Search Documents

By John Freeman

THE tensile properties of steels at elevated temperatures have been studied by numerous investigators,1 primarily for the purpose of determining their suitability for structural uses. Tests with this objective have been confined largely to the temperature range of approximately 20° to 500° C., because of the rapidly decreasing tensile strength at the latter temperature. Tests have also been extended to higher temperatures for the purpose of determining the most suitable forging range. This temperature range is also of theoretical interest. The phenomenon of increased tensile strength and decreased ductility in the so-called "blue-heat" range, approximately 200° to 300° C., is well known. It was suggested to the Bureau early in 1926 that a study of the properties of rail steels in this temperature range might prove of interest in relation to the studies of transverse-fissure failures in rails. There were available from another investigation3 several new rails from several different heats made to approximately the same specification requirements, the complete manufacturing histories of which were known. It was decided to determine, at least in the preliminary series of tests, only the ultimate tensile strength, elongation and reduction of area, because of the difficulty, time and cost involved in determining the proportional limit and yield point at elevated temperatures.

Jan 1, 1930

By Paul R. Dingess, Edward H. Hare, Douglas C. Brockie

Mining in the Tri-State district of Missouri, Kansas, and Oklahoma has been nearly continuous from about 1848 until the present day, although the major activity was from about 1880 to 1955. The district, which has produced over $2 billion in zinc and lead concentrates, ranks as one of the greatest mining districts in the world. Unlike other Mississippi Valleytype deposits in the United States, which occur in Cambrian and Ordovician limestones and dolomites, the Tri-State district ores occur in Mississippian limestones containing abundant chert. Zinc is 5 to 6 times more abundant than lead. In the Picher Field, the principal sub-district which has accounted for 61 percent of the total district production, most of the ore has been mined from the single horizon, M bed. Most ore bodies, other than those of the "Sheet Ground" or blanket-type, are in large, essentially flat-lying breccia zones and have a definite mineral zonal pattern. An irregular, generally elongated central dolomitic core is surrounded progressively outward by the main ore run, the jasperoid zone, the muddy or shaly and bouldery zone, the sparry calcite limestone zone, and the fossiliferous, dominantly crinoidal, limestone zone. Some of the zones may be absent or nearly so and may overlap to some extent with an adjacent zone. Although the district has been studied by many authors, much controversy still exists about such items as genesis, paragenesis, and time of emplacement. These subjects are discussed in the paper.

Jan 1, 1968

By GORDON H. FISHER

During the year 1945, the drilling pace in West Texas increased above that in the year 1944, and represented the highest number of well completions since 2941. The 1680 new wells drilled 8,287,958 ft. of hole for a per well average of 4933 ft. This depth is approximately 30o. ft. deeper than the average for the year 1944. Although the deepest well drilled in West Texas (Phillips Petroleum Company's Ada Price No. 1, in Pecos County) was completed during the year. 1944 to a depth of 15,279 ft. and tested the Ellen-burger horizon, the producing depth record for West Texas was set during the year 1945 with the completion of Amerada Petroleum Corporation's Jones No. I-A, in the Jones Ranch field, Gaines County, which now is producing at 11,422 ft. from the Devonian formation.

Jan 1, 1946

By F. Ernest Brackett

Much new data on the flow of gases have been discovered by recent experiments by the United States Bureau of Mines and others. Although additional investigation is still desirable, the information now collected seems sufficient to attempt a tentative coördination of the friction factors. This study is confined entirely to fluid friction when the density throughout the duct is so nearly constant that it may be so considered. In the subsequent discussion the following notation is used: v = mean velocity of fluid in duct, feet per second. v' = mean velocity of fluid in duct, meters per second. R = hydraulic radius of duct, feet. R' = hydraulic radius of duct, meters. S = the hydraulic slope. P = pressure absorbed by friction, pounds per square foot. p = pressure absorbed by friction, pounds per square inch. p' = pressure absorbed by friction, kilograms per square centimeter. A = sectional area of duct, square feet. O = perimeter of duct, feet. L = total length of duct, feet. L' = total length of duct, meters. d = diameter of a cylindrical duct, inches. w = density of the fluid, pounda per cubic foot. g = specific gravity of the fluid compared with water = w % 62.4. C, k and B, coefficients for formulas using English measures. C' = metric coefficient, v' = C'R'S. n = coefficient of roughness for English or metric units. The basic formula for the flow of all fluids at constant density appears in the three following forms, which may be denominated: (a) The slope formula, v = CRS (b) The ventilation formula, " n = (c) The pipe formula, C is Kutter's coefficient, which is extensively applied to the flow of water in ducts and channels of all kinds; E is Atkinson's coefficient, used principally with air in ventilation problems; B is a coefficient conveniently adapted to studying the flow of water, gases and vapors in pipes. 312

Jan 1, 1927

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By William Hurst

THE content of this paper is a presentation of the diffusivity theory for the calculation of the water drive on an oil reservoir in which b the history of reservoir pressure with time are the essential parameters for the determination of the rate and cumulative water encroachment into a field. The paper is divided into two parts-the main portion and appendix. The main body is essentially the application of the principles underlined here to actual field data. It consists of the work plots of the radial-flow case, and includes a discussion of an illustrated problem for which the water-drive calculations are treated in conjunction with the volumetric-balance equation. The appendix is a mathematical treatment of the linear, radial, and spherical cases of water influx into a reservoir.

Jan 1, 1942

By Walter L. Maxson, Fred C. Bond

THIS paper is a continuation of two earlier papers, l, 2 and presents new data on the grindability of various ores and other materials-the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRINDABILITY OF VARIOUS ORES This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at x6-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1 ½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1938

By R. B. Hoy, Stanley J. LeFond, K. Reckling

World production of natural diamonds prob¬ably exceeds 50,000,000 carats a year. The Republic of Zaire is the leading producer, with an output which is primarily industrial rather than gem grade. The USSR ranks second, and the Republic of South Africa third. Diamonds are also mined in South-West Africa, Angola, Ghana, Sierra Leone, and other African coun¬tries. In the western hemisphere, Brazil and Venezuela are the principal producers (Fig. 1). A very small output of diamonds is mined today in India, which was the first source of commercial production. In the U.S., efforts at commercial diamond mining have been con¬fined to a small area near Murfreesboro, Ark. The first diamond was found in a kimberlite pipe there in 1906. Small-scale trial mining has not, however, proved economical. Since diamonds were first discovered over 2000 years ago, only about 130 tons have been mined. In order to obtain 1 g (5 carats) of diamonds, it is necessary to remove and process approximately 25 tons of rock. Recovering this small percentage involves a combination of highly developed techniques in mining, quarrying, and earth-moving, and extremely sophisticated recovery processes. End Uses Diamonds are used for two unrelated end uses; gem diamonds are jewels of great beauty while industrial diamonds are essential ma¬terials of modern industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic indus¬trial diamonds are now of a quality that per¬mits wide substitution in the fine-grained sizes. Gem Diamonds A diamond is a natural prism. It has the ability to bounce light rays (reflection), to bend them (refraction), and to break them into all colors of the rainbow (dispersion). This ability to "modify" light gives the diamond three characteristics for providing beauty. First is brilliance, the reflection of light back to the eye. Second is fire, dispersion of light into the colors of the spectrum. Third is scintillation, the "twinkling" that occurs when the diamond is moved (Bauer, 1969). The skill of the diamond cutter is required to unlock the brilliant, fiery beauty of a gem dia¬mond (Fisher, 1966). Diamond-cutting skills have gradually developed over the centuries. The first cutters, in India, learned how to grind one rough diamond against another to remove their "skins" and to give them various shapes. This revealed some fire and beauty, but little compared to that of the diamonds that are cut today. About 1475, a Flemish cutter named Van Gerquem discovered that diamond dust on an iron wheel would polish facets on a diamond to provide more brilliance and fire. Cutters continued to experiment with facets, and shortly before 1700 a Venetian cutter named Peruzzi developed the 58-facet brilliant cut. With the development of the science of optics, cutters have learned more about the behavior of light within the diamond. Early in the 20th century, they learned how to angle Peruzzi's

Jan 1, 1975

By W. G. Fischer

Basic laboratory tests on trona and the surrounding shales initiated the Rock Mechanics program. The stress-strain curve, modulus of elasticity, Poisson's ratio, the uniaxial rock strength, Mohr's envelope, the biaxial stresses at failure, and creep were investigated. A series of underground problems were then approached using this information and various field measuring devices, most of which were developed by the Bureau of Mines. Initially, stress concentrations near mine openings were evaluated using the stress relief technique. This required an accurate determination of the pre-mining stress field. Later, stress concentrations associated with the cave line were studied. After about 30 stress reliefs over an appropriate time interval the effects of one type of mining could be compared against another. The microseismic technique was used to investi- gate a possible application of warning devices near the cave line. A study of mine reorientation was made. Problems related to the shape and size of pillars and barriers were studied. The effectiveness of roof bolting patterns was examined. Control of roof stresses was attempted. A new system of mining in heavy ground has been developed using the information secured in the Rock Mechanics program. Without this system, mining in more than one instance would have been next to impossible. Indeed, from this one discovery alone, the Rock Mechanics program has paid off in improved safety as well as in dollars. The Westvaco trona* mine is located near the town of Green River in the southwestern corner of Wyoming. It is owned and operated by FMC Corp. on land leased from the US Government, the State of Wyoming, and the Union Pacific Railroad. A conventional room and pillar system is being used, (Fig. 1) with complete removal of the pillars during final mining. Return air bleeders surround

Jan 1, 1964

By J. Q. Ehrgott

INTRODUCTION The U. S. Army Engineer Waterways Experiment Station (WES), under sponsorship of the Defense Atomic Support Agency, has recently developed a unique dynamic high-pressure triaxial testing device (DHT). The device permits acquisition of both axial and lateral deformation data while undisturbed soil and/or rock specimens are subjected to various states of controlled impulsive-type stresses produced by varying both the axial stress and the radial stress rapidly with time. The device is used to develop controlled dynamic pressure pulses within the triaxial chamber fluid on soil or rock test specimens to 3 inches in diameter. Controlled dynamic axial pulse loads are delivered to the specimen by a piston driven by an existing pneumatic ram loader (SECO). The DHT consists of a triaxial cell and a pressure supply and decay system which permits the chamber pressure to be varied with time. Together the DHT and SECO operate in a testing program so as to provide time varying confining pressures and axial loads to test specimens at independently controlled but synchronized programmed rise, hold, and decay times. Rise time is defined as the time from zero load or pressure to peak load or pressure; hold time is the time of constant peak load or pressure; and the decay time is the time from peak load or pressure to zero load or pressure. The maximum dynamic confining pressure attainable is approximately 15,000 psi and the fastest rise and decay times are 3 millisecond (msec) and 20 msec, respectively. This paper presents a description of the DHT, the necessary support equipment, and details of the measurement system. Performance evaluation tests conducted on clay siltstone and a Cretaceous sandstone are presented since the results demonstrate some of the capabilities of the device and show some of its characteristics.

Jan 1, 1971

By L. R. Weisberg, E. A. Miller

Single-crystalline films of silicon of good quality were vacuum-deposited on sapphire. The improved crystallinity was achieved by the strict exclusion of oxygen from the evaporation system, including the use of a "oxygen-free" silicon source. To minimize possible contamination of the source, the silicon was sublimed from the solid at about 1390° C. using a simple electron bombardment system to heat the silicon. This resulted in deposition rates of about 5 to 7 µ per hr and film thicknesses of 4 to 20 µ. The vacuum during deposition was ordinarily about 5x 10-8 Torr, DESPITE the success achieved in the chemical vapor deposition of silicon on sapphire using Silane,1-4 vacuum deposition has not provided comparable properties. For example, Chu et a1.5 vacuum-deposited silicon on single-crystalline substrates of A12O3, Sic, ThO2, and other compounds, and, although some epi- but the use of ultrahigh vacuum (about 1 to 3 x10-9 Torr) during deposition did not significantly improve the results in the oxygen-free system. The crystalline quality of films deposited on (0001) sapphire was found to be considerably superior to (1102) sapphire surfaces. Using (0001) sapphire, single-crystalline films were deposited at temperatures as low as 780° C and as high as 1075°C, with the best crystalline quality obtained at about 1000°C. At this temperature, hole mobilities over 250 sq cm per v-sec were achieved. taxy was indicated, single-crystalline films were not produced. More recently, Salama, Tucker, and young6 evaporated silicon on single-crystalline sapphire, but only poor crystallinity was observed, and low carrier mobilities were measured. In the present experiments, good-quality single-crystalline films of silicon on sapphire have been achieved by specifically excluding oxygen from the evaporation. This included not only the use of a "clean" vacuum system but, of special importance, the use of an oxygen-free silicon source. This has also been shown to provide a dramatic improvement in silicon homoepi-taxy.7 As a result, silicon-on-sapphire films with hole mobilities over 250 sq cm per v-set were achieved, and single-crystal films were grown as low as 780°C and as

Jan 1, 1969

By W. J. Putnam, H. F. Moore

THIS paper gives a preliminary summary of results of tests on the resistance to fatigue under reversed stresses of steel subjected to cold-working and of tests to determine the effect of rest on the endurance of steel under reversed stresses. The tests of cold-worked steel were undertaken as part of an investigation by the National Research Council Committee on Fatigue Phenomena of Metals and were made by Mr. Moore; the tests to determine the effect of rest are part of an investigation now being made by Mr. Putnam. Both series of tests were made in the Materials Testing Laboratory of the University of Illinois. The preliminary results of these tests are reported now because it is believed that test data on fatigue strength should be available at the earliest possible moment; however, it should be clearly kept in mind that this paper gives preliminary results and is intended to encourage discussion rather than to give final conclusions. Before giving the data of the tests, the writers will explain the term "fatigue strength" as used in this paper and will discuss briefly the method used in interpreting the test data of repeated-stress tests. " The term fatigue strength, as applied to a material, may be defined as that maximum fiber stress that will cause fracture of the material after the repetition of any given number of cycles of stress, each cycle involving the variation of stress from a minimum to the above maximum. The fatigue strength, then, varies with the number, of repetitions occurr,ing in the lifetime of a structural or machine member and with the range of stress for each cycle of stress. The fatigue strength will be lower for a member in which the stress is completely reversed than for one in which the stress varies from zero to a maximum. In interpreting test data from fatigue tests under reversed stress, the stresses and corresponding numbers of repetitions required for failure are plotted on logarithmic cross-section paper. In 1910, Professor

Jan 1, 1920

By R. U. Jackson

Belt conveying is a method of transportation that requires proper servicing and maintenance if completely economical results are to be obtained from the system. With a trucking system, it is common practice to deliver the trucks to a servicing station each day or at the end of each shift. With railroad transportation there is a similar procedure. Sufficient credit is seldom given to this periodic inspection and maintenance procedure, yet it is the key to the successful operation of trucking and rail haulage systems. How about the belt conveyor transportation system? Here is a system that requires no operator for each individual unit. It requires only a main switch and an adequate sequence interlocking system, and the system is so simple to operate that maintenance is considered as only a casual requirement-nothing is done about it until after trouble has developed.

Jan 1, 1956

By Charles A. Anderson

Arizona and western New Mexico contain 17 of the 25 leading copper mines in the United States. Production of molybdenite, lead, zinc, and by-product gold and silver is important. Precambrian ore deposits are largely limited to the Yavapai Series in central Arizona and most of the metal production has come from massive sulfide deposits, dominantly pyritic but containing different amounts of chalcopyrite, tennantite, sphalerite, and galena. Their origin has been interpreted by some geologists as hydrothermal replacement of schist, and by others as syngenetic deposits later metamorphosed. Most of the important ore deposits are of Mesozoic and early Tertiary age, dominated by the porphyry copper deposits spatially related to stocks, plugs, sills, or dikes of quartzbearing porphyritic to granular rocks. Host rocks for these deposits include the associated intrusive rocks, Precambrian schist and granitic rocks, Paleozoic limestones, Mesozoic(?) porphyritic andesite, and Mesozoic arkose and siltstone. Chalcopyrite and pyrite are the dominant hypogene sulfide minerals in the porphyry copper deposits, accompanied by minor molybdenite. The Questa deposit in New Mexico is largely molybdenite. Supergene sulfide minerals are chalcocite and minor covellite. Some ore bodies consist largely of hypogene sulfides, some are dominantly supergene sulfides, and others are mixed hypogene-supergene sulfides. Supergene oxide-copper minerals locally are important. Intense hydrothermal alteration accompanied the metallization in all of the porphyry copper deposits; five types are recognized, ( 1) propylitic, (2) argillic, (3) potassic, ( 4) quartz-sericite (without clay), and (5) lime silicate. The origin of the closely spaced fractures that contain ore minerals in intersecting veinlets is debatable; some geologists favor tectonic forces and others suggest cooling of magma or shrinkage due to alteration. Breccia pipes, veins, and limestone replacements account for some important deposits of Mesozoic and early Tertiary age, and presumably these are genetically related to the various intrusive rocks of this age. The St. Anthony deposit of Cenozoic age in southeastern Arizona is unique, consisting of a lead-zinc vein associated with later molybdenum and vanadium oxide-minerals. Cenozoic manganese deposits in western Arizona are an important resource in the Artillery Mountains, but the extent to which they may be exploited is a metallurgical and economic problem.

Jan 1, 1968

By Robert Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 4th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 3rd edition (1960) of Industrial Minerals and Rocks will clearly demonstrate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Re- view. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 3rd edition of Industrial Minerals and Rocks. Most of these, of course, are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 11th annual meeting in 1975, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the U.S. Geological Survey and the U.S. Bureau of Mines. The two agencies publish many reports and maps on a variety of geo- logical and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications. (New Publications of the Geological Survey, U.S. Geological Survey, Washington, D.C. 20242) and New Publications-Bureau of Mines, Publications Distribution Branch, U.S. Bureau of Mines, 4800 Forbes Ave., Pittsburgh, Pa. 15213). The U.S. Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, and 1970. Three other major series of publications by the Bureau are Information Circulars, Reports of Investigations, and Mineral Trade Notes. The latter is particularly good for news of foreign developments. A new Professional Paper No. 820 of the U.S. Geological Survey, 1973, summarizes data on the mineral resources of the entire country. The USGS, in cooperation with USBM, other Federal and various state agencies, has also prepared summary reports on mineral and water resources of given areas which include

Jan 1, 1975

By H. Conrad, E. Stofel

The fracture behavior of 60-deg-oriented sapphire crystals was investigated for both tension and compression. Plastic flow on the basal plane was found to be a factor in reducing the tensile stress required to produce fracture in the temperature RECENT experiments1-' have shown that single crystals of a alumina (sapphire) can deform plastically, particularly at temperatures greater than 1000°C. The effect of this plastic flow on the fracture behavior of sapphire was not established, but range 1100º to 1500ºC. Mechanical twins, both (0001) and (0111) types, were produced by compression in the temperature range 1100" to 1300°C. Cracks propagated more readily along the twin boundaries than in the nontwinned crystal. experiments with other ceramic crystals4'5 have shown that plastic flow can initiate cracks that lead to catastrophic failure. This suggests by analogy that plastic flow might also be an important factor in the fracture of sapphire crystals. A recent experimental investigationS undertaken to determine the mechanism of plastic flow in sapphire provided an opportunity to study the type of fracture produced after various amounts of plastic shear strain. The results of this study of fracture are reported in the present paper. During the course of

Jan 1, 1963

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By Welton J. Crook

Unless present, in considerable praportion, metals of the precious-metal group—other than gold and silver—are not readily detected by the methods of fire assaying usually applied to ores and metallurgical products. Platinum, when present in small quantity, will ordinarily be reported as silver unless special methods of parting are used. Other elements occurring in the gold itself are all fluxed and slagged in the assay operation and if analyses are made on bullions the melting and slagging operations to which the bullion has been subjected may eliminate most of the associated elements. On the other hand, the analysis of precipitate from the cyanide treatment of gold ores may reveal the presence of many unexpected elements, such as tungsten and molybdenum. It is uncertain, however, whether many of the elements present in the precipitate are derived from the ore gangue or from the gold itself. No very general survey of the distribution of metallic elements in gold seems to have been made. Rose and Newman,l in connection with the composition of native gold, say in part as follows: Gold is occasionally found alloyed with copper and sometimes also with iron, bismuth, lead, mercury, tin, antimony, palladium or rhodium. Rhodium gold from Mexico was found to be of the specific gravity 15.5 to 16.8 and contained 34 to 43 per cent of rhodium. The native alloy of palladium, gold, and silver from Porpez contains 85.98 per cent of gold, 9.85 per cent palladium and 4.17 per cent silver. Mal-donitk, from Victoria, contains gold 64.5 per cent, bismuth 35.5 per cent (Louis). Dana2 says that native gold is usually alloyed with silver in varying amounts, and that sometimes it also contains traces of copper and iron. Rare varieties contain palladium, rhodium and bismuth. Other authors, for instance Zeigler3 and Clark,4 give similar information. Most references on the subject agree that ordinary native golds contain, in common, the elements silver, copper and iron. After completion of the work of which this paper is a record, the conclusion is reached that all ordinary native gold probably does contain these elements and, although in certain cases other elements may be found to be present, that it is difficult to

Jan 1, 1943

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By C. E. Wood, E. P. Barrett, T. L. Joseph

The invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.' After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it: His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be cncountered from oxidation of the iron. Mushet was not only an inventor; he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, and he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 1, 1927