Search Documents

By Eric E. Cather

Approximately 270,000 cu yd (20[0],000 cu m) of inferred subeconomic auriferous gravel resources were estimated in three Tertiary deposits in the Polk Springs study area (fig. 1 and table 1). These resources are exposed between tuff-breccia and lava flows of the Pliocene Tuscan Formation and Paleozoic or Mesozoic metamorphic rocks which suggests that although no deposits were identified in the other RARE II areas, they may be concealed beneath the Tuscan Formation. Difficulty in choosing drilling targets will make the likelihood of resource discoveries small. The development and production of these deposits would also be prohibitive under current economic conditions due to the thick covering of volcanic rocks. Recent stream gravels of Deer Creek in the Polk Springs study area contain enough gold to attract gold hobbyists; however, the stream gravels do not have sufficient volume to be considered a resource. Potential exists for additional auriferous gravels near the Occidental Mine in the Polk Springs RARE II area.

Jan 1, 1983

By Harold A. Watson

A method for measuring leakage of vapors into a chemical-cartridge half-mask facepiece during simulated use is described. The respirator, fitted with high efficiency cartridges, is worn in a dichlorodifluoromethane (CC12F2)--air test mixture while a series of timed activities (facial movements, varied breathing, exercise, etc.) is performed. Complementing other tightness tests, this method is useful particularly for studying face fit and the effect of facial movements on leakage. The concentration of CC12F2 within the facepiece is monitored continuously to observe the immediate effect of physical activity on leakage. A composite sample is collected simultaneously in a plastic bag as a measure of average leakage during the 18-minute test period. Leakage, reported as percent, is calculated from the concentrations of CC12F2 within the facepiece and in the test atmosphere.

Jan 1, 1970

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By María Julia Ubillús Mellet

El presente texto complementa el estudio de las estrategias de seguridad en las empresas mineras a través de la alienación de las herramientas de gestión humana en una cultura de seguridad y prevención competitiva, de forma que se mejore el estilo de gestión en seguridad de los equipos gerenciales en las empresas mineras, y se desarrolle un manejo adecuado y responsable entre el área gestión humana y cultura organizacional. En ese sentido, la excelencia de gestión en seguridad radica en que el elemento humano se conecte de forma sistemática a las estrategías que la organización plantee.

Sep 12, 2005

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By Matthew Janes

Statnamic load testing is becoming widely accepted as a method to quickly and economically determine the load-deflection behaviour and ultimate static resistance of high capacity deep foundations. Strain instrumented large diameter bored shafts were tested at four locations for the federal and state Departments of Transportation in the United States. Tests were conducted vertically (to 30 MN) and laterally on the shafts and, in some cases, testing was completed over water. Instrumented shaft test results provided shaft load distribution with depth and shaft shear transfer stress throughout the soil stratum. Shaft end bearing and ultimate end bearing stress values were provided. On two projects, Osterberg load cells provided comparative static data for skin friction and end bearing. Correlations between Statnamic derived static load-displacement results and Osterberg load-deflection results are very good. Statnamic lateral load test results were correlated with static lateral results in addition to providing useful dynamic response and damping data.

Jan 1, 1996

By D. K. Denton, J. M. Girard, D. F. Scott, T. J. Williams

Personnel from the Spokane Research Laboratory, National Institute for Occupational Safety and Health, examined an underground pillar at the Homestake Mine, Lead, SD. Investigations involved strain relief and seismic tomography studies in the mine, and ultrasonic velocity measurements on pillar core in the laboratory. Measured octahedral normal stress was 37 MPa (5,366 psi); seismic P-wave velocities averaged 5.2 km/s (17,060 ft/s); and ultrasonic velocities at a pressure of 39.6 MPa (5,750 psi) averaged 6.3 km/s (20,669 ft/s). The difference between in-mine and laboratory velocities is attributed to the attenuation of seismic energy by mine fractures larger and more numerous than those in the samples of core measured in the laboratory. Using these results, researchers hypothesize that pillar rocks have the ability to withstand stress an order of magnitude greater than they currently sustain.

By Richard J. Hartman

This presentation identifies some of the more common problems associated with cofferdam construction. After the various problems are identified, they are briefly explained and possible solutions and preventive measures are noted. Photographic slides used during the seminar illustrate the conditions. This discussion is limited to cofferdams which are braced structures excavated inside to allow access for construction. The common procedure is to drive sheet piling and then alternatively install bracing and excavate. They can be located either on land or in water. Loads are applied by soil, water, surcharge pres-sure, eccentricities, and impact loads. The loads are resisted by the sheet piling, the bracing, and the soil below the bottom of the excavation; each of these three components must be capable of resisting the applied loads.

Jan 1, 1987

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

By S Lal, S Rost, Q Williams, K Collerson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Shoshonite suite (absarokite-shoshonite-banakite) and adakite-hosted epithermal Au deposits are a feature of circum-Pacific magmatism. Fijian examples include Tavua (Emperor) and Tuvatu on Viti Levu. New discoveries of shoshonite suite and adakite-hosted epithermal Au mineralisation have been made in the southern Yasawa Islands and in central-northern and central-western Viti Levu. The Fijian shoshonites define four NE–SW trending suites. The oldest is the northern 7.9–5.0 Ma Yasawa suite, followed by the 4.7–3.5 Ma Sabeto–Tavua–Rakiraki suite in northern Viti Levu, the 4.7–4.2 Ma Yanuca–Vatulele suite approximately 20 km south of Viti Levu and the 3.4 Ma Astrolabe suite approximately 75 km further south. Shoshonite suite lithologies with 3.8–3.0 Ma ages also occur in the Lomaiviti islands between Vatu-Cake and Moala, to the east of Viti Levu, defining a trend oblique to the NE–SW shoshonite belts. Seatura, a 3.3–2.8 Ma ocean island basalt (OIB) volcano, sits at the northern end of the Lomaiviti trend shoshonites. Trace element/isotopic chemistries indicate that shoshonite arc magma genesis involved the melting of a hydrated supra-subduction zone mantle wedge and also a lower mantle-derived plume (OIB) component. The upwelling plume provided heat for melting and possibly Au enrichment. Accessing the melt generation zone associated with the plume required a slab conduit or window. Such slab windows form by tearing during subduction or occur at slab edges. Adakites form by plume-induced slab melting. The four NE–SW Fijian shoshonite suites are interpreted to occur in back-arc extensional zones above a slab window (tear) that migrated southward during rollback of the New Hebrides–Vanuatu subduction zone. The plume (Seatura OIB) that is interpreted to have caused mantle wedge melting and formation of the Lomaviti trend shoshonites was focused along the interface between the north-dipping Vanuatu–New Hebrides subduction zone and the west-dipping Tonga subduction zone, which we have seismically imaged at approximately 400 km depth. Our model ‘cracks the metallogenetic code’ for shoshonites and adakites and has regional and global implications for Au exploration.CITATION:Collerson, K, Lal, S, Williams, Q and Rost, S, 2015. Cracking the metallogenetic code for Fijian epithermal gold mineralisation , in Proceedings PACRIM 2015 Congress, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S. P. Lewis, R. L. Sundeen

Most of us are aware of the ever increasing use of underground space. At the Advisory Conference on tunneling in Washington, D. C. in June of 1970, the demand for construction oriented tunneling during the 1970s was estimated at some 21,000 Km of length with an excavation volume of 675 million cubic meters. Of this total, 11 million cubic meters were forecast for underground parking. Though this is a small portion of the total, it is significant to note it represents a 280% increase over the previous decade. Other areas of unusual increase were railroad tunnels, 150%, and rapid transit tunnels, 160% (1). Faced with this increasing demand, the need for improved excavating efficiency is obvious. Great strides have been made. In Japan, for example, several new long tunnels have been driven parallel to old existing ones at costs as much as 50; under those of the original tunnels (1). This is an impressive achievement. I am certain, however, that we would all agree that even greater improvement is required. Great emphasis is being placed upon sophisticated systems which include among others, mechanical borers, thermal fracturing, and various methods of rock weakening and softening. However, in hard rock excavation the fact remains that the drill-blast method continues to be the most widely used system. Undoubtedly it will continue to be one of the most important techniques in the forseeable future.

Jan 1, 1974

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

By Harry L. Siebert

Pre-splitting was substituted for line drilling to achieve stable rock slopes and reduce excavation beyond the pay line on a Connecticut highway project in 1962-63. Changes have occurred in developing rock slopes that were not foreseen by Alan Bauer and Jim Scott who in the early days understood the relationship of explosive energy to stable slopes. Cushion blasting as currently used produces slopes designed to blend or complement the natural landscape with slope holes detonated after the main body of holes. Pre-splitting is the opposite. The best results have been achieved by detonating the pre-split line of the holes first to allow readjustment of the slope plane fracture and a separate blast for the main body of loaded holes.

Jan 1, 1998

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

By Jerry J. Ran

In open stope mining borehole deviation is one of the main factors affecting the blasting results. Though previous research has identified some actual deviation patterns, these studies are unable to relate the hole deviation pattern with the blasting results and therefore it is not possible to modify the design or take remedial measures based on the prediction of the blasting results. An alternative to the conventional method for borehole surveying is the in-hole probing techniques. With their inherent errors, it is important to evaluate these surveying systems under conditions of different mine sites. The lack of available assessment methods has limited the application of these techniques. In this paper some of the characteristics of the actual hole deviation pattern are discussed based on data from surveying production holes in six stopes. A method of predicting the blasting results is proposed by considering the borehole deviation pattern. Based on the prediction stope design can be modified or further surveying is carried out to improve the blasting results. The tolerable error is introduced to relate the surveying error with the drilling pattern and therefore it is possible to assess various in-hole-surveying techniques.

May 1, 2002

By Patrick D. McLaughlin

Crater blasting techniques have had relatively little application in the surface mining industry. This is not surprising, considering the geometry required to efficiently use cratering. The more widely known blasting operations that employ some form of cratering are listed below.

Jan 1, 1992

By Robert Harris, David Duncan

The Samira Hill gold mine represents the first commercial gold project for the landlocked country of Niger in West Africa. It began production in October 2004 as the result of over 10 years of exploration and development work. There were several administrative, social and technical challenges that had to be overcome to realize the successful development of the project. The Samira mine is located on the geological structure known as the ‘Samira Horizon’ which is developing as a promising district for additional discoveries and other mine developments.

Jan 1, 2005

By Pengfu Tan

Lead blast-furnace bullion cools to near its freezing point in an operation known as copper drossing or hot drossing usually contains 0.02-0.06% copper. The removal of this copper is usually carried out in a batch operation known as sulfur drossing. Sulfur is stirred into the bullion at temperatures near its freezing point, and the dross of copper and lead sulfides that floats to the surface is skimmed off manually. A thermodynamic model has been developed to simulate the copper drossing. The phase diagram of Pb-Cu-S system has been calculated, and the effects of the process parameters, such as temperature, copper content, and sulfur content, on the drossing process have been simulated and discussed.

Jan 1, 2006