Search Documents

By J. R. Thoenen

This circular is part 5 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cable-way excavators, and hydraulic monitors; part 3, hydraulic, clamshell, ladder, and dipper dredges; and part 4, haulage systems in general, with particular reference to locomotive and car, hoist and car, and remote-control systems. This circular discusses the use of motor trucks, conveyor belts, pumps end pipe lines, barges and towboats, and aerial trams. MOTOR-TRUCK HAULAGE During recent years motor trucks have gained considerable ground as a successful competitor of locomotive haulage for quarries and gravel pits. Often where trucks have displaced locomotives and cars the operators readily admit an increase in both labor and total haulage operating costs but point to some other advantage as offsetting the extra expense. In other instances haulage costs have beep reduced by the use of trucks. In still others operators, having replaced locomotive haul with trucks, have again returned to the earlier method. Obviously gasoline-driven motor trucks cannot successfully compete with other types of haulage under all conditions. The apparent' growth in the number of advocates of truck haulage, however, indicates that it has passed the experimental stage and become a permanent competitor to other tyres.

Jan 1, 1936

Jan 1, 1962

By Trevor Howie, Mal Edwards

"Thiess Contractors Pty Ltd. designed and operate the Mt Owen Mine in the Hunter Valley of NewSouth Wales, Australia on behalf of the owners of the mine, BHP Coal Pty Ltd. The mine is a multiseam open cut coal operation. Mining by Thiess commenced in September 1996 following thecompletion of the coal preparation plant. The location of the mine is shown below on Figure Al."

Jan 1, 1997

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

By Adil Aledresse, Louis Mercier, Laxman Amaratunga

"The development of high capacity adsorbents with uniform porosity denoted, MP-HMS (Mercaptopropyl – Hexagonal Mesoporous Structure) using nanotechnology, and their ability to extract gold from solution, is presented. The preparation of highly effective heavy metal ion adsorbents by the incorporation of thiol moieties into the pore channels of mesoporous silica molecular sieves has been the subject of many nanotechnology research investigations. The unique feature of these nanoporous adsorbents is their ability to adsorb gold ions from ultra-low concentration solutions like mine effluent as well as from leached solutions in gold mills. The preliminary studies from laboratory simulated gold solutions show that the adsorption capacities of these materials are also among the highest reported. MP-HMS has shown the capability to adsorb 370 mg gold per one gram of the nanomaterials from Tetrachloroaurate solution (up to 37% of their weight). Experimental studies indicated that the maximum adsorption of gold (as high as 99.9% recovery). The current studies will be extended to investigate the interaction of ionic gold complexes with nanomaterials. Future development of this work may lead to either to replace the conventional CIP/CIL processes or use nanomaterials in tandem with the former, suggesting plausible use of mesoporous material in pulp, MIP or in leach, MIL, as a novel gold extraction process.INTRODUCTIONGold typically occurs at very low concentrations in ores less than 10 g/t or 0.001% (mass basis). At these concentrations the use of aqueous chemical (hydrometallurgical) extraction processes is the only economically viable method of extracting the gold from the ore. Typical hydrometallurgical gold recovery involves a leaching step followed by the separation of the gold bearing solution from the residues, or adsorption of the gold onto activated carbon adsorbent. After elution from the activated carbon the gold is further concentrated by precipitation or electrodeposition."

Jan 1, 2008

The Effect of Bulk Iron Concentration on the Copper Activation of Sphalerite at pH 9

Sep 13, 2010

Modelling and Optimisation of Direct Reduction of Iron Ore by Coal in a Rotary Kiln

Sep 13, 2010

Vein swarms in metamorphic terranes such as the Otago Schist Belt, New Zealand provide evidence of past hydrothermal flow systems leading to fault initiation and reactivation. A major episode of hydrofracturing and fluid redistribution occurred during early Cretaceous exhumation of the schist belt. As a result, presently exposed lower greenschist facies greyschists in NW Otago are pervaded by abundant quartz-filled hydraulic extension fractures with associated normal faults hosting quartz¦scheelite¦gold mineralisation. Once the effects of Cenozoic folding have been removed, a regional subhorizontal schist foliation contains an aligned array of subvertical hydrofractures striking NNW, striking parallel to a set of low-slip conjugate normal faults; the array extends over an area >1500 km2 and over a depth interval >5 km. The hydrofracture array comprises a mesh of interlinked extensional-shear and pure extension veins. These veins show mutually cross-cutting relations. Extensional hydrofracturing apparently preceded the development of major throughgoing normal faults. Low-displacement normal faults are infilled with laminated quartz (¦ scheelite) veins (

Jan 1, 2002

By Davy A. T, Hansen J. O

The causes of ferrosilicon loss from Dense Media Separation (DMS) plants, and the related properties of ferrosilicon, are identified. Two characteristics, corrosion resistance and saturation magnetisation, are examined in detail. The chemistry of the corrosion mechanism is described and its relationship to plant parameters discussed. Methods of reducing corrosion losses are proposed. Lack of particle homogeneity, and its influence on corrosion and abrasion is noted. The relationship between low magnetic susceptibility-and increased magnetic separator losses is demonstrated experimentally.

Jan 1, 1986

By R. C. Courtney, D. J. Forrester

Modern advances have led to sweep and multibeam bathymetric surveying techniques that yield three-dimensional images of the sea floor and have also produced high-powered personal computers with which to control the data and analyse the results. At Sydney, in Nova Scotia, the topography of the sea floor over the longwall workings was observed before and after mining with a precision echo-sounder in 1987-89, with sweep bathymetry in 1993 and with multibeam bathymetry in 1994-95. The results of the latter programme produced what was probably the first observation of a complete three-dimensional subsidence trough over a longwall panel 2 500 m x 168 m. The subsidence has been quantified to a sufficient degree of accuracy to allow simple trend analysis, which has shown that the pattern and shape of movements are similar to those found elsewhere but with significantly smaller maximum subsidence. A prediction model has been calibrated

Jun 19, 1905

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By R. Gensemer

A number of state and federal agencies are calling for development of aquatic life criteria for conductivity. These aquatic life criteria or ?benchmarks? are based on observed correlations between conductivity and benthic macroinvertebrate community composition, generally measured by composite metrics or indices. However, development of an aquatic life criterion for a composite variable like conductivity is made difficult by a number of factors. Based on a database from West Virginia, observed patterns of invertebrate community composition versus conductivity may instead be related to a combination of abiotic (e.g., ionic composition, habitat) and biotic (e.g., life history, colonization potential) factors. Many benthic invertebrate taxa also do not respond to increasing conductivity in a consistent relationship. Many states have determined that a composite variable, like conductivity or TDS, is not appropriate for criteria development, as many studies have shown that toxicity varies as a function of ion composition and can be mitigated by elevated hardness. We conclude that the relationships between conductivity and changes in benthic macroinvertebrate community composition are neither strong nor reliable enough to warrant derivation of a criterion based solely on conductivity.

Jan 1, 2011

By J. R. Goode

Rare earth elements (REE) and their compounds are critical ingredients in numerous necessities of modern life including: the permanent magnets used in electric motors, generators, speaker and hard drives; high performance automobile tires; catalysts; phosphors; optical glass; etc. World production of REE in 2014 was about 110,000 t with about 98,000 t/a being “Light” (LREE) and the balance “Heavy” (HREE). Unlike other mined commodities, the majority of the LREE produced in the world is a by-product and that from a single iron ore mine in China. The balance of the LREE production comes from four REE-only mines, two in China, one in Australia and one in the USA (now on Care and Maintenance basis). The LREE operations comprise very unusual flotation processes and complex hydrometallurgical plants. In contrast, most of the HREE come from a multitude of small in-situ leach operations exploiting a single, dispersed deposit in China using hydrometallurgy alone. All of the current REE operations produce an intermediate mixed REE product that must be separated to yield the high purity, individual, REE required by the market. This paper describes the processes being used to produce LREE and HREE intermediate products and the separation plants used to make the high purity REE compounds that are key ingredients in the magnets in earbuds, turbines, and automobiles; catalysts used in the production of gasoline, and so on.

Jan 1, 2016

By Drew Floyd

Five full-scale pile load tests were performed on pairs of PZ-22 sheet piles installed with a vibratory pile driving hammer. The sheet piling was installed in several locations in soil generally consisting of miscellaneous granular fills overlying soft organic silts, inorganic silt interbedded with sands and gravels, very dense glacial till and shale bedrock. The test program also included the use of tip tell tales to determine what capacity could be attributed to tip resistance and skin friction. During the design phase of the project, it was assumed that the capacity of the sheet piles driven with the vibratory hammer could be correlated with the rate of penetration. The correlation between vertical capacity and rate of penetration would be used as a basis for determination of a driving criteria from driving the production sheet piling. The sheet piling load tests demonstrated that it was not possible to correlate the capacity of sheet piling driven with a vibratory hammer and the rate of penetration. It was also demonstrated that the capacity of the sheet piles was directly related to the density of the soil at or just below the tip. The results also tend to agree with empirical equations provided by Meyerhof (1976).

Jan 1, 1989

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

By C. Bucknam, M. McComb

Mercury and silver polythiocarbonate sludge that was generated from the pilot testing of optimized mercury removal from cyanidation pregnant eluate solutions prior to Merrill-Crowe recovery of gold and silver were tested for long term stability at Newmont Metallurgical Services. Sludge samples were mixed with heap leach residue to simulate disposal of the sludge in spent or active areas of the heaps and leached for twenty weeks with water and cyanide leaching solution, respectively. Leach testing results are presented as well as analysis of the sludge using scanning electron microscope techniques down to the <1000 nanometer scale.

Jan 1, 2007

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Albert Sauveur

It is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.&apos; The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson&apos;s paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance. Physical Properties of Cast-Iron us. Its Ultimate Composition. Mr. Johnson writes that " an investigation along the lines of consumption showed that different irons have different characters totally independent of their analyses," and he declares that " the presence or absence of these elements [meaning carbon, phosphorus, silicon, and manganese] alone will not account for all, scarcely for a half, of the facts which have long been known." He further tells us that some foundries have " proved, by the most irrefutable tests, that they could take a certain iron of a given analysis and produce certain results," while with " another iron of the same analysis they could not produce these results at all." I feel confident that every experienced and thinking metallurgist will readily believe Mr. Johnson&apos;s statements and will share his views in regard to the hopelessness of inferring the

Jan 1, 1914