Search Documents

By J. Steininger

The Hallimond tube flotation of sphalerite and pyrite with sulfhydryl collectors has been found to be inhibited near neutral pH in the presence of copper salts. Alkalimetric titration studies of the reactions between collector and activator indicate that this effect is apparently related to the formation of basic copper collector complexes. The conditions of formation of these compounds and their stability are in good agreement with the depression observed in flotation experiments. The general procedure employed in the flotation of zinc sulfide minerals requires activation of the mineral surface by heavy metal ions, usually copper, which react more easily than zinc with the common short-chain ionic sulfhydryl collectors.' Commercially, zinc flotation is carried out under alkaline conditions (pH 7 to 10.5), but small-scale experiments indicate that zinc sulfide minerals can also be activated and collected under acid conditions. Selectivity, however, becomes poor at low pH and undesirable materials such as pyrite, silicates and carbonates tend to report in the float. Several years ago, Wark and Sutherland~, measured the contact angles of air bubbles on copper-activated sphalerite immersed in various sulfhydryl collector solutions. When represented, as in Fig. 1, on pH-sodium cyanide diagrams, the results are characterized by 'islands' of non-contact near neutral pH and

Jan 1, 1969

By W. C. Phalen

INTRODUCTION NOBODY will dispute the fact that the conservation in every legitimate manner of our valuable high-grade phosphate-rock deposits is a present-day problem of importance. The table and curve, given herewith, show. that during the past 10 years the exportation of high-grade rock has averaged very close to half the total output of the entire country. The bulk of this exportation is from Florida, for obvious reasons. It is plain that the deposits in this State, more particularly, are being wastefully depleted under a system of selecting the cream of the product for exportation to Europe, leaving the comparatively low-grade rock, running from 65 to 70 per cent., and under, in bone phosphate of lime, for our own n fertilizer manufacturers to work up when all the best rock is gone. In this paper the writer has endeavored to make a point of describing in some detail the important methods of production and conservation in Tennessee. These ought to prove of educational value to our American agriculturists and fertilizer manufacturers, and should result in a demand for the highest-grade rock, both for direct application to the soil and for use in making acid phosphate. It is certainly evident that the European

Jan 10, 1916

P. Herasymenko (New York University, New York) —The authors' experiments on equilibria between water vapor and liquid synthetic slags represent a valuable contribution to our knowledge of the nature of liquid slags. They can be regarded as a proof of ionic splitting of water molecules dissolved in slags. The assumption that water dissolved in slag was com- pletely ionized was made in my report on hydrogen equilibria in steelmaking as early as 194010. In that paper, the first systematic data were given on the content of ionized hydrogen in acid and basic open-hearth slags. The paper probably escaped the notice of the authors, although they mention the articles published later by other investigators who reported erratic and

Jan 1, 1958

By John Chipman, Carl F. Floe

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Carl F. Floe, John Chipman

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

Flaubert, as we know, laid stress on the selection of the right word, le mot juste, the precise epithet, the word that belongs to the thing. A sentence, or even a paragraph, may be spoiled. by the use of a word that is not proper, that does not fit or is foreign to the meaning intended. An Australian mining expert is reported to have said: You have a property of considerable value, and what I saw warrants s good development of very rich cubicular galena, with gossan intermixed. 'Cubicular' means 'belonging to a small bedroom', a 'cubicle' being a sleeping compartment. He meant 'cubic', of course. This is a malapropism, and reminds me of the lady from Chicago that, on her return from Europe, said how much she had enjoyed the rural parts of France, because, among other things, it was "so delightful to hear the French pheasants singing the mayonnaise to the tune of the Los Angelus". It is impossible to amalgamate coal-tar thoroughly with the pulp in the agitating-tank. In metallurgy, 'amalgamate' refers to the combination of mercury with one or both of the precious metals, forming an amalgam, which is an alloy of mercury with another metal. It differs from other alloys, such as brass or bronze, in being made without the aid of heat, inasmuch as mercury is molten at the ordinary temperature. The word comes to us from the Greek through Old French and means 'something soft'. It is a mistake to use technical terms, having a specific meaning, for purposes that are foreign to that meaning. The writer of the quotation is not discussing any combination of metals; he is dealing with the physical process of mixing and is using 'amal-

Jan 1, 1931

By W. A. Krivsky, R. Schuhmann

PREVIOUS papers in this series on the thermo-•t dynamics of copper-smelting systems have presented a survey of the field and an outline of the overall program: thermodynamic studies of iron silicate slags, 2-4 and thermodynamic data for simple mattes in the Cu-S system.5 Since this program was started, an excellent summary of the whole field of physical chemistry of copper smelting was published by Ruddle. The present paper represents a further step in the study of liquid mattes, and deals specifically with the Cu-Fe-S system. The importance of the Cu-Fe-S system to copper smelting is evident from the fact that these three elements constitute 90 to 99 pct of the totalweight of most commercial mattes. In copper mattes oxygen is an important fourth component. Oxygen was rigorously excluded in the work to be described in this paper. However, the behavior of oxygen in mattes was the subject of a companion research by Lander' which will be described in a subsequent publication. Several studies have been made previously of phase equilibria in the Cu-Fe-S system,8-10 so that the ternary phase diagram is fairly well established in most regions. Also, separate studies have been made of the phase diagrams and thermodynamic properties for the three binary systems: CU-S,5,12-15 CU-Fe,11,14,17 and FeS.11,14,16,17 However, no work has

Jan 1, 1958

CONTENTS PAGE BARTON, D. C.-The Eötvös Torsion Balance Method of mapping Geologic Structure (T. P. No. 50) 1 GEORGE, P. W.-Experiments with Eötvös Torsion Balance in the Tri-State Zinc and Lead District (T. P. No. 65). 15 LANCASTER-JONES, E.-The Computation of Eötvös Gravity Effects (T. P. No.75) HEILAND, C. A.-A Cartographic Correction for the Eötvös Torsion Balance-(T. P. No. 52) 17 SLICHTER; L. B.-Certain Aspects of Magnetic Surveying (T. P. No. 120). . . . 18 WEAVER, W.-Certain Applications of the Surface Potential Method (T. P. No.121) LUNDBERG, H.-Recent Results in Electrical Prospecting for Ore (T. P. No. 98). . 20 HOTCHKISS, W. 0., ROONEY, W. J. and FISHER, J.-Earth-resistivity Measure-ments in the Lake Superior Copper Country (T. P. No. 82) 21 LEONARDON, E. G. and KELLY, S. F.-Some Applications of Potential Methods to Structural Studies (T. P. No. 115) 23 MASON, M.-Geophysical Exploration for Ores (T. P. No. 45) 25 The Eötvös. Torsion Balance Method of Mapping Geologic Structure Discussion of the paper of D. C.. Barton, issued as Technical Publication No. 50 with Mining and, Metallurgy, February, 1928. D. C. BARTON.-The field surveys which I have been privileged to use as illustrations for this paper were done for Mr. DeGolyer's companies and were released through his favor. W. J. MILLARD, Tulsa, Okla.-Has any oil been found by the torsion balance in West Texas? D. C. BARTON.-NO new oilfield has been discovered on the basis of torsion balance work. It has had some part in controlling the policy of certain companies in playing the extension of known oil fields. A number of "T. B." structures have been drilled and dry holes obtained. Of those known to the writer, one apparently was a structural high, one is a broad general high but locally low and probably is a deep-seated structural high, one seems normal although the control is poor, and one was considered structurally low but is now suspected by some geologists of being structurally high. E. L. DEGOLYER, New York, N. Y.-A large gravity structure, generally referred to, I believe, as the Crosby County Structure, has been found in West Texas. This structure is perfectly symmetrical with the arrows all pointing toward a common center, very much like the Nash salt-dome pattern in Dr. Barton's paper (Fig. 9). One of the peculiar things about it, from the standpoint of the gravity high, is that it is so

Jan 1, 1928

By William Wraith

At the Washoe smelter, Anaconda, Mont., the blister-copper from the converters is transferred, by means of a crane, to a re-fining-furnace, in which it is brought to proper pitch by means of air and poles. From this furnace the refined copper, containing gold and silver, is poured into cast-iron molds placed on a platform-convejor, giving an anode 36.75 in. long, 35 in. wide, and 2 1/16 in. thick. By reason of a disagreement between the smelter and the refinery, in reference to the silver-content of the anodes, it becanle necessary to investigate the methods of sampling used. 11. SMelter Method of SampliNg. At the smelter the sampling is done by " shotting " into water a small portion of the molten stream of copper as it flows from the furnace, by " batting " the stream'with a wooden paddle. The first sample is taken 30 min. after the pouring i.: started, three other samples being taken at 1-hr. interrals, each sample Weighing from 4 to 6 oz. The samples are dried, esamined for particles of burnt wood, screened on a 10-mesh screen of NO. 8 wire to remove the fines, the oversize then screened on a 4-mesh screen of No. 20 wire to remore the coarse, the undersize of this screen being taken as the sample. The four portions thus obtained are thoroughly mixed and split in half by passing over a 16-slot splitting-device, slots being 0.5 in. wide. One-half of the sample is sent to the laboratory for analysis and one-half kept as a duplicate. 111. Refinery Method of Sampling. The method used at the refinery and also used in this in1-estiyation is the one developed by Dr. Edmarcl Keller, of

Jan 1, 1911

By David R. Mitchell, B. M. Bird

DENSE-MEDIA processes utilize the familiar laboratory float-and-sink procedure on a commercial scale. Just as wood chips float on water and sand sinks, so coal floats and refuse sinks when placed in a medium intermediate in specific gravity between the coal and refuse. Liquids intermediate in specific gravity between coal and refuse used in commercial plants are of four types: (1) organic liquids of high specific gravity-halogenated hydrocarbons; (2) dissolved salts in water; (3) pseudo liquids obtained by suspending solids, such as sand or magnetite, in water, and, (4) fluidizing a mass of sand or other solids by air currents. Those most widely used for cleaning coal are solutions of calcium chloride in water and a suspended sand or magnetite pseudo liquid. Laboratory float-and-sink testing is an intermittent operation during which every opportunity is given for particles lighter than the medium to float and particles heavier to sink. Commercial processes are continuous; vertical and horizontal currents of the separating medium occur as either part of the process or unavoidedly produced by the introduction of feed and withdrawal of products, 'so that the exact separation of the laboratory technique is not duplicated by commercial processes. However, separations close to the theoretical are obtained in commercial machines by careful technical control of the process. Most machines in commercial installations are crowded to get as much out of the equipment as possible, so that careful technical control is necessary is get the recoveries and grade of product desired. Sizes usually cleaned are plus ¼ in. or plus 1/8 -in. in the United States and plus 1/16-in. in Great Britain. Coal as small as 1 mm. has been cleaned in some experimental installations. The separation of coal from refuse in sizes finer than about 1/8-in. is made difficult by viscosity effects and hence at the present time cleaning is confined to the coarser sizes. Technical advances in the art of cleaning coal by dense-media processes is progressing rapidly and it is likely that equipment, media, and procedures will be developed to clean sizes down to 0.5 mm. efficiently and at low cost.

Jan 1, 1950

By Roger L. Beals, George A. Tweedy

The results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time; hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data : Pan-Amalgamation. Cyanidation. 1905. 1905. " 1908. Tons treated,.... 51,387 58,983 69,200 Value per ton (U. S. currency),. $ 10.78 $8.39 $8.28 Extraction, per cent.,.. 65.00 88.56 87.45 Extraction, per ton,.. $7.00 $7.43 $7.24 Total cost, per ton treated, . 6.50 4.36 4.01 Profit, per ton treated,.. 0.50 3.07 3.23

Jan 1, 1911

VARYING in thickness and in number from place to place, coal seams in the Canadian Rockies also range in pitch from nearly horizontal to vertical, sometimes with overturns. Over the entire coal-bearing area there are considerable differences of rank in coals of the same geological age, and there are marked differences in ash content and washability characteristics. Correlation of seams at mining operations within a few miles of each other has often proved impossible. These factors influence mining methods, and, of course, production results. The oldest coal formations of western Canada are of Lower Cretaceous age, as the carboniferous sediments are marine and contain no coal. Coal is also present in formations of Upper Cretaceous and Tertiary ages. The rank of coal varies from semianthracite in some operations in the Kootenay and Luscar formations of the Lower Cretaceous in the Rockies to lignite in the Tertiary fields of the Saskatchewan prairies. Fig. 1 shows the general extent of the formations.

Jan 8, 1954

By Robert T. Howard, Morris Cohen

THE purpose of this paper is to direct attention to the lower part of the austenite transformation diagram, or TTT curves, where considerable uncertainty still exists as to the blending of the bainite and martensite reactions. The dissimilarities between these two low temperature trans- formations have been summarized recently by Troiano and Greninger.1 Of particular importance to the present work is the fact that martensite formation, unlike bainite formation, is not suppressed by the fastest quenching rates attainable. However, most of the investigations in this direction have been concerned primarily with the start of the martensite transformation [(M,)] during cooling, rather than with the quantitative aspects of the subsequent reaction on either further cooling or isothermal holding. Several years ago, Cohen2 suggested a form of transformation diagram which reconciled, at least schematically, the isothermal characteristics of the bainite transformation with the insuppressible nature of the martensite transfoi mation. In essence, the diagram consisted of a family of horizontal lines (representing the progress of the austenite-martensite reaction during quenching) which were interrupted in point of time by the bainite family of C-curves extending down from higher temperatures. This picture received later support by metallographic3 and dilatmetric4,5 studies, but the techniques employed were not sufficiently critical to substantiate some of the details. Elmendorf6 and Grange and Steward7 have shown that the Greninger-Troiano metallographic techniques may be used not only for [M,] determinations, but for studying the course of further austenite decomposition. In fact, the latter investigators have observed the amount of martensite formed as a function of temperature below [M,] in fourteen commercial steels. In the present paper, the Greninger- Troiano technique has been combined with the lineal method of Howard and Cohen9 to provide a unique, quantitative treatment of the austenite-martensite reaction. Furthermore, isothermal transformations have been similarly measured on holding at temperatures above and below M,, thus permitting a fairly detailed presentation of the lower part of the conventional austenite transformation diagram. EXPERIMENTAL DETAILS Materials The steels, listed in Table I, were selected for study because they exhibit a satisfactory range of M, temperatures and have not received as much attention as the lower carbon grades. They were prepared as 30 lb induction furnace heats in the laboratories of the Vanadium-Alloys

Jan 1, 1947

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By C. G. Dunn

According to a recently suggested effect of silicon on the re recrystallization textures of high-purity Fe-Si alloys with (111)[112] type rolling textures, the recrystallization texture for a rolled (110)[001] oriented iron crystal probably should be entirely different from that of a (110)[001] oriented 3 pct Si-Fe crystal. Comparative studies of iron and 3 pct Si-Fe crystals, however, show that both have (110)[Ool] recrystallization textures when the rolling textures are the (111)[112] type after reductions in thickness of about 70 pct. Qualitatively the results from the iron crystal are like those of polycrystalline high-purity 3 pct Si-Fe and not like polycrys-talline high-purity iron. The large effect previously noted probably involves unknown impurities or processing variables rather than silicon itself. Some problems on experimental and analytical procedure for a spherical X-ray specimen, which was machined from a laminated composite of sheet specimens, are treated in the Appendix. A possible strong effect of silicon on the textures produced in cold-rolled high-purity Fe-Si (HPFe-Si) alloys during primary recrystallization and normal grain growth was suggested in a recent paper.' All the textures were far from the random-orientation type, but that of iron, or of Fe-Si alloys of low silicon composition, was entirely different from the texture of 3 pct Si-Fe. The same effect was noted for the textures obtained prior to normal grain growth, i.e., for primary recrystallization.2 It is the main purpose of the present paper to provide some clarification of this silicon effect. All the HPFe-Si alloys from zero to 3 pct Si, which were rolled by two or more stages separated by anneals, developed (111)[112] type rolling textures.2 Thus, there was no effect of silicon on the rolling textures. Earlier, Gensamer and Mehl3 also found no effect of silicon on the rolling textures of Fe-Si alloys; they obtained the Kurdjum.ow and Sachs (K-S) rolling texture for iron,4 which is characterized as the three ideal components: (100)[011], (112)[li0], and (111)[112]. There is a difference between the HPFe-Si multiple-stage rolling texture and the K-S single-stage rolling texture, but this is a variable processing effect. Of interest here is the fact that the recrystallization textures from (111) [llZ] type rolling textures were different depending on the amount of silicon in the alloy. There was a relatively strong (110) [001] component in the recrystallization texture of HP 3 pct Si-Fe5,8,2 but no such component in HP 0.6 pct Si-Fe, for example; the recrystallization texture for the latter was two (111) [110] type components and a (111) fiber component 1,2 Several publications have shown that a strong (110) [001] recrystallization texture is derivable from a (111) [112] type rolling texture for 3 pct Si-Fe crystals reduced in thickness by about 70 pct.7-10 Furthermore it appears that the strongest of these (110) [001] recrystallization textures occurred when the orientation of the crystal prior to rolling was (110) [001].7 Barrett and evensoon11 found that the rolling texture of a (110)[001] oriented iron crystal was (111) [llj]. Accordingly, it seemed desirable to determine whether a (110) [001] oriented iron crystal, upon rolling and annealing, would behave like the 3 pct Si-Fe crystal (or the polycrystalline HP 3 pct Si-Fe) and thus produce a (110) [001] recrystallization texture contrary to the suggested silicon effect, or would behave like the polycry stalline HP iron or HP 0.6 pct Si-Fe and thus produce (lll) [110] type components in agreement with a silicon effect. Briefly, the idea here involves the use of more precisely defined textures to obtain if possible better control of important variables that affect the recrystallization process. PROCEDURE A (110) oriented crystal of Ferrovac "E" iron (99.9 pct pure) was prepared in sheet form 0.080 in. thick with the [001] direction parallel to the long dimension of the specimen.'' This crystal was etched to 0.073 in. thickness (to remove some small included grains) and then was cold rolled in a 6-in.-diam mill to a final thickness of 0.022 in. The rolling was unidirectional except for an inadvertent reversal at 0.061 in. thickness. At this thickness, and also at 0.040 in., the rolling was interrupted for transmission Laue photographs. Molybdenum Ka-radiation filtered with zirconium was used in a transmission method1' to obtain the cold-rolled (110) pole figure. The sample was a 0.002-in.-thick section taken from the central region of the 0.022-in.-thick cold-rolled crystal. For the primary recrystallization study, cold-rolled samples were etched from 0.022 to 0.021 in. thick and annealed in hydrogen at 850°C. Primary recrystallization to a fine-grained structure, Fig. 1, was obtained in a 5-min anneal. Eleven sheets after

Jan 1, 1963

By J. A. Woolf, E. S. Leaver

The presence of soluble base metals in precious-metal ores usually precludes cyanidation as the best method of treatment. The laboratory experiments described in this paper show the possibility of cyanidation of gold-silver ores containing less than 0.5 per cent. of cyanide-soluble copper and the effect of zinc in the cyanide solution. Part I.—Copper in Cyanidation The proposed process of cyanidation of precious-metal ores containing copper is based on the regeneration of about 80 per cent. of the cyanide used in the dissolution of the copper. The method of regeneration involves a combination of the sulfide and the acid precipitation of the copper and silver. The resultant solution is made alkaline with lime, and the gold is precipitated with zinc dust. Solubility of Copper Minerals in Cyanide Solution In order to determine the solubility of copper minerals, including metallic copper, under the usual conditions for cyanidation, experiments were conducted with synthetic ores. Each ore sample was prepared by mixing the particular pure copper mineral with barren sea sand. Both the mineral and sand were ground to pass 100 mesh before they were thoroughly mixed. The percentage of copper in each head sample was determined by direct assay, excepting the metallic copper sample, which was computed on weights before mixing. Table 1 gives the results. Azurite, bornite, chalcocite, cuprite, malachite and finely divided metallic copper are readily and completely soluble under the usual conditions for cyanidation. Enargite and tetrahedrite are sufficiently soluble to cause an excessive loss of cyanide, and they also cause fouling of solutions with arsenic and antimony. Precious-metal ores containing small percentages of chalcopyrite or chrysocolla may give satisfactory returns with the usual cyanidation.

Jan 1, 1930

By G. L. Oldright

THE upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the opera-tion of sintering. A sinter feed with normal gangue constituents, con-taining more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead con-centrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1940

By John M. Cummings, Warren. Harry V.

THE Geology Department of the University of British Columbia has undertaken the task of examining the ores from as many as possible of the gold mines of British Columbia. The object of this work is two- fold. First, it is known that detailed mineralographic studies are useful in attacking ore-dressing problems, and these studies are intended to be helpful to mill operators. Second, it is hoped that mineralogical and mineralographical studies will prove useful adjuncts to those of lithology and structure in throwing more light on problems related to the origin of the deposits. The paper shows that gold, for all practical purposes, is not present in an ore mineral in solid solution nor as a eutectic with any mineral; if the latter were true the gold particles would be distributed equally throughout that mineral. The gold occurs either as native gold or as a gold-silver telluride and is not distributed regularly through any mineral or minerals. The relationship between the gold or gold-bearing telluride and the associated minerals affords a means of classification that is not only simple but also appears to be directly related to the geological nature of the deposit, which may be summarized as follows: 1. Disseminated Gold Type.-Precious minerals in extremely small grains, which are distributed without regard to grain size, fractures or grain boundaries: (1) Hedley variety-gold in native form; (2) Surf Point variety-gold predominantly as telluride. 2. Veining Gold Type.-Precious minerals in grains of various sizes, which occur mainly along fractures and grain boundaries: (1) Cariboo gold quartz-goldin native form. (2) Waneta variety-gold as telluride. Application Te Ore Dressing These mineralographic studies have proved to be of value to mill operators, and future studies of a similar nature should prove increasingly useful because every year provides a further opportunity to correlate

Jan 1, 1937

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By Albert J. Phillips

As early as 1824, Haidinger' described crystals of native copper that were, according to Dana,2 " probably twinned parallel to the octahedral plane and normal to this axis." In 1837, Rose3 very clearly demonstrated that native copper crystals were commonly twinned on the octahedral plane. Lasaulx,4 in 1882, described polysynthetic octahedral twins and stated that enclosed twinning lamellae were observed. Even on crystals formed artificially by electrolysis, twinning was observed as early as 1886, by Brown.5 Many other descriptions of twinning in native copper and in gold and silver are to be found in the literature, and in every case with which we are acquainted the twinning is conformable to the spinel law; i. e., the octahedral plane is both twinning and composition plane. Metallurgists have long been familiar with the straight-sided bars or bands that commonly occur within the irregularly outlined grains of metallic crystalline aggregates. They are certainly found in nearly all metals of the face-centered cubic type after cold working and annealing. If a specimen showing these bands is rotated, keeping the angle of incidence of the illuminating beam constant, they usually exchange color contrast periodically with their respective matrix crystals. Also slip lines, when produced in these specimens, nearly always show a change in direction upon passing through the bands, giving rise to the "stairway" effect often illustrated in metallurgical textbooks. Apparently the only quantitative observations on bands of this sort were made by Osmond and Cartaud6 on austenitic steel. They selected,