Search Documents

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

Mining has long been an important activity for the people of Australia . The Aboriginals used rocks and minerals in their culture many thousand years before European settlement. It was not until 1840 that silver-lead ore was discovered in the Mount Lofty Ranges , and developed as Australia's first metalliferous mine. The mining industry contributes significantly to all aspects of the Australian economy, generating substantial employment opportunities, investment and income, export earnings and royalties for Governments. While the mining industry in South Australia is small by comparison with Western Australia, Queensland and New South Wales, it is nevertheless a very important industry in the State.   With the discovery of the world's third largest Cu-Au-U-Ag resource at Olympic Dam in 1975, the State saw a period of intense exploration activity through the early to mid-1980s. However, failure to locate additional world class deposits saw a dramatic reduction in exploration activity during the late 1980s. A perceived lack of prospectivity was compounded by the recognition that exploration for such deposits was neither easy nor inexpensive in South Australia because more than 80% of the State is masked by surficial sand and silt.

Jan 1, 1995

By J Merrells

Fluor, together with our clients, has yielded significant reductions in the total cost of mining projects by employing a systematic and methodical process of cost reduction. This paper outlines this structured approach to reducing the total cost of projects through the gathering of information, the evaluation of the zero base design, and the development of the execution strategy for the project in the study phase.Over the recent iron ore boom the cost of growth projects escalated rapidly due to a variety of factors including the engineering cost of re-designing facilities, construction in remote areas and an increase in the ‘perceived’ capital requirements for maintainable and operable facilities.Fluor has made strategic steps towards safely reducing the capital intensity of projects, by working with clients to develop zero base designs which utilise the minimum technical requirements in order to meet the function of the plant and then add cost for safety, maintenance and operability only where clearly justified.This paper has set forth a structured three phased approach to focus the team on reducing capital cost while maintaining a low increase in engineering effort.The initial ‘gather’ phase focuses the team on acquiring information and identifying decisions that will need to be made so that the team can prioritise and focus the attention on areas that will provide the greatest benefit. Within this phase the identification of zero base design requirements, review of lessons learnt and analysis of capital cost levers, allows the team to identify the key decisions on the project that will affect the capital cost.In the subsequent ‘evaluation’ phase the team established the zero base design, using the hierarchy of cost reduction as a guide to focusing the team’s attention on high yielding cost saving opportunities.In the final phase the team develops the execution strategy which will yield the least cost using strategies and tools such as modularisation, standardisation, replication, strategic sourcing and 3D design.CITATION:Merrells, J, 2017. Reducing total project cost in the study phase using zero base design, in Proceedings Iron Ore 2017, pp 621–626 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

The proper selection of a coal for a particular use depends on knowledge of fundamental data concerning the coals that offer, particularly their type and rank. Type of coal depends on the nature of the original plants and the environment in which they accumulated.Rank reflects the subsequent metamorphism of the coal, and is of two kinds-physical rank and chemical rank.INTRODUCTIONIn the different coalfields of the Commonwealth of Australia there occur many different kinds of coal which provide the coal-research worker with a wide range of material, but to the fuel technologist they represent complex problems in utilization.In the past it has been common practice to instal coal-using equipment of a design based on plant used in large industrial centres of other countries and then search for supplies of suitable coal. This has led to the transportation of coal mainly from New South Wales to other States, which have inadequate supplies of coal suitable for use in the equipment they have installed. However, modern economy and industrial practice demand local resources of coal for the development of industry, transport and domestic services, and a change in the old order is rapidly taking place. Technologists and engineers are now faced with the problem of designing and installing equipment to use whatever kind of coal is available in local coalfields.Much has been accomplished in this direction and important investigations are at present being carried out, but there still remains a wide field of problems for research.In planning and carrying out investigations into coal utilization it is essential that fundamental data and knowledge should be available and that its significance should be appreciated.

Jan 1, 1955

By M. Olper

The change in regulations and the strong attention to the environment have suggested some changes in the traditional processes for the recycling of lead acid batteries. Engitec Technologies, marketing the Integrated CX® System, is continuously updating and improving its technology to fulfil the technical, economical and ecological requirements coming from the market and from the environmental authorities. In this paper Engitec Technologies will present the latest technical innovations introduced in the Integrated CX® System.

Jan 1, 2008

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By Marc Ruest

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC?s Granger Mine, Meikle Mine, and Getchell Mine. A ?split-pipe? laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

May 1, 2002

By J. N. Van der Merwe

In the process of pillar extraction, pillars are seldom if ever extracted completely. The pillar remnants, or snooks, play an important role in the extraction process. At the working face, they need to be stable to provide a measure of support in the immediate area. Further back, they have to fail in a controlled manner to prevent undue load build-up on the pillars that have not yet been extracted. The stability condition at the working area is the result of interaction between the stability of the pillar and that of the roof rock. It is shown that the primary mode of roof layer failure is by bending induced tension. Direct tension can be excluded in most practical conditions, and only in exceptional cases will the first failure be in shear mode. Panel spans required to cause the first goaf to be formed, predicted using analytical considerations, are of the same order as has been observed in practice. Once the first goaf has formed, the horizontal stress is reduced and failure will occur at more frequent intervals. It is shown that bending induced tension is the most likely mode of failure in an unjointed roof layer. In roof layers with a high frequency of weak or uncemented jointing, failure can be expected to occur at spans equal to the joint spacing. In this context, failure will occur at the smallest of the spans required to induce tensile roof failure and the joint spacing. A fundamental procedure to evaluate the likely roof layer failure in a stacked beam system is developed. This can to be used to estimate the loading condition on snooks. It is shown that snooks assist in stabilizing the immediate roof beam. The sizes and positions of the snooks relative to the position of the next pillar to be stooped, control the magnitude of the contribution to stability. The further the snook is from the next pillar, and the larger it is, the greater the contribution to the stability of the immediate roof. Under the condition of loading by the immediate, continuous roof beam, the position and size of a single snook controls the load acting on it. The closer it is to the nearest solid, provided that the roof overhang extends beyond the snook, the greater the load on it. However, once the immediate roof beam fails, the loading conditions change. The snook is then loaded by the tributary area load. A procedure is developed to assess the condition of snooks for different situations. Using the fundamental considerations developed in this paper, snooks can be designed to be stable during the active mining phase in their immediate vicinity, but to fail once the next line of pillars has been extracted.

Jan 1, 2005

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

Heavy mineral deposits are becoming more complex in terms of their compositional variation, particle mineralogy and size distributions, and present challenges for the operation of separation equipment to achieve the required grades and recoveries. Changes in equipment design and concepts potentially provide new opportunities for the beneficiation of heavy mineral sands deposits. The development of a framework for the fundamental understanding of separator performance issues is a first step to develop new machines. This paper will present a first step analysis of electro-static and magnetic separation machines with their application to real separation scenarios.

Jan 1, 2010

By Galen G. Waddell

The Deep Creek zinc and lead mine afforded an excellent example of a relatively small underground mine operation that approached the low mining costs of large, highly mechanized mines, An open stope mining method incorporating sublevel benches and vertical long holes was used (fig. 1). Detailed descriptions are given on the exploration program, stope development, stoping procedures, and pillar removal. Pressure grouting was used to check the inflow of water and thus prolong the life of the mine. Statistics on mining costs and on electric power consumption, haulage from mine to mill, and milling costs are included.

Jan 1, 1963

To provide a faster means to open and close permissible electrical enclosures. Approach: An inspection and repair port with a multiple start thread which provides a permissible joint has been developed and tested. How It Works: The inspection port screw thread has a large pitch, which allows the port cover to be rotated from fully closed 10 fully open, in less than one revolution. See Figure 1. When the cover is screwed back in. it be-gins engagement within one eighth turn because the screw design has eight separate threads. To prevent Its unauthorized opening, the port cover has a bolt guarded by ears which accept a padlock. The threads are designed to tolerate a reasonable amount of grit without binding, although wipe-off cleanness is necessary during reassembly. Enclosures of two different sizes each fitted with the quick-access port, were

Jan 1, 1976

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1956 and 1956 are presented in this publication with a minimum of interpretation and comment because of the numerous tables required to afford detailed comparisons between the 2 years. Corresponding table., for 1955 and 1956 follow in consecutive order under the following general sections: (A) General injury experience: Tables I to II: contain current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury data: Tables 12 to 77: Contain current data on causes of injuries, distribution of injuries by part of body injured, clays of disability, extent of hand and machine loading, experience by employment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation's coal mines. (C) Injury experience, by States: Tables 78 to 87: Contain data on injuries, injury rates, employment, cause of injuries, aid severity rates by States. (D) Major disasters: Table 88: Contains data on major disasters, 1947 -56. A major disaster is defined as a single accident in which, or as the result of which, five or more persons are killed instantly or died at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 89 to 93: Contain data on fatalities and their causes at bituminous-coal and anthracite mines from the earliest records through 1956.

Jan 1, 1960

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

By W. J. van Niekerk

Ballast Nedam is in Surinam constructing two bridges that will improve communications in the coastal region. The bridges will cross the Coppenam and Surinam rivers and will be founded on open-ended steel piles over 60 meters in length. The majority of piles are inclined and support prefabricated concrete girders forming the roadway. In most locations the stratum is consolidated cohesive layers extending to a depth in excess of 60 meters. For this reason, before pile driving operations commenced, it was decided that a number of test loads would be carried out determine the capacity of the piles. Loading tests were carried out on specially installed piles as well as on piles that would be used as working piles to support the structure. Working piles were dynamically tested using Pile Driving Analysis (PDA) equipment. This decision was based on the inclination of the piles, the cohesive nature of the soil and the increase of strength after the piles are driven. A good insight has been obtained into the real strength of the soil by comparing dynamic and static loading tests on vertical test piles. This made it possible to determine the required length of pile.

Jan 1, 2000

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008

A study of drilling data at various stages of development of an orebody show that the semi-variogram, used for calculating the accuracy of block estimates can be ill-defined if too few data are available. The consequencesin this case are to have blocks supposedly more accurately known than is possible at the early drilling stage; such a result being potentially dangerous. However, as the amount of data increases the recalculated, semi-variograms approach the underlying semi-variogram of the deposit and the calculations made using them become more reliable and robust.

Jan 1, 1977

By P. H. Davenport, L. W. Nolan

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Geochemical mapping provides a direct approach to delineating areas of epigenetic mineralisation and for relating the regional distribution of this mineralisation to an overall tectonostratigraphic and structural framework, as well as to extensive areas of hydrothermal alteration. Organic lake sediment is a widely available and effective sampling medium for regional geochemical mapping in Newfoundland, that has proved to be valuable in Au, Sb and W exploration

Jul 1, 1991