Search Documents

By R. M. Kuralt

CONCESSION from the Chilean government granting the company use of the Rio Salado water stipulates that a minimum of 35,000 metric tons of such salty water must be diverted from the Salado daily, and be disposed of in a manner not to contaminate the Rio Loa to the east of its confluence with the Rio San Salvador at Chacance, Fig. 1. Consequently, the selection of a suitable site for the sulphide plant tailing disposal had the additional problem of the disposal of excess brackish waters. Studies of the terrain in the area directly to the south of the plant indicated that construction of tailing ponds would be costly, and generally unsatisfactory due to excessive slope of the ground, lack of flanking hills, danger of raising the groundwater level thus causing springs along the Antofagasta-Bolivia railroad; and the possibility of creating a dust nuisance at the plant site or at Calama due to blowing sands. Further to the southwest the San Salvador river canyon offered some possibilities and surveys were made at sites A to D, inclusive, Fig. 1. Here again costly dams would have been necessary to impound the tremendous quantity of tailing produced by the new plant, and provision would have to be made to handle a considerable flow of water through the disposal area to the west of the Rio Opache. Additional surveys were made in the area to the southeast of the plant which brought to light the existence of a natural basin of about 14 1/2 square miles, flanked by low-lying hills, and requiring only the most rudimentary dams to close the outlets at the western end. It has been estimated that the Salar de Talabre, as this basin is called, has the ultimate storage capacity of 1 billion tons of tailing with dam heights of only 60 ft. Pipe Line Layout After the decision had been reached to use the Salar de Talabre for the main disposal area various methods were considered for transporting the tailing from the 300 ft diam thickeners to the disposal site, 17.7 miles away. The first plan was to construct a. concrete launder on a 11 pct grade but a survey of this grade line indicated it would not lead directly into the Salar but would terminate somewhat to the north, and from that point on the slope would be considerably less than 1 pct along a natural watercourse. A slope of 2 pct or even 2 ¼ pct in such a rough watercourse or ditch is the ideal, judging from the success of operations at Cananea. Since a simple ditch is the most economical vehicle for the transportation of tailing, it was decided to use one with a 2 ¼ pct grade for as much of the distance as was possible with the existing terrain and to construct a concrete headbox, or forebay, at the terminus of the ditch to supply a steel pipe line leading the rest of the way into the Salar. Referring to the maps of the Chuquicamata area outlining the tailing disposal system, Figs. 1 and 2, one can trace the flow of the tailing from the thickeners to the Salar as follows: The 8-in. spigot pipes from the thickeners (1) discharge into a concrete sump feeding a concrete launder with a 2 pct slope. The launder carries the tailing into a concrete junction box (2) located south of the sulphide plant. The purpose of the junction box is to provide emergency facilities for diverting the tailing flow from the main disposal area to the emergency area. It also provides a junction point for the launder from the sulphide plant's future east extension. The box is fitted with a pair of radial gates controlling flow into the main tailing ditch (6) or the emergency ditch (3) which terminates on the pampa. All ditches are of the same cross section, namely 4 ft wide at the bottom with 1 : 1 side slopes and with a minimum depth of 21/2 ft. Where the nature of the ground demands it, the ditches are lined with stone rubble. The overflow from the plant's 10 million gal reservoir (4) is led into the main tailing ditch by way of a spillway ditch (5). The main ditch terminates in a trashscreen fitted, concrete forebay (7) which serves as a headbox for a 24 in. O.D. x 3/8 in. wall, Dresser coupled, steel pipe (10) and a 12 in. x 8-gage spiral welded, wedge-lock coupled, steel pipe (8). The forebay is fitted with two compartments, one for each pipe, and flow into each is controlled by radial gates. Each compartment is fitted with a 6-in. drain pipe controlled by a rubber pinch valve. To protect the forebay from the abrasive effects of the tailing, the sides of the compartments will be lined with old

Jan 1, 1952

By T. Tholana

South Africa hosts some of the world?s largest known resources and reserves of minerals that are strategically important to the global economy. The country?s mining industry contributes significantly to the national economy in terms of gross domestic product, export earnings, corporate tax receipts, remuneration earnings, and employment. Platinum, gold, and coal are significant minerals because they make the largest individual contributions to these economic indicators. Several factors impact the cash cost performance of operations that mine these minerals, thus affecting the future sustainability of these operations, which are generally ?price-takers?. It is therefore important that the cash cost performance of operations for these key minerals is analysed. Commercially available industry cost curves can be used for such analysis. However, some companies may not be able to afford to purchase these curves. This paper presents a simple Microsoft Excel® algorithm for constructing the curves. It also demonstrates how the constructed industry curves were used to analyse the cash cost performance of South African mining operations for the three selected minerals for the period 2007 to 2011, which included the 2008 global financial crisis. The analysis revealed that the operations were affected by several global and local factors during the review period. The work reported in this paper is part of an MSc research study at the University of the Witwatersrand. Keywords cost curve algorithm, economies of scale, cash cost performance

Jun 1, 2013

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By L. Yuan

In the U.S. coal mining industry, most spontaneous combustion fires occur in longwall or worked-out gob areas. In order to reduce the fire hazard caused by spontaneous combustion, it is important to understand how ventilation and gob characteristics affect the spontaneous heating process. Given the difficulty to conduct field tests in such an environment, a computational fluid dynamics (CFD) study was conducted to investigate the effects of ventilation and gob characteristics on the spontaneous heating process in longwall gob areas. Two longwall panels with a bleeder ventilation system were simulated. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using the Arrhenius rate law and kinetic data obtained from previous laboratory-scale studies. The heat generated from the spontaneous heating is transported by convection and conduction, and oxygen and the oxidation products are transported by convection and diffusion. Unsteady state simulations were conducted with different ventilation conditions and gob permeability distributions. The ventilation parameters varied in the simulations are the pressure at the bottom of the bleeder shaft and regulator resistance in the second entry inby the longwall face.

Jan 1, 2009

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By Higgins RJ

Environmental investigations have been undertaken by Ok Tedi Mining Limited (OTML) since 1981 when the Ok Tedi Environmental Study was commenced. Environmental monit- oring and management programmes were implemented in 1983. The programmes included water quality monitoring, river flow and sediment monitoring, surveillance of aquatic biological communities and a health and nutrition survey of the local people. These original programmes have continued, and additional programmes of work have been developed and revised to reflect changing operations and the need to focus investigations on specific areas and issues of concern. In April 1990, following the establishment by the Government of Papua New Guinea (PNG) of environmental management criteria for the Fly River system, compliance monitoring programs were introduced. Details of the compliance and additional monitoring programmes undertaken by OTML throughout the Ok Tedi and Fly catchments, including programmes of investigation in the Fly River estuary, Gulf of Papua and Torres Strait, are presented.

Jan 1, 1991

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

By Hellsten KJ, Butt CRM

Major Francis Hamilton Buchanan coined the term `laterite' (Latin; brick-rock) in 1807 for the red earths used for building blocks in southern India. Although these earths were actually weathered basalts, the term is now applied to weathering profiles developed upon a wide range of bedrocks. The Ni-laterites are a special class within the broad laterite family.

Jan 1, 1996

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

By David Sprott, Patrick Andrieux

In 1990 the Noranda Technology Centre commenced a project to develop an interactive three-dimensional blast design system using a commercial computer-aided drafting and design package (CADD). The objective was to alleviate the blast engineer from the tedious and time consuming blast layout and design functions normally done by hand. This would allow more time for optimizing blast designs through assessing multiple options. Since several blast design software "tools" already existed at Noranda, the need arose to integrate all the applications into one overall system that shared one common database. The result is BLASTCAD.

Jan 1, 1991

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

In line with DML Resources continual forward management policies, the Roscommon Quarry operation has recently installed and commissioned a Nordberg 7 ft Symons cone crusher and a HP 300 cone crusher. Both machines have enhanced the production capabilities and quality control of the Roscommon comminuition circuit and they will provide efficient and reliable crushing well into the next century.

Jan 1, 1994

By Yufeng Guo

Mineralogy and physico-chemical characteristics of a nickel hydrometallurgical residue and recovery of iron-bearing minerals by flocculation-magnetic separation were studied. The results show that the nickel residue is super-fine and fraction less than 0.045mm reaches 85.4%. Ferrous minerals are chiefly magnetite and ferruginous glass. Magnetite accounts for 31.7% and exists as free magnetite. Ferruginous glass is of multicomponent amorphous substances with low-iron grade but strong magnetism, and accounts for 39.9% of total iron minerals. Addition of flocculants increases granularity and magnetic force of fine iron-bearing particles and improves iron grade and recovery. The tests with flocculation separation show that a concentrate assaying 56.68% Fe with 81.72% recovery was obtained in a magnetic tube. A concentrate with 56.92% iron grade and 67.96% recovery was obtained by flocculation-magnetic separation with a magnetic cylinder.

Jan 1, 2006

By Dan L'Heureux, Joe Haid, Stephen H. Chung

Most coal deposits in Western Canada involve steeply dipping multiple seams. An efficient way to recover coal seams would be to drill through the seams and blast both the overlying and underlying waste material in one shot without disrupting the coal seams while fragmenting the waste rock for easy removal. This requires special blasting techniques as reported by Chung and Jorgenson in 1985.

Jan 1, 1998

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By D. Richardson

Presentation Objectives ?Demonstrate the utility of 3D modelling for visualizing exploration data ?Demonstrate the target generation ability of 3D model query methods Exploration Criteria -Example Given the Geology of Sudbury What Are Our Exploration Criteria? (selected examples) ?Geometry ?Trends ?Lithology ?Proximity to Sulphides ?Length and Grade of Anomalous Mineralization ?Distance from Footwall In Addition ?Geophysical Criteria ?Economic Criteria ?Amount of Available Space ? Depth

May 1, 2006

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004