Search Documents

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

By Charlie Brumbaugh

Antarctica with its diverse conditions such as severe cold, high winds, rock and ice structure and limited explosives available posed many obstacles. This paper will give an overall view of the methods used to overcome these obstacles on a daily basis on the highest, driest, coldest continent on earth.

Jan 1, 2000

By Jean R. Garcia, Paulo J. R. Albuquerque, Renato P. Cunha, Osvaldo Freitas Neto

"Abstract Results obtained from in-situ load tests carried out on drilled displacement piles sunk in a porous, lateritic and unsaturated soil deposit, are analyzed in this paper. Three slow-maintained load tests were performed on deep instrumented piles with a diameter of 0.37 m and around 12 m long. The soil deposit consists of a superficial, silty clay “porous” layer 6 m thick, with an average standard penetration blow count (NSPT) of 4 and cone tip resistance and sleeve friction (qc and fs) of 1.5 MPa and 48 kPa, respectively. Under this layer there is a residual stratum 10 m thick, geotechnically consisting of a “porous” clayey silt with an average NSPT of 7 and qc and fs of 2.4 MPa and 202 kPa, respectively. The water table was reached at a depth of 17 m below ground level. The results of the field load tests yielded a maximum pile load (average for the tests) of 1428 kN, which is twice as high as corresponding experimental values from standard bored piles with similar geometric conditions. Exhumation of one of the tested piles was carried out after the test, in order to check integrity and shaft conditions. Numerical finite element analyses, using the commercially available French Code LCPC Cesar®, were performed in order to back-analyze the geotechnical soil parameters for a post execution pile condition. The results permitted a better understanding of the improvement of the subsoil given the intrinsic execution characteristics of this particular pile. It was also possible to note that drilled displacement piles have great potential to become an economically viable solution in tropical soils, given the enhanced behavior of such piles when compared to alternative (cheaper) techniques. In fact, it has several advantages which should make it a key foundation type in the Brazilian market in the future.IntroductionMost buildings in tropical soils use, as the main type of foundation, deep bored or auger type piles. These types of foundations can be performed in various ways, for example with or without soil extraction, with or without bentonite mud and so on. Two main processes maybe formulated: the first execution process is typified by bored pile types, continuous flight auger piles etc., which do not cause excessive soil displacement during excavation. With respect to the second process, one could mention, amongst others, driven piles (precast concrete or steel), Franki piles and drilled displacement piles, which do displace the soil during excavation by pushing the soil laterally around the hole in order to allow either the penetration of the pile or the excavator auger."

Jan 1, 2014

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By Pierre Beaudoin

"This paper deals with the repairs made on two damaged mills. It investigates briefly the causes of the damage, explain its nature and the design of the repair. It explains the detrimental effect on operation and the solutions implemented to reduce them. Finally, to review the follow-up required for such repairs. LOCATIONThe Holt McDermott Mine is located 75 kilometers Northeast of Kirkland Lake and 30 kilometres west of the Quebec border in Northeastern Ontario. The town of Kirkland Lake is located approximately 500 kilometres north of Toronto. HISTORYThe discovery of gold in Holloway Township dates back to early 1920. In 1984 Barrick Resources, which amalgamated with Camflo Mines, acquired more claims on the property and initiated an extensive drilling program. By 1985, the drills indicated reserve increased to 2,500,000 tonnes grading 6.8 g/mt. In 1986 a production decision was made and in 1988 the mine was officially opened.As of December 31, 1998, 4,691,507 tonnes grading 5,66 g/tonnes have been milled from 4 ore-bodies. The mill started up in June 1988."

Jan 1, 2001

By E. Fried

Cemented paste backfill (CPB) is an innovative tailings management method that consists in returning considerable amounts of mine tailings into the underground mine openings. The filled stopes thus participate to the ground support that allows maximizing orebody extraction and a safer environment for the mine workers. There are also significant environmental advantages of using CPB. Indeed, up to 50% of the concentrator tailings can be backfilled, leading to a smaller volume of problematic waste materials to be managed at the surface. Once the CPB is placed, or when the mine is flooded at its end-life, the backfill is subjected to underground water flows that may leach and spread the pollutants (mainly metals, sulphates, and acidity) which can contaminate the underground waters. The aim of this study is to characterize the leaching properties of CPB material and to identify the cement phases that ensure the metal fixation. A laboratory procedure was implemented consisting in the preparation of various paste backfill mixtures using sulphide-rich and sulphide-free materials, different types of binder, and mixing waters having various sulphates, copper and zinc concentrations. After 90-days curing time, the samples were submitted to column leaching tests. The CPB materials were flushed each day with 100 ml of deionised water during 100 days. The collected leachates were then analyzed for pH, Eh, electric conductivity and chemical composition. For some samples, a differential acid neutralisation test was carried out. The objective of this experiment is to dissolve selectively the hydrated phases by adding incremental acid concentrations. By analyzing punctually the equilibrated solutions, the composition of the dissolved phases and their metal content can be estimated. The leaching test results showed that the pH of the leachates remains alkaline during the test period. When the pH decreases under 10 (after 30 days), different behaviours in terms of chemical element release (especially for zinc) were observed. During the test, the oxidation of pyrite seems to slow down, probably due to passivating phenomena. Moreover, the differential acid neutralisation test results allowed a better understanding of the CPB mineralogy and the Zn-bearing cement phases. Zinc and the other metals seem to be fixed within a calcium-magnesium silicate.

May 1, 2007

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By Yunnen Chen

This work concerns the removal of zinc(II) and COD by means of sawdust obtained as a by-product from locally used wood. The zinc(II) and COD removal study has been carried out batchwise where the influence of physico-chemical key parameters such as tree species, pH value of solution, temperature and contacting time and dosage of adsorbent have been considered. The maximum percent removal was attained at pH 9 all for Zn(II) and COD after about 60 min. The adsorbent can be effectively desorption using 0.1 M HCl. The experimental results showed that ion exchange maybe the major adsorption mechanisms for binding the divalent metal ions to the sawdust. Sawdust was a potential adsorbent for the removal of Zn(II) from the effluent of electroplating industry.

Jan 1, 2009

By D. Gu

Shaft drilling is one of the most useful methods of driving shafts. This paper describes the application and development of the technique in coal mine construction in China.

Jan 1, 1993

It is possible to closely simulate the product sizing distribution from an industrial rod mill by the correct choice of parameters in laboratory batch milling. For laboratory batch rod milling, changes in per cent critical speed and per cent rod volume cause the product sizing distributions to move in parallel at a constant slope. For ball milling, larger sized media in batch milling grind more coarse material giving a closer simulation to the industrial rod mill product. Changing the feed size distribution by removal of coarse particles or addition of fine particles changes the product sizing distribution, but would not normally be practiced in laboratory testing. These data should be applicable to many instances where laboratory simulation of an industrial product size distribution is required.

Jan 1, 1998

By S. L. Aaroe

"TYRETHANE PRODUCTSTyrethane® is the family brand name which has been adopted by The W. S. Tyler Company of Canada, Limited to identify its polyurethane products. Since we have been manufacturing Woven Wire Cloth for over one hundred years and have been the innovator for most of the product improvements and developments of that industry, it is only natural that our first and primary efforts involve the use of Tyrethane® as a screening medium. The product is ideal for application in the mining industry and other operations where the rate of wear on existing media is exceptionally high.In the event that you have already had some experience with polyurethane it should be poirted cut that there are many grades of the material. The polyurethane used in Tyrethane® Products will be compounded in a variety of chemistries and different heat treatments will be used to develop best mechanical properties to handle specific applications. However Tyrethane® will not be a ""cure all"" but when it is properly applied as a screening medium it will assist by lowering the unit cost for screened materials.Prior to an explanation of the advantages of Tyrethane® let's review the conventional screening media whose applications may be considered as good candidates for replacement by Tyrethane®.1.,Woven Wire Cloth.2.,Perforated metal screens.3.,Rubber faced perforated metal screens.4.,Perforated rubber screens.5.,Cast steel screen segments and weldiments.6.,Profile wire.In most cases a Tyrethane® section is designed for a one for one replacement of the material now being used. It is rarely necessary to modify the screening equipment to enable you to install the Tyrethane® Product although it may be desirable to take some steps to improve the service life of hold down components such as Clamping Strips or Tension Members. Those parts can be encapsulated in polyurethane if necessary.To fabricate the Tyrethane® section we have three basic building blocks. They are: (1) Small molded segments having square or slotted openings, (2) Reinforcing material and (3) the raw liquid polyurethane."

Jan 1, 1976

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986

By D. A. Reynolds

[A few studies on the relationship of the fusion temperature of the ash of coke to that of the corresponding coal have been made on commercial high-temperature cokes. R. J. Rose3/ in 1921 compared the' fusion temperatures of the ashes of 10 coals and. the cokes produced from them and concluded tat they were in such close agreement that either figure could be used. More recently, Quarfort4/ found that the ash of coke fused at a somewhat lower temperature than that of the original coals As the ash of a coal and that of the coke produced therefrom have the same origin their chemical composition should be identical, provided that carbonization has not altered the inorganic, or ash-forming, constituents of the coal, and such alteration seems highly improbable. However, it has been shown5/ that coke is liable to contamination by iron during crushing and preparatory to sampling. Pieters6/ found that coke ash was cantaminated in this manner up to 0.4 percent. extraneous iron would lower the ash-fusion temperature because such iron may form ferrous silicate, which is readily fusible,7/ These results provide a basis for the prediction that the ash of coke will fuse at a lower temperature than that of the corresponding coil., especially if the fine grinding of the coke was done by rubbing surfaces of iron, as in a disk pulverizer or bucking plate.]

Jan 1, 1940

By Lloyd G. Fitzgerald

"The dangerous nature of explosives makes them a potential hazard wherever they are used, but they are likely to exercise their greatest harmfulness under conditions inherent in coal mining. The ease with which explosives can be detonated and the suddenness and violence with which they detonate require great care in their handling and use, if acci-dents are to be avoided. Campaigns have been waged by the manufacturers, the Federal Bureau of Mines, coal-mining companies, and other agencies to educate users of explosives in their dangers and in their proper use and care.Probably 95 percent of the explosives accidents can be attributed to poor judgment, carelessness, negligence, or chance taking. In many explosives accidents it is difficult to determine the cause definitely, as the evidence of the origin is destroyed by the blast and frequently those involved have been killed. Survivors of the accident often are of little help in determining the cause, as the accident occurs so suddenly they cannot tell what happened or prefer not to divulge the information they have because it may point to their own carelessness.A survey has indicated that about 10 percent of all fatalities in coal mines were caused by explosives accidents (excluding gas and dust explosions initiated by explosives). A list of explosives accidents by States, from 1925 to 1932, classified according to the severity of the accidents, indicated that Kentucky and Wyoming had the greatest number of fatalities resulting from explosives accidents. Records of the Bureau of Mines show that 14 coal-mine explosions occurred from January 1 to June 1, 1943. Explosives were involved in four of these explosions. Black powder caused two of the accidents and permissible explosives used in a nonpermissible manner the other two. These statistics are mentioned to show that explosives are still causing severe accidents.Elimination of the hazards associated with explosives begins on the surface. Storage magazines should have no opening, except for entrance and ventilation; ventilators should be screened effectively to prevent the admittance of sparks as well as to prevent unauthorized entrance. The interior should be kept clean and dry, and the floor should be of nonsparking material with no metal exposed. The surrounding area should be kept free of combustible material for not less than 25 feet (and preferably 50 feet) in all directions. Storage magazines should be fire-resistant and reasonably bulletproof."

Aug 1, 1944

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Ross W. Smith

Microflotation and surface chemical studies were conducted on a chromite from the Stillwater Complex in Montana and on some of the minerals usually found to be associated with such chromites. Considering the chromite it was found that aging the ground mineral in air or heating it markedly affected its flotation behavior. Much of the observed effects could be attributed to oxidation reactions involving surface chromium and iron species. Strongly acid pretreating the mineral appeared to reverse such effects. Thus, it can be concluded that the manner in which the mineral (or the ore) is pretreated is of utmost importance in its flotation. Work carried out on associated gangue minerals determined how they are likely to behave in a flotation environment and how certain foreign ions derived from a chromite ore itself can affect their surface characteristics and, thus, presumably also their behavior in a flotation circuit.

Jan 1, 1981

Producers with Zero Reportables 2007!: ?New Horizon Mine, Western Fuels Colorado LLC ?Isaacs Run HWM, ICG ADDCAR Systems, LLC ?Savage Mine, Westmoreland Savage Corporation ?South Hallsville No 1 Mine, Sabine Mining Company ?Black Butteand Leucite Hills, Black Butte Coal Company Black Butte and Leucite Hills, Black Butte Coal Company ?Buckskin Mine, Kiewit Mining Group ?Coal Creek Mine, Thunder Basin Coal Company, LLC

Jan 1, 2008

By Tae-kyeong Yeu, Jong-Choi, Cheon-Hong Min, Hyung-woo Kim, Jae- Won Oh, Sup Hong, Minuk Lee, Sung-Soon Kim, Chang-Ho Lee, Ki-Young Seong

"Collecting mineral resources from the seabed using a seafloor crawling robot is the firststep in the mining operation. The second-step is lifting the collected ore up to the water surface. For lifting through a riser pipe, prevention of pipe clogging (flow assurance) and economic and eco-friendly up-transferring is of the utmost concern.During collection of mineral ores, the production rate can be highly variable because of the variability in the distribution of the mineral deposit, variations in seafloor topography, fluctuations robot speed, and variations in performance of the mining robot, etc. Direct transfer of the collected ore to the riser pipe might cause unpredictable and serious problems such as over-loading of the lift pump, reduction in the life of the equipment, pipe clogging, severe increase of down-time, critical damage of equipment, further propagation of damages, and total failure after all.As a counter measure to these potential problems, a buffer station has been adopted, which is capable of storing the collected ore for a certain time and simultaneously regulating the transfer of the ore into the riser pipe. A pilot buffer has been developed by KRISO/KIOST (see Fig. 1)."

Sep 1, 2014