Search Documents

By AIME AIME

BY COMBINING the sessions on reduction and refining of copper, lead and zinc it was possible to devote an entire day to nonferrous metallurgy. Four interesting papers were presented at the morning session and four more in the afternoon. In the discussion of papers on copper, F. R. Pyne acted as chairman, with H. M. Shepard as vice-chairman, whereas for those on lead and zinc, F. F. Colcord acted as chairman, with C. R. Hayward as vice-chairman. The paper by P. D. I. Honeyman on the smelting of raw concentrates in the reverberatory furnace was presented by Mr. Pyne and discussed by Messrs. Mazany and Hayward. The interesting paper by E. S. Bardwell, com- paring the use of various fuels in copper-refining furnaces at Great Fails, Mont., was presented by Mr. Shepard and discussed by Messrs. Boggs, Gronningsater and Hayward. That by R. G. Knickerhocker, describing the stationary basic copper converter at Messina, Transvaal, was presented by Mr. Pyne, together with a written discussion by c. R. Kuzell, of the United Verde Copper co. It was an interesting illustration of how well-known processes may sometimes be modified to fit into unusual conditions.

Jan 1, 1932

The primary purpose of the Institute is to advance those sciences embraced by it through interchange of knowledge This can best be done by the presentation and discussion of technical papers by its mem¬bers Short practical papers are especially welcome In any case the author should satisfy himself that his material is of a quality that will be a credit to him and to the Institute The preparation of a good paper frequently leads to a reorientation of the author's thoughts, which is extremely valuable, and pertinent dis¬cussion thereof contributes in no small way to the professional standing of the author Members are urged to submit papers presenting the results of their work Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts 1 Subjects: The subject must be within the field of the Institute Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasion¬ally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper The mere fact that the work is original does not necessarily justify publication it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record It is rarely desirable to subdivide the results of a single research for publication in a variety of journals Pre¬vious publication is a bar to acceptance 2 Construction : Papers should be clearly and concisely written in good English Care in this regard insures wider reading and the saving in space permits the Institute to publish more papers The terminology and units employed should be those current in the particular field An examination of Institute publications will afford useful guidance in such

Jan 1, 1937

For the year ending February, 1919 PRESIDENT SIDNEY J. JENNINGS NEW YORK, N. Y. PAST PRESIDENTS L. D. RICKETTS NEW YORK, N. Y. PHILIP N. MOORE ST. Louis, Mo. FIRST VICE-PRESIDENT C. W. GOODALE BUTTE, MONT. TREASURER GEORGE D. BARRON NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 1, 1919

By Charles Pack

DIE castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into threee groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. CASTING MACHINES The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly. apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings.

Jan 2, 1919

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry-a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal involves environmental protection and the economics of refuse handling. For over two years, Monterey Coal Co. has operated a non-polluting refuse disposal system at its No. 1 Mine located in Brushy Mound Township of Macoupin County 6 miles south of Carlinville, Illinois. Drainage goes to Spanish Needle Creek and eventually to the Illinois River. The mine produced 3.5 million tons of clean coal during its first two and one-half years of operation and is designed to produce 3 million tpy of clean coal at capacity.

Jan 6, 1973

By Spencer S. Shannon

This chapter is concerned with the uses, geology, exploration, evaluation, preparation for markets, and future of 90thorium and 39yttrium, along with 14 rare-earth elements. The rare-earth metals or lanthanides were divided into three categories by Berzelius. The cerium subgroup is comprised of 57lanthanum, 58cerium, 59praseodymium, 60neodymium, and 62samarium. 61Promethium does not occur naturally. The terbium subgroup includes 63europium, 64gadolinium, and 65terbium. The remaining lanthanides are placed in the yttrium subgroup. Strictly speaking, yttrium is not a rare earth. Because the properties of yttrium resemble those of heavy rare earths, its name has been used as a designating adjective. The yttrium subgroup includes 66dysprosium, 67holmium, 68erbium, 69thulium, 70ytterbium, and 67lutetium. Rare-earth elements, especially those of the same subgroup, tend to occur together rather than in discrete minerals.

Jan 1, 1975

By Rebecca Mae Summer

Increasing urbanization and industrial activity require increased supplies of sand and gravel. This means expanded surface mining and despoiled land near population centers. Highly competitive land use demands justify serious consideration of premining planning for multiple land use and reclamation concurrent with mining. 1-5 Formulating solutions to environmentally and economically sound uses requires a comprehensive approach based on properties of the natural resource base--geology, soils, and water. A study of sand and gravel mining within Pleistocene-Holocene fluvial deposits in Colorado County. Texas [(Fig. 1)] illustrates how physical limitations imposed by the resource base are determined.6,7 Data from drillers, logs of water wells, test boreholes, field observations, and laboratory analyses are used to evaluate these physical controls. Knowledge of the thickness and composition of overburden aids in developing optimum reclamation and revegetation plans. Most of the overburden in the study area [(Fig. 2, 3)] is a clayey mud with variable amounts of silt and fine sand. A comparative textural analysis of overburden and native soil is used to assess changes incurred by mining and for evaluating other physical characteristics, e.g., ability to support crops, permeability. and shrink-swell potential. Textures are correlated with soil types found in the area [(Table 1)] to get an approximation of probable surface properties expected from these mined materials. Results of textural analyses [(Table 2)] indicate that separating topsoils from overburden during mining is not necessary because the range of overburden textures is about that of native soils. However, more data is needed on nutrient deficiencies to evaluate fertilizer requirements for successful revegetation.*6

Jan 1, 1979

By Raymond B. Ladoo

Wollastonite is a calcium metasilicate, with the formula CaSiO3; containing theoretically 48.3 pct CaO and 51.7 pct Si02. It is one of many natural and synthetic silicates with varying CaO/SiO2 ratios, with and without water of crystallization. While it is a very common mineral, deposits of sufficient size and purity to be of commercial interest are unusual. There is only one producer (1958) of wollastonite for industrial use in the United States, Godfrey L. Cabot, Inc. at Willsboro, New York. There has been a small production of surface material for ornamental use from near Blythe, California. Carload tests have been made on California wollastonite for making mineral wool and a commercial plant for this purpose was projected in 1957. Properties Wollastonite is monoclinic and commonly occurs in masses or aggregates of bladed or needle-like crystals. It has a perfect cleavage parallel to the long prismatic axis. It is rather brittle and some types grind easily to a very finely fibrous product, but other types, due to interlacing of fibers, are tough and difficult to grind. Mobs hardness is 4.5 to 5; specific gravity 2.8-2.9; index of refraction 1.616 to 1.631; melting point 1,512°C. Color when pure is a brilliant white, but when less pure it may be gray or brown. Luster is vitreous, transparent to translucent. Common mineral associates are garnet (several varieties), diopside, calcite and quartz. The nature of the mineral impurities determines to a large degree the commercial value of a deposit. At Willsboro, New York, the impurities consist chiefly of iron garnet and iron diopside which are both magnetic and so are easily removable by magnetic separation, yielding a nearly theoretically pure product. Some deposits in California contain calcite and quartz which cannot be removed cheaply, thus limiting market possibilities. Occurrence Wollastonite is a contact metamorphic mineral occurring in most places within or associated with impure limestones. The deposits at Willsboro, New York1,2,3,5 consist of two or more beds dipping 15-50°E and striking NW-SE. The main bed, 30 to 70 ft thick, may be traced on the surface for at least 2 ½ miles. In this belt, the Pre-Cambrian Grenville limestone has been injected and partially replaced by the more liquid portions of an anorthositic magma. Buddington and Whitcomb3 have described the rock as "Mixed gneisses, pyroxenite and garnetiferous gneisses and skarns." Prospecting revealed the wollastonite at ten different places in the belt, overlain in most places by a garnet rock. Diamond drilling has proven several million tons with probable reserves around 15 million tons. Interbedded with the wollastonite are beds of garnet from a few inches to several feet in thickness. In the wollastonite ore itself the chief and almost only associated minerals are garnet (mostly almandite but some andradite and grossularite) with small amounts of green hedenbergite. Inasmuch as the almandite and diopside are magnetic they are easily separated from the wollastonite in high intensity magnetic separators. If grossularite should occur in quantity other means of separation would be needed. Wollastonite has been reported at 35 localities in California12 but only those in the Big Maria and Little Maria Mountains, 16 to 20 miles north of Blythe, Riverside County, are

Jan 1, 1960

THE following employment items are made available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Project Manager or Construction Engineer, 48, married. Twenty-five years' experience on mine, mill and smelter construction work, design and operation, U. S. and Mexico. Speak Spanish. Now employed; available 30 days notice. Prefer U. S. or Mexico. M-698-489-E-1-San Francisco. Mining Geologist, 53, single. Eleven years' intensive field experience giving a completely practical competence for the smallest or largest of areas; plus the highest possible grade of academic background and independent research qualifying for top rating. Available in thirty days or less. Any location acceptable. M-699-3611-E-7-San Francisco.

Jan 1, 1952

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By Nicholas J. Grant, William H. Ferguson, Bill C. Giessen

Ta-lr alloys have been examined over the complete range of compositions using metallographic and X-ray techniques. The terminal solid-solubility limits, solidus temperatures, and intermediate phases were determined. There are four inter-mediate phases: o, tetragonal, analogous to a (Fe-Cr); 0,. orthorhombic; az, tetragonal; and a TaZr,, cubic, AuCu, structure. Of these, o and a, melt peritecticaLly, a, decomposes peritectoidally, and a TaIrs has a congruent melting point. Three peri-tectic and one eutectic reactions occur. 1 HE Ta-Ir phase diagram has not been treated in the literature. Intermetallic phases and terminal solid solubilities have been described and estimated.'-4 The previous findings have been confirmed in this work. A complete diagram with additional phases and solidus curves is presented. EXPERIMENTAL METHODS Starting materials were tantalum powder of 99.8 pct purity, supplied by the National Research Corp., Cambridge, Mass., and iridium powder of 99.9 pct purity, supplied by the Bishop Co., Malvern, Pa. Both powders were -200 mesh. Table I lists the analyses as given by the suppliers. A standard procedure was employed in making the alloy buttons, which was described in detail in Refs. 5 and 6, and which included repeated arc-melting of powder compacts and determination of the composition by the weight-balance method. This is especially justifiable due to the similar vapor pressures of tantalum and iridium. In the critical parts of the diagram, a spacing of 1/2 at. pct was used, based on premelted master alloy material. The observed structures and X-ray spectra were consistent with the composition sequence of the alloys. Table II lists the final alloy atomic percentages with the calculated percent error of composition. Cross sections representative in grain size and composition were selected for the study, as described in Ref. 5. Based on prior experience, no contamination from the tungsten electrode was considered. Temperature measurements were obtained using a Leeds and Northrup optical pyrometer and have been described extensively in Refs. 5 and 6. All heat treatments were made in the high-vacuum tantalum tube furnace mentioned in Ref. 5. Samples annealed in tantalum containers cooled from 1800" to 1000"~ in 5 sec; those annealed in ceramic crucibles cooled over the same range in 15 to 30 sec. The thermal treatments are listed in Table 111. All specimens were homogenized at 1735°C for 24 hr. Tantalum-rich compositions were treated in tantalum buckets. Iridium-rich compositions were annealed in tantalum buckets below the eutectic temperature of 1950°C; up to 2200°C, tungsten-lined tantalum baskets were used; and above 2200°C thoria crucibles were used. It was found that refractory oxides (in early stages of the investigation alumina crucibles were used up to 1800°C and thoria crucibles were used to 2400"~) give off minute amounts of oxygen and thereby influence the microstructure considerably, or react directly with the alloys.

Jan 1, 1963

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.' The specific conductances ranged from about 100 ohm-' cm-' for pure Cu2S to 1500 ohm-' cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-' cm-'. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne' detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-' cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-' cm-'.' Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.' A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By Clark B. Risler, Walter E. Thomas

MILL planning must include electrical drives and a system to supply them. These should be considered at the time metallurgical and mechanical plans are being made. Because it is convenient, flexible, reliable, and economical, electricity is the accepted source for powering mill concentrating equipment. Ore-treating mills have grown to the point where a single mill has been built using 360 motors ranging from 1 to 1000 hp and totaling 50,000 hp. Such a system of electrical drives can be scattered over a square mile and employ 4000 to 220 v. Drive Motor Characteristics: Since ore processing is predominantly a continuous operation, very few of its drives require wide speed variation after initial adjustment. Consequently squirrel cage, wound rotor, and synchronous alternating current motors are most often used.

Jan 5, 1957

By Joseph B. Darby, Paul A. Beck

IN isothermal sections of several ternary systems, the a-phase was found1 to extend in the form of a relatively narrow elongated field, connecting the U-phases that are present in the adjoining binary systems. This was interpreted in accordance with the conception that the U-phase is an electron compound and the ternary U-phase fields were shown in several systems' to extend approximately in the direction of constant average d-shell electron vacancy number per atom. ' However, in the various isothermal sections of the Fe-Cr-Mo system" the ternary a-phase field was

Jan 1, 1958

By S. J. Green, R. D. Perkins

Little data exists on the high strain rate behavior of geologic materials. Uniaxial stress tests by Kumar1 and by Serdengecti and Boozer2 present some results to strain rates in the range 10 to 103 per sec. The two references cited are the only ones the authors found for high strain rates. Techniques for experiments at high strain rates are not well developed and, in general, leave questions with respect to interpretation of data when the material behaves in a brittle manner. The most reliable data at very high strain rates (104 to 106 per sec) are found in some recent flat-plate work3-5 where experimenters have impacted one plate into another, thereby creating a uniaxial strain loading. The standard uniaxial stress-strain curves cannot be obtained directly from these tests; however, yield (or fracture) may be studied by measuring the "elastic" wave magnitude. These data then may be compared to uniaxial stress data by resorting to some preassumed yield/fracture criteria. Even with the most liberal interpretation of existing data, little can be said of the effects of high strain rate on stiffness, yield/fracture, and post-fracture behavior of geologic materials. It is the purpose of this work to begin to add to the understanding. The data presented here are intended to provide material information for use in calculating the response of geologic materials to high rate deformations. These data can be applied directly to determine parameters such as the elastic modulus and Poisson ratio as a function of stress. Furthermore, these data can be used to derive an understanding of yield/fracture and the effect of rate on the yield/fracture surface. The work presented is a first step, and is

Jan 1, 1972

By H. A. Wheeler

That lead and zinc deposits are the result of prolonged,, slow deposition is the idea of most students of ore deposits, and in many cases, where the ore-bearing solutions have been very weak or the precipitating conditions have been very feeble, the ore accumulations have undoubtedly taken a long period of time. As these two vital conditions have been subject to great variations in the different mining camps, the following example is highly interesting in showing that deposition can be very rapid under favorable conditions, geologically speaking, and also extremely recent. In fact, the writer is inclined to regard most, if not all, of the Mississippi Valley deposits of lead and zinc as probably being very young, at least not older than Tertiary, if not Quarternary, in age. The extensive Joplin lead and zinc district, in southwestern Missouri, which is about 60 years old and has numerous mines that were abandoned from 1 to 50 years ago, shows that the lead and zinc today are in an active condition of solution and redeposition, although these two metals occur in the predominant form of sulfides. The mine waters from the older and more or less abandoned portions of the district are frequently so acid, mainly from the oxidation of associated pyrite, as to necessitate the use of wooden pipes and pumps. The first boom in the Oklahoma zinc fields, which is the southwestern extension of the Joplin district, occurred when ore was accidentally struck in drilling a water well. Among the mines then opened up was the Mission mine, at Lincolnville, Ottawa County, Okla. This mine was opened in 1903 in lean "sheet ground," or a flat blanket formation of chert carrying disseminated zinc blende, or "jack," and galena. Theore-body was very free from iron pyrites and the concentrates were very high grade, the "mineral," or lead concentrates, assayed 80 to 85 per cent. lead and the jack, or sphalerite, assayed 60 to 65 per cent. zinc. The orebody was very shallow, occurring at a depth of 76 to 95 ft. (22 to 28 m.) and very wet, requiring three or four pumps to handle the water. The mine was operated until 1914, when it was closed by litigation and immediately filled with water. The second Oklahoma boom, five years ago, opened up the large, active camps of Picher, Tar River, and Century, which are located 2 to 5 mi. west of Lincolnville. They are considerably deeper, being farther down on the westwardly dipping monocline that emanates from the Ozark

Jan 1, 1920

By H. K. Work, G. H. Enzian

In the manufacture of steel for commercial purposes, the deoxidation practice used, i.e., the method and degree of deoxidation, is an important factor affecting the structure and mechanical properties of the finished steel. Deoxidation practice exerts a pronounced influence not only on the soundness of the ingots but also on the reaction of the steel to a number of mechanical and thermal treatments. The first mentioned effect of deoxidation is more or less obvious and was first demonstrated, though perhaps not fully appreciated, by Robert Mushet when, in 1856, he added speigeleisen to low-carbon bessemer blown metal. In 1861. Bessemer patented the addition of one pound per ton of silicon to his blown metal to "cause the metal to lie quietly in the mold." The second effect of deoxidation-—that is, the effect on the properties and behavior of the steel—is, one might say, more subtle, and certainly not as well understood as the first, although in many cases it is the more important consideration. This paper is limited to a discussion of only the second effect of deoxidation and: in particular, to the effect on the strain-sensitivity of low-carbon steels. General Discussion Originally it was thought that the function of a deoxidizer was to combine with the oxygen present in the steel as iron oxide and prevent its subsequent evolution as a gas. -More recently it has been realized that a deoxidizer does more than this. Frequent reference has been made to the effect of deoxidizers on the nitrogen in the steel, and some attention has also been paid to hydrogen. As a consequence of the above situation any study of deoxidation must be concerned with the gas content of the steel and the effect of the deoxidizer on the gases involved. The term "gas content" as used here refers to gases extracted from steel during melting in vacuum rather than to elements present in steel in the gaseous state. The extracted gases, at least in the case of oxygen and nitrogen, are generally accepted to be products of decomposition of oxides, nitrides, or other more complex compounds. The manner in which deoxidation affects the gas content of steel and the significance of gases in steel have been and still are subjects of considerable speculation. No attempt will be made here to give a complete discussion of the literature on this subject but a few references will be cited for purposes of illustration. N. Hamilton1 found a correlation between the oxygen content of alloy steel and the behavior of the steel during tube piercing. Davenport, Bain, and others associated oxygen with aging properties of steel while Köster5 and a number of others6-lo made similar claims for nitrogen. Daniloff, Mehl, and Hertyll stated that "deoxidation decreases the susceptibility of steels to aging directly

Jan 1, 1945

By A. Tanaka, K. G. Carroll

The existence of local room-temperature plastic flow in germanium, which has been a subject of controversy for nearly two decades, has recently received renewed attention, albeit no more agreement than hitherto. Phenomenologically one major facet of the problem has been reduced to the question whether or not indentation can be effected in germanium without the introduction of cracks. That plastic flow can be induced at room temperature by fracture appears to have been rather convincingly demonstrated recently by Suzuki and Kamada and by Noble and Henisch.1 The literature contains both direct and incidental references to Vickers and Knoop indentations showing no cracks, within resolution of optical microscopy. Recently, however, following a controversy on the subject,2,3 johnson4 made a study of indentations produced by spherical indenters and concluded that these are accompanied by cracking. This study in-

Jan 1, 1969

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2 by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn = MnO + Fe [A]slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aMoO aFeI1 dFec) aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term [afe] may be combined with K" to give a new constant K'. Making these changes,

Jan 1, 1942