Search Documents

By J. R. Kiji

The Cerro Matoso S.A. mine and smelter, in the Cordoba lowlands of northwestern Colombia, consist of a dedicated laterite nickel mine, ore blending, drying and an RKEF process to produce high-quality ferronickel. At a project investment of $400M, first production of ferronickel was in September 1982, and in its inaugural year CMSA produced 6,150 tons of contained Ni from a mined ore grade of 3.2% Ni. Initial operational difficulties resulted in a number of furnace run-outs, which impacted ramp up to design ore throughput of 128 dry t/h Since then CMSA has steadily incorporated process improvements and initiatives to take the single line operation to an ore throughput of 175 dry t/h. A second 175 dry t/h line was added in 2001 (investment of US$ 300M) to consolidate CMSA as one of the world's lowest cost Ni producers with an installed annual production capacity of 50-55,000 tons Ni. The most recent addition is commissioning of Phase I of an ore-upgrading project to counteract the effect of declining ore grades. Keywords: Laterite, ferronickel, pyrometallurgy, smelter.

Jan 1, 2004

By Xie Zhang, Chongyang Zhao, Qingyun Huang, Bing Xie, Xiaopeng Zhen

"Extracting vanadium from vanadium containing hot metal into vanadium slag by BOF is the main vanadium production process in China. In this paper, the influence of Si content in hot metal on the quality of vanadium slag is analyzed. Synthetic vanadium slag with different SiO2 content were melted at 1673 K and then cooled to 303K at the cooling rate of 3?/min. Optical microscopy, SEM, EDS and XRD were used to analyze the mineralogical phases and crystallization behavior of vanadium slag. The results show that vanadium slag mainly contains spinel phase and silicate phase; V is enriched in the spinel phases while Si is concentrated in Fe2SiO4 CaFeSi2O6 and (Fe,Mn)2SiO4 as silicate phase. The melting point of slag increases gradually with the addition of SiO2; whereas viscosity decreases with an addition of 15~19% SiO2 and increases with an addition of 19~27% SiO2.IntroductionVanadium is an important element which is used almost exclusively in ferrous and non-ferrous alloys. The major vanadium products include FeV, V2O5, V2O3, VN and Al-V-Ti alloy. Furthermore, vanadium slags are mostly produced by oxidizing the elements in V-containing hot metal during a duplex refining process. Therefore, the process of removing vanadium from hot metal has its significance on the subsequent process[1].The extraction of vanadium is greatly affected by the mineralogical composition of vanadium slag[2], the distribution of the elements between the spinel and silicate phases and its physic-chemical properties. These characteristics of vanadium slag have been studied in some details. It has been reported that Si mainly exists mainly in the form of silicate which wraps the spinel crystals while small amount of Si stands as phosphorus quartz or diopside[2]. Chen et al.[3, 4] points out, when SiO2 content in vanadium slag increased every 1%, V2O5 decreased 1.48%. Moreover, silicate phases would embarrass the oxidation of V-containing spinels through decreasing the exposing probability[5]. Meanwhile, melting point and viscosity of vanadium slag has been greatly influenced by the SiO2 content. Therefore, this work attempts to analyze the above-mentioned questions systematically."

Jan 1, 2012

By Marco Antônio Siqueira Rodrigues

The possibilities for treating rinse waters fiom chromating bath by electrodialysis are discussed together with the possibilities of optimizing the treatment process for waste reduction and reuse of water and chemical products. An industrial effluent with 4600 ppm of Cr(VI), besides other metallic contamination, was used as work solution. This solution has been recirculated on an electrodialysis cell of three compartments, using exchange membranes Selemiom AMT and CMT. A migration of dichromate ions into the anodic compartment was obtained, so that an extraction of circa 99.9 % of Cr(VI) present on the solution was observed, resulting in water with a Cr(V[) concentration of 4 rnd. These results show that electrodialysis can be used to treat these effluents, and this water could be reused as rinse water. The solution of the anodic compartment, consisting at the beginning of the experiment of H2S04, 0.1 N, reached 7200 mg/l of Cr(VI). This concentrate could be reused on the chromating bath itself.

Jan 1, 1999

By N. B. Gray, I. F. Taylor

"Gas injection to promote chemical reactions or mixing is a feature of many metallurgical processes. Often the aim of gas injection is to bring about a chemical reaction between the gas and liquid but most of the past physical and mathematical modelling work has ignored the influence of such reactions. In the work reported here, cold model studies have been conducted in which gas reacts with the liquid into which it was injected. The rate of liquid mixing has been measured as an indication of the mechanical energy transfer. It has been found that gas generated chemically within the liquid is significantly less effective at promoting mixing than the equivalent volume of inert gas. The relative ineffectiveness of chemically produced gas is thought to be due to smaller bubble sizes in comparison to the inert gas case. Small bubbles characteristic of chemically generated gas move with low slip velocities relative to the liquid and lead to different turbulence generation mechanisms.IntroductionIn processes such as steelmaking, copper conversion, bath smelting and ladle steel finishing gas is injected into liquid metal where it reacts chemically or simply serves as a source of agitation. An understanding of fluid flow phenomena in such situations is an essential pre-requisite to the calculation of process intensity and the optimisation of vessel productivity. Traditional physical cold modelling approaches to prediction of liquid flow in such situations are now often augmented by the techniques of computational fluid dynamics. Even with the availability of numerical modelling techniques cold physical models continue to have an important role for validation because it is generally difficult to obtain quantitative data from high temperature processes.Almost all previous cold modelling work has been based on the injection of an inert gas into water or some other non-reactive liquid. Such models do not include the significant increase in gas volume inherent in some processes. For example the oxidation of carbon in steelmaking leads to a twofold increase in molar gas flux through the reaction:"

Jan 1, 1996

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By T. K. Mukherjee, C. K. Gupta

"The importance of the processing of secondary resources such as solid industrial wastes and liquid effluents as well as byroducts for the recovery of the associated metal values hardly needs any elaboration. Such processing contributes in no small measure towards the augmentation of the availability and the supply position of resources. As an added benefit, it leads to a reduction in environmental pollution caused by the undesirable waste materials. As some typical examples of secondary resources in the Indian scenario, mention can be made of spent catalysts, metal/alloy scrap, ash, consumed batteries, flue dust, slag, sludge and slime, pickling solutions, spent acids, plating rinse solutions, spent etchants, waste water from synthetic fibre manufacture and from tanneries etc .. These wastes constitute a source of a variety of non ferrous metals. In the processing of secondary resources like these, the techniques of hydrometallurgy such as solvent extraction playa pivotal role.This paper outlines the efforts made to use solvent extraction to recover (1) base metals such as copper, zinc, nickel and cobalt from a number of secondary resources like cake, and sludge (2) refractory metals like molybdenum and vanadium from sulphidic byproducts and spent catalyst and (3) nuclear metal like uranium from phosphoric acid. In the case of base metals, process flowsheet involving the use of acidic extractants such as DEHPA and PC88A have been optimised. The problem of iron removal from the leach liquor, which influences the metal recovery process significantly, has drawn a special emphasis. In the case of refractory metals, basic extractants like Alarnine 336 has been pressed into service to produce kilogramme quantities of pure salts of molybdenum and vanadium. Finally, the paper gives a brief account of plant experience in recovering uranium from phosphoric acid, using a solvent system comosed of DEHPA and TOPO."

Jan 1, 1996

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By K. Robinson

Following the longest Smelter campaign in BCL?s history it was planned to completely rebuild the flash smelting furnace in 1987. This was the fourth major overhaul and the most extensive so far attempted. Detailed planning took place over several year$ preceding the shutdown and implementation was completed in 54 days. The key to minimising shutdown time was the method designed for installation of the new uptake shaft and reaction shaft. Major repair work was also undertaken in the waste heat boiler and electric furnaces. Both of these activities had an impact on the critical path of the flash smelting furnace overhaul.

Jan 1, 1993

An iridium oxide coated titanium electrode was tested as anode in copper electrowinning. Initial results confmed that the DSA-type anode was significantly more active for oxygen evolution than traditional lead anodes. However, during longer runs, the anode potential was observed to increase linearly at a rate of 220 mV/year. Scanning elecuon microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the anode passivation could be attributed to elecuochemical dissolution of the coating. The effect on the anode potential of organic additives (glue and thiourea) and lead in solution was also examined. A preliminary economic evaluation of the anodes is given.

Jan 1, 1992

By R. C. Nascimento

It was investigated the effect of the addition of bentonite on the physical propertiesof pellets produced from fines of manganese ores. Cold-bonded pellets were produced. Pellets bearing up to 1 wt% of bentonite were submitted to strength compression resistance tests, fatigue of pellets to impact and maximum height of fall tests. A correlation of resistance of the pellets and time for curing were stablished. The produced pellets match the conditions for raw materials used in electric smelting hrnaces to produce manganese based ferro-alloys.

Jan 1, 1995

By Raymond F. Dalton

Despite the ready availability of numerous zinc sources, the process of solvent extraction- electrowinning (SX-EW) has as yet found little favour in the zinc industry. It is suggested that this is largely due to the previous lack of availability of suitable selective reagents having the particular features required to enable them to fit in to a solvent extraction-electrowinning based process for zinc, particularly with regard to strength and selectivity for zinc over iron. This paper describes work on the development of new selective extractants for the recovery of zinc from both sulfate and chloride aqueous solutions and suggests how they might be integrated into new zinc processes.

Jan 1, 1994

By M. Olper

Today, copper production from direct leaching of oxidized copper ores followed by solvent extraction-electrowinning (SX-EW) accounts for about 15% of the total primary world output. SX-EW is a well-accepted process with an operating cost in the range 16-20 cents/lb. copper for small and medium size plants, depending on the plant size and local conditions. However, this technology presents some drawbacks that affect the operating cost and cause environmental concerns. ENGITEC and Paques Bio Systems have developed a new process that avoids the solvent extraction step and operates the copper electrowinning step at a lower cell voltage because of the depassivation of the anodic reaction. The consequence of this new concept is that the direct operating cost is in the range 10-12 cents/lb. copper. This new process is composed of the following steps: ? Selective precipitation of copper from leach solutions by biogenic H2S, yielding CuS and regenerating acid ? Leaching of the CuS with a ferric fluoborate solution to dissolve copper and produce elemental sulphur that is recycled back to the H2S biogeneration step ? Electrowinning of copper fluoborate solution in a diaphragm cell with the ECUPREX® Process, producing copper cathodes and regenerating the ferric fluoborate solution to be recycled back to the leaching step ? Biogeneration of H2S from the elemental: sulphur generated during the leaching step, with the nutrient source for the anaerobic bacteria selected form a wide range of organic substances and/or some industrial by-products containing carbon and hydrogen This paper describes all process steps with particular reference to the biological H2S generation technology. Also discussed' is the capability of the ECUPREX® Process to treat copper sulphide concentrates and copper matte.

Jan 1, 1999

By E. Bélisle, Christopher W. Bale, S. Petersen, C. Robelin, K. Hack, J. Melançon, G. Eriksson, A. D. Pelton, P. Chartrand, S. A. Decterov, I. H. Jung, A. Gheribi

The FactSage® package consists of a series of information, database and calculation modules that enable one to access pure substances and solution databases and perform thermochemical equilibrium calculations. FactSage was originally founded by process pyrometallurgists and has since expanded its applications to include hydrometallurgy, electrometallurgy, corrosion, glass technology, combustion, ceramics, geology, environmental studies, etc. With the various modules one can perform a wide variety of thermochemical calculations and generate tables and graphs of complex chemical equilibria and phase diagrams for multicomponent systems. This paper presents examples of recent and current developments in FactSage in areas of particular interest to Dr. David Robertson. These include both ferrous and non-ferrous processing, as well as solidification and refining simulation. The paper also includes reference to the Internet Fact-Web education package.

Jan 1, 2014

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By F. Baldini, M. S. Borges

"The proposed method emphasizes the optimization of waste management with regard to the exploitation of raw materials incorporated in the remains of industry, as well as the economics of natural resources as an environmental impact assessment. This system [tool] allows: (a) the conversion of an environmental liability into an asset by finding a line of appropriate research for each type of waste and the development of new materials applicable to other industries, (b) the performance of internal control of the waste generated (production, storage, final destination) as well as legal conformity.Objectives:1.1 General objective:To design a collaborative system for socio-environmental management of industrial waste.1.2 Specific objective:Develop evidence of concepts;Evaluate the deployment of the inventory of waste in an industry;Enable the conversion of an environmental liability into an asset by finding a line of research appropriate to the waste: a case study;Evaluate the environmental legislation in the legal mechanisms that influence company decisions.IntroductionThe global economy is undergoing major changes, among these changes; it should be highlighted those related to technological progress and environmental quality.While the industrialized countries and higher levels of economic growth dominate modem technology, developing countries are identified by a different growth pattern, using the annual growth rate of Gross Domestic Product per capita [3, 18].Growth is when the GDP grows, in percent, over the previous year. Development, on the other hand, is when the countries change their technologies and improve their internal structure. Thus, the growth considers the accumulation of wealth, while the development is concerned with the distribution of wealth, improvement of the quality oflife and environmental quality [3, 18].As the UNESCO report shows (1999), the biggest problem is between consumption and development, what is produced and the end that is given to the product. Therefore, product and by-product have equal importance in the quantity produced [29].On one hand there is a positive relationship between indicators of economic growth and technological progress, however, on the other hand, these transformations are a paradox, confirmed by the dramatic use of environmental resources and the lack of technologies for recycling of industrial scrap."

Jan 1, 2011

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By H. Y. Sohn

The ignition and combustion of chalcopyrite particles under suspension-smelting conditions, in which the particle-particle interaction is neglected, has been analyzed by considering the intrinsic kinetics of oxidation and heat and mass transfer between the particle and its surroundings. Reasonable agreement has been obtained between the calculated results and experimental results from a laminar-flow furnace reported in the literature. This computation- al procedure has further been applied to flash-smelting conditions. Under suspension-smelting conditions (Sh = Nu = 2), chalcopyrite particles ignite at around 960 K. The effects of various parameters, such as oxygen concentration, particle size, and gas temperature, have also been evaluated. Comparison between calculated results in this work and experimental observations indicates that SO is the important gaseous product that forms at the surface of the particle.

Jan 1, 1993

By Fuqiang Guo

Scorodite (FeAsO4, 2H2O) is suitable mineral carrier for immobilization of arsenic-rich wastes. Its stability is, however, highly pH dependent (typically at 4 ≤ pH ≤ 7) and satisfactory only under oxic disposal conditions. In thiswork an encapsulation process using mineralized gels of aluminum hydroxy-oxides is developed to enhance the stability of scorodite under wider pH and redox potential range conditions. The encapsulation involves blending and ageing of synthetic scorodite produced by McGill’s atmospheric scorodite process with aluminum hydroxyl gels derived from controlled hydrolysis of aluminum salts. The amorphous hydrolyzed Al-gel encapsulates the scorodite particles,which upon short-term aging transforms into crystalline Al (OH)3/AlOOH mineral phases providing a robust protection microscopic barrier. Long-termstability testing demonstrates the encapsulation systemto be highly effective in suppressing arsenic release under either oxic or anoxic (100 mV < Eh < 600 mV) potential and neutral-alkaline pH (7 ≤ pH ≤ 9) ranges.