Search Documents

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

By Frank Cook

In this two-year study, an evaluation of mining and reclamation practices at 159 randomly sampled surface coal mines in the United States was conducted. It is concluded that reclamation practices in most of the 22 coal-producing states were adequate during 1975, but that improvement in reclamation performance was desirable in the acid area of the central U. S. and in mountainous southwestern Virginia. Productivity improvements should result from research to determine efficient or optimal operating procedures for dragline stripping of single and multiple seams, surface mining of lignite, multicut and multiseam haulback mining on steep slopes, mountaintop removal, and surface mining in swampy or deeply glaciated areas. Specific candidate research projects are discussed in this report.

Jan 1, 1976

By H. R. Shell

Fluorphlogopite mica was synthesized from inexpensive and abundant olivine, clay, feldspar, and sand (plus K2SiF6). The raw materials were melted in crucibles and in an internal resistance electric furnace. The melts yielded >95 percent mica. The major difficulty encountered was incomplete settling of the highly dispersed ferroalloy. This problem was not completely solved. Reducing agents tried in melts of 300 to 400 pounds were carbon, silicon, and silicon carbide. Carbon slowly reduced the iron of the raw materials, with much fuming. Silicon apparently was oxidized ahead of the melting and was ineffective under the conditions obtained. By far the best reducing agent was silicon carbide. With silicon carbide, fuming did not occur and ionic iron content of the mica flake approached 0 percent. However, even with SiC, the highly dispersed globular iron did not completely separate from the mica portion. The fluorphlogopite made during this investigation should be suitable for metallurgical use. A byproduct ferroalloy containing about 5 percent nickel, 3 to 5 percent chromium, and some cobalt was obtained. Because of the highly dispersed metallic ferroalloy, the mica was not deemed suitable for electrical or electronic uses.

Jan 1, 1962

By S. J. Broderick

[Xuge d-mp heap co:lt:.ini9: tilcu?:na3s of tons of cad ~eP~se 2r3 a failiar sight in coal-mininc regior@:. T5ey reprecei~t considergole economic 1083, are very l.u.,si~hC,ly, ?:ld t?ke un m-lch vaL-x3le qace. Cor.sequentl;r thelr remcval i~ geatlyr dezir36, ax2 my ret-sn t?-at c,m be obtained would be er;pecic.llj .a~elconre&apos; t.7 the cod ir.S..r; kry. T?.e vaste rk.t~ri..tl conpl-ises large pieces of slr.t.e, hi~h-2s&apos;. bore c~al., luqs cf cle:., ,ad finer refuse conin,= fro3 the vrtskery, Tilt 1:zshcr:r refilsn contnins sone yood coal. Rig coal and the &apos;better p~lcs of bore ere the zat~rla2.s ~15:;~itiered in this in- vest ig:?.tion. 7% Il~avter frnctions of the w~~sherjr ref;lw aizd tts large 2ieces of slcte ?,".:I rgck contilin 1it:lei ccai-i-bcna.c~o~s caterial ad are vir- tu<dly worthiess nc, rz:. ::atcrin!. for .*=irin,= zct,iv?*teb cCvb~n. 13 the 3irniingh.m district, i13br.12, a-c.ju",P p?rcccn",f the c3sl r?.ir?ed is washed, ,md in tkis c?i.;trict nlz:~c rcfilce ecc;:?:lletcs ~t the r%tg of 1 to 2 million .! tons 2 yew.]

Jan 1, 1941

By G R. Dickens, N H. S Oliver

Deformed regions of the Hamersley Province, Western Australia, contain several major iron ore deposits where banded iron-formation (BIF) of the Dales Gorge Member was converted to martite-microplaty hematite. The genesis of these ores remains controversial, in part because no study has systematically documented how stratigraphically equivalent rocks change chemically from undeformed regions into the deposits. Profound chemical and mineralogical differences do occur between rocks in the undeformed north and mineralised south. BIF and shale can be classified into three types: BIF, altered BIF and iron ore, and black shale, altered black shale and red shale. A series of low temperature (20 to 250¦C) chemical reactions can explain the observed differences in chemistry and mineralogy. The inferred reaction paths indicate that no single process could have produced all of the altered rocks at Mt Whaleback. Recently described carbonate-rich, silica-poor rocks at Mt Tom Price (Taylor et al, 2001) suggest this alteration sequence is even more complex. Our favoured explanation for the genesis of hematite ores is one that can explain deposits at Mt Whaleback and Mt Tom Price: following regional metamorphism, hydrothermal fluids locally formed carbonate-rich, silica-poor BIF with magnetite and carbonate-rich altered black shale. Subsequent surface derived fluids oxidised this magnetite, crystallised microplaty hematite (mpl) and eventually dissolved carbonates and silicates leaving high-grade ore. Either during or sometime after mineralisation, acidic, oxygenated fluids converted altered black shale to red shale and unaltered BIF to martite-rich BIF without carbonates across the southeast of the province.

Jan 1, 2002

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Rodney D. Rosenkranz

The Bureau of Mines evaluated the potential supply of primary copper from domestic mines and deposits and found that increases in copper price will be required in order for many domestic deposits to continue production. As part of the study, a tonnage-price relationship was developed indicating the quantity of copper that could be produced economically from known deposits at various copper prices and at various rates of return on the required capital investment. Costs of production are based on estimated capital and operating costs for mining, concentrating, transporting, smelting, and refining. Direct and indirect operating costs, recovery of investment, and return on investment have been included in the smelting and refining costs. Capital and operating costs are calculated in January 1978 dollars, and byproduct credits are based on January 1978 prices. Known domestic copper mines and deposits contain nearly 92 million metric tons of copper in about 14 billion metric tons of demonstrated mineralized material. These tonnages represent the current domestic copper reserve base. Approximately 74 million metric tons of copper are recoverable from the reserve base using existing technology. Of this quantity, slightly more than 50 million metric tons are economically recoverable assuming a price of 51.00 per pound of copper, credit for the recovery of byproducts, and a 15-percent rate of return on capital investment. Approximately 60 percent of the copper occurs in mines that were producing at the time of the study.

Jan 1, 1979

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau&apos;s Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By R Yang, M Lownds

This paper reports studies showing the effects of delay scatter on the peak particle velocity (PPV) of blast vibration using a multiple seed wave (MSW) vibration model developed in recent years. The case studies also show the advantage of accurate delay timing on frequency control of blast vibration. The site parameters used in one of the studies are from a case in which the MSW model has been tested and confirmed to yield accurate predictions. This study uses an open pit blast design and a tunnel design in which blast vibrations using electronic detonators are compared with those from pyrotechnic detonators. Mean peak particle velocity (PPV) and the 97.5% upper bound PPV are compared. It is found that both these values increase significantly with the increase of the coefficient of variation of the site parameter. Using an open pit blast design, the modeling shows that electronic initiation shifts vibration energy to the expected frequency for a selected point of interest. However, for the same design of nominal initiation timing pyrotechnic detonators fail to shift vibration to the expected frequency due to its large scatter of timing.

Jan 1, 2011

By Steve Kral

Globalization was the key word for the mining industry during the 1990s, just as productivity was the key word of the 1980s. And globalization will remain the key word as the industry enters the 21st century, according to speakers at the Colorado MPD Meeting held in Colorado Springs, CO in May. The meeting, put on by the Colorado Section SME Minerals Processing Division, drew about 120 people to the Broadmoor Hotel. “Operating Globally” was the theme of the 49th annual conference. Speakers addressed the reasons why mining companies have limited their spending in the United States and have moved into Third World and developing nations.

Jan 1, 1999

By David Schroeder, John Chipman

Jan 1, 1964

By C. M. Davidson, D. J. Drexler

"Sulphuric acid treated with hydrogen peroxide to destroy organic contaminants could conceivably show increased corrosivity toward carbon steel shipping and storage vessels, caused by the persistence of a peroxide residual. This paper describes work performed to determine the effect of 0-200ppm hydrogen peroxide on the corrosion of carbon steel by 93% and 98% sulphuric acid at room temperature (23ºC) and 50ºC.Steel electrodes were exposed to acid containing several peroxide levels (0. 45, iOO and 200 ppm) for up to two weeks. Specimens were removed at intervals and weight loss, open circuit potential, depth of metal loss and residual peroxide concentration recorded.Hydrogen peroxide decomposes considerably over two weeks in iron-contaminated sulphuric acid. initial peroxide concentrations > l00 ppm suppress corrosion, but the effect is lost when concentration decays below about 60 ppm. Sustained peroxide levels in the range below 60 ppm may increase corrosion rates. These phenomena are interpreted by analogy with anodic passivation."

Jan 1, 1987

By Dolea Gabriel Gheorghe

In the present paperwork is proposed an economical-mathematical model (fuzzy) that aims optimize the technological variants of the mechanized coal face. By fuzzification, the issues to solve become more flexible and allow the decision maker to acquire more variants for the functions objectively established. The description of technological solutions is carried out by a set of controllable variables of "category" type by which the type of the machinery is defined within the frame of the actual geological & mining conditions. In the paperwork are used concepts of "successions graph" and "matrix of compatibilities"; with their help a methodology to choose between different technological variants of coalfaces is proposed. It treats the problem of developing the functions that express the membership degree in vague concept. In the end it is presented an assessment procedure for the technological variants of mechanized coal face.

Oct 1, 2009

By A. J. Geldenhuys

This paper will focus on two topics, namely (1) an innovative process for the neutralization and partial sulphate removal of acid streams produced during coal mining and processing and (2)optimization of this integrated neutralization process by adding small amounts of synthetic organic polymers. The integrated lime and limestone process has been developed to neutralize acid mine water and to remove sulphate (to less than1 200 mg/l), magnesium and metals. Limestone and lime treatment is the most cost-effective technology for neutralization and partial sulphate removal of acidic/sulphate-rich water to sulphate levels of less than 1 500 mg/l due to precipitation of magnesium and removal of the associated sulphate fraction (through gypsum crystallization). Neutralized mine water of this quality may be suitable for irrigation. The process consists of the following stages: 1. Limestone (CaCO3) neutralization to raise the pH to 7 and CO2-production. 2. Lime (Ca(OH)2) treatment to pH 12 for Mg(OH)2precipi-tation and gypsum (CaSO4.2H2O) crystallization. 3. pH adjustment with CO2recovered from stage 1 and CaCO3 precipitation. Retention times of 1 hour, 4 hours and 1/2an hour were required by stages 1, 2, and 3 respectively. The sulphate level was reduced to 1 094 mg/l, which is less than the original aim of 1 200mg/l. Chemical costs associated with neutralization, using limestone instead of lime, are reduced by 69% in the integrated limestone/lime process. The overflow water from the clarifier of each of the above stages generally contains a wide variety of colloidal impurities that may cause the water to appear turbid or may impart colour. This results in very slow sludge settling rates that cause overflow water with a high degree of turbidity and colour. There are a number of successive or simultaneous stages involved in the agglomeration of particles. To get optimum neutralisation of the acid water and partial sulphate removal to below the saturation level of gypsum (i.e. 1 500mg/l), maximum sludge recovery is needed. The higher the concentration of seed crystals, the larger the surface area. Therefore, effective removal of suspended and colloidal matter from the overflow of each stage is required and can be achieved by coagulation and flocculation. The polymers PAC6 and 3095 were effectively used as coagulant and flocculant respectively. The addition of these polymers resulted in a clear overflow in each of the above stages with a very low turbidity.

Jan 1, 2003

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facilitate research on the fundamentals of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, but Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing adit has an advantage over an active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin in September 1936, with a crew of four laborers under a resident engineer. The laborers were recruited from nearby farms, and although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939

Extraction of copper from a chalcopyrite concentrate by means of a cupric chloride leach is described. Initially the concentrate is mixed with sulphur in a 9: 1 ratio, and heated to 350-400&#176;C. This converts the chalcopyrite into more readily soluble sulphides, while the iron rejected from the chalcopyrite is transformed to pyrite, which is insoluble in the leach solution employed. A two-stage countercurrent leach using a leach solution of 1 M cupric chloride, 3.5 M sodium chloride, and 1 M hydrochloric acid extracts 98 per cent of the copper, if conducted at 105&#176;C. Iron extraction is relatively low, the mole ratio of iron to copper extracted being 0.17, compared to 1.0 for unreacted chalcopyrite. After dissolution, copper can be recovered by electrolysis, cupric chloride leach solution being regenerated at the anode.Electrolytic power requirement is low, being approximately 0.5 kWh per kg of copper. The sulphur and, most of the iron entering as feed are rejected from the process in the form of pyrite, which remains in the leach residue.

Jan 1, 1974

By D Craw, L Cox, R J. Norris

The Rise and Shine Shear Zone is a mineralised low-angle deformation zone traceable for at least 7 km through biotite zone schist of the Dunstan Range, central Otago. The zone is commonly believed to be similar to the actively mined Macraes deposit. The Rise and Shine Shear Zone occurs in the immediate footwall of the Thomsons Gorge Fault, a regional scale Cretaceous normal fault that juxtaposes chlorite zone schist against biotite zone schist. Most mineralised rocks are deformed and record a progression from early stages of semiductile deformation to more brittle cataclasis. Folds in mineralised rocks trend northwards. The mineralised schist is hydrothermally altered with variable silicification, sericitisation, chloritisation, replacement of titanite by rutile and carbonate alteration. Gold is associated with pyrite and arsenopyrite and occurs in both ductile and brittle microstructures. Sheared and mineralised schist is cut by north-striking fault zones which host mineralised quartz veins. Veins in the shear zone contain hydrothermal albite. Trace element analyses show enrichment in As, U, Th and rare earth elements. Many of the above features are similar to Macraes deposit, but there are important differences. In particular, the Macraes deposit is hosted in lower grade rocks and truncated beneath by a normal fault, Macraes has no U or Th enrichment, Macraes veins have no albite and folds at Macraes trend NW-W. Rise and Shine mineralised rocks have no Cr enrichment and no hydrothermal graphite.

Jan 1, 2005

By Barnard Foo

Topics of Discussion ?Location ?Production & Mining Operation ?Mineralization ?Mining Method ?Rock Mechanics Issues ?Ground Control Problems ?Numerical Analysis ?RockmassBehaviour ?Conclusions & Recommendations ?Discussion

Feb 1, 2008

By Valérie Léveillé

As new legislation drives to lower SO2 emissions from metallurgical plants, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an amine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 byproduct stream, which can then be directed to the front end of a sulfuric acid plant for conversion to sulfuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulfuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature SO2 emissions in the treated gas can be controlled to as low as 55 mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System and what as well as which features and cost advantages for the treatment of smelter gases were key to the technology choice.

Jan 1, 2009