Search Documents

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By L. F. Stutzman, George Thodos

A new graphical method, which is a modification of that proposed by Buckley and Leverett', is presented for the determination of the displacing fluid saturation at breakthrough for frontal drive mechanisms. This method is applicable to all types of fluids, which may be either soluble or insoluble in the oil at reservoir and injection conditions. This adaptation has unique advantages in handling problems in which either liquids or gases are the displacing fluids. INTRODUCTION In the displacement of oil from a reservoir with water or gas injected into the formation or by the expansion of a gas cap, the determination of breakthrough or flood advance is important to define the initial and subordinate phases of the operation. Thus, the determination of the displacing fluid saturation at breakthrough is fundamental to the establishment of over-all reservoir production. Methods for analyzing this saturation and for calculating production rates have been previously reported1,'*".". All of these methods utilize the rate equation for linear flow developed by Buckley and Leverett1. xs = QT - Qn/A? (?fu/?Su) .....(1) Sp where f, represents the volumetric fraction of displacing fluid in the total flowing fluid within the reservoir as is defined by: fo = 1/1+ ku/kd µn/µn .......(2) Since the time, ?, necessary for the flood front to travel distance ?X is unknown, Eq. 1 cannot be solved directly for the determination of the breakthrough point. Therefore, it becomes necessary to solve Eq. 1 simultaneously with an equation representing a fluid bal-ance on the reservoir behind the flood front. To develop such a fluid balance equation, it has been assumed that the fluid composition is uniform in the reservoir behind the flood front. Based upon this assumption, the follow-ing equation can be derived from a material balance on the displacing fluid: x = (?X) s Dx ? x=0 [ Snx - Sn1 ] dx = QT - Qn/A? It is readily observed that the displacing fluid satura-tion behind the flood front, Snx, may be determined through the simultaneous application of Eqs. 1 and 3. Although the approach may vary, this objective re-mains the same for all of the previously mentioned graphical or analytical methods. After Sox is determined, it is then possible to calculate the gas-oil and/or water-oil ratios and the rates during the initial and subordinate phases of production, and thereby define the production history of the reservoir. In this presentation only the de-termination of Snx is considered, and the reader is re-ferred to the several texts in reservoir engineering2,4,5 for a complete discussion on the methods for establish-ing the production history of a reservoir. PROPOSED METHOD FOR DETERMINING Snx Since at any time the quantity, QT - Qn/A? is a constant, Eq. 1 may be expressed in differential form as follows: dxsn = QT - Qn/A? d (? fn/? Sn) sn .....(4) Eq. 4 may be substituted directly into Eq. 3 to obtain: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = QT - Qn/A? ...............(5) Eq. 5 simplifies to the expression: ? fn/? Sn ? [ Snz - Sn] QT - Qn/A? d ( ? fn/? Sn) = 1 ....(6)

Jan 1, 1958

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

This publication summarizes the in-house and contract research and development projects programed for fiscal pear 1980 by the Bureau of Mines under its Minerals Environmental Research activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau's environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. Through the years, efforts of various Bureau programs have yielded valuable information on the origin and control of many of these problems. With the reorganization of the Bureau of Mines in 1979, the Minerals Environmental Technology program was structured to consolidate these efforts into a single program that will systematically investigate al aspects of mining- and processing-related environmental pollution and damage-from initial discovery of the mineral resource to ultimate return of the land to productive use. In fiscal year 1980, the Bureau received an appropriation of about $21 million to conduct research and development work on these problems.

Jan 1, 1980

By Ike Isagon

Backfilling has become an integral process in underground mining operations, with varying cost-effective forms of application. This study is a part of an overall investigation into the backfill practices at Copper Cliff North Mine (CCNM). The mine is well-diversified in terms of backfill methodologies and practices. The mine employs different fill methods such as cemented and un-cemented rock fill, slag fill, and cemented hydraulic fill (or a combination of them) in order to fill the voids created by mining activities. The history of backfilling at CCNM has been dominated by cemented and un-cemented slag fill. Each fill method requires operating and engineering guidelines for a cost effective quality control system. The purpose of this paper is to briefly discuss the backfill methods and applications, operating guidelines, and engineering requirements at CCNM.

May 1, 2011

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners' health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker's cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM's response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM's versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner's average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By Donald W. Mitchell

Research shows that water neutralizes the explosion hazard of coal dust when present in sufficient quantity and when intimately mixed with the dust. The quantity of water required to neutralize coal dust and coal-rock dust mixtures is about equal to the limiting moisture adsorptive capacity of the dust; the adsorptive capacity increases with increase in the fineness and volatile content of the coal. Pools of water or high atmospheric humidity do not reduce the explosion hazard. Although wetted dust is less dispersible than dry dust, poor dispersibility cannot be relied on as the sole safeguard against explosion. Dust mixtures that contain water in excess of their limiting adsorptive capacity are dispersed and ignited by severe initiation sources. Pure coal dust adsorbs water with difficulty and retains water poorly; adsorption and retention is increased by the addition of rock dust the coal; the rock dust agglutinates wetted coal and assures that incombustible is present should drying occur. Therefore, it is advantageous to rock-dust wet areas in bituminous coal and lignite mines. When coal-rock dust mixtures are wetted and subsequently dried, the explosion hazard is about the same as for dust which was not wetted.

Jan 1, 1962

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By G Stanway, P Mahoney, C Griebel

The Mining Innovation – State of Play was initiated three years ago by VCI in partnership with the University of Western Australia. The ambition was to create a ‘think tank’ type platform to support industry discussion on how it is performing in terms of innovation at a strategic level, what needs to change in the industry ‘ecosystem’, and how businesses may more effectively develop their strategy and architecture to innovate for competitive advantage.The drivers for this ambition were straightforward. The industry recognises itself as being conservative with respect to innovation and it knows the business and community endowment dividend from getting better at innovation is large; however, much of the material that seeks to provide insight on innovation tends to be drawn from industries that do not have the same high capital, long life cycle and market uncertainty characteristics as that faced by mining. Material that does focus on mining innovation is orientated towards technical innovation, not innovation strategy. There exists a significant knowledge gap, and filling it is valuable to both mining businesses and communities.The 2014 Mining Innovation State of Play report (Stanway, Griebel and Mahoney, 2014), based on a survey of over 230 mining executives, uncovered a range of insights but left several questions unresolved. The people with the best perspective on these questions are CEOs. They can see the business issues with sufficient clarity and have the influence to shape both the industry and its organisations, as seen in Figure 1. Discussing these questions with the view to progressing our collective understanding was the primary reason this interview series was conducted.Unsurprisingly, interviewing 15 CEOs and Chairpersons from different industries and commodities, across the globe resulted in a broad range of views. The discussions were frank and often blunt in assessing the short comings in the industry and suggestions for improvement. This degree of candour is hugely valuable as a basis for improvement. In the end, four key areas emerged as a basis for improvement.CITATION:Stanway, G, Griebel, C and Mahoney, P, 2017. Mining Innovation State of PlayTM – iron ore insights, in Proceedings Iron Ore 2017, pp 439–442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

THE North Mount Lyell Mine is situated on the southern side of Mount Lyell at an altitude of 1750 ft. above sea-level. The average rainfall is 117 in., and there are generally several light falls of snow during the year. Despite the heavy rainfall, which is fairly evenly distributed over each of the twelve months, the climate is equable and not unduly rigorous, and, provided that the mine employee is suitably clad, it is only on exceptional days that he experiences any discomfort by becoming wet journeying to and from the mine.The majority of employes reside at Queenstown, and are conveyed by special trains to and from the top of the haulage, which is less than a mile from the mine. The mean surface temperature at the mine is 46° F., with a maximum variation from 26° F. to 85° F., the relative humidity generally being higher than in other districts. The rock temperature is 48° F. on the 200-ft. or Main Adit level, and 54° F, on the 1200-ft. level, giving a rise of 6° F. for 1000 ft. in depth.The ventilation of the mine is natural, the downcast being served by the Crown and Blocks shafts and the Crown mullock pass, and the upcast air is carried away from the workings by the Main shaft and the Nos. 1 and 2 mullock passes. The quantity of air circulating varies from 25,000 cub. ft. to 35,000 cub. ft. per minute, the greater quantity moving in the colder weather. The downcast air in traversing the wet shafts becomes saturated and enters the level at the rock temperature of 54° F. in winter and about 56° F. in summer, while temperature readings of the outcast air indicate that it varies very little.In the southern end of the mine the Blocks shaft downcast air upcasts through the different stopes, and their mullock passes, to the level above for each level to the 700-ft. level, where it passes to one of the main uptakes. The prown shaft downcast air supplies...

Jan 1, 1927

By Edwards A. B

The following note on the mineral association in the ores of the Tennant Creek Goldfield, Northern Territory, is largely based on Mineragraphic Reports Nos. 49, 89, 117 and 193 of the Council for Scientific and Industrial Research. These reports are the results of the examinations of auriferous specimens from a number of mines of the goldfield and are now supplemented by the examination of further specimens from Mt. Samuel forwarded by Mr. V. G. Martin.The Tennant Creek Goldfield lies in the central portion of the Northern Territory, about Lat. 190 35', Long. 1340 15', on the Overland Telegraph Line and about 369 miles north of Alice Springs. It comprise an area extending about 50 miles east and west, by 30 miles north and south.The geology of the goldfield has been described by Woolnough. (2)The rocks of the area are of pre-Cambrian age, and consist of talcose, chloritic, micaceous and siliceous schists of sedimentary origin, interbedded with flows or dykes of schistose quartz porphyry, and of granites which were intruded subsequent to the regional metarporphism of the area. The rocks are moderately folded, but the beclding tends to be obscured by a pronounced east-west cleavage. The most continuous orebodies run east and west, parallel with this cleavage.Numerous lenses of hematite occur in the schists, with their long axes, parallel to the cleavage, and the gold values of the field are frequently associated with such hematite bodies. The dimensions of these hematite bodies are variable but rarely exceed a length of 300 ft., with an average thickness between 10 and 30 ft.; the original vertical dimensions are thought to be comparable with their length. The lenses tend to occur in groups when they are arranged en echelon both horizontally and in depth; and erosion has exposed individual lenses to different degrees, ranging from incipient exposure to complete removal. The existence of unexposed hematite lenses at depth has been proved by geophysical surveys, coupled with drilling tests. (3)A few of the bodies are pipe-like. Many are surrounded by a casing of brecciated rock, composed of fragments of hematite and shattered country rock, and presumably caused by subsequent earth movements which crushed the country rock against the resistant hematite bodies. In the early days of the field most of the important gold occurences were found within these crushed zones, or, to a less extent, within the hematite bodies themselves.These occurrences appeared to be associated only with those hematite lenses which were intersected by quartz veins or other lines of weakness, of later origin than the crushing. This led Woolnough to think that the introduction of the gold and attendant bismuth was subsequent to the...

Jan 1, 1942

By D Craw, P Whigham, C Rufaut

Geographic Information Systems (GIS) are computerised management systems for spatial data, offering improved data management, extensive data manipulation techniques and greater understanding of data. At the Wangaloa Coal Mine, South-East Otago, ArcGIS is being used to manage, integrate, analyse and visualise the diverse range of datasets being generated from an interdisciplinary research team. GIS will assist with identifying spatial and temporal patterns associated with the current site rehabilitation strategy. This paper will present an overview of how GIS can be a useful tool for understanding ecological recovery during mine site rehabilitation.   The Wangaloa opencast coal mine, owned by Solid Energy NZ Ltd, was closed in 1989 after more than 40 years of operation. Rehabilitation efforts involving more than 60 000 native plants began in October 2001. At Wangaloa sample points were randomly selected at 100 m intervals and recorded using a differential GPS. Plant, soil and invertebrate data have been collected at each sample point. Plots of 8 - 9 plants have been established within approximately 5 m of each sample point. Since September 2003 seasonal monitoring of plant growth and survival has been carried out. Chemical and physical datasets have been generated from soil collected in June and December 2003 for each sample point. A more restricted dataset is being generated for soil collected on a seasonal basis from March 2004. Plant and soil characteristics from these datasets have been attached to each sample point and GIS layers have been created. Relationships between data layers can be explored based on their spatial patterns. Examples presented from Wangaloa include distribution of planting success and temporal variation; temporal change in pH; interpolated pH map; digital elevation model; relationships between planting success and growth with pH and organic matter. GIS is proving to be a valuable tool on the integrated project at Wangaloa.

Jan 1, 2004

By Jean-Sébastien Lambert, Joseph Kabuya, Richard Simon

Managing a highwall failure risk in an open pit mine by controlling and mitigating the impact of vibrations produced by blasting operations is key to achieving safe and cost-effective operations. The impetus behind this study was the risk of multiple bench failures in an open pit mine that was detected by Slope Stability Radar (SSR) following blasting at the foot of a highwall. The unstable high wall was over 140 meters(459.3 ft)high and 200 meters(656.2 ft)wide. The quantity of associated material was estimated at 3,000,000 metric tons(3,306,934 US tons). The overall slope angle was 44 degrees. In order to continue mining without causing the highwall to fail, this study was initiated as part of a risk management plan to mitigate this major risk by identifying mitigation measures related to blasting operations and assessing the response of the rock mass to each blast. Identifying blasting mitigation measures consisted of optimizing blasting parameters to avoid failure of the highwall. First, a signature hole operation was carried out to obtain seismic records that were georeferenced and associated with known single charges. The method used made it possible to determine the propagation velocity of the P-waves associated with the various lithologies studied and to calculate, from the geomechanical properties of the rock masses, the maximum peak particle velocities to be respected. Subsequently, the targeted area of operation was modelled with the I-Blast software in order to optimize the firing sequences to be used according to the different lithologies present. The model also made it possible to optimally predict the particle velocities associated with each blast and ensure compliance with the previously determined peak particle velocity limits. The assessment of the rock mass’s response using SSR consisted of defining alarm thresholds and an intervention plan for various possible alarms as well as quantifying the damage to the highwall from blasting. Controlling the impact of blast vibrations on the highwall’s stability was successful, as the mitigation measures used during mining did not accelerate the highwall’s movement. No upward trend in the stabilization time of the rock mass was observed by the SSR after each blast. Post-blast geotechnical inspections and analysis of post-blast deformations in the highwall also did not reveal significant damage to the highwall as a direct consequence of the blasting.

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By Thomas M. Barczak

Advancements in support technology have occurred to a large extent because of the demands of the mine operators. Shield supports are no exception. The most notable changes in shield technology in the past decade have been increases in shield capacity and life expectancy, which have increased by a factor of 4 and 7 respectively since the inception of the shield support 25 years ago. The purpose of this paper is to set goals for the future generations of longwall shields. These goals include: (1) 100,000 cycle life expectancy, (2) improved hydraulic diagnostic capability, (3) smart load control with adjustable setting pressure algorithms, (4) composite material design to reduce weight and increase shield width, (5) constant set leg cylinder design, (6) improved joint design to reduce wear and stress, (7) advancements in leg cylinder socket design, and (8) an instrumented shield to measure in-service structural component loading. These design issues will continue to push the envelope in longwall shield technology that has provided the safest and most productive mining system employed in the history of mining. In preparation for this, a historical examination of shield failures is made and recent trends in shield design are evaluated. Design practices to improve structural margins of current designs are also addressed.

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942