Search Documents

By Zhihua Wang

Through metallurgical calculation and process analysis based on metallurgical theory, it is aimed to raise the concentration of smelting oxygen and improve the update speed of reaction interface, accelerate the reaction and achieve a high-intensity smelting at the stage of converting. The PM plant has launched a theoretical research on model of high-intensity converting aiming at increasing the oxygen concentration of converting, carried out transformation of Kaldo furnace converting system, performed a series of industrial trial operations, conducted multiple rounds of tracking test and data comparison in reducing the furnace cycle, lowering the unit consumption of fuel and stabilizing the furnace lining life. The move has practically tested and verified the correctness of high-intensity smelting theory.

By Huimin Lu, Min Li, Jinghua Zou

"Zeolitic imidazolate frameworks (ZIFs) are new type of porous materials, form inerratic polyhedral in three-dimensional with large cages and small apertures, and appear structural diversity. Their hole size can be adjusted. These materials have high selective adsorption capacity to carbon dioxide. In this paper, zeolitic imidazolate frameworks were synthesized by solvothermal synthesis method with dimethylformamide (DMF) as solvent and structuredirecting agent, divalent metallic ions as cation, and imidazole as ligand. The crystals were characterized with XRD, SEM for their crystal structures and physical properties, the adsorption of the crystals for carbon dioxide was also tested, and the result suggests that these porous materials have a capacity of 1.35ml/g for storing carbon dioxide at 273 Kelvin under ambient pressure.IntroductionGlobal warming caused by the increase of carbon dioxide in the atmosphere has become one of the main environment problems, contemporary research has focused on ways to slow or stop this trend. CO2 capture has attracted attention due to the potential to trap and sequester large amounts of CO2 from concentrated sources such as power plants [1]. Traditional technologies in capturing CO2 include absorption by aqueous amines [2]. However, utilization of this process is energy intensive and expensive. Carbon dioxide storage materials investigated so far can be divided into two categories: chemical storage adsorbents and physical storage media [3]. The first kind of materials can chemically adsorb carbon dioxide within their structures and need thermal energy to release the adsorbed carbon dioxide. The examples of the chemical adsorbents include aqueous amines, gas-hyperbranched aminosilicas [4]. The physical adsorbents store carbon dioxide by physical adsorption of carbon dioxide at elevated pressure and release the adsorbed carbon dioxide at low pressure. The physical adsorbents that have been investigated for carbon dioxide storage include zeolites, carbonaceous materials and other porous materials. Until recently, a new type of microporous material, known as zeolitic imidazolate frameworks (ZIFs), has been reported as promising adsorbents for carbon dioxide storage [5 ~ 10]."

Jan 1, 2010

By Zhang Hanbo, Niu Liping, Zhang Zhiqi, He Jicheng, Dou Zhihe

"Rutile, ilmenite and Al-Ca complex reducer were used to prepare high titanium ferrous alloy by enhanced reduction-SHS method. The effects of the complex reducer compositions and slag types on the enhanced reduction-SHS process were investigated. The high titanium ferrous alloys were characterized by XRD and SEM. The results indicate that the high titanium ferrous alloys consist mainly of TiFe2, AlTi3 and Al2O3. The oxide inclusions exist resulting in directly the high oxygen content and micro-structural defects in the alloys. The titanium and oxygen contents decrease, but the aluminum content in the alloy increases while the mass ratio of calcium in the Al-Ca complex reducers increases. When the mass ratio of Al/Ca in the Al-Ca complex reducer is 6:1, titanium, oxygen and aluminum contents are 63.75%, 3.01% and 10.72% respectively. When the mass ratio of Al/Ca is 5:1 titanium content is 55.00% nearly and aluminum content is higher than 14.00%, but oxygen content is lower than 2.0%.1. IntroductionThe high titanium ferroalloys with 65%~75% titanium have the advantages of low melting point and high titanium content. They are widely used in special steel refining, while they are also a kind of very important quality orientation alloys in the rage of aviation and aerospace. At present, the methods of preparing high titanium ferroalloy include vacuum remelting and thermit reduction. The alloys prepared by the vacuum remelting method have good qualities and low oxygen content, so it is widely used in Russia, Western Europe and other developed countries. In China, there are abundant rutile resources, but waste titanium is lack, therefore, the preparation method is the thermit reduction. But there are many quality defects in the high ferrotitanium alloy, including high oxygen content, unstable quality and so on. In order to improve the qualities of the high titanium ferroalloy, especially to reduce oxygen content, the domestic and overseas have done a lot of further researches. For example, Sichuan E-mei ferroalloy plant and Beijing Nonferrous Metal Research Institute have prepared high titanium ferrous with 73.77% titanium with natural rutile, but the oxygen content is high. Through controlling the quality of raw material, they obtained the better qualities, but the oxygen content is still very high. South Africa Mintek company have prepared high titanium ferrous alloy with low nitrate by plasma heating under the isolation air conditions, but they couldn’t also remove effectively oxygen in the alloy. The oxygen exists in the form of Al2O3 and titanium protoxide. So it can be speculated that except TiO2 not being fully reduced, the no-sufficient alloy-slag separation is the direct reason resulting in high oxygen and poor microstructure. In view of present technical difficulties during preparing high titanium ferroalloy by thermit reduction, this paper proposed a new method of preparing high titanium ferrous with low oxygen by enhanced reduction-SHS with Al-Ca complex reducer. Ca in Al-Ca complex reducer has stronger reductive ability, it can effectively strengthen the reductive degree of TiO2. The slagging agent CaO CaF2 and MgO can effectively reduce the viscosity of Al2O3 slag to improve its liquidities to strengthen alloy-slag separation effects so that to remove inclusions and oxygen. In this paper, effects of slagging agent type on the reduction and the qualities of high-titanium ferroalloy were studied."

Jan 1, 2012

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By Yoichi Takeda

The CaO-FeO,-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By Yoichi Takeda

The CaO-FeOx-Cu20 slag has been practically applied to continuous converting of copper, and also has potential for refining of copper. Liquidus lines of the slag system and phase stability diagram for the liquid slag and the existing solid compounds under copper saturation are presented. Liquidus composition was determined by chemical analysis of slag sample saturated primary solid. The temperatures of invariant equilibria were investigated by thermal analyses. Oxygen potentials on the liquidus lines, the univariant and invariant equilibria were estimated from the relation slag composition and oxygen potential that relation was confirmed in separate experiments.

Jan 1, 2003

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By D. Papazoglou

This work was undertaken to investigate the thermodynamic and kinetic feasibility of using hot sulfur dioxide bearing gases from smelting processes to selectively sulfate the nickel in nickel laterite ores for subsequent extraction in water. The environmental benefits of this approach, as opposed to releasing the gas to the atmosphere, and the economic benefit of directly utilizing the SO2 rather than converting it to sulfuric acid are strong drivers for such a process. A thermodynamic analysis indicated that selective sulfation of the nickel could be feasible under appropriate conditions and these were explored through a series of laboratory scale experiments. Laterite samples were reacted at temperatures between 500 and 800°C with an equilibrated mixture of sulfur dioxide, oxygen and nitrogen in a fixed bed reactor. Tests were conducted on saprolitic ore from Bulong, Western Australia:, limonitic ore from New Caledonia and gamieritic ore from Indonesia. Nickel extractions were highest from the limonite and relatively low from the other ores. The maximum selective extraction of nickel from the limonite in a single stage sulfation was 73%. Sulfation of other elements present in the laterites was also examined. A two-stage process was also identified which involved sulfation using a strong sulfation potenrial followed by weaker sulfation potential to attempt to convert ferric sulfate formed in the first stage to ferric oxide. This increased the extraction for the limonite ore to around 84% Ni, 95% Co and 2% Fe. Direct sulfation of laterite could be feasible in locations where sulfide smelting or roasting operations are relatively close to laterite deposits.

Jan 1, 2003

By Naixiang Feng, Shaohu Tao, Zhihui Wang, Yuezhong Di

"A novel vacuum aluminothermic reduction lithium process was developed in present work which used lithium carbonate, alumina and calcium oxide as raw material. The process mainly contained three steps. The first step is that LiA102 clinker is prepared in ambient environment, then metal lithium is vacuum extracted from LiAl02 clinker with aluminum power as reducing agent, and the last step is that alumina is leached from the reduction residue with a mixture of sodium hydroxide and sodium carbonate. The results show that the lithium reduction ratio can be over 95% under the conditions of reduction temperature 1423K, reduction time 3h, and aluminum excess 20%. The main components of reduction residue are CaO· Al203 and 12Ca0·7Alz03. The alumina leaching rate of calcium aluminate in residue is over 80%. High-whiteness aluminum hydroxide can be obtained by carbonation precipitation of the reduction slag leaching solution.IntroductionWith a density about half of water, lithium is with the lowest density of all solids, mere 0.5 g/cm3 at 20 °C [l]. Lithium is widely used in aerospace, aviation, nuclear-generated power and electric battery industry. Nowadays, over 90 % of the world's primary lithium is produced by molten salt electrolysis [2-4]. But the development of molten salt electrolysis will be effected by some factors: cost, environment, and so on. Vacuum thermal reduction may be used extensively in future because of its low-energy consumption, high-purity and short-cycle."

Jan 1, 2013

Based on experimental and computer simulation results from our group, we report a systematic, atomic level analysis of carbon dissolution from carbonaceous materials in molten iron. Experimental results on graphite/Fe-C-S system were obtained using carbon dissolution studies, XRD and FESEM investigations and were supplemented with Monte Carlo simulations. Three basic mechanisms, namely carbon atom dissociation rate, interfacial phenomena and mass transfer in the melt were found to be responsible for the overall dissolution process. While mass transfer in the melt is governed by the concentration gradients, melt composition and temperature; impurities present in ash play a significant role in the interfacial phenomena. For less ordered forms of carbonaceous materials, carbon atom dissociation rate depends strongly on the degree of long-range order and is an important rate controlling mechanism in the overall dissolution process. A systematic comparison of dissolution rates for a variety of coal-chars, natural and synthetic graphites has been carried out in an attempt to identify rate-controlling mechanisms. The structure of the carbonaceous material appears to be an important underlying factor in the carbon dissolution process.

Jan 1, 2003

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By R. H. Crist

Reactive components of algal cell walls include uronic and alginic acids: In addition, many marine species have half ester sulfate groups which function as fixed anions. Associated metals vary with the media, eg., Ca and Mg in fresh water (FV) and Na, Ca, Mg in seawater. . These metals readily exchange with aqueous phase protons or metal cations. A plot of the total amount of metal cations displaced by protons vs .. pH shows one inflection at pH 4 for FV algae and' in addition a second inflection at pH 2, 3 for marine algae. The first inflection is interpreted as. Indicating the cations associated with carboxyl groups ,and the ,second with half ester ?Sulfate groups. The exchange capacities of various aigal ,species vary widely. When FV algae is placed in a Pb2+ solution,- the amount of Pb2"' deposited on the algae is. Equivalent to the. Total Ca2?, Mg2, and H+ displaced? thereby confirming the ion exchange mechanism. Ion exchange equilibrium constants are reported for the displacement of ca2+ from Vaucheria. With Mg2+, sr2+, Cd2+, Pb2+_ and Na+ as well as the reverse reactions. Cd2+ can .be removed partially from algae by precipitating it as CdS or Cd(OH) 2 Pb2+ and Cu2+ are also partially removed as the hydroxides. Rates of reaction for various alkali hydroxides decrease with increasing .unhydrated cation radius. It is concluded that theory is useful in predicting viable applications for algae in pollution abatement.

Jan 1, 1991

By Guy L. Fredrickson

A modified transpiration reactor was used to measure the composition of the equilibrium gas phase formed above compounds in the Hg-O-S system at high temperatures (600 to 900K). A thermodynamic database {(AGo°f AH°t. AS°t)} for-HgO, HgS, HgSO4, Hg2SO4, HgSO4?HgO, and HgSO4?2HgO was developed based on the experimental results. Prior to this study, only estimated data were available in the literature for the sulfates and oxysulfates at temperatures above 298K. A series of vapor pressure' stability diagrams were constructed from 473 to 973K with isobars of Hg(g), HgO(g), S2(g), and SO3(g). These diagrams were found to be significantly different than those available previously and do provide insight to the phase relations of importance during the thermal processing of Hg-containing wastes. The thermodynamic results were used to conduct a series of Gibbs energy minimization calculations for a thermal processor' afterburner system for the treatment of HgS-containing wastes. The retention of Hg in the discharge calcine was examined as a function of temperature and excess air. Hg was found to report to the calcine as HgSO4, Hg2SO4, or HgSO4 HgO depending on the process conditions, and Hg retention occurs at temperatures as high as 930K. The precipitation of Hg-containing phases from cooled afterburner discharge gas starts at approximately 900K and the cooling of the gas an additional 30K (to 870K) results in over 50% of the Hg being preCipitated as HgS04?HgO. It was also determined that for small amounts of Hg present in sulfide concentrates during roasting, the Hg will be retained as HgSO4 or HgSO4?HgO at temperatures as high as 870K.

Jan 1, 1996

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

By Veena Sahajwalla

The cupola furnace is a coke-fueled shaft furnace used as a primary melting unit in iron foundries. Control of chemical composition of the iron tapped from the cupola is a key factor in productivity and quality control. In an effort to develop a control model for the cupola, a fundamental approach based on physical and chemical principles has been taken to describe the melting process. The behavior of oxidation of the solid charge in the stack of the cupola has been studied. Sulfidation of the charge materials by sulfur-bearing components released to the furnace gases from the coke has been described. Carburization of metal droplets of iron and of steel in separate molten streams has been characterized. Finally, reactions with alloying elements in the hearth (well) of the furnace have been defined. These reactions have been described in a computer-implemented model developed to predict the composition of the iron tapped from the cupola. The model has utilized the thermodynamics and kinetics of the oxidation, sulfidation, and carburization reactions, including temperature and physical aspects, in the various zones of the melting unit. The model predictions have been compared favorably with operating results.

Jan 1, 1992

By Andrew Case

The Port Nickel facility in Braithwaite, Louisiana, is known for pioneering hydrometallurgical processes for the 'separation and recovery of nickel, cobalt and copper. Ten years ago, in 1985, a new CRI-MET process for the recovery of molybdenum, vanadium, nickel, cobalt and alumina from spent catalysts was developed and implemented. Spent- catalysts from the petroleum industry consietute the majority of feed. These are not only a valuable-source of metals, but due to EPA regulations are frequently classified as hazardous under RCRA. Molybdenum and vanadium are selectively leached in an oxidative hydrothermal step. Alumina is then extracted in a caustic digestive leach. The unique technology produces four primary commercial products l molybdenum trioxide, vanadium oxide, aluminum trihydrate and nickel-cobalt concentrate. This paper discusses the process, modifications. during ten years of operation, and the relationship of these modifications to the future of the catalyst recycling business.

Jan 1, 1995

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG, HUI XIAO

Oxygen-rich side blow bath smelting (OSBS) technology was developed in 2000 based on Vanyukov process. This technology exceeds the traditional pyrometallurgical methods by its great processing capability, high metal recovery and environmental-friendly property. In the past 15 years, OSBS technology extended its application area from lead industry to bismuth, antimony and waste recycling industries, etc. This paper introduces the history and new developments of OSBS technology. The typical industrial applications examples of the OSBS technology in China, including high lead slag reduction, low grade bismuth-lead concentrate smelting and metallurgical waste recycling, are reviewed. Especially, the unique furnace properties and technical parameters are compared. Finally, the potential research directions of OSBS technology are summarized.

Jan 1, 2016

By F. H. A. Abdalla

A process is described for the recovery of valuable nonferrous metals from steelmaking dust by suiphatizing roasting using ammonium sulphate. Maximum recoveries of soluble metal sulphates achieved at optimum conditions were> 99.0 %. Selective metal separation of the soluble sulphates in the leached liquors were performed either by controlling the roasting temperature or by adjustment the pH values of the leached liquor ranging from 3.6-6.2. Either pure zinc oxide orland tin oxide could be obtained at optimum conditions, and the products were evaluated chemically and by X-ray analyses. The residues rich in iron oxide can be removed and recycled. The mechanism of sulphatizing roasting process was considered. A general flow-sheet for the overall process of treatment the steel making dust to recover its valuable nonferrous metals was suggested, which ca be applied for other nonferrous bearing materials.

Jan 1, 1996

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around I 100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003

By Torn H. Okabe

A fundamental study was conducted with the purpose of establishing an environmentally sound recovery process for recycling of valuable metals, by combining scraps containing such metals. As an example, direct extraction and recovery of neodymium (Nd) in magnet scraps was investigated by utilizing liquid metal as an extraction medium. It was found that liquid magnesium (Mg) is a suitable extraction medium and can extract Nd from iron alloys with high efficiency at around 1100 K. The newly developed extraction apparatus for Nd is a mechanically simple and static device without moving parts, where the Mg extraction medium circulates due to differences in the temperature inside the reaction vessel. This developed device can simultaneously accomplish continuous extraction of metal Nd from scraps, re-extraction of Mg from Mg-Nd alloy and the eventual recovery of pure Mg. As a result, metal Nd with 98 % purity was directly recovered from magnet scraps under certain conditions. It was also shown that the extraction agent Mg could be reused. The results of this investigation show the possibility of establishing a new process for the direct extraction of Nd in pure metal form without oxidization.

Jan 1, 2003