Search Documents

By G. St-Amant, V. Cloutier, E. Ghali, S. Jin, G. Houlachi

During the casting of lead-silver anodes, variations in cooling rates result in the formation of an uneven microstructure. The slowly cooled areas (SCA) have a coarser microstructure than that of the remaining part (called "the general zone"). The effect of anode microstructure on the electrochemical behavior was investigated using galvanostatic, potentiodynamic and electrochemical impedance techniques. The results show that the resistances for the two steps of the oxygen evolution reaction on the slowly cooled areas of Pb- Ag anodes are higher than that on the general zone. The double layer capacitance for the first step of the oxygen evolution reaction (OER) and the pseudocapacitance of the second step of OER on SCA are smaller than those on the general zone. The potentiodynamic results show that the amount of lead dioxide formed on the SCA is greater than that of the general zone of the anode. The potential decay curves after 30 minutes of galvanostatic polarization at 45 mA/cm2 show that the corrosion potential of the SCA is 200 mV lower than that of the general zone. This can lead to perforation because of the formation of a galvanic cell with a small anode and a large cathode.

Jan 1, 2000

By Nils Eivind Kamfjord, Mari K. Næss, Halvard Tveit, Edin H. Myrhaug

"As a part of the FUME research programme being done by the Norwegian Ferroalloy Research Association (FFF), the SINTEF Group and NTNU, several measurements towards quantifying the gaseous and solid emissions from the draining of the silicon furnaces for metal have been carried out.Based on the measured size distribution of the formed fume particles and known particle growth theory, an estimate of the growth time for the given particles has been calculated. The formation time for the measured NO amount has also been calculated based on the fume measurements and a thermodynamic model of the furnace gases combusting with air. The two “formation” times are in the same order of magnitude and they are therefore used as parameters in a CFD model, modelling that the formed fume particles are heating up the surrounding air and thereby forming NO according to the Zeldovich mechanism. The measurements show an approximately equal constant NO formation per fume particle. The CFD model shows results in the same order of magnitude, supporting that the particle growth and NO formation happen under near stoichiometric conditions and are controlled by the formation of SiO2 fume.IntroductionNOx is the common notion for the two gases nitric oxide (NO) and nitrogen dioxide (NO2) formed during combustion of fuels. The main sources for human made NOx emissions is on-/offshore transportation industry, power generations based on fossil fuels, agriculture and other industries [1]."

Jan 1, 2012

"Recycling of solid wastes plays an important role in environmental protection. However, solid wastes are often contaminated with some undesired components so that many of these solid wastes are hardly economically recycled. Therefore, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes. There exist three general strategies of separation of undesired components from solid wastes: before-process separation, post-process separation and in-process separation. In this paper, different separation strategies are discussed in terms of energy requirement and availability, implementation complexity and additional need for environmental protection. It is concluded that of all separation strategies, in-process separation has the least energy requirement, the least implementation complexity and the minimum need for additional environmental protection.IntroductionIn industries, solid wastes almost come with every production process. Multi-million tons, if not billion tons, of solid wastes are being generated globally each year. These solid wastes are lowvalue materials in general, and often have very limited markets. As a matter of fact, many of these solid wastes have been stored on site or have been disposed of at landfills for many years, not only occupying lands, but also polluting environment. Therefore, effective and efficient recycling of solid wastes has been a very challengeable task and has played a very important role in environmental protection.One of the major barriers which hinder recycling of solid wastes is contamination of the solid wastes with some undesired components. These undesired components are components which are not wanted by production processes or applications where the solid wastes are consumed or recycled, since the undesired components often degrade qualities of the solid wastes, imposing negative effects on operations, facilities and product qualities of the production processes or applications. Sometimes, the undesired components may also pose severe environmental concerns. When undesired components are present in solid wastes at over-limit levels, the solid wastes tum to become destructive, useless and non-recyclable. Consequently, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes."

Jan 1, 2014

By N. Ono, H. Fujiwara, S. Otsuka-Yao-Matsuo, T. Omata

"The electrical conductivity and the oxygen release and uptake of sintered indium tin oxide (ITO) upon heating and cooling under the condition that P(O2)/P*=4.9X10-4 (P* = atmospheric pressure), :when P(O2) was approximately 50Pa, were simultaneously measured by using a closed-system oxygen-gas analyzer. A large increasing in -the electrical conductivity - upon the· oxygen release detected in 1130<T<1273K was observed. Quantitative relationship between the number of oxygen atom released from ITO and the conduction electron density in ITO was studied. The release of one oxygen atom agreed with the generation of two conduction electrons, i.e., the efficiency-carrier-generation for the oxygen release from the ITO was almost one. The oxygen atom released must be originally at the quasi-anion site in the C-type rare-earth lattice, i.e., the 16c site in the space group of Ia3, as an interstitial excess oxygen, Oi"". It was concluded that the mechanism of conduction carrier generation and compensation upon SnO2 doping into In2O3 can be expressed by the defect equation, 2SnO2-2Sn1n +2(1-z)e'+zOi""+3O0 x+(l-z)/2O2, and that the oxygen release bringing the increase in the electrical · conductivity can be expressed by the equation, Oi""-1/2O2+2e'.IntroductionThin films of SnO2-doped In2O 3 (generally designated as ITO, for indium tin oxide), which have high optical transparency for visible light and high electrical conductivity, have been used as transparent electrodes for liquid crystal and electrochromic displays. It is well known that the electrical conductivity of ITO depends on the content of SnOi-dopant and oxygen. However, a reliable relationship between electrical conductivity and the absolute oxygen content in ITO has yet to be reported. The elucidation of such a relationship is one of the important clues for realizing extremely highly conductive ITO electrodes."

Jan 1, 2000

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015

By K. E. Gonsalves, G. M. Chow

"Nanostructured powders (particle diameter of 1 - 100 nm) have uses in electronic, magnetic, structural, thermal applications as well as advanced processing of materials. Among many methods of making nanostructured powders, chemical routes offer many attractive features such as feasibility of cost-effective bulk quantity production, design of chemistry at the molecular scale, and chemical homogeneity of the powders. In this talk, two systems of chemically synthesized nanocomposite powders are presented, namely, granular magnetic materials of Fe-Cu and Co-Cu, and thermal-structural materials of AIN-BN. Synthesis and processing, characterization and properties of these materials are discussed.IntroductionNanostructured powders (particle diameter of 1 - 100 nm) are attractive materials because of many useful properties (e.g. catalytic, optical, magnetic etc.) and processing advantages (e.g. lower sintering temperature) [1]. There are many methods of making nanostructured powders, for example, physical and chemical vapor deposition, mechanical attrition, and solution chemistry [1, 2]. A common method of making composite powders involves the grinding, mixing and blending of constituents powders, but it has the limitation of inhomogeneous mixing. Chemical routes have many useful features. Using solution chemistry, precursors can be molecularly tailored and homogeneously mixed at the molecular level. The chemical approach may result in better properties of the final product. Compared to vapor-phase fabrication techniques, chemical routes are more cost-effective in producing large quantity of material. In addition, control of particle size, size distribution and stabilization of the nanoscale particles against agglomeration can be more effectively manipulated via solution chemistry.In this paper, we present an overview of some of our work in nanocomposite powders prepared by solution chemistry. Metallic systems of FeCu and Co-Cu, and ceramic system of AIN-BN are discussed. The powders were characterized using x-ray diffraction (XRD) , scanning electron microscopy (SEM), conventional and high resolution transmission electron microscopy (TEM, HRTEM), vibrating sample magnetometry (VSM), inductively coupled plasmaatomic emission spectroscopy (ICP-AES)."

Jan 1, 1994

By Paul O. Malan

"The Tusc gold deposit is located along the Carlin Trend approximately 13 kilometers north of Carlin, Nevada and 2.5 kilometers northwest of the Gold Quarry mine. Tusc is one of several structurally controlled oxide gold deposits located along the Good Hope fault within the Maggie Creek subdistrict. Mining commenced in 1994 with an oxide reserve of780,000 troy ounces of gold at an average grade of 1.34 g/t Au. The Good Hope fault forms the southwestern edge of the Schroeder Mountain uplift (also known as the Carlin Window) and juxtaposes carbonate rocks of the Siluro-Devonian Roberts Mountains Formation against siliceous mudstone, siltstone, and silty limestone of the Devonian Rodeo Creek unit. Submicroscopic gold mineralization is disseminated in the Good Hope fault system and in fractured hanging wall carbonate rocks. Wallrock alteration includes silicification, deca!cification, sericitization, and late alunite replacement and veins. All Tusc ore is transported 2.5 kilometers to Gold Quarry for processing. Leach-grade ore (0.2 - 1.7 g/t gold) is placed on the oxide leach pads, and mill-grade ore(> 1.7 g/t gold) is processed through the CIL oxide mill. IntroductionThe Tusc gold deposit is located in Eureka County, Nevada, U.S. A, approximately 13 kilometers north of the town of Carlin and 2.5 kilometers northwest of the Gold Quarry mine (Fig. 1 ). Tusc is one of several open-pit, oxide, gold deposits within the Maggie Creek subdistrict of the Carlin Trend. Tusc is a structurally controlled gold deposit located along the Good Hope fault. Submicroscopic gold mineralization is disseminated in the brecciated and silicified Good Hope fault zone and along intersecting northeast and northwest striking structures."

Jan 1, 1997

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012

By P. A. Manohar

This paper describes an implementation of the Potts model for simulation of grain growth in 2D on a distributed-memory parallel architecture. The simulation scheme utilizes a continuous-time, asynchronous parallel version of the n-fold way algorithm. Each Processing Element (PE) carries a piece of the global simulation domain while the virtual topology of the PEs is in the form of a square grid in 2D and Torus in 3D. Different PEs have different local simulated times. Inter-processor communication is carried by the Message Passing Interface (MPI) routines. Sample results for grain growth simulation in 2D are presented for a 840 x 840 global domain size distributed over 16 PEs. The grain growth kinetics obtained in the simulation of pure, isotropic systems is in good agreement with the theory. Grain size distributions obtained in the parallel simulation are well described by the lognormal distribution, thus validating the simulation procedure. Keywords: Metropolis algorithm. n-fold way algorithm, asynchronous parallelization, grain growth

Jan 1, 2003

By K. R. Robilliard

An outline is given of the problems facing tlile lead and zinc industry from the viewpoint of the range of residues currently produced from electrolytic zinc, blast furnace and other processes. Smelting approaches available using top submerged lancing technology are discussed and analysed. Pilot plant results for a range of lead and zinc-bearing materials are presented.

Jan 1, 1992

By P. Felix

A discussion on the need of visualization and animation tools in modelling solidification processes is made. An outline of an approach for the production of a video computer animation is provided. A number of examples including, 2 and 3 dimensional melting, filling, and macrosegregation are presented.

Jan 1, 1993

By Tomás Vargas

The catalytic influence of a pure strain of Thiobacillus ferrooxidans (ATCC 19859) on the dissolution of natural pyrite crystals was studied using electrochemical techniques. The results showed that this microorganism catalyze the leaching of pyrite by both, oxidizing ferrous iron in solution and depolarizing the reduction of ferric ion on this sulfide. In addition, studies of bacterial corrosion under applied potential showed that pitting on the pyrite surface centers on weak sites of the sulfide structure in which bacteria has attached, but occurs only when the ferric iron in solution induces an adequate level of anodic polarization on the mineral.

Jan 1, 1992

By Guangchun Yao, Chuan Li, Hongjie Luo, Zhuokun Cao

"The expansion rate and collapse time of liquid aluminum foams are essential for the determination of operating time and quality of the resulting foam. In the present paper, liquid aluminum foams was fabricated by adding in TiH2 as blowing agent, and the variation of expansion rate with foaming time was non-contact detected by a laser distance measurer. The influence of different stabilizing agent and alloying elements was studied. The results show the fact that the fraction of stabilizing agent only perform little effects on the maximum expansion rate of liquid aluminum foams, while the influence of alloy elements are remarkable. The maximum expansion rate would increase much when Mg is added, and the liquid foam also collapse at a shorter time. Comparison was made between experimental results and mathematic calculations, which reveal the fact that it is the change of TiH2 decomposition responsible for the change.IntroductionMetal foams, combining light weight with other unique mechanical and physical properties, have gained wide interest and been developing fast during past few decades. However, manufacture of this new material is quite challenging since it involves simultaneous occurrence of gas, liquid and solid phase at high temperature [1-2].Quite some manufacture routes have been developed for manufacturing metal foams, and the structure and quality of resulting foam are remarkably improved during the last decades. However, most of the past works seems to be experiential, and because the lack of basic knowledge of foaming process, the start material is limited and the production technologies are far from reliable and reproducible.[3-4]In direct foaming process, decomposition of blowing agents, TiH2 for example, is the main force for foam expansion. The density and foam structure changes with time during the foaming process, so it is expected that foams of certain structure can be obtained by solidification of the liquid foam at a certain time [5-6]. However, the foaming process is weak in reproducibility and the influence of stabilization additives and alloying elements is unclear."

Jan 1, 2011

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By J. B. Cocanour

Pioneering work at the U.S. Bureau of Mines (USBM) has produced a personal computer (PC)-based, software-driven video photometric color sensor for real time process control of metallurgical streams. The video photometer is an inexpensive optical sensor which operates in the visual area of the electromagnetic spectrum and collects color information through plastic optical fiber. The red, green, and blue (R/G/B) voltage components of the color video signal are digitized and characterized through software and then presented as the control variable for software-based proportional-integral-differential (PID) control. This sensor has been successfully employed in the control of a laboratory copper electrolytic circuit. With this sensor, copper solutions were analyzed on-line without the need for sample removal, dilution, mixing or reagent addition, thereby allowing for the real time control of the circuit.

Jan 1, 1994

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By Gunnar Eriksson

Computer simulation has become an everyday practice in thennodynamic and materials research. Advanced thennochemical algorithms take into account heat transfer effects and salient reaction kinetics when applied for process models. In particular, the combination of mass transfer or overall reaction rates with multi-component Gibbs energy minimisation provides an effective tool for simulation of industrial thennochemical processes and processing of materials. In this work the combination of rate factors with the Gibbs energy technique was studied by using the novel program ChemSheet, which operates through Microsoft&apos;s Excel® spreadsheets. Such processes as, for example, CVD of pure silicon production, titania pigment manufacturing, vapour pressure of Mercury in amalgams (in Hg-Iamp manufacturing) and melting behaviour of low-temperature alloys have been modelled. Provided that the thennochemical data is available simulations can be performed with any thennodynamic system. The calculation can be performed as an affinity study without a particular reactor model or with a specific reactor scheme.

Jan 1, 2001

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994