Search Documents

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Hamid Maleki

Roof falls are one of the leading ground control problems that adversely influence productivity and worker safety in underground mines, construction sites, and nuclear waste repositories. To control roof stability problems, the operator needs to have practical methods for measuring changes in strata conditions and criteria for defining the timing of secondary support installation. The objective of this study was to develop measurement techniques and criteria for assessing roof conditions at the mining face. An integrated rock deformation and tomographic imaging method was developed and applied at two sites in a western U.S. trona mine. It was shown that rock damage occurred at a deformation of 30 to 60 mm (1.2 to 2.4 in) (2 to 4 pct strain) and was associated with a significant (16 pct) reduction in wave velocity. Thus, supplementary support may be installed when there is a measured change in wave velocity of at least 16 pct. Tomographic measurements can be obtained in rocks rapidly, thus providing a powerful tool for analyzing growth of failure and for installing supplementary support systems in a timely manner.

Jan 1, 1996

By Jun Lu, Mark Van Dyke, Daniel W. H. Su, Greg Hasenfus

"This paper presents the geologic and ground control challenges that were encountered by CONSOL Energy’s mining operations in southwestern Pennsylvania. A sandstone-to-limestone geology transition was encountered by Mine A, where the primary 8-foot bolts were anchored in claystone. Upon experiencing roof sags and a roof fall in the return entry, 6-foot high-tension, fully-grouted primary bolts were employed along with 16-foot center cable bolts at every other strap to improve beam building and to ensure proper anchorage into the competent limestone. No longwall delay was reported within this geologic transition zone, although there was some difficulty in maintaining an open #2 entry airway behind the longwall face.The geologic encounter in Mine B was more complex, where fluvial deposits of massive sandstone channels, shale channels and pyritic-rich, green claystones were encountered on both sides of the mains, and which impacted both development and longwall ground control. In particular, poor transitional roof areas near the edges of the sandstone and shale channels often posed significant ground control challenges. In addition, hydraulic fracturing was sometimes utilized to enhance caving of massive sandstone behind the shields to relieve pressure at the face. Longwall face conditions and advance rates were documented to illustrate the effects of sandstone channels, shale channels, and green claystones on safety and productivity and to demonstrate the effectiveness of the hydraulic fracturing.Shale channels, slickensided zones, laminated roof zones, soft floor, and a regional syncline were encountered in Mine C, the combination of which posed unique ground control challenges during both development and longwall mining. The presence of soft floor, coupled with the presence of thick floor coal and deep cover, resulted in headgate convergence during retreat of the first right-hand longwall panel. Two-piece 8-foot bolts were sometimes observed to fail at the coupler within the laminated roof zone, and 6-foot, 1-piece, fully-grouted point-anchor bolts were employed as the primary bolts thereafter."

Jan 1, 2015

By Roy E. Peterson

The Bureau of Mines conducted bench-scale research to evaluate materials which showed potential as low-cost reductants for use in the ironmaking industry. These materials were lignite, subbituminous coal, coal char, tree trimmings, refuse--derived paperboard, used crankcase oil, and peat. To compare their effectiveness, the materials were tested in the reduction roasting of nonmagnetic taconite and, except for oil and peat, in the reduction of iron oxide pellets to metallized pellets. Reduction was conducted in a 18-cm-diameter, rotary drum, which was externally heated in an electric furnace. Over 92 pct of the iron was magnetically recovered from a nonmagnetic taconite after roasting with any of the reductants, but greater quantities of reductant were required to achieve this when the waste materials were used. The fossil fuels were also more effective for metallizing pellets, although metallizations above 90 pct were also obtained with tree trimmings and refuse paperboard. However, refuse paperboard had to be frequently recharged to the furnace because it depleted rapidly.

Jan 1, 1983

Longwall mining originated in the early 18th century in the county of Shropshire in England, where it was known as the longway method. Its name implies the extraction of the seam over a long continuous length or wall of exposed coal. Until the late 19608 and early 1970s the use of the longwall system with a few exceptions was confined to the United Kingdom and Europe. It was not until the early 19708 that the highly productive longwall faces we now know, were developed and the application of the longwall system extended to Australia, South Africa, United states of America and other parts of the world. The modern longwall face has three major components, namely: +         the machine to break and load the coal +         the face conveyor; +         and a system of roof support.   This paper reviews the development of longwall mining technology. The parameters directly influencing the production 'of a modern longwall face are considered, as are the possible constraints to the further development of the longwall system.

Jan 1, 1991

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By M. W. Franklin, D. W. Hendriks

"Changing ore types, feed grades and c1rculat1ng loads are some of the many factors that can make flotation feed-back control difficult. To control a flotation circuit using conventional fixed-parameter control algorithms, one must either tune the controllers very often or tune the controllers to the middle of the normal operating range. The former approach is very time consuming, while the latter approach can lead to long periods of either very sluggish responses or highly reactive responses which can lead to instability. The problem becomes compounded if feed-forward variables are introduced, creating even more variables to tune. An alternative to a fixed-parameter control algorithm is an adaptive control algorithm. An adaptive control algorithm continuously retunes itself based on previous reactions to its changes. Feed-forward control also becomes much more viable because the algorithm will tune the feed-forward parameters and the feed-back parameters simultaneously. Using the combination of feed-forward and feed-back tuning is an effective way to decouple the loops needed in flotation circuits where one circuit feeds into another. The advantages of adaptive controllers over conventional controllers will be introduced through the use of a simulator. Also discussed will the be the implementation of adaptive controllers at Brunswick Mining and some of the modifications that are available to help solve more difficult control problems.Brunswick Mining is located just outside of Bathurst, New Brunswick. The concentrator processes approximately 10250 tonnes per day of ore that assays at approximately 8.9 %zn, 3.6 %Pb, 0.3 r.cu and I 00 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 34 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb."

Jan 1, 1986

By J. C. Duchon

The U.S. Bureau of Mines is conducting human factors research for the purpose of reducing accidents and improving the person-machine interface found in surface and underground mining operations. Miners are exposed to a variety of environmental stressors, e.g., extreme heat, noise, vibration, and adverse illumination, throughout the workday. Exposure to these environmental stressors has been noted in the literature to affect performance on vigilance tasks. Since impaired performance at vigilance tasks can lead to industrial accidents, further investigation of the effects of environmental stressors on human performance is warranted. A brief description of the environmental conditions present in the mining workplace is followed by a review of experiments dealing with the effects of environmental stressors on vigilance task performance. The applicability of past research to actual mining operations is considered.

Jan 1, 1989

A subsurface study of the Maria Lode and associated hydrothermal alteration of andesites within the Karangahake epithermal gold-silver deposit defined the local evolutionary sequence in the once active geothermal system.   Some implications for mining of epithermal deposits arise as a result.

Jan 1, 1984

By T. Ertekin, X. Dong

This paper identifies the need for the development of specialized inverse solution techniques for the analysis of pressure transient data for the characterization of the transport and sorption properties of coal seams. Central to the proposed inverse solution technique is a specially structured artificial neural network (ANN). The most important transport and sorption characteristics of coal seams are butt and face cleat permeabilities, macropore porosity, Langmuir volume constant, Langmuir pressure constant, and sorption time constant. Conventional methods, such as type curve matching techniques and laboratory-derived measurements are handicapped in terms of being representative over the entire domain of interest. In this paper, we utilize analytical forward solution techniques for various combinations of characteristics of coal seams to generate training and testing patterns. These training patterns are shown to an ANN structured to learn the ubiquitous non-linear relationships that exist between coal seam properties, input conditions and the pressure transients measured. The trained networks are then extensively tested to ensure that they have effectively learned the training patterns. In the final stage of the development, the networks are run in the prediction mode. The responses of the networks are found to be in agreement with the input data. The developed networks are able to generate results generally within 5% error margin for permeability and porosity and 20% error margin for the sorption characteristics of coal seams. A number of examples highlighting the capabilities and degree of effectiveness of the network in characterizing the coal seams areincluded. Keywords: artificial neural networks (ANNs); coal seam characteristics; pressure transient analysis

Jan 1, 2003

Jan 1, 1968

Automation in underground mining enhances safety and leads to economic efficiency. In the past many efforts have been made on the automation of longwall shearer operation. With respect to the ultimate goal of automation, ie self controlled operation, coal bed boundary detection is one of the key problems. For longwall human labor is necessary in order to detect the exact position of the coal seam to be excavated. The authors present a sensor concept based on infrared technology and pattern recognition which will solve this problem. The very harsh underground conditions set high demands on the implemented sensors. The combination of infrared sensors and powerful processing algorithms is part of the innovative concept for automation of the new Eickhoff Bergbautechnik GmbH SL 750 shearer loader. The multi-sensor automation system EiControlPlus which is designed for the complete detection of the machine environment fills in the gap in the coal-excavation automation by building a recognition system that turns the shearer loader into an 'intelligent machine' which is capable of detecting the correct position of the seam to be excavated and thus enables human-free coal mining.

Dec 6, 2010

By Robert G. Nisle

The classic theory of pressure build-up in shut-in oil wells as developed by Horner and van Everdingen is based on two-dimensional radial symmetry in the well-reservoir system. Such symmetry does not exist in the case of a well which parfiially penetrates the producing formation. As a result of this lack of symmetry the use of the classic theory in such cases become questionable. In this paper the mathematical theory has been extended to include the case of partially penetrating wells. Numerical solutions illustrating the up-dication of the equations are presented. The effect of partial penetration on pressure build-up is shown by a comparison of synthetic pressure build-up curves derived from the numerical solution of the equation for partially penetrating wells for various degrees of penetration. It is shown that partial penetration is detectable from the characteristic shape of the pressure build-up curve and that formation productivity may be calculated from the pressure buildup data in a manner identical to that described by the classic theory. INTRO DUCTION The use of pressure build-up data on shut-in oil wells is a well-established technique for the measurement of reservoir productivity. The work of Homer' and van Everdingen' is well known. Since the publication of their pioneering work, others"' have elaborated and extended the technique. These authors have dealt exclusively with the case of wells that completely penetrate he producing formation. Two-dimensional radial symmetry is achieved, thereby, and the problem is greatly simplified. This ideal situation is seldom encountered in practice. But, in spite of this, the technique is often employed anyway. The question, therefore, arises: how much confidence can be placed in the results of such calculations when the data are taken on wells that only partially penetrate the producing formation? It is the purpose of this work to answer this question. Only the single-phase fluid case will be considered. van Everdigen' has presented a rigorous solution of the two-dimensional case, but because of mathematical complexity, this solution has not proved to be particularly useful. Horner' utilized Kelvin's point source solution in two dimensions and showed that it is a sufficiently good approximation for oil reservoir studies. The geometry of the well and the producing formation is illustrated in Fig. l. Geometrically the formation may be described as an infinite slab. The infinite slab is defined as the solid (the porous medium in this case) bounded by two parallel planes. Thus, the slab extends to very great distances in both the positive and negative directions of two of the coordinate axes, but is finite in

By D. K. Chibwe, P. Taskinen

"This investigation consists of a numerical and physical modelling exercise on flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a 0.2-scale cold model of an industrial Peirce-Smith converter (PSC). Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The 2D and 3D numerical simulations were carried out using volume of fluid (VOF) and realizable k-e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions. Measurement of mass transfer indicated that fluid flow in the PSC is stratified. Blowing configurations and slag volume both had significant effects on mixing propagation, wave formation, and splashing.As a potential process alternative to increase conversion efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined as well as lateral blowing conditions, and the results of the combined concept are encouraging."

Jan 1, 2015

Electrochemistry Measurement, Using Chena Analyser, to Investigate Selective Separation of Pentlandite and Pyrrhotite

Sep 13, 2010

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By Donna L. Anderson

The first section of this U.S. Bureau of Mines report includes a discussion of the navigational tasks performed by operators of mobile mining equipment, with the focus on the navigational information and guidance techniques required by continuous mining machine operators. Some previous research and attempts in remote and autonomous navigation of continuous mining machines are mentioned. Issues of research in autonomous navigation of various other mobile robots are presented, with attention focused on their applicability to a continuous mining machine navigating in the mining environment. Conclusions are stated on methods of automating the navigational tasks of a continuous mining machine, and a decision to concentrate initial attempts on the tasks of autonomous face navigation is defended. The second section of this report includes a presentation of the Bureau's proposed solution for autonomous face navigation of a continuous mining machine, which includes the employment of a mobile roof support as a reference for guidance in the face area, and a navigational guidance system for the continuous mining machine.

Jan 1, 1989

Between February and August of 1986, Dr Alfred Petrick visited New Zealand sponsored under a Fulbright grant administered by the New Zealand-United States Educational Foundation. The grant supported a research project completed by Dr Petrick having as an objective, the preparation of a preliminary economic evaluation of the mining of six Otago lignite deposits as a source of energy for steam power generation or in liquid fuels. The research is limited to consideration of preliminary geological and engineering data on the six deposits and to the time constraints of the Fulbright visit. This paper is a summary of the final Fulbright report. The complete report including the listings of the computer programs is available from the Otago School of Mines.

Jan 1, 1986

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965