Search Documents

By Barry K. McMahon

Following minor slope failures at the commencement of mining the west wall of the Kanmantoo Mine was redesigned from an overall slope between haul roads of 55° to 46°. This decision was based on a probabilistic analysis which indicated that 46° was the optimum economic slope.

Jan 1, 1983

By James Hance

INTRODUCTION SEVERAL years ago the writer was connected with the Mint and Assay Service of the Federal Government as Assistant Assayer at the-Salt Lake Assay Office. At that time cyanide bars formed approximately half of the bullion purchased by that office. Disagreement in valuation between the producer and the office was not infrequent and to a lesser extent between the Assay Office and the Mint, this latter issue being soon obviated, however, by adopting uniform methods of sampling the bars. A nice problem seemed to offer itself for research and the writer began a series of experiments which were soon terminated, however, by his going into other work, and which he regrets have not since been completed. The results attained may suggest lines of approach to this problem and are, therefore, offered in this article. Frederick P. Dewey, Assayer of the Mint Service, U. S. Treasury, has had abundant opportunity to study this phase of metallurgy, and has published several articles relative thereto.1 In the last article cited Dewey quotes analyses of cyanide bullion similar in content to that with which the writer worked, and which show some of the variations met with. In the discussion of these papers,2 comparison has been made in terms of copper bullion, but to the writer this seems of questionable value. Copper bullion may resemble silver bullion, but its similarity to, gold bullion with little or no silver content is another thing. The freezing-point diagram of Roozeboom, reproduced on page 881 of the discussion cited, is for the gold-silver series as stated. The original problem under discussion, however, is not this alloy but gold with base metals other than copper. As for the statement that the corners are the worst places or

Jan 2, 1916

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By Charles W. Goodale, William A. Akers

The treatment of silver-ores of too low a grade to justify either smelting or preliminary roasting, and yet not " free" enough to permit of raw amalgamation, has ever been a serious problem. As bearing upon it, the operations of the Combination Mining and Milling Company of Black Pine, Deer Lodge county, Montana, during the past year may not be without interest. It is not claimed that the process to be described is not susceptible of great improvement, nor is any claim of originality made for it; but its use is, as yet, not very general, and it seems to offer a means of profitably working the large class of partially-decomposed argentiferous ores which, by reason

Jan 1, 1890

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 5, 1927

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By Jose Luis de Valle Alonso

Although present electrolytic zinc manufacturing processes are aimed at the direct wet process recovery of the metal, and, with this end in view, several industrial scale patents have been applied for during the last few years, the object of this paper is to enhance the possible metallurgical interest in the conventional recovery of zinc and other metals from leaching residues. Therefore, its main end is the description and discussion of the recovery process of zinc, lead and cadmium from leaching residues. Fundamentally, the process consists of the following: Flotation processing to recover the non-roasted blende still contained in the residues. Pyrometallurgical processing of flotation tails in low-shaft furnaces (kilns) and open-flame rotating furnaces and the ensuing recovery of zinc, lead and cadmium as a mixture of their oxides through volatilization.

Jan 1, 1970

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

By D. B. Hobbs, L. W. Kempf, R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17S and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings. REVIEW OF LITERATURE The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

Jan 1, 1928

By Samuel Hoyt

THE writer has long been interested in seeking an explanation of the upper heat effect in the copper-tin alloys over the a + ß range, first described in 1913. These notes are offered, not at all as the final explanation of this heat effect, but rather to indicate certain progress which has been made toward establishing what happens over this temperature interval. While working on the thermal analysis of the copper-rich kalchoids (copper-tin-zinc alloys), it was noted that those alloys containing major portions of tin and minor portions of zinc exhibited two marked heat effects, one at about 520° C. and the other at about 600° C., instead of the single effect which is generally observed in either of the two binary series. This matter was discussed with Dr. Guertler, who suggested that a heat effect at about 600° C. in the pure copper-tin alloys might be expected. This led to a more searching examination of the thermal critical points in the pure copper-tin alloys, with the result that a marked, although somewhat weak, heat effect was located at about 600°. Somewhat later, this upper heat effect was discussed with Dr. Burgess, and it was requested that the Bureau of Standards make heating and cooling curves of one of these alloys for the purpose of removing any possible doubt as to the actual presence of the heat effect. Results obtained by the Bureau are given in Plate I. In an earlier paper1 differential curves were published showing that the heat effect occurred at constant temperature over the a + ß range and increased in magnitude with the amount of a up to a point somewhat above 20 per cent. tin. No heat effect was noticed at this temperature in the eutectoid alloy. The existence of this heat effect seems to require a modification of the present copper-tin diagram in the a + ß field, and it has been the object of the work here presented to secure the evidence upon which such a change should be based.

Jan 12, 1918

By Walter E. Hopper

The Caddo oil-field, shown in Fig. 1, is located in Caddo parish, northwestern Louisiana. The known producing territory of oil is covered by townships 19 N, 20 N, 21 N, 22 N, and ranges 15 and 16 W., shown in Fig. 2. The center of the field may be taken as Oil City, 24 miles north of Shreveport, on the Kansas City Southern railway. Shreveport is the second largest city in the State, and is the connecting point of five railroad-lines. Drilling at the present time, however, is going on all over northern Louisiana, especially in Caddo and the neighboring parishes. During the winter of 1908-09 I spent 'four months in the Caddo field, under the direction of the Louisiana Geological Survey and the U. S. Geological Survey. II. History and Development. Natural gas escaping at the surface is found at numerous places in northwestern Louisiana. At Shreveport, the plant of the Shreveport Ice & Refrigerating Co. has been lighted by natural gas for 20 years. The well was drilled for water, but was abandoned on account of the gas. A test well, put down in 1905 near the western limits of Shreveport, was driven to 1,650 ft., and encountered indications of gas and oil at various depths, but did not succeed in finding enough to be profitable. Attention was first attracted to the Caddo field in 1895 by indications in water-wells from 40 to 60 ft. deep, in which the pressure of natural gas was noticeable. This indication of gas in a shallow well led to the drilling of the first well in the Caddo field, the old Savage Brothers & Morricell, or the Caddo Lake Oil and Pipe Line No. 1. The rig for this well was erected in May, 1904, and drilling began in June, 1904. The well was bailed Mar. 23, 1905, with a small amount of oil. It was deepened July, 1905, and converted into a "gasser" Jan. 3, 1906. It was abandoned January, 1907. In consequence of the finding of oil in the Savage well, drilling-operations were pushed with energy; and in April, 1905,

Jan 1, 1912

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By John N. Dew, William L. Martin, `

This paper describes the results of a laboratory investigation conducted to obtain data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. Air and fuel requirements, rates of advance, com-bustion temperatures, and coke and fluid distributions are presented. The mechanism of oil recovery by in stiu combustion is discussed. Five crude oils ranging in gravity from 10.9 to 34.2"' API were prodrrced from a semiadiabatic, uncon-.solidnted sand pack by in situ combustion. Experimental conditions were varied over a wide range in order to determine the inter-relation-.ships of process variables. The mini-mum air flux requirement for self-sustained combustion was found to he less than 10 scf/hr-ft'l. The rate of advance of a self-sustained combustion zone was found to be nearly proportional to the air flux at the combustion front. The effects of presrure and injected air flux were studied in a series of experiments using a 21.2" API crude. A minimum air require-ment was observed at an air .flux of 20 scf/hr-ft'. The oil saturation con-sumed as fuel averaged 5.5 per cent of pore volume. The effect of air pressure was, found to be .small for experiments having high combustion eficiencies. This study should promote a better understanding of the problems and mechanisms involved in labora-tory investigations and field applications of the in situ combustion pro-cess. The data presented will be use- ful in the interpretation of results of field tests. When tempered with volu-metric sweep efficiencies, the data can be used in making preliminary economic appraisals of the process as applied to reservoirs containing high porosity unconsolidated media. INTRODUCTION The purpose of this work was to obtain laboratory data for an evaluation of the in situ combustion process as a method of producing crude oil from reservoirs. In situ combustion basically consists of (1) injecting air into a reservoir through selected input wells to create an air sweep through the reservoir, (2) igniting the crude at the injection well, and (3) propagating the combustion front through the reservoir by continued air injection. By this means, oil is swept toward producing wells in the area. The fuel for combustion is supplied by heavy residual material (coke) which has been deposited on the sand grains during distillation and cracking of the crude oil ahead of the combustion front. Recovery of petroleum by a combustion or heat wave process is not a new idea. F. A. Howard was granted a patent in 1923 on a process in which air and a combustible gas were pumped into an injection well and ignited.' Russian engineers reported on field experiments with a crude oil gasification process in 1935'. Other known early field tests include those conducted near Bar-tlesville and Ardmore, Okla., in 1942." More recently completed field tests include an inverted seven-spot by Sinclair Oil Co. in the Delaware-Childers field, Nowata County, Okla.'; a three-well and an inverted five-spot test by Magnolia Petroleum Co. in Jefferson County, Okla."."; and a test by California Research Corp. in the Irvine-Furnace field in Kentucky. The Worthington Corp. has completed a test in cooperation with the Forest Oil Corp. in Clark County, 111.l Several field tests are now in progress. Sinclair has acquired a 600-acre lease in the Humboldt-Chanute field, Allen County, Kans., and is under way with a large-scale operation. Three field tests are under way in California. The General Petroleum Corp. is conducting an inverted five-spot pattern test in the South Bel-ridge field in Kern County under a cooperative agreement with 11 other companies, including Continental Oil Co. California Research Corp. is conducting a four-well pattern test in Midway-Sunset field near Maricopa, and Richfield Oil Corp. is under way with a test in the Ojai field in Ventura County. Although the published information is valuable concerning results of field tests, little laboratory data other than that reported by Kuhn and Koch5 are available to aid in appraising the tests from a technical or economic standpoint. Engineering data needed to evaluate the process include the amount of air required per barrel of oil recovered, minimum injection rates which will support combustion, rates of advance, air required per unit volume of reservoir cleaned, amount of oil recovered, and amount of oil consumed as fuel. The present laboratory investigation was undertaken to provide these data for that portion of the reservoir swept by the combustion zone. The first phase of this investigation was exploratory in nature and was conducted at injection pressures less than 100 psig. Data were ob-

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By Alan Morris

Brass rod for use in automatic screw machines is one of the major products of the brass mills. A large tonnage is consumed each year in the manufacture of an endless variety of finished articles and parts for assembly into other products. The machines that do this work have been developed to a high degree of efficiency, and their manufacturers are still striving for higher production speeds. This development has brought with it a demand for brass rod to meet the increasingly difficult machining conditions. This paper is a report of the results of tests undertaken in an effort to obtain a measure of the effects of such variables as lead content, microstructure and cold work on the machinability of brass rod. It is realized that the term "machinability" has never been well defined. Power, finish and tool life all should have a place in such a definition. In practice it is sometimes found necessary to sacrifice some of these in order to obtain a rod that will not tend to throw up a burr, or will give a burr which is easily tumbled off. Again a specially stiff rod may be necessary because of long overhang from the chuck or a rod of special characteristics is needed to take a given broaching operation without chattering. It is only through an understanding of the effect of basic mill operations on the machinability of the rod that such problems as these may be solved most economically. It is hoped that this paper, together with the discussion it may evoke, will prove to be a basis for such an understanding. Testing Apparatus The testing apparatus used was of the single-tooth milling cutter type, in all respects sirnilar to that first used and described by Airey and Oxford1 and again by Boston. The machine used in the present test is shown in Fig. 1. It is an ordinary milling machine in which a heavy pendulum has been substituted for the pulley on the arbor. If the pendulum is raised

Jan 1, 1932

By Donald A. Dahlstrom

In 1961 it became increasingly more evident that significant technological changes must be made in minerals beneficiation. The status quo in technology in today's competitive markets will not be tolerated. Higher productivity, greater recoveries and newer and better products must be sought and incorporated with lower operating costs. In other words, "when you build a new mill, don't build an old mill." Recommended reading for proof of the vital necessity of new methods and techniques is in the September 1961 issue of MINING ENGINEERING. The article by one of MBD's cherished and true veterans, E. H. Rose, is entitled "Iron Ore: The BIG Picture". Because of new beneficiation methods for iron ores, nearly 47 million tons of plus 60% iron concentrates will be produced and another 40.1 million tons of capacity will be under construction or committed. Thus in a relatively short period, 87 million tons of this high-grade iron concentrate with record low silica will be available. As Mr. Rose also points out, "in gross tons, without allowance for better grade, this is the equivalent of almost exactly two-thirds of all iron ore used for all purposes in the U.S. and Canada in the peak years of 1953 or 1957." Needless to say, improved mineral beneficiation methods have had far more reaching effects than just the production of higher grade iron concentrate.

Jan 2, 1962