Search Documents

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By Y. Takahashi, I. Iwasaki, S. Tanabe

Supported by the vigorous capital investment of the heavy and chemical industries and by the ever-increasing demand for durable consumer goods in the past decade, Japan has now emerged as the world's third largest steel producer, surpassed only by the United States and the Soviet Union. In 1968, the crude steel production is expected to exceed 50 million tons; the per capita steel consumption at that time will reach 886 lb, approaching the level of Western Europe. Characteristics of the Japanese steel industry is the high dependence of raw materials on overseas sources. Before World War II the industry relied on North China and Manchuria for coking coal, and on middle China, Hainan Island, the Philippines and the Malayan Peninsula for iron ores. After the war, the major sources of iron ores were shifted to the Philippines and the Malayan Peninsula, supplemented by shipments from the United States, Canada, India and Goa. The United States, in addition, became the primary source of coking coal.

Jan 1, 1967

By L. E. Mannion

Sodium carbonate (soda ash) is one of two principal commercial alkalis. Its principal competitor is sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines and solid salts provided impure soda for early glassmaking. Until the 19th century, soda ash (as well as potash) was recovered mainly by leaching wood or other plant ashes. In 18th-century Europe, for example, leaching seaweed ash with hot water produced a brown laundry lye. One of the better grades of this material was a Spanish product, barilla, which analyzed 24 to 30% Na2CO3 (Hou, 1942). The modern chemical industry was born in 1691 with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. English industry used this process extensively in the 17th and 18th centuries. The next major advance was in 1863, when Ernst Solvay devised the ammonia-soda, or Solvay process. The first of many Solvay plants was built in 1874. These supplanted the LeBlanc method and dominated worldwide soda ash production until 1974, when mined sodium carbonate became predominant. Although considerably less important until recently, natural sodium carbonate deposits historically have supported small soda ash operations throughout the world. Shortages during World War II stimulated production of "natural" soda ash from such deposits, particularly at Searles Lake, CA and Lake Magadi, Kenya. More spectacularly, increased production from the vast trona deposits in Wyoming has virtually supplanted the Solvay process in the US. Principal producers of natural soda ash as well as the character of the source deposits are listed in Table 1. [ ]

Jan 1, 1983

By H. W. Weart, D. J. Mack

SINCE the first recognition of eutectic solidification as the simultaneous formation of 2 solids from one liquid,1 many complex structures thus produced have been observed. Despite many attempts to ascertain it, however, the detailed mechanism by which these structures develop remains obscure. In an attempt to clarify the origin of eutectic structures, the study described in this paper was undertaken. The broad objective of the study was to investigate the effect of different solidification conditions on the structure of single eutectic grains. It was expected that the eutectic structure would thereby be isolated for study, but preliminary experiments revealed another structure within each grain. When a literature surveye revealed only 1 previous mention of the subgrain structure,' it was decided to determine the origin of the structure and to study its response to various growth conditions. Before presenting the details of the investigation, it is apropos to distinguish carefully among the 3 structures produced during eutectic solidification. This is especially desirable in view of the apparent confusion existing in the literature concerning the structures in a eutectic specimen. The confusion is due largely to the existence of the subgrain structure noted above which is easily mistaken for the grain structure. In the following paragraphs, an effort is made to distinguish the 3 structures by briefly describing their origin during solidification, even though the results are thereby anticipated slightly. The 3 structures produced during eutectic solidification are the grain structure, the colony structure, and the eutectic structure, each one contained by the one preceding it. The grain structure is analogous to the polycrystalline structure of a metal or inle-phase alloy in that each grain grows from a single nucleus. A somewhat broader interpretation is needed here, however, because of the presence of 2 phases in each grain. Since in most eutec-tics particles of 1 phase are dispersed in a matrix of the other, a grain may be taken to be the region in which the matrix phase is monocrystalline.*

Jan 1, 1959

J. M. Wadsworth,' Okmulgee, Okla. (written discussion).—It seems to me that thc young man must first be absolutely sure that the work he has taken up is to his liking and then I would advise that he get into the practical end of it and learn as much about it as he can as fast as he can. For instance, in the refinery business the college man, graduated in chemical engineering, should ground himself by going through the various departments in a refinery and working in them until he is thoroughly familiar with the operating problems. In a short time he would be able to apply many things which appear in the abstract form in his college work and this would opcn up an opportunity for him to capitalize on them, promoting his own interest. I do not criticize the present-day college men as a class, but I have found that many of them come into your plant with the idea that mere possession of a diploma should insure rapid promotion; in a short time they are impatient and usually leave. We have found in employing men that the single attribute most difficult to find in them is a lot of energy and whole-hearted interest in the work at hand, and it seems to me that if a man combines these with a careful technical training he should be fairly well equipped to gamble on his future. They must learn that the biggest satisfaction to be gained in life is in their work. Procedure for Attaining Objective of Young Petroleum Engineer H. B. Fell,+ Ardmore, Okla. (written discussion).—Of course, the first thing to be ronsidered in any proposition is the ultimate objective that is desired to be attained. 1 presume that the desired objective of most of the young men graduating in petroleum engineering will be that of chief executive of one of the companies in the petroleum industry, or one of the allied industries, or to become an independent oil producer, or oil refiner, or possibly an oil distributor. The next phase then to be considered is the procedure which should most logically be followed to attain the objeckive of the indivitlual, since in these cases these young men will have been trained in a course in petroleum engineering and it would logically be presumed that the attainment of their objective should be through the operating end of the branch of the business with which they are connected. The operating end is, of course, the department of each branch of the business that develops the resources, or refines the products, or distributes the products, from which the profits are derived, and is a part of any business which is filled with enough interesting work to appease the desires of the most ambitious young men. In order to get the best possible training it would appear to me that the place for a young man to start after graduation would be at the bottom of that branch of the industry which he expects to follow. For example, if he is going in the producing end he can gct no better training than is secured by starting as a roustabout in the ficltl, where he romes in constant rontact with the character of work that is necessary

Jan 1, 1928

By R. E. H. Pomeroy

The statistical data given in this paper are taken from the actual performance of the No. 2 reverberatory furnace of the Nevada Consolidated Copper Co., Mc Gill, Nev., for a period of four months, from April to July, 1914. The principal furnace dimensions are: Length, 132 ft. % in. at the skim-line level; average width, 18 ft., 10 in. at the skim-line level. The roof is 7 ft. above the skim-line level at the firing end. The average area in the uptake flue is 36 sq. ft., and the area above the skim line under the vulcatory arch is 24.3 sq. ft. Fig. 1 shows a diagrammatic plan and sectional elevation of this furnace. The furnace is equipped with two 400-b.h.p. Stirling waste-heat boilers set in parallel. California crude petroleum is used for fuel and has a specific gravity of 16.5" B., flashing in open test at 199" F. The oil is heated to about 200" F. in a steam heater before going to the burners, requiring about 9 b.h.p. per furnace day to heat it from the line temperature to the burning temperature. Measurement is made by oil meter, checked daily by reservoir readings. The oil is fed by gravity (34 Ib. static pressure) to seven low-pressure blast burners of the Steptoe type (Fig. 2). The blast for these burners is supplied at about 40-08. pressure by a motor-driven Connersville blower of 42 cu. ft. capacity per revolution. The air supplied by the blower through the burners for atomizing the oil amounts to about 10 per cent. of the theoretical air necessary for complete combustion of the oil. The remainder of the necessary air enters the furnace through the burner openings in the firing wall. No checker holes are provided, and the charge holes in the roof are equipped with slide gates and " dog houses" to minimize air leakages. The combustion of the fuel, as shown by gas analysis at the front of the furnace, is practically complete, the carbon monoxide in the gases being less than 0.5 per cent. The draft at the firing end of the furnace is 0.18 in. of water. At the throat or in the uptake above the "verb" the draft is about 1 in.

Jan 1, 1915

AT the meeting of the Board of Directors held on June 25, 1926, and in response to numerous in-dividual suggestions for changes, a committee on Re-vision of the Constitution and By-Laws of the Insti-tute was appointed, consisting of C. F. Rand, Archi-bald Douglas and H. Foster Bain. Various confer-ences were held, much correspondence conducted and a preliminary draft was prepared. It proved imprac-ticable to complete the work in time to submit the matter to the membership for approval or disapproval at the annual meeting in 1927, and the Committee was continued with instructions to prepare a report as a basis of action in 1928. After Mr. Rand's death George Otis Smith was appointed in his place and the tentative draft herewith submitted has been pre-pared in its present form by Messrs. Smith, Douglas and Bain, though not differing in any material mat-ter from an earlier draft approved by Mr. Rand. In preparing this the Committee has kept in mind primarily the desirability of simplification and of making the By-Laws conform to the actual practice of the Institute as worked out through experience. The Constitution and By-Laws adopted in 1912, and which with minor amendments only still govern the Insti-tute, are full of specific provisions regarding pro-cedure; such as that laid down for guidance of the Papers and Publications Committee. Many of these have proved unworkable and in practice have not been always strictly followed. It now seems wise to write into the Constitution and By-Laws only the general fun-damental principles to he followed and to provide for such easy change in methods of following them out as will permit efficient conduct of the business. It is this thought that has guided the Committee in rewrit-ing many of the sections. With this in view also the Constitution, as such, has been shortened to the brief-est feasible statement of fundamentals. All matters relating to means of making these principles effec-tive have been put into the By-Laws or in the hands of committees whose work is subject to control and whose rules are subject to approval or disapproval by the Board of Directors. Many suggestions for changes have come to the Committee that have not been incorporated in this draft. Some of these are in themselves excellent but have not been incorporated here because the Commit-tee discovered no sentiment for them such as would be likely to secure their approval, or found them out of harmony with the general plan followed herein.

Jan 9, 1927

By Jesse O. Betterton, Y. E. Lebedeff

AS a matter of the most widespread interest to lead-refining metallurgists, the process of desilverizing lead originated by Parkes is the most fundamental step in lead refining. While this basic operation, in addition to effecting a practically complete recovery of gold and silver, is also a great purifying operation and a governor on the purity and uniformity of the final refined lead, it has the important deficiency that no bismuth is removed in the operation. The problem of finding a satisfactory, inexpensive method for removal of bismuth that would fit in with the basic desilverization step has been one of enticing interest for lead-refinery metallurgists for many years. Of late it has become one of imperative interest, and while many attempts and much progress have been made, it is probably fair to say that metallurgical progress thus far is only catching up with commercial requirements. The Pattinson process, an original competitor of the Parkes process for desilverization, has received much attention for its possibilities for bismuth removal. Bismuth concentrations in the Pattinson process fall far short of the silver concentrations and as a result too many operations are required and a crawl in grade in the kettle units is experienced which requires periodic correction. Altogether, it has proved too expensive a remedy, from the cost standpoint of both installation and operation. The Betts electrolytic process is a fully satisfactory remedy but its present status in the field of lead refining is more a matter of bismuth removal than preference as a refining system, except, of course, in instances particularly favorable to the basic requirements of the process. The Betts process, of course, is essentially different from the Parkes process, and very difficult to associate therewith to any economy except in minor ways. Accordingly, where economy dictates the Parkes process, and this is true of far the greater portion of the world's tonnage, the adoption of the Betts process primarily for bismuth removal is apt to prove an expensive remedy on account of its normally higher cost of operation, inelasticity of the equipment for variable tonnages, and high per ton cost of installation.

Jan 1, 1937

By H. J. Wasson, E. B. Hopkins

Throughout 1928, production of oil from Venezuela steadily increased, and at the close of the year, the output was at the rate of nearly 400,000 bbl. a day. The total for the year was approximately 106,500,000 bbl., representing an increase of about 66 per cent. over the 63,000,000 bbl. produced in 1927. Venezuela now stands next to the United States as the second largest oil-producing country in the world; and there is abundant evidence to suggest that this relationship will endure for a number of years. Reserves were notably increased in the Lake shore fields, and the potential output of the Maracaibo Basin is much greater than the current production. In spite of this, the percentage of production increase was comparatively moderate, and the rate of this increase continued to fall off slightly, as has been the case for the last three years. This does not suggest that further annual increases in Venezuelan output will not materialize; only that the rate of these increases appears to be on the decline, and that with every succeeding year the future tendency will be in the direction of a stabilized level of output. The following table shows the production trend of the country since 1925: 1925 increase over 1924, 132 per cent. 1926 increase over 1925, 80 per cent. 1927 increase over 1926, 75 per cent. 1928 increase over 1927, 66 per cent. Many factors will work to prevent a reversal of this trend, but the principal ones are strong ownership in large-acreage units, and the probable indisposition of the world market to absorb a more rapidly increasing Venezuelan output at prices profitable to the producers. The distress oil element is not a factor in Venezuela; also, any unforeseen jump, such as results in the United States from the discovery of a Seminole or a deep sand at Long Beach, or Santa Fe Springs, is impossible in Venezuela, on account of lack of means for transporting a sudden surplus of oil, and the slowness with which additional transportation equipment in the form of shallow-draft tankers can be obtained.

Jan 1, 1929

By A. N. Winchell

Petrographic studies of over 1400 rock and mineral samples, and studies of their field relations, show that there is a complete gradation between sandstone and limestone; the lime-silicate rocks were produced by recrystallization of limestone; mineralization and silicification occurred after silication and at considerably lower temperature; carbonation occurred at still lower temperatures. IN CONNECTION with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Bingham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance.

Jan 3, 1924

By Thomas E. Ban, Charles D. Thompson, Charles A. Czako

Continuous sintering-a metallurgical process for more than 50 years-has broadened from its origin in nonferrous metallurgy to present-day applications in ferrous, chemical, and nonmetallic fields. During the past year, self-fluxing sinter production has been a subject of active interest to iron metallurgists in North America. Accomplishments however, have come predominantly from Europe and proper interpretation of these reports requires an understanding of European raw materials and European economics. The technology, of course, can be applied universally.

Jan 10, 1959

By H. M. Ziesemer

PRIOR to 1909 that mountain of porphyry, known as. Sacramento Hill, had remained hardly touched but had always aroused suspicions as to the presence of ore within.. During that year, exploratory work was started by underground methods; drifting and raising continued until 1913. It was proved that a mineralized zone existed, the limits of which had not been determined; so, because of the lower costs of exploratory work and the greater desirability of vertical sections, it was decided to prove the extent of the ore zone by churn drills. Drilling continued until the year 1917, when it seemed almost certain that the horizontal limits of the orebodies had been determined. Ore continued in depth in one direction beyond a point where it was economical to explore by churn drilling; this extension is still being developed by underground methods. The irregularities of the boundaries of the ore zones, together with the variable grades of ore encountered, made it necessary to drill on the corners of 100-ft. squares. Two ore zones were proved, known as the East and West Orebodies. The Sacramento Hill porphyry stock intruded into the Dividend fault. The fault ran roughly east and west with a dip to the south, having pre-Cambrian schists on the north against Paleozoic limestone on, the south. This intrusion was accompanied by a silica breccia on the south periphery, along the limestone contact side. The ore lay in the silica breccia and in the porphyry, some distance from the breccia. No ore was found in the heart of the porphyry mass on the north side, along the schist contact. The West Orebody is elliptic in shape, having a major axis of 1200 ft. (366 m.) and a minor axis of 800 ft. (244 m.); these diminish with depth until, at 300. ft., the axes are 500 ft. and 300 ft., respectively. The ore consists of chalcocite, some bornite, chalcopyrite, and considerable pyrite in a silicious gangue. About 30 per cent. of the copper is caused by

Jan 2, 1922

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By E. G. Leonardon, D. C. McCann

The search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out continuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum of useful samples. A device for taking samples of the formation from the walls of a hole therefore offers the possibility of recovering cores from zones otherwise lost as a source of this type of information. Furthermore, by coring

Jan 1, 1939

By F. M. Simonds, E. Z. Burns

The Rawley property is located in the Kerber Creek mining-district, Saguache county, Colorado, at an elevation of 10,600 ft. (See sketch-map, Fig. 1.) Ore was found in this vicinity as early as 1880, and claims covering a large area were located and in many instances patented. The ores, however, being of comparatively low grade, and the nearest railway station, Villa Grove, being some 20 miles away, it is extremely doubtful whether any considerable amount of ore was ever handled at a profit. It is safe to say that several hundred thousand dollars were spent (a large part in building mills) previous to 1902-03. About that time a very capable promoter gathered together a group of these claims and interested some New York people, who had had no previous mining experience, in the purchase of these claims. Following the organization of a company, this promoter became General Manager. As often happens under such conditions, the first step was to erect a mill to treat 100 tons per day. It may not be fair to this enterprise to say that the failure which followed might have been foretold, simply on general principles, but this much is certain—the water supply fluctuates in the course of a season through a wide range and for a considerable portion of the year was inadequate to run this mill at capacity. Further, it is currently reported that some of the mill foundations were placed on ice. However true this statement may be, it is a fact that, when first inspected by us, many of the belts in the mill were held on'their pulleys by means of idlers. A shut-down followed, with a material re-adjustment of interests, at which time we became consulting engineers for the company.

Jan 1, 1914

By Basil Prescott

Resume.—The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre-mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide type occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore, The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition. Introduction The Santa Eulalia district is situated in the State of Chihuahua, Mexico, and lies about 12 miles southeast of the capital, the city of Chihuahua. (See map, Fig. 1.) The district embraces the Sierra de La

Jan 1, 1915

By H. E. Nold

ThE raw materials of the ceramic industry are mostly clays. This raw material is ground, water is added and the mixture pugged into a moist, plastic, rather stiff mass. From this mass the desired units of manufacture are made (bricks, hollow building tile, sewer pipe, etc.). These units are dried; then placed in kilns and heated until the desired degree of vitrification is obtained. For firing ceramic ware, two distinct types of kilns are used; namely, periodic and continuous tunnel. Periodic Kilns Periodic kilns are those ordinarily seen in a brick plant. They are either round or rectangular. The raw, dried, formed ware is piled or set in the kilns to depths frequently exceeding 10 ft. The kiln is heated until the ware is matured, then gradually cooled sufficiently to allow men to remove the ware; then the cycle is repeated. The time duration of the cycle may be more than two weeks. In order that heat can be distributed uniformly throughout the pile or setting, the units are placed so as to leave open spaces or flues throughout the pile for the passage of the hot gases. Each kiln is provided with a number of fireboxes (usually 10 or 12) spaced equally in the outside wall. The fireboxes may be equipped with flat or inclined grate bars or they may have no grates at all (dead bottom). Down-draft kilns are most used. In these the hot gaseous products of combustion from the fireboxes are deflected upward by bag walls just inside the fire zone. From the top of the kiln the gases are drawn down through the setting, off through holes in the kiln bottom, and conducted to a stack or stacks. In up-draft kilns the fireboxes are usually set somewhat lower. The hot gases are drawn inward and upward through the ware and pass off from the top. Up-draft kilns find their greatest use in the firing of common brick. In either case the problem is to maintain, as nearly as possible,

Jan 1, 1934

I. PRESIDING OFFICERS. At all Business meetings of the Institute the President, or, in his absence, the Vice-President, or, in the absence of both of them, any other member of the Board of Directors to be chosen by the meeting, shall preside. At all other meetings of the Institute the President of the Council or, in his absence, one of the Vice-Presidents, if present, shall preside II. ORDER OF BUSINESS. At each Business meeting of the Institute the order of business shall be as follows 1. Reading of minutes of preceding meeting. 2 Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Election of Members of the Council. 7. Reports of Standing Committees. 8. Reports of Special Committees. 9. Special Orders 10. Miscellaneous business. This order of business may be changed by a vote of a majority of the Members and Associates present in person or by proxy. The usual parliamentary rules shall govern all meetings of the Institute except in cases otherwise provided by the Constitution or the By-Laws. At all sessions of the Institute other than business meetings, the order of proceedings and the time of adjournment, shall rest in the discretion of the presiding officer

Jan 1, 1923