Search Documents

By Charles H. Behre

KEYNOTE of the mining geology sessions was the preparation for an extensive war with all that this implies as to the need for strategic minerals, both metallic and nonmetallic. Nevertheless the sessions also included many papers of less urgent, more theoretical interest. The stress of wartime production had the effect of giving an unusually full and rich program, the longest in recent years, with sessions continuing virtually throughout the meeting. Some papers dealt with geophysical prospecting as applied to mining geology; others were concerned with the grand strategy of mineral reserves and thus involved the industrial minerals; such "borderline" subjects were presented before sessions held jointly with the Geophysics Committee or the Industrial Minerals Division.

Jan 1, 1942

By Clinton M. Young

(Pittsburg Meeting, March, 1910.) I. INTRODUCTION. THE experiments herein. described were carried on in 1908-9 . by the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coal-mines, a subject which is engaging the attention. of numerous investigators. An unusual number of serious disasters has directed to. the subject a study which discloses the disquieting fact that, in the. United States, the ratio of lives lost per ton of coal mined has been on the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in, comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and. a very great increase in the amount of explosive used.. . This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle. West it is not now uncommon for a miner to use six ,kegs (150 lb.) of black powder in a "pay" of two weeks, while within the memory. of men still active, one keg (25 .lb.) would last two men for a " pay." So. great has . the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject. of explosions in coal-mines has. led to the belief . that the use of, large -quantities of explosives, in some cases by slightly-trained men, had not been * Associate Professor- of Mining Engineering, University of Kansas, Lawrence, Ran.

Aug 1, 1910

By AIME AIME

Change of Meeting from Birmingham to Chattanooga. In consequence of the disturbed conditions attending a long¬continued labor strike in Alabama, the meeting of the Institute was changed from Birmingham, Ala., to Chattanooga, Tenn., where it will. begin on Thursday evening, Oct. 1, 1908. Information. of this change bad been sent to the newspapers through the Associated Press, and by circular to all members, when news was received of the sudden and unexpected termination of the strike referred to. It was, unfortunately, too late to change once more the arrangements for the meeting. But it is hoped that the cordial invitation of the citizens of ,Birmingham may be renewed and accepted at a future time, not too remote. Office Facilities for Visiting Members. A separate room in the suite occupied by the American Institute of Mining Engineers on the ninth floor of the United Engineering Society Building, has been equipped with furniture and telephone extension for the temporary use of members of the Institute or of sister societies, or visitors suitably accredited. Members of the Institute visiting New York for a short time, who need office facilities during their stay, or members residing in the city. who need temporary office accommodation, can arrange to have set apart for their exclusive use a room, equipped with office furniture, telephone, etc.,. in the suite of the Institute. It is not the intention to give possession of the room to any individual for an indefinite time, but to offer to members of the Institute an opportunity to acquire a well-located, well-equipped business headquarters to carry on transactions which

Jan 9, 1908

By RUSSELL C. FLEMING

GILSONITE is a brilliant black, tarry-like bitumen, classed technically with glance pitch and graharnite as an asphaltite. As found it is brittle, breaking much like ice, and has a conchoidal fracture. Purest forms are used in the manufacture of paints, varnishes, electrical irisulatiorl, and inks for rotogravure; molded articles such as switch handles, telephone mouthpieces, and but- tons are made from the intermediate grades, and the poorer grades are used for the saturation of felt. According to the U. S. Bureau of Mines figures, production grew from about 4000 tons mined in 1904 to 55,000 tons in 1929. This asphaltic substance is found only in the Uintah basin in northeastern Utah, in veins over a wide area. Veins in the vicinity of Fort nuchesne were first discovered about 18G2, on what was then the Uintah Indian reservation, and the vein matter was originally called Uintaite because of that fact, In the early days, S. H. Gilson. of Salt Lake City, was so persistent and zealous in his efforts to develop the deposits and find a market that the name gilsonite was given to the material. Later, the wider and more renowned wins near Wayson and Dragon, in extreme eastern Utah, became the main supply.

Jan 1, 1932

By AIME AIME

A THOROUGHLY satisfactory crowd turned out at the fall meeting of the Industrial Minerals Division and took an active part in the entire program. On Thursday afternoon, Sept. 24, a limestone plant was inspected, technical sessions occupying the attention of the visitors all day Friday and Saturday morning. Headquarters were at the Nittany Lion Inn, an attractive hostel on the Penn State campus, at State College, right in the center of Pennsylvania. We are still in the dark, despite inquiries, as to just what breed of lions Nittany lions are. As nearly as we could find out, Nittany is not a Biblical name, as it sounded to us, but a corruption of the name of an Indian princess, or maiden, or maybe just girl that haunted those parts in bygone times and after whom a near-by mountain was named. Penn State athletes are "lions" and there you are. The meeting was supposed to be a joint one with the American Ceramic Society's Materials and Equipment Division; but it was quite evident that the Institute had a much better publicity agent than the Society, which bothered Ross. Purdy, the aggressive secretary of the ceramic people, no end. However, Secretary Purdy saw to it that everyone present fully understood that the Ceramic Society was present, so that that contingent all but stole the show, its representatives presiding at every meeting. The Pittsburgh Section of the American Ceramic Society was also supposed to be holding its fall meeting there at the same time, but made no trouble at all for anybody, as one of the speakers remarked.

Jan 1, 1936

By N. O. Gray, John Henderson

Hydrogen-reduction data for naturally occurring single crystals and Prepared polycrystals of dense hematite have been presented. Results cover the temperature range 400o to 1000oC, for particles from ten sources, ranging in size from 0.07 to 10 mm and in shape from spheres to cylinders, cubes, and thin slabs. A consistent pattern of behavior has been demonstrated for single crystals and the reduction mechanism shown to be temperature-dependent. Below 579oC reduction is a simple topochemical process but at higher temperatuves it is complex and occurs in two distinct stages. Prepared particles from these laboratories behave in a similar manner to the single crystals. Data from two investigators showing topochernical reduction of Prepared particles above 575°C are inconsistent with that for other dense hematites. It is concluded that topochenzical reaction should not be used as a model for generalized rate expressions for dense hematites. SINCE 1958, McKewan1-6 has brought to prominence a simple concept of dense hematite reduction. This model is that oxygen is lost from a hematite particle undergoing reduction only from an oxide-iron interface that recedes in such a way that the oxide remaining retains the original shape of the particle, i.e., reduction occurs topochemically. An adjunct to this concept is that any intermediate oxides in the transition from hematite to iron only form thin layers so that oxygen cannot be lost from the particle without movement of the oxide-iron interface. Further, the rate of oxygen loss from the particle is said to be proportional to the area of the receding interface so that the iron layer grows linearly with time and the over-all reduction process can be described by the equation where ro and do are the initial particle radius and density, respectively, R is the fraction of the original oxygen lost, i.e., the fractional reduction, at time t, and K is the rate constant. The idea of an underlying simplicity in hematite reduction is attractive because it gives a tractable basis from which general theories of hematite reduction can be developed and it has received wide support,7-14 based mainly on the large amount of data13 that can be fitted to Eq. [I]. However, despite the fact that this equation has been derived for dense materials, the bulk of the data that have been used to test it13 have been for materials of only about 90 pct of theoretical density (5.26 g cm-3) or less, so that its generality for dense hematites has not been demonstrated. In any case, as will be seen, adherence of reduction data to Eq. [1] does not necessarily imply that reaction occurs topochemically. In this work only data for hematites approaching theoretical density are considered and it will be shown that in only one study besides McKewan's is topochemical behavior observed over the whole range of temperature investigated. For the majority of materials a linear rate of interface advance is observed to complete reduction only when wustite is not a stable intermediate phase in the transition of hematite to iron, i.e., at temperatures below about 575°C. Above this temperature, reduction is an exceedingly complex series of reactions that takes place in two distinct stages and it is only in the first stage that reaction in any way resembles a topochemical process. This means then that, far from representing general behavior as has commonly been supposed, topochemical reaction for dense hematites is only a particular behavior that may be observed under some circumstances. EXPERIMENTAL Hydrogen-reduction data have been collected and cross-checked in these laboratories by three techniques, weight loss, collection of water evolved in the reduction reactions, and direct metallographic examination. Details of these techniques are discussed elsewhere," where it is shown that results obtained by the three methods are in close agreement. The weight-loss method, by which most of the results were obtained, consisted of hanging the sample in a platinum mesh basket from an Ainsworth Model AV-AU-1 vacuum recording balance inside a vertical l 1/4-in.-ID alumina tube furnace. Dry deoxidized hydrogen was flowed downwards through the tube at 2 to 4 liters min-1 (stp). Single crystals from two sources and artificial oxides from three sources have been examined. The single crystals were from hematite deposits at Yampi Sound, Western Australia, and Brazil, the latter being obtained from Gregory, Bottley and Co., London, U.K. The "Yampi Blue" crystals were hand-picked from washed, magnetically concentrated, sized fractions, -200 mesh BSS (mean diameter ca 0.07 mm) and —36 + 44 mesh BSS (mean diameter ca 0.4 mm) while 10-mm cubes were cut from the Brazilian crystals with a diamond saw. The starting materials for the prepared particles were hematites designated, respectively, "Specpure Iron Oxide", Laboratory No. S639 from Johnson Matthey & Co. Ltd., London, U.K., "Calcined Ferric Oxide" from B.D.H. Laboratory Chemicals Division, Poole, U.K., and "Pigment Grade Oxide", EPR-50, from C. K. Williams & Co., Easton, Pa., U.S.A. Approximately spherical particles were prepared from the artificial oxides by rolling the material, moistened if necessary, in a glass jar, and cylindrical compacts approximately 10 mm in diam and of approximately equal height were pressed in a steel die at 200 psi. These spheres and cylinders were subsequently fired in oxygen for 20 to 100 hr at 1370°C. The

Jan 1, 1967

By R. F. Domagala, M. Hansen, D. J. McPherson

On the basis of metallographic analysis, incipient melting data, thermal analysis work, and X-ray diffraction, phase relationships in the 0 to 50 atomic pct alloy content were carefully resolved. Phase relationships in the higher alloy content regions were outlined. A single intermediate phase, peritectically formed, of the form ZrX2 was established in each system. A eutectic and a eutectoid were found in the zirconium-rich region of both systems. Appreciable solubility of molybdenum and wolfram was found in ß zirconium, but only a slight solubility in a zirconium. PREVIOUS work on these systems was limited to X-ray investigations of the intermediate phases1, 2 and preliminary surveys of the zirconium-rich alloys." The diagrams presented were determined principally by metallographic, thermal analysis, and incipient melting techniques. In accordance with the Atomic Energy Commission contract requirements, phase relationships up to 50 atomic pct molybdenum or wolfram were carefully resolved, while only a limited amount of work was done to outline the 50 to 100 atomic pct alloy region. A description and analysis of the metals used in the preparation of alloys for this study are included in Table I. A "low-hafnium" zirconium crystal bar, produced by the decomposition of a volatile iodide onto a hot filament, was employed for these studies. Westinghouse "Grade 3" crystal bar was used for all alloys. The zirconium, as received, was coated with corrosion product from a standard autoclave test by which its grade designation is determined. This was removed by a sand-blasting and HF-HNO, pickling technique developed by the Atomic Energy Commission. The bars were cold rolled to approximately 1/32 in. sheet, pickled for iron removal, sheared to 1/4 in. squares, washed with acetone, and stored for furnace charge. Molybdenum sheet. 0.003 in. thick, 0.001 to 0.005 in. wolfram wire, and M in. wolfram rod crushed to granular form, from Fansteel Metallurgical Corp., were used as alloying stock. Melting Procedure A nonconsumable electrode arc furnace identical to that described in detail by Hansen et al.4 was used. The source of power for melting Zr-Mo alloys was a 400 amp dc welding generator, while a 900 amp dc generator was used for preparing Zr-W alloys. Electrode tips of the same material as the alloy addition were employed in both systems, i.e., molybdenum tips were used for Zr-Mo alloys, and wolfram tips for Zr-W alloys. This precluded any possible electrode contamination during arc melting. Ingots of 20 to 30 g of Zr-Mo alloys were melted under high purity helium in the cavity of a copper block insert in a spun copper crucible. Homogeneity was insured by remelting all ingots four to six times without opening the furnace. Due to the large difference between the melting points of wolfram and zirconium, direct melting of the charged metals as above generally yielded ingots containing unmelted wolfram particles. This was overcome, after many variations in technique, by melting a pure wolfram charge at high power levels (700 to 900 amp) and slowly adding zirconium to form a master alloy. Such master alloys were sectioned and remelted several times, then crushed to serve as melting stock for alloys of lower wolfram content. Master alloys containing 26, 50, 52, 70, and

Jan 1, 1954

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By G. M. Lee

SEVERAL improvements have been made in Granby smelting practice since the company abandoned the direct smelting of raw ore in the blast furnaces in June, 1927, in favor of sintered concentrate. These improvements have been made in several fields, but the most novel and outstanding change was the development of a process of concentrating most of the gold, and a somewhat smaller fraction of the silver present, in a small portion of the blister copper produced. The practice of making "copper bottoms" is usually associated with the reverberatory smelting of copper ores containing high percentages of impurities, or of copper matte high in precious metals. It has for its object, in the one case, the production of a major part of the copper relatively free from impurities and, in the other case, the production of a small per¬centage of the copper carrying the major part of the precious metals. Although the blister copper produced at the Anyox plant of the Granby company is remarkably free from deleterious impurities and normally contains no great amount of precious metals, certain economic considerations made it advisable to concentrate the existing precious metals into a relatively small percentage of the blister copper produced. The process devised took advantage of principles and reactions of the usual bottoms processes, but was carried out in the converters instead of in a reverberatory furnace.

Jan 1, 1935

D. M. Riordan has been appointed a member of the Institute Com¬mittee of the Engineers' Reserve Corps movement. Our Committee, therefore, now consists of Henry S. Drinker, Chairman, Messrs. Arthur S. Dwight, Warren A. Wilbur and D. M. Riordan.

Jan 1, 1916

By M. A. Grossman

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a "pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain size may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of unhardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of o.-2o per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybdenum when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as would appear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.2o per cent Mo provides a factor of 1.63, an increase of over 6o per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added "20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater harden ability will be obtained by using, for example, o.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost 10 per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome-molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By M. A. Grossmann

THE hardenability of most steels can be predicted within 10 to 15 per cent provided the complete chemical composition is known, including "incidental" elements; and provided the as-quenched grain size is known; and provided, finally, that the composition and heating temperatures for hardening are such as to result in austenite free from carbide particles. In method proposed herein, the steel is considered as having a base hardenability due to its carbon content alone (the hardenability of a ''pure steel" of the given carbon content, without any other elements), and this base hardenability is multiplied by a multiplying factor for each chemical element present. After multiplying all these together, the final product is the hardenability. Grain sue may be taken into account either in the base hardenability or after the multiplication. Hardenability is stated in terms of "ideal critical diameter"; namely, the diameter of bar, in inches, that will just harden all the way through (absence of un- hardened core) in an "ideal" quench, and the calculation may also be related to the Jominy test. The data bring out certain features rather clearly. For example: I. It is quite useless to attempt to predict hardenability unless all elements, including "incidentals," are known; thus an "incidental" chromium content of 0.20 per cent increases the hardenability by about 50 per cent. 2. The relative effectiveness of different alloys is sometimes unexpected; thus molybde- num when calculated in this way appears to be of the same order of effectiveness as manganese, rather than much more powerful as wouldappear to be common experience; observe that an increase from no manganese to 0.20 per cent Mn provides a multiplying factor of 1.67, and an increase from no molybdenum to 0.20 per cent Mo provides a factor of 1.63, an increase of over 60 per cent in each case. However, if to a steel containing 0.50 per cent Mn there is added " 20 points of manganese," the factor is raised from 2.65 (for 0.50 per cent Mn) to 3.35 (for 0.70 per cent Mn), or an increase of only 26 per cent. Thus the first small addition of an element has a much more powerful percentage effect than an equal further addition when some is already present, and in most cases the effect of molybdenum is considered in relation to a steel in which molybdenum is absent. 3. If two elements are equally effective, a greater hardenability will be obtained by using, for example, 0.5 per cent of each than by using 1.0 per cent of either of them alone. 4. A knowledge of the as-quenched grain size is essential for precise work, since a difference of only one grain size number (say No. 7 instead of No. 6) makes a difference of almost lo per cent in hardenability (in these units); this, however, does not apply to certain steels of high hardenability. It should be emphasized that in chromium steels (over 0.30 per cent Cr) and chrome- molybdenum and chrome-vanadium steels, undissolved carbides are likely to be present in the steel as quenched, and that in such cases the charts can indicate only a maximum possible hardenability, whereas the extent of hardening actually obtained may be much less. Thus tests on a number of chrome-molybdenum steels have indicated a degree of hardening amounting to only 50 to 65 per cent of the maximum possible, and in chromium steels from full hardening (100 per cent) down to as low as 70 per cent. On the other hand, when the amount of such elements is small (Cr under 0.30 per cent, Mo up to 0.25 per cent in the absence of Cr, and V up to 0.04 per cent), the charts provide reasonable approximations. The precise figures on the charts are suggested as tentative, subject to some modification as more data accumulate, but the fundamental concept appears to be supported by tests made on a wide variety of steels, a few of the correlations being shown in Fig. I.

Jan 1, 1942

By J. A. Richardson

J. A. RICHARDSON[t]-Mr. Stuckey's account of the geology of the kaolins of North Carolina suggests that they exhibit some features similar to those of the Malay Peninsula. About one half of British Malaya (some 26,000 square miles) is occupied at the surface by igneous rocks, of which granite and its associated derivatives constitute fully 90 pct. The average granite is a biotic variety. It is predominantly potassic but carries, in addition, notable amounts of soda and lime so that albite and albiteoligoclase are generally common constituents of the rock. The minor derivatives from granite "magma" likewise include potassic and sodi-potassic members. Decomposition of the granitic rocks has led to the formation of kaolin in many localities, but, in general, the deposits are rather small and, at present, none is exploited commercially. True primary or residual kaolins (as defined by Stuckey; p. 48 Vol. 173, p. 2 TP 2219) have been developed from feldspar veins, pegmatites and from other granitic differentiates which cut through the larger masses of granite; they are usually small and narrow. Kaolin has been derived from aplite, quartz porphyry, quartz micro-porphyry, felsites and microgranites belonging to a complex known as the Chegar Perah-Pulai intrusion in northwest Pahang and southwest Kelantan. The bulk of the component rocks has been more or less strongly sheared. Kaolin-like end products have been formed from both sheared and nonsheared varieties. Kaolin has been formed also by the complete breakdown of trondjemite flanking the northwestern and western margins of the complex Bukit Ranjut syenite intrusion in northwest Pahang. These trondjemites range in composition from essentially quartz-free albiteplagioclasites to quartz-free microcline rocks; they are, in effect, the syenitic homologues of white sodic and potassic granite-aplites. The granites in Malaya have generally undergone more or less severe surficial weathering leading to the production of a spongy and rather cellular or a soft "mealy" material (sandy clay) down to depths of about 100 ft; in places the granite is strongly decomposed down to 150 ft. There has occurred, therefore, widespread partial kaolinization, but, in general, no extensive deposits of good quality kaolin seem to have been formed by these processes of decay. Frequently, the katamorphic processes of desilicification have advanced beyond the production of kaolin towards the formation of lateritic end products. The more important Malayan kaoiins seem to be confined to the western alluvial plains, particularly in areas either where granite crops out at surface, or where it forms the bedrock of the alluvium. There are numerous excellent examples around Gopeng and elsewhere in the Kinta Valley of Perak. Such kaolins belong to Stuckey's groups of secondary deposits, and, like them, these also may be bedded. Field observations have established the existence of what for want of a better name is referred to by the Malayan Geological Survey as "granite wash." It is believed that granite, undergoing extensive deeply penetrative and probably rather rapid destruction under humid tropical weathering (temperature around 90°F; rainfall about 100 in. per annum; high humidity) "flowed," was moved by "creep" and, in addition, probably slumped in large waterlogged masses of sandy clay from topographic salients onto the adjacent flats. Either during this period of transmigration or later when the sludged granite detritus, after having more or less come to rest, was attacked by flowing water, differential sorting and erosion took place with the result that the resorted debris was moved and later deposited as bedded alluvium. In this way, banded "granite wash" was produced comprising alternating bands of clayey sand (resorted granite sludge) and white

Jan 1, 1947

By Kent R. Van Horn, W. P. Sykes

Since Honda and Murakamil in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450° C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450" and 1000" C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000" C. and heated for 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt's second intermediate phase. While Takeda failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200" and 1450" C. no evidence of the second phase (Fe2W) was observed 'either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1933

By Henry G. Granger

NOTHING in this paper is to be understood as even suggesting a moment's suspension of the splendid work now going forward on the Isthmus of Panama, except so far as it is related to the proposed locks. All the work already done, and all material purchased or ordered, would be available for the plan herein proposed. The situation and the problem concerned may be summarized as. follows : The scheme of a lock-canal through the Isthmus of Panama was adopted, as is well known, on two principal grounds-namely, the greater expense of a sea-level canal, and the longer time required for its construction. Of these, the latter is believed to have been the more influential. But further developments have diminished the weight of both, so that a reconsideration of the question is warranted. It is the purpose of this paper to advocate such a reconsideration-emphasizing the importance of certain objections to the lock-canal not mentioned or not duly appreciated in the report of those members of the International Board of Consulting Engineers who favored this form; showing the nature and bearing of the new facts developed; and, finally, proposing a combination of well-known methods and apparatus, which would, in my judgment, effect the construction of a sea-level canal in less time, and perhaps at no greater cost, than will be required for the remaining work on the lock-canal. I. OBJECTIONS TO A LOCK-CANAL. 1. Earthquakes. Two centuries ago Panama is said to have been destroyed by an earthquake. In 1882 a rather violent earthquake was felt at the southern end of the Isthmus. In 1898 I felt a slight shock near the present border-line of Colombia. In 1900 I felt three shocks at Quibdo, the head of navigation of the

Jan 1, 1909

By L. W. Rowe, S. S. Cole

A laboratory bench scale unit is described whereby finely divided chlorinatable residues are held for a short period by a restraining bed of a coarse-grained ore of comparable composition to permit 'flash' chlorination of the high surface area powder. Results on chlorinating a finely divicled titania residue using rutile sand as the restraining bed showed that 92 pct utilization of chlorine and equivalent conversion of TiO2 in the fine residue to Ticl4 were attained with a dust loss of about 3 to 4 pct and an equivalent amount of ch1om'nation of the titanium values in the restraining bed. THE chlorination of coarse grain titaniferous ores; i.e., 20 to 150 mesh sizes in fluidized beds is practiced commercially.' One effective method found for the chlorination of a very fine material in a fluidized bed is the "flash" chlorination technique.' By charging the finely divided charge material into the bottom of an established bed of optimum sized rutile, ilmenite, titanium beneficiate, or even an inert material such as sand, chlorination occurs before the dust can pass through the bed. The major requirement is that the bed be less chlorinatable than the charge. In this process, the charge consists of a finely divided (between one and 50 µ) titania residue obtained from a titaniferous ore beneficiation process. The charge is blended with a 20 pct wt basis addition of 20 to 60 .mesh size low volatile coke (to minimize hydrogen chloride formation) and fed to the bottom of the bed with the chlorine gas stream. A ball check device is used to permit entry of the charge and prevent the bed from discharging when the gas flow is cut off. The coarse pieces of coke serve to reduce compaction in the charge mixture and permit sat]sfactory feeding without plugging or jamming. Feed and gas rates are adjusted to provide for complete reaction of the charge material, with 90 to 95 pct chlorine efficiency, and maintain a gas flow in the range of 0.4 to 0.6 ft per sec. The equipment consisted of a 3-in. diam mullite tube enclosed in an electric furnace. A bow-shaped 3/4 in. Saran tube fed the charge from an air lock type of feed hopper (to prevent the escape of the chlorine gas into feed bin) to the bottom of the bed. The charge rate was set by providing a small awiliary hopper below the feed hopper where a weighed portion of the charge could be discharged in a specified time interval into the main chlorine stream. The chlorine rate was measured by a flowmeter. The reaction tube was filled with a bed of Australian rutile ore, this restraining bed serving two purposes; i.e., it rapidly heated the fresh charge to the reaction temperature and retained the particles in the bed for a sufficient time for selective chlorination to proceed. Due to the fine particle size and open, porous structure of the charge, this reaction was almost instantaneous, and, with proper adjustment of feed and gas rates, very little fine material passed through the bed without reacting and only a very small fraction of the restraining bed was chlorinated. A typical reaction procedure was to fill the bench scale fluidized bed unit with a 1 kg charge of Australian rutile ore analyzing 95.5 pct TiO2, 0.6 pct FeO, a beach sand deposit 40 to 150 mesh size. When fluidized, the bed was approximately 2 ft in depth. The ore was fluidized with a 1:l mixture of chlorine and nitrogen at a rate of 0.40 ft per sec. This gas mixture was necessitated by the comparatively short bed depth; a larger unit, with a deeper bed, could be fluidized with chlorine alone without significant free chlorine loss. Feed rate was 8.0 g per min of beneficiated ilmenite analyzing 85.0 pct TiO2, 2.6 pct FeO plus 1.6 g per min of 20 to 60 mesh petroleum coke. The

Jan 1, 1962

By J. M. GLEDHILL

IT would doubtless have been felt by many but a few years back that there was little left to be said on the subject of crucible tool-steel, and that something akin to finality had been arrived at in its manufacture and general treatment. Probably such feeling was justifiable when it is remembered that the making of steel in crucibles is by far the oldest method known, dating back from time immemorial, it being indeed impossible to accurately trace its origin and earliest development; but it seems certain that carbon-steel was made and used thousands of years ago for cutting-tools. Proof of this may be seen by the marvelous carvings and workings on the intensely hard stone-work of the ancients, for it would be difficult to conceive by what means, other than with steel tools, such work could have been executed; and it is wonderful to contemplate that steel cutting-tools should have been used so long ago, whilst the principle of manufacturing them-that is, by fusion of iron and charcoal in crucibles-was then in a measure on the sane lines as we work on at the present day. Archaeologists have discovered that the Chinese made steel in crucibles long before the Christian era. " Wootz " steel fabricated in India centuries ago was crucible steel, as was also the celebrated Damascus steel, produced at the forges of Toledo, and, curiously, this latter steel furnishes' yet another proof that "There is nothing new under the Sun," for it is recorded that Damascus steel contained certain percentages of tungsten, nickel, manganese, etc., some of the very elements, in fact, contained in the present modern high-speed steel, so that a latent high-speed steel may be said to have existed

Mar 1, 1905

By M. H. Yoo

Possible interactions of the perfect dislocations of six slip systems or the c dislocation with the (10i2f (ioii), {ioIi}(ioiZ), {1122}(1123), and {1121}(ii26) type twins in hcp metals have been analyzed from the crystallographic and the energetic points of view. Twenty-six distinct types of possible interactions were identified, and those selected based on crystallographic constraints were examined for their energetic feasibilities by use of the anisotropic energy factors. No long-range elastic interaction exists for a dislocation when its Burgers vector is parallel to the twin interface. Under a suitable applied stress, a screw dislocation can cross slip at the twin interface. For basal mixed dislocations in cadmium and zinc, the interaction with {1012} twins is found to be attractive, indicating that incorporation of these dislocations into the twins is energetically feasible and that twin growth will result. On the other hand, the interaction between both basal and Prism mixed dislocations and the {1012} and (1121) twins is found to be repulsive in Mg, Co, Re, Zr, Ti, Hf, and Be. This indicates that under an applied stress a local stress concentration will develop due to a dislocation pileup at the interface, which may result in a site for either the nucleation of other twins or the formation of a crack, depending on the cleavage strength. WHEN a metal undergoes plastic deformation, a certain configuration of slip dislocations will result in a state of dislocation pileup against an obstacle. The stress concentration thus developed may enhance the process of twin nucleation and also twin growth. Furthermore, once formed and dispersed in the crystal, twins can act as effective barriers against slip dislocations. The degree of such mutual influence or interrelation between slip and twinning is generally known to be pronounced in the case of hcp, metals. It is also known that deformation by twinning occurs more commonly in hexagonal metals than in cubic metals. In fact, under suitable stress states, all hexagonal metals exhibit {1012) <1011> type twinning.&apos; In addition to this common type, deformation by (1151) <1126> type twinning occurs in zirconium, titanium, and rhenium, which show remarkable ductility.&apos; The importance of twinning during general deformation to the ductility of hcp polycrystals has been briefly discussed in recent review works.2&apos;3 The purpose of this paper is to analyze the interaction between slip dislocations and twins in the hcp structure and to discuss the nucleation and growth processes of twinning and the role of twinning in the <"°" noil) o, 1/3[112O] (OOO2) 1/3[1123] Fig. l—-Slip systems in hcp structure. ductility of hexagonal metals. The problem will be discussed from the geometric and the energetic points of view in a manner similar to that of the previous work on zinc.4 Since hcp crystals deform by several slip and twin systems, numerous interactions result as possibilities. The Burgers vectors of six slip systems and the c dislocation shown in Fig. 1 and the four twin systems listed in Table I are considered here. A complete tabulation of the possible interactions is followed by discussion of those that are more likely to occur on the basis of crystallographic constraints and energetic considerations. 1) CRYSTALLOGRAPHY OF TWINNING The crystallographic elements, K1, K2, n1, and n2, for the four compound twin systems are now well established.= A unit cell with the base vectors n1, and n2 is shown in Fig. 2 for each twin system. The unit cell before twinning is shown in solid line, and the corresponding unit cell after twinning is shown in dashed line. Also shown in Fig. 2 are the following crystallographic parameters: S is the plane of shear, d the interspacing of the twin habit planes K1,Ø Iis the acute angle between n1, and n 2, e is a numerical factor, and q is the number of K, lattice planes intersected by 17&apos;. These parameters can be expressed in terms of the axial ratio, y = c/a, as listed in Table 11. The macroscopic shear strain of twinning, s, and the magnitude of a "unit twin dis-l~cation,"4 bt, are also expressed in terms of y and given in Table 11. In Table 11, K1 and q1 are given in both Miller-Bravais and Miller indices. In double lattice structures, shuffling of atoms in addition to a homogeneous shear of the lattice is generally required if the original crystal structure is to be restored after twinning. The extent of current understanding on this problem of atom shuffling is per- Table I. Four Twin Systems in Hcp Structure

Jan 1, 1970

By R. M. S. B. Horta, W. T. Roberts, D. V. Wilson

Evaluation of results obtained by the Harris method for inverse pole figures is discussed. Two existing analyses and a new approach are compared. In the most frequently used analysis, different reflections are accorded equal weight. A second method involves area-weighting of reflections, mainly to take account of nonuniformity of Pole distribution. In the new method, reflections are weighted according to their multiplicity factors. Intensity ratios obtained from a sample of steel sheet by the three methods are compared. INVERSE pole figures offer a convenient method of depicting the proportions of material with various orientations referred to a unique specimen axis. The technique was first applied to fiber textures, but it is now frequently used as a description of texture in sheet metal, the unique axis in this case usually being the sheet normal. The Harris method&apos; for the determination of inverse pole figures has the great merit of simplicity. It suffers certain intrinsic limitations, but provided that these are borne in mind, the results allow useful conclusions to be drawn regarding the effects of texture components on certain mechanical properties. Much thought has been given to alternative methods of texture description, aimed at eliminating the ambiguity in the simpler methods.2"6 Refinements in the method of description are obtained at the price of increasing complexity, and it seems clear that a simple method, such as that of Harris, will continue to find application. The original derivation by Harris1 has been corrected by Morris7 and later by Mueller, Chernock, and Beck.2 Since the latter reference is more accessible, it is referred to more frequently than the work of Morris. Most users of the inverse pole figure method present their results on the basis of the treatment by Mueller et al., and it is the purpose of the present communication to comment on this treatment and to suggest a simple modification to the method of presentation which enhances the meaningfulness of the results. It will be convenient first to summarize the Mueller analysis as follows: The intensity Ihkl of a hkl reflection from a textured specimen is: Ihkl=CI0AL\Fhkl\2NhklPhkl [1] where C is a constant for a given sample I, is the intensity of the incident beam A is an absorption factor. With usual diffrac-tometer geometry and a flat specimen, A is inversely proportional to the density of the specimen. L is the Lorenz polarization factor Fhkl is the structure factor for the hkl reflection Nhkl is the multiplicity factor phkl is the fraction of crystals in the polycrystal-line aggregate with any particular (nkl) plane parallel to the surface. The corresponding equation for a specimen with randomly oriented grains is lR,hkl=CRl°ARL\fnkl\2Nnklk [2] the subscripts R indicating the factors that are different for the random sample, which will, in general, have a density different from that of the textured one. The intensity ratio is hkl , c A Phkl [3] IR,hkl CR AR PR The constants are eliminated by summing over all the measured reflections ^iRMi °R AR PR ljPkkl and from Eqs. [3] and [4] T IR,hkl The only unknown in Eq. [5] is Yj phkl and before this can be evaluated, it is necessary to adopt some form of normalizing procedure. Mueller et al. assume that when a large number, n, of reflections is used, the average value of p as defined by Eq. [6] below will be unity ? = £j**l3l [6] and the final result of their analysis follows: hkl Pkkl = i I&Jf~ [7] ±y* Ihkl ^ in,hki The normalizing procedure used by Mueller et al. involves an unrealistic assumption since it gives equal weight to each of the hkl reflections. Other normalizing procedures can now be examined with a view to selecting a more appropriate one. For an infinite number of reflections, the function p can be averaged over a continuous range of orientations covering the complete solid angle 4p by the integral relation: p =1 jp(a)dQ = l [8] This is the only exact procedure, but in practice a

Jan 1, 1970

By James Douglas

IN discussing the waste upon which hinges, or is supposed to hinge, so largely the preservation of our national resources, the conclusions reached would be more reliable if actual ex¬perience were consulted, and fewer deductions were drawn from general statements, which are often the product of the imagination. It cannot be questioned that the value of by-products has not been sufficiently appreciated by us, and that our, tardiness in recovering the useful ingredients of the escaping gas of our coke-ovens is one of the most glaring instances of shortcoming in that direction. And yet even for that sin there is some palliation in the immature condition of affiliated industries. I presume that it is admitted, without argument, that, except under very exceptional conditions, all the elements cannot be recovered from most of the ores or natural products. which we treat. While it is a shame that the by-products from our coke-ovens should be dissipated, Edward W. Parker&apos;s report to the U. S. Geological Survey for 1906&apos; supplies a fairly good excuse in justification of this appalling waste. He says (pp. 773 to 774.)

May 1, 1909