltz-mann's constant, and the vacancy formation entropy, respectively. After applying Stirling's approximation in Eq. [l] and minimizing with respect to n where (n/N), is the equilibrium vacancy concentration in mole fraction at the melting temperature at 1 atm pressure. If instead of setting (6~/6n) = 0 immediately after Stirling's approximation in Eq. [I], the configurational partition function is simplified, then some useful and significant results can be obtained by utilizing the experimental inforrnation After applying Stirling's approximation and rearranging is plotted as a function of (n/N) in Fig. 1. The points, not all of which are shown, are fitted by a straight line substituting from Eq. [5] into Eq. [I] and minimizing with respect to n combining Eqs. [6] and [2] It must be emphasized that Eq. [7] is only a crude approximation based on an oversimplified model of

Jan 1, 1967

By F. R. Brotzen, L. D. Whitmire

Single crystals of high-purity molybdenum were de-formed at temperatures from 195°to 473°K, and the effect of deformation on the electrical resistivily was deler-mined. To separale the resislivity components of point and line defecls some cryslals were annealed at 473°K. The vale of resislivily increase wilh strain was nearly linear and was strongly dependent upon the deformation temperature. Point dejects are annealed out without any effect on the flow stress. At low temperatures the flow stress is a linear function of the square root of the resistivity increase attributable to dislocations. ELECTRICAL-resistivity measurements have been used successfully to gain information on structural changes in metallic materials. During plastic deformation the electrical resistivity rises because of electron scattering from newly created lattice defects. Such measurements lend themselves, therefore, to corroborating results from direct observation of lattice defects and, to a certain extent, to correlating defect densities and distribution with mechanical properties. Published information on research with single crystals of the bcc metals of Group VI, particularly molybdenum, is still limited. Yet, molybdenum single crystals of relatively high purity can be readily prepared by electron-beam-melting techniques. Furthermore, some valuable information on the defect structure of deformed crystals by direct observation is available. Lawley and Gaigher,1 for example, have examined dislocation configurations in deformed molybdenum crystals by means of transmission electron microscopy. Their results revealed that the dislocation density and distribution were strongly dependent upon the deformation temperature. These findings differed from those by Keh and weissmann,2 who found that the average dislocation density in polycrystalline iron deformed between 138° and 298°K depended only on the degree of strain and not on the deformation temperature. Martin3 and peiffer4 showed that point defects introduced in polycrystalline molybdenum by cold work can be eliminated by annealing at a relatively low tempera-ture. In view of their work it became apparent that resistivity measurements of suitably annealed crystals could disclose changes in their dislocation structure and contribute to the understanding of the work hardening of molybdenum crystals. EXPERIMENTAL PROCEDURE Crystals were grown by electron-beam zone melting5,6 of 0.062-in.-diam molybdenum rods (99.99 pct) supplied by General Electric Lamp and Wire Division, Dover, Ohio. The crystals, about 4 in. long, were prepared by using five zone-refining passes at a speed of about 6 mm per min in a vacuum of about 5 X l0-6 Torr. The resistivity ratio of the crystal, p(4.Z°K)/p(273°K), was generally near 10-3. These crystals were used as tensile specimens of uniform diameter in the "as-grown" condition. They were oriented for maximum shear on the (011)[111] slip system (Schmid factor >0.49). The specimens were held in spherically seated Templin-type grips so as to minimize bending. Samples were deformed on an Instron machine at a strain rate of about 5 X 10-5 sec-1 in an isopentane bath with dry ice at 195°K, in ice water at 273°K, and in a vegetable-oil thermostat at 373° and 473°K. The temperature in the latter was maintained constant within +2°K. Resistance measurements were carried out with a Kelvin double bridge. The resistance of the potential leads was kept low by using large-diameter wires outside the low-temperature bath. Many of the resistance data were checked by measurements made with an ac bridge. Current and potential leads were spot-welded to the specimens. The distance between the potential leads, about 3 in., was also considered to be the gage length for the strain measurements. Diameter and gage length of the samples were measured optically with an error of less than 2 pct. These measurements were used also to insure that the deformation had been uniform over the gage length of the specimen. Resistivity changes were then determined from the resistance measurements at 4.2°K assuming constancy of volume. In the course of a test, the crystal diameter, gage length, and resistance at 4.2°K were determined first in the initial state and subsequently for various amounts of elongation.

Jan 1, 1968

By E. S. Hutchinson

The subject of the influence of coal-dust in mine-explosions has received considerable attention both in England and on the continent of Europe, but until the recent disaster at Pocahontas, Va., it seems not to have been of special interest to engineers in this country. The reason, perhaps, is that most of our bituminous mines are worked by short shafts, slopes and drifts; few have been specially dry; and the explosions that have occurred could readily be traced to fire-damp with 110 complicated circumstances. The object of the present paper is to bring together, for the convenience of members of the Institute, the principal English opinions upon this important subject. Messrs. Lyell and Faraday, in their report to the Home Secretary," in England, on the Haswell Colliery explosion in 1844, seem to have been the first to point out that dust fed the flame originating in a

Jan 1, 1885

THE slag performs two useful functions. in open-hearth steel-making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) SO2, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (SiO2 and P2O5). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined, and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1951

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

The following is an incomplete list of members and guests who called at Institute headquarters during. the period Mar. 10, 1919,. to Apr. 10, 1919. F. T. Agthe, Hannibal, Mo. Jay Lonergan,. Denver, Colo. W. F. Almy, Canada. R. R. London, Cebu, P. I. P. G. Bandy, Mexico. W. D. Mainwaring, Philadelphia, Pa. H. R. Bank, Humboldt, Ariz. _ W. G. Mitchell, Montreal, Can. Alan M. Bateman, New Haven, Conn. Francis Nicholson, Joplin, Mo. C. A. Brooks, Lead, S. Dak: C. H. Palmer, Los Angeles, Calif. Louis J. Brunel, Oakland, Calif. D. A. Powell, Columbus, Ohio. W. Burns, Sante Fe, N. M. W. H. Reber, Dallas, Tex. J. B. Carlock, Major, 1st Gas Regt. Capt. J. B. Richards, Spokane, Wash. Louis S. Cates, Hayden, Ariz. T. C. Roberts, E. Orange, N. J. W. M. Corse, Mansfield, Ohio Max Roesler, Washington, D. C. E. 0. Daue, Philadelphia, Pa. C. 0. Sanford, Los-Angeles, Calif. John Davenport, W. Norfolk, Va. Gustave Sessinghaus, Denver, Colo. James T. Dixon, London, England, . E. H. Shriver, Milford Center, Ohio. S. K. Dahl, Messina, Transvaal, S. Af. H. M. Spoor. W. G. Eberhardt, Tucson, Ariz. W. H. Staver, New York. H. S. Emlaw, Grant Haven, Mich. D. B. Sterrett, Washington, D. C. I. W. Farrand, Camp Merritt. W. G. Swart, Duluth, Minn. Oscar Gotsch, Jr., St. Louis, Mo. A. W. Stickney, London, England. James 0. Greenan, Oakland, Calif. E. C. Templeton, Downey, Calif. Gilbert Hart, Philadelphia, Pa. . . R. T. Walker, Pioche, Nev. K. L. Hsueh, China. A. T. Ward, Bellefonte, Pa. Zay Jeffries, Cleveland, Ohio. Joel H. Watkins, Washington, D. C. R. W. Kern, Verde, Ariz. J. Wertheimer, Cleveland, Ohio. H. D..Kinney, Easton, Pa. C. R. Wilfley, Ouray, Colo. E. L. Lasier, Washington, D. C. J. P. Wood, Engrs., U. S. A. Carl Zapffe, Brainerd, Minn. Leland D. Adams has left the employ of the Weedon Mining Co., Ltd., at Montreal, Quebec, and is going to Oakland, Calif., where his address will be 1180 Mandana Boulevard.

Jan 5, 1919

By Leo Horvitz

PETROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer1 in Germany and by Sokolov2 in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas.

Jan 12, 1954

By James Douglas

The development of the copper-resources of this country has kept close pace with the unfolding of its geographical area to commerce. In colonial days, when our English ancestors occupied only the Atlantic seaboard, insignificant quantities of copper were mined in Connecticut, New Jersey, and Pennsylvania, and the ore was shipped for treatment to England. The first steam pumping-equipment

Jan 1, 1891

By John C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert, Russell, Le Conte, Spur, Louderback, and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea.

Jan 3, 1960

By Arthur B. Foote

Ore production from the property of the Miami Copper Co. began early in 1911. Until 1925 this ore came from the so-called high-grade orebodies, which contained a little over 2 per cent. copper. This ore was mined by the following methods: 1. Top slicing after mining the peaks by square setting, which produced 4,524,347 tons, including ore from square setting. 2. Shrinkage stoping with sublevel caving of the pillars, which produced 2,230,577 tons. 3. Undercut caving with hand tramming, which produced 15,427,672 tons. Estimating December tonnage, the total ore mined to the end of 1929 will amount to slightly more than 43,000,000 tons. The first method was described by E. G. Deane' and the second by D. B. Scott,' and the third, together with a general description of the mine, by J. H. Hensley, Jr.' The geology of the district has been worked out by Dr. F. L. Ransome.2 The author acknowledges also the assistance of R. W. Hughes, assistant mine superintendent, E. V. Graybeal, chief mine engineer, A. J. McDermid and S. R. Burdick, engineers of Miami Copper Co., Miami, Arizona. Factors Influencing Selection of Mining Methods The mining method described herein was selected primarily with a low mining cost in view and was developed to avoid as far as possible dilution of the already very low-grade ore. In 1924, with the exhaustion of the high-grade orebodies in sight, it was decided to develop the low-grade orebody, which at that time contained 36,000,000 tons of ore assaying 1.06 per cent. copper, and had an area of 50 acres with an average thickness of 206 ft. overlain by an average thickness of 320 ft. of barren capping.

Jan 1, 1930

By E. M. Wise, T. E. Kihlgren, N. B. Pilling

SYSTEMATIC data are presented on the relation of composition of nickel silvers to color, tarnish resistance, hardness and liquidus temperatures, for alloys containing up to 30 per cent nickel and 50 per cent zinc, further modified at certain nickel and zinc contents by 0 to 8 per cent of tin and 0 to 10 per cent of lead. Attention has also been directed, using a still more limited range of alloys, toward a study of tensile properties and such casting properties and characteristics as fluidity, shrinkage and pressure tightness. In some of these, rather broad ranges of composition are dealt with; in others, it has been expedient to focus attention on the Federal Specification 20 per cent nickel silver casting alloy, WWP-541.

Jan 1, 1935

By A. M. Gaudin

A great number of hypotheses has been advanced to explain the complex phenomena that are encountered in flotation. In the days of bulk-oil flotation, when a large quantity of oil was employed, it was observed that the oil-mineral aggregate floated above the ore-pulp because of its lesser density. With the advent of froth-flotation this phase of the theory had to be modified to take into account the presence of air bubbles. The reason why the mineral-bearing froth of today rises to the top of flotation cells is, of course, because the air-mineral aggregate, with whatever reagent may be associated with it, is lighter than the pulp. In an attempt to explain froth-flotation the fact has been emphasized that certain minerals are wetted and therefore remain in water; while others are not wetted and therefore become associated in preference with air. Such an "explanation" does not explain facts, it merely states them; for instance, it does not explain why minerals are wetted under some circumstances and not wetted under others. Going somewhat further, the wetting or nonwetting of minerals by water has been ascribed' to differences in the angles of contact between oil droplets and mineral surface at the surface of the minerals. This explanation, however, was abandoned when soluble flotation reagents came to replace the so-called "insoluble" reagents. Another theory, sponsored about 10 years ago by Ralston,² involves the effects of electric charges at the surface of the mineral particles and air bubbles. This theory, unfortunately, was not developed as fully as it seems desirable. The belief that adsorption phenomena might play a preponderant role in flotation3 has been rather widespread for the last 10 years. Unfor-

Jan 1, 1928

By J. L. Whitlock

An attached growth aerobic biological treatment process has been developed at Homestake Mining Co.'s Lead operation which not only oxidizes free and complexed cyanides, including the stable iron complexed cyanides, but also thiocyanate, and the oxidation byproduct ammonia. Through the employment of a mutant strain of bacteria which has been gradually and specifically acclimated to the waste, these potential pollutants are mineralized to relatively harmless sulfates, carbonates, and nitrates. The resultant effluent, through toxicological testing, has been shown compatible with the receiving stream, which serves as a cold water marginal trout fishery.

Jan 1, 1985