Search Documents

By John E. McCullough

The purpose of this development program is to design and develop a known volume air sampling pump for use in measuring the amount of radio-active material in the atmosphere of an underground uranium mine. The principle nuclear radiation hazard to underground uranium mines comes from the mine atmosphere. Daughter products of 222-radon, namely 214-polonium, 214-lead, 214-bismuth and 214-polonium, are inhaled by the miner, resulting in a relatively high lung cancer rate among these workers.

Jan 1, 1976

The Functional Performance Equation for ball milling circuits allows us to isolate the circuit classification system efficiency (CSE) from the mill?s grinding performance. The factors which affect circuit CSE are reviewed, with emphasis on water usage at the classifiers. It is shown that manipulation of such water usage can be carried out to improve plant grinding circuit efficiency, at times by more than 30 percent.

Jan 1, 2009

By John J. S. Sebastian

A laboratory-scale investigation was made of the basic problems involved in developing a ceramic heat exchanger to operate at high temperatures for using nuclear heat from gas-cooled process-heat reactors. Technical data were obtained on transferring heat by forced-convection from helium to air in a single-tube vitreous-alumina heat exchanger. Coolant air was passed through the annulus parallel with, and either concurrently or counter to, the flow of helium inside the tube. The data obtained pertain to removing heat from the helium. Average inside film coefficients were determined at mean surface temperatures of 200° to 1,570° F., inlet-gas temperatures of 1,450° to 2,665° F., and Reynolds numbers up to 560. The gas-to-surface temperature ratios were varied from 1.05 to 7.6. The tabulated results are shown in the appendix at the end of this report. The film coefficients of heat transfer were correlated by taking into account the physical properties of the helium at the average fluid temperature. With experimental conditions pointing to a laminar flow, the Nusselt number was found to decrease as the ratio of gas-to-wall temperature was increased to a value of 3. However, within the range tested, gas-to-wall temperature ratios above 3 did not affect the Nusselt number, regardless of the value of the Graetz number. Thus, beyond this point any increase in this ratio ceased to influence the heat-transfer relationship.

Jan 1, 1962

By A. D. Prokop, J. P. Rider

Along with increased production from longwall units has come the likelihood of increased worker noise exposures. In recent years, equipment has become larger, more powerful, and noisier than its predecessors. For these reasons, the Mining Division of the National Institute for Occupational Safety and Health (NIOSH) is investigating worker noise exposure on longwall faces and researching possible solutions to reduce this exposure. Part of this research effort involves studying the effect of covering the underside of longwall shields with acoustical material to reduce reverberating noise along the face. Experiments using acoustical absorptive insulation to cover the undersides of the shields, shearer body, and the shield supports were conducted at the full scale simulated long-wall test facility located at the Pittsburgh Research Center. Sound levels were recorded every 1.5 m [5 fl] along a 15.2 m [50 ft] section of the simulated face for all of the conditions tested. The analysis of the data indicated that a 2.0-3.0 dBA noise reduction was achieved between the shearer drums and a 4.0-5.5 MA attenuation was attained upwind of the headgate drum.

Feb 24, 1997

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By L. J. Heaslip, J. M. Toguri, T. R. Meadowcroft, R. L. Addinall

"""Pilot Plant Operations"" is a final-year core course given to the Metallurgy and Materials Science students at the University of Toronto. This course involves a laboratory study of an industrial project at an industrial site. Details of this program are discussed and reviewed after eight years of experience. IntroductionEducators in the field of Metallurgy and Materials Science have long agreed that ""hands-on"" experience is an important component in the education of metallurgical engineers. This philosophy is reflected in the undergraduate curricula of most metallurgical schools. The major problems encountered with laboratory-associated courses are the requirements for equipment, space and funds for both purchase and maintenance of equipment. For example, consider an exercise in crushing and grinding treatment in a mineral processing laboratory. Such operations require the handling of tons of material and often equipment of large size. The problems of storage of ore, methods of handling and maintenance of equipment are a few of the concerns facing the department. Considering that metallurgical departments at universities are, in general, relatively small, the support to purchase and maintain largescale equipment becomes an annual budgetary concern. In reality, universities today are not geared to operate mini-pilot plant equipment, either in terms of space or personnel.For the above reasons, in 1972an undergraduate core course called ""Pilot Plant Operations"" was introduced to the fourth year curriculum in Metallurgy and Materials Science at the University of Toronto. This course consists of I to 2 full weeks (8 hrs per day) of pilot plant laboratory study at an industrial site on a project of mutual interest with the industrial organization whose facility is being used. The first 5 years of the program were carried out at the pilot plant facility at the Ontario Research Foundation; Stelco's Research Centre in Burlington, Ontario, was used for the last 3 years. The nature of the projects undertaken during the 8-year period is shown in Table 1."

Jan 1, 1980

By W. Robert Thompson

Hurricane Katrina caused significant damage to transportation structures on the Gulf coast in August, 2005, including the destruction of the US 90 Bridge over Biloxi Bay, Mississippi. Part of the successful design/build proposal for the replacement bridge included a comprehensive test pile program of indicator piles and load test piles in the geotechnical investigation program. A total of 22 indicator piles were installed on the project using the pile driving analyzer to monitor the pile behavior. Five load tests were performed: two axial Statnamic, two lateral Statnamic, and one static axial. The results of the test pile program established driving criteria for production piles that included end-of-drive blow counts and pile tip elevations with an appropriate allowance for setup. The program also confirmed that the planned installation equipment and techniques of GC Constructors, a joint venture of Massman Construction Co., Kiewit Southern Co., and Traylor Bros., Inc., would install the piles to the design tip elevations before production piles began. An extensive program of restrike measurements at a range of times after initial driving of the indicator piles provided a systematic documentation of pile setup in the soil profiles on the site. These resistance values were used to develop a dimensionless setup factor ?S? as the ratio of the restrike resistance to the end of drive resistance. This factor varied from 1.5 for piles penetrating clays and tipped in sand to 3.0 for piles bearing completely in clay and helped establish an end-of drive blow count that included an allowance for setup. The CAPWAP analyses of restrike data with setup and the load test data were used to confirm the design unit side shear and end bearing values developed from the borings and static capacity calculations and to select the design pile lengths.

Jan 1, 2009

By Lee W. Abramson, William H. Hansmire

The H-3 Project is planning, design, and construction of a 10-mile (16 km)-long final segment of new highway that traverses the Koolau mountain range in Oahu. Interstate H-3 traverses North Halawa Valley on one side of the Koolau Mountains and Haiku Valley on the other side. The project includes a tunnel through the mountain range. The one-mile (1.6 km)-long twin-bore Trans-Koolau Tunnel will have two lanes in each direction. The total roadway width including shoulders in each bore will be 38 ft (11.6 m). The geologic and geohydrologic conditions along the alignment present a variety of tunneling problems. Geologic conditions consist of volcanic materials deposited generally in fairly thin basaltic layers. These volcanic materials generally weather down to "MH" soils which are compressible but relatively strong. Perched ground water that is recharged by heavy rainfall is present in the mountains. The paper presents results of initial geologic surveys and exploratory boring, and plans for exploratory tunneling and testing programs. A site specific classification method developed to characterize the weathered profile is presented.

Jan 1, 1989

This document is Volume II of a two-volume report on underground and surface coal mine fires occurring between 1950 and 1977. Volume I discusses the methods of data acquisition, data analysis procedures, results and conclusions. This volume contains (1) a master list of all fire incidents obtained from MSHA reports, (2) an annotated bibliography of all MSHA reports, journal articles on selected incidents, and non-reportable fires (appendix), and (3) indexes to be used in accessing incidents in the master list and annotated bibliography. These three types of information provide the reader with a complete summary of coal mine fires during the period from 1950 through 1977 and a convenient means to locate incidents of specific interest. The body of this volume is organized around two tables and a series of indexes. The two tables are master lists of underground and surface fire incidents. They are followed by 14 indexes keyed to the master list and annotated bibliography. The appendix contains three different parts: o The annotated bibliography of MSHA fire reports (one section each for underground and surface mine fires) o The annotated bibliography of journal articles about selected fires from the MSHA bibliography o A listing of non-reportable fires (one section each for underground and surface mine fires) Descriptions of the contents and use of each of the three major components of this volume (i.e., master list, indexes, and appendix) are presented in Section 2.0.

Jan 1, 1979

By Kul Bhushan

This paper presents the results of lateral load tests on 0.61-m to 1.27-m (24 to 50-inch) diameter drilled and cast-in-place piers in San Diego area residual/formational soils. The test piers were installed and tested in the following soils: Decomposed Granitic Rock (Ktd), Stadium Conglomerate (Tst), and Friars Formation (Tf). Lateral loads of up to 845 KN (190 kip) were applied to the piers in residual granitic soils, and loads up to 1780 KN (400 kip) were applied to the piers in Stadium Conglomerate and Friars Formation. The tests were conducted by jacking against adjacent piers and monitoring the lateral load and lateral deflection at the ground line. Test results indicate that ultimate lateral pile capacities of up to 1800 KN (400 kip) can be obtained for 0.61 m (24-inch) drilled piers with penetration of 3 to 6 m (10 to 20 ft) in the residual/formational soils tested. Lateral load analyses using p-y curves for very dense sand significantly overestimate the observed lateral deflections. For lateral load analyses using dense sand p-y curves, p-multipliers that increase the lateral soil stiffness (p-y curves) by 2 to 8 times are required to match the load-deflection behavior measured in the test piles. When applied to the dense sand p-y curves, the p-multipliers provide a more accurate prediction of load-deflection behavior in the residual/formational soils, and can result in shorter required pier penetration and significant savings in foundation cost.

Jan 1, 2002

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

EARLY in 1911 the Public Service Board of New South Wales suggested the advisability of inaugurating a School of Mines at Broken Hill, arid made inquiries to determine how such an institution should be conducted. He, the author, believed the Board, as a result of the inquiries, was in favour of the project being worked in conjunction with the Technical College, and hoped to be ready to receive students at the commencement of 1912. That the inauguration has not yet taken place is probably due to the vast amount of consideration and preparation that a new departure of the sort would require. At the present time New South Wales or, to speak more broadly under the same denunciation, Australia is not at all suitably catering for the technical training of young men to provide the increasing demand for officers to work the valuable mines within its territory...

Jan 1, 1912

By M. Reuter, U. Boin

The target of the current metallurgical industry is to recycle and utilize all their by-products, so as to close the sustainable production loop. Slags are the important wastes and by-products of metallurgical industry, which have been treated, recycled and used worldwide. The present paper summarizes the current status of utilization of the various slags from ferrous and non-ferrous metal production, as well as waste incineration, and recycling of salt fluxes in secondary metal production. In addition, the environmental issues of the metallurgical slags are addressed. The metallurgical oxide slags have stone-like properties and, thus, their major applications are in civil engineering field. The slags should be recycled, modified and processed in a proper way, by taking the environmental impact into consideration. With the treatment of salt slags for melting aluminium scraps, as an example, the recycling and elution properties of the salt slags are discussed. Our research indicates that the viscosity of the salt flux is increased with addition of non-metallic components, that a certain percentage of fines remain in suspension, which determines the viscosity, affecting the settling of heavier materials. High slag viscosity will lead to more fine aluminium metal entrapped in the salt slag (may also be seen as a high temperature slurry), and thus increase the load of salt slag recycling. Keywords: recycling, environment, metallurgy, slags, fluxes, salts.

Jan 1, 2004

By D. Simon

This paper studies the effect of binder type and content on the early age development of cemented paste backfill (CPB). The early age development of the mixtures is analyzed using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX). These tests show that the early age development of CPB is sensitive to changes in the paste composition. The properties of the CPB depend on the cement content and hydration time. The quantity of hydration products increases with hydration time for all of the mixtures containing cement. However, the high cement content pastes (at least 50% PC) exhibit complete coverage of the PC grains and mine tailings by C-S-H, while the low cement content paste shows scattered coverage of the PC grains and mine tailings and a higher void ratio.

May 1, 2007

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

?? Intro ?? Mass blast principle ?? LaRonde evolution toward mass blast ?? Overview ?? Mining method ?? Longitudinal ?? LaRonde evolution (2002 to today) ?? Drill and blast design ?? Consumptions and statistics ?? Mucking strategies ?? Case study ?? Examples ?? Conclusion ?? As underground mines extends to greater depths, few questions must be asked: ?? How to: keep operations safe eep operation effective reduce the cost maintain and control the dilution ?? Geomechanic method and practices; significant advances have been observed in the field of: ?? ground support ?? mining sequencing ?? Drilling and blasting; research and development has been less extensive, probably due to the following characteristics: ?? Drill and blast are mainly production-oriented ?? Drilling and blasting are more oriented toward productivity ?? Technology relies heavily on suppliers ?? Highly stressed ground conditions ?? generally help the explosives to break the rock for fragmentation ?? intensify over-breaks or blast-induced

Feb 1, 2008

By Circadian Technologies

Alertness levels naturally fluctuate during the day and night Basic functions ??digestion, body temperature ? follow predictable 24-hour patterns Adjustment to night work creates health challenges for shiftworkers Performance decreases during overnight and post-lunch dip hours Fatigue supercedes training & experience Fatigue is a major cause of human error

Jan 1, 2010

By E Apaza, R Neumayr

This paper aims to summarise the discovery of the QTS Central resource, a previously unidentified +1 Mt inferred resource that lies between two major CSA resource systems.The 1.7 Mt at 5.76 per cent Cu, QTS Central ore system represents 1/6th of the CSA mineral resource and was discovered in 2014 based on the accumulation of historic exploration records dating back to 1989.The CSA deposit consists of five ore systems hosted within turbidite-derived siltstones (CSA Siltstone) and lesser sandstones (five per cent) of the Devonian Amphitheatre Group. The host sediments strike approximately north–south with a steep westerly dip and exhibit a well-developed east dipping cleavage. Most CSA mineralisation is hosted within dilation zones at the intersection of cross-cutting structures and is interpreted as epigenetic in origin.Alteration and weak mineralisation, up plunge to the reported QTS Central mineral resource, was initially detected in 1990 during a downhole electromagnetic conductivity (EM) study, where one hole indicated an off-hole conductor, later tested with four diamond holes. One of these diamond holes intersected 3 m at 7.5 per cent Cu at 200 m. Development of the 9070 Subway drive in 2005/2006, linked the QTS North and QTS South workings and intersected structures interpreted to host QTS Central mineralisation. Subsequent drilling proximal to the 9070 Subway in 2007 identified an up plunge extension to the QTS Central zone (UDD07152: 1.8 m at 6.3 per cent Cu from 10.7 m). Work on QTS Central was largely forgotten until 2012 when the mining of a 450 m infrastructure drive provided a platform to test the anomalous grades. In December 2013, drill hole UDD13055A intersected 20.9 m at 7.2 per cent Cu from 378 m. By the end of 2014, the QTS Central inferred resource was 1.0 Mt at 6 per cent Cu and 18 g/t Ag (Hosken and Apaza, 2014). Late in 2016, further infill drilling occurred from two fronts to increase confidence in the QTS Central resource. The results of this drilling are expected late in 2017.The current interpretation indicates the QTS Central system consists of two main lenses hosted within closely bedded sandstones and siltstones. The sandstone in general is not mineralised, being heavily silicified, while the siltstone is mineralised and chloritised. The main mineralised lens is 75–200 m along strike and 450 m high. Massive sulfide feeder structures lie at the core of the two main lenses, although the characteristics of the QTS Central system tend toward the mineralisation being more chlorite-rich than in QTS North and QTS South.CITATION:Apaza, E and Neumayr, R, 2017. The discovery of the QTS Central ore system, CSA mine, Cobar, NSW, Australia, in Proceedings Tenth International Mining Geology Conference 2017, pp 151–156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977