Search Documents

By B Belle

In a predrained gassy coalmine, ventilation control plays a secondary role to the longwall (LW) goaf drainage systems to safely manage panel return gas levels. Typically, the LW specific gas emission (SGE) estimation models provide anticipated goaf gas emissions and arriving at required gas drainage capacity for various coal production scenarios. A study comparing the various LW goaf gas hole spacing patterns with weekly production rates of up to 270 kt/w of an operating mine with high SGE rates (~20 m3/t) was carried out. The goaf capture efficiency of LW panels ranged from 64 per cent to 85 per cent. For the first time, gas content of upper seam data post LW retreat were used to verify the current SGE prediction models. This study has shown that an average of 50 m goaf spacing is optimal for management of high production retreat gassy LW panels in presence of multiple upper and lower seams with gas emission zone influence reaching up to 200 m above workings. Due to the horizontal stress direction related geotechnical issues, goaf hole failures just behind the LW face is a recurring challenge resulting in significant and immediate increase in LW panel return gas levels. This paper highlights the shortcomings of current SGE prediction models for goaf gas estimation, and evolution of 50 m goaf hole spacing embedded in design process in managing the LW tailgate gas levels.CITATION:Belle, B, 2017. Optimal goaf hole spacing in high production gassy Australian longwall mines – operational experiences, in Proceedings Australian Mine Vent Conference 2017, pp 15–26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By S. T. Johansen, C. Colomb, B. Ravary

Combustion and thermal NOx formation have been modelled using the Computational Fluid Dynamics (CFD) commercial code Fluent 6.1. The aim was to predict and give a better understanding of the combustion in electric arc furnaces for the production of ferro-silicon and silicon metal. Another important objective was to assess the impact of a number of operating parameters on the NOx formation. The CFD tools used are de-scribed with a special focus on models for species and turbulence transport. Sensitivity studies have been carried out to study the influence of several parameters: sub-models, process gas composition and distribution at the charge surface and influence of the presence of SiO. The main conclusions are: ?Using the combination of a realistic design, boundary conditions and models, the simulated NOx level is in quantitative agreement with measurements. The presence of water vapor is particularly important because of its influence on the specific heat of the mixture and resulting temperature. ?Release of significant amounts of SiO from the charge surface results in an important increase of NOx, even if we applied a simplified combustion model for SiO gas. However, because of lack of thermal and compositional data for blowing situations (when SiO flows directly from the arc cavity through open channels to the charge surface), no quantitative validation is possible. The way SiO is distributed (uniformly or as a jet) has a limited impact on the result in our computations.

Jan 1, 2007

This paper discusses the application of a computerised model based on genetic algorithms (GAs), called GenRel, for reliability assessment of underground mine hoisting systems. The purpose of this paper is to investigate whether GenRel can be applied to predict future failure data of a mine hoisting system based on historical records of failures. The incentive of selecting the GAs for prediction of failures is that GAs are a class of evolutionary algorithms which imitate the biological evolution procedures such as reproduction, selection, crossover and mutation. The reliability of mining equipment changes over time due to an array of factors (eg equipment age, the operating environment, number and quality of repair). These factors affect the equipment's failure patterns and have complex impacts on the equipment's reliability characteristics. The failure patterns are assumed to follow a biological evolution process, and thus GAs can be considered applicable in the modelling process.To conduct the reliability assessment, a study was carried out with historical failure data of hoists in the time period from January to December 2007. Two failure data sets of two mine hoisting systems were collected from two typical underground mines in Ontario, Canada, which are denoted as the NA mine and the SB mine. The failure data sets were prepared in the format of time between failures (TBF). Then, these data sets were entered in GenRel to generate predicted failure data sets for the period of January to March 2008. The paper discusses the statistical similarity of the actual failure data sets for the period of January to March 2008 with the predicted failure data set generated by GenRel in the same time period.

Dec 6, 2010

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By J T. Woodcock, G J. Sparrow

A sample of pyrrhotite flotation concentrate pulp assaying 15.3 g/t Au, which had been prepared from an old tailing dump, was treated to extract the gold. Examination of the concentrate with an SEM showed that exposed or free native gold, 5- 40 ¦m in diameter, was present but no locked gold was observed. Direct cyanidation of the concentrate to extract the gold showed that the flotation reagents present inhibited gold extraction. A range of pre-treatments was used to overcome these effects. Direct cyanidation for 48 h extracted only 26 per cent of the gold, indicating possible contamination of the gold in the concentrate with flotation reagents. Pre-treatment of the concentrate pulp by aeration for 24 h, or by 72 h aeration with an addition of 3.65 kg/t of sodium sulphite, gave little improvement in gold extraction by subsequent cyanidation. Pre-treatment by filtration, or by aeration with 12.5 L/t 100 volume hydrogen peroxide, followed by cyanidation for 48 h gave gold extractions in the range 67-77 per cent. Combining filtration and an aeration period with hydrogen peroxide addition raised the subsequent cyanidation extraction of gold to 88 per cent, giving a tailing assaying 1.5 g/t Au. Re-cyanidation of some of the dried tailings from the initial tests extracted most of the remaining gold giving a tailing assaying 0.5 g/t Au. This indicated that most of the gold was available for dissolution by cyanide. The poor dissolution of gold by cyanidation of the untreated concentrate was attributed to the presence of flotation reagents. It was shown by UV spectrometry that xanthate-containing compounds were present in the solids fraction of the original pulp and that they were partly removed by pre-treatment. MIBC was also present, and dithiophosphate, which was used in the flotation step, was also probably present. The results indicated that the improvement in gold extraction after filtration and oxidation of the original pulp was due to partial removal of the flotation reagents, and illustrates the detrimental effects that residual flotation reagents can have on the extraction of gold by cyanidation of a flotation concentration.

Jan 1, 1990

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By Ray Walton, Ron Colquhoun, Ken Thomas, Dwayne Fentie, Barney Burke

"The new Roasting Facility at Barrick’s Goldstrike Mine in Nevada, U.S.A. was developed to process 12,000 tons per day of refractory gold ore. The process consists of crushing, dry grinding, roasting, extensive gas purification, calcine quenching and leaching in the presence of activated carbon. The new plant is integrated into the existing Goldstrike facility, treating ore from both open pit and underground sources.The process design, procurement, construction and commissioning of the Roaster facility was performed successfully over a 3% year period with peaks of 400 engineering personnel and 950 construction personnel supporting the project. The US$330,000,000 project was completed ahead of schedule and under budget. The commissioning was well planned and proceeded smoothly through a rapid start-up to achieve all primary goals within three months of the start of processing of ore.BACKGROUNDAs early as 1992, Barrick’s Goldstrike Mine, located north of Carlin, Nevada had indications of the ore becoming ever increasingly carbonaceous in nature. As the open pit and underground exploration programs proceeded to step out over the years that followed, the accumulative amount of carbonaceous refractory ore and tons had become significant. By 1997, 29 million tons of double refractory carbonaceous ore containing an estimated 11.6 million ounces of gold had been identified. By 2000 the resource had increased to 14.3 million ounces."

Jan 1, 2001

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981

By E. J. Gleim

The importance of "good voltage,? especially for direct-current systems in coal mines, is not always fully appreciated. From the practical 4 aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Bern Klein

Motivation for Improved Energy Efficiency in Mining ? Canada potentially adopting Greenhouse Gas Emissions and Intensity Legislation in 2013 ? BC -Climate Action Plan and Energy Conservation Agreement in 2008 ? BC Energy Plan 2007 -BC Hydro is mandated to save 50% of new load growth ? TSM Initiative -Energy Management, Energy Reporting, Setting Energy Targets, GHG Management BC MOU for Energy Conservation Agreement -MEMPR, MABC, BC Hydro

May 1, 2010

North American Coal is a subsidiary of NACCO Industries. Originally founded as Cleveland and Western Coal in 1913, North American Coal took its present name in1925. Today, North American Coal is one of the 10largest coal producers in America, mining about 32Mt/a (35 million stpy). The company mines primarily lignite for electric utilities. Its current operations are in North Dakota, Texas, Louisiana, and Mississippi. In addition, North American Coal’s Florida operation provides dragline mining services for quarries that produce more than 18Mt/a (20 million stpy) of limerock. With more than 1.8 Gt (2 billion st)of bituminous and lignite coal re-serves in the United States, North American Coal constantly seeks new technologies to keep its operations modern, productive and cost competitive.

Jan 1, 2004

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By D. W. Olson

Garnet has been used as a gemstone for centuries. However, garnet’s angular fractures, relatively high hardness and specific gravity, being chemically inert and non-toxic and free of crystalline silica, and its ability to be recycled make garnet ideal for many industrial applications. Garnet is the general name given to a group of

Jan 1, 2005

Real-Time Integration of Mining and Metallurgical Information for Efficient Use of Energy and Water

Sep 13, 2010

By S. W. Stogran

"Chemical and limited biological monitoring of mine and mill effluents are being used by regulatory agencies to monitor and control discharges to the environment. Amendments to the Federal Fisheries Act may make it mandatory for mines to conduct Environmental Effects Monitoring (EEM) which will change the emphasis from monitoring effluents to monitoring impacts on receiving waters. The EEM amendments may expand the scope of present environmental studies to include: effluent mixing zone delineation; inventory and classification of resource, habitat, and historical receiving environment; effluent quality determination; chronic and acute bioassay testing; tissue analysis; benthic invertebrate monitoring; fish population surveying; fish tainting evaluation; and the evaluation of impacts on fish habitat, invertebrate communities and fisheries resources. The requirements for EEM have not yet been worked out by the mining industry and the government committee. Experience at Lakefield Research in conducting biological monitoring studies for the mining industry has shown that biological monitoring may be useful for assessing environmental impacts only if programs are planned and executed to collect relevant data, thus minimizing costs and maximizing effectiveness.IntroductionThe chemical monitoring of effluents and water bodies receiving effluents is common practice in the Canadian mining industry and has been used routinely by regulatory agencies to control discharges to the environment. Biological monitoring has also been used on a limited basis, primarily to augment chemical data collected. A number of regulatory bodies, primarily in Canada and the United States, have been incorporating biological monitoring into environmental regulations.Various forms of biological monitoring techniques have been used in Canada and the United States to help assess the impact of mining operations and effluents on the environment. Biological monitoring includes a wide range of activities, from monitoring metal uptake in individual organisms to examining the population dynamics in ecosystems. The most commonly employed biological monitoring techniques are the chronic lethality toxicity tests. Also becoming widely used are in situ and chronic toxicity tests."

Jan 1, 1994

Willyamite from the type locality, Consols mine, Broken Hill, N.S.W., has been re-examined, and found to consist of zones with widely different Co:Ni ratios. The name willyamite is redefined to include the portion of the (Co, Ni)SbS series with cobalt in excess of nickel. Willyamite is pseudo-cubic, with the three axes equal to within 0·001 A.

Jan 1, 1970

By J. R. Thoenen

[For several years the Bureau of Mines conducted tests on ground vibration t emanating from quarry blasting in an effort to determine an index of destruction for different types of structures. Results of these studies have been published in four Bureau of Mines Reports of Invitations as well as in several articles in the trade and technical press.5/ The first paper (3)6/ discussed the subject in general and gave results s of a few blasting records. Some tentative theories also were advanced. The second paper (4) discussed results s of records made from blasting in a number of quarries.]

Jan 1, 1940