Search Documents

By J. Huot

It has been shown that magnesium-based metal hydrides such as Mg2Ni could be synthesized by high energy mechanical alloying. This process creates a nanocrystalline alloy that has enhanced hydrogen sorption properties due to the high density of defects and grain boundaries. Unfortunately, this process also requires a long synthesis time (up to 100 hours in some cases). In order lo reduce processing time and cost of synthesis, we have investigated the effect of milling at elevated temperature under an inert atmosphere. Milling at high temperature improves interdiffusion of the elements and reduces the number of structural defects such as vacancies, dislocations and internal strain. It was found that by milling elemental powders at 200°C. a complete synthesis of Mg2Ni could be achieved in 8 hours. This synthesis time is roughly an order of magnitude lower than that of the process conducted at room temperature. The hydrogen sorption kinetics and capacity of this material are comparable to Mg2Ni synthesized at room temperature.

Jan 1, 2002

By Min Chen, Lei Xu, Liang-yu Jin, Xue-liang Yin

For the purpose to reduce the high cost and heat storage loss of Al2O3-MgO bricks used as ladle linings, Al2O3-MgO-CaO bricks with lower theoretical density were fabricated and the densification behavior as well as mechanical property of this refractory was investigated. With addition of CaO, the initial sintering temperature of Al2O3-MgO refractory was decreased from 1300 to 1100°C associated with the expansive formation of CA2, and the compressive strength was also enhanced owing to the formation of bond linkage between CA6 and spinel. At high temperature, brick with 4% CaO content showed poor sinterability with high porosity because of the formation of platelet structure of CA6 grains, whereas brick with 8% CaO content was well sintered with higher relative density but lower bulk density than Al2O3-MgO brick, indicating that the densification as well as lightweight of Al2O3-MgO refractory was effectively promoted.

Jan 1, 2015

By W. G. Davenport

All Outokumpu flash furnaces burn some hydrocarbon fuel. Hydrocarbon combustion supplements heat from Fe and S oxidation and provides local heating in cool; parts of the furnace. Adjustment of hydrocarbon fuel combustion rate is an effective way of controlling furnace temperature. More oxygen and more oxidation of Fe?and S in the flash furnace continue to diminish the need for1hydrocarbon fuel. Still, as Tables 2.1 and 3.1 show, all flash furnaces use it. Oil is the most common fuel -natural gas, coal and coke are also used. This chapter demonstrates how hydrocarbon fuel is included in our flash furnace matrix. It shows that: (a) three new variables, mass hydrocarbonfoel. mass CO2 in offgas and mass H2O in offgas are inserted (b) carbon and hydrogen balances are added (c) hydrocarbon fuel quantity is specified (d) ,the oxygen balance is modified to include CO2 and H2O (e) the enthalpy balance is modified to include hydrocarbon fuel, CO2 and H20.

Jan 1, 2001

By Susumu Okabe

The Mitsubishi Continuous Copper Smelting/Converting Process employs an electric furnace for settling the slag/matte mixture formed in the smelting furnace. In order to improve the separation of slag and matte and to minimize power consumption, the design and the operating conditions of the electric furnace should be optimized. As the first step, numerical heat and fluid flow analysis of the melts was carried out based on the distribution of current density and Joule?'s heat obtained by the electric field calculation. For these calculations, 3-D body fitted coordinate system and a finite volume method were applied. Using the developed numerical model, the flow pattern analysis by pulse input of a tracer element was simulated. It was found that a strong thermal convection of the molten slag exists around the electrodes due to the concentrated Joule's heat generation in a small area just under the electrodes, and this strongly affects the flow pattern in the furnace. The calculation results were compared with the data obtained from 'a plant test.

Jan 1, 1998

By John Frederick Colloghon, O&apos

Bulong remains the only hydrometallurgical process plant in the world that recovers nickel and cobalt directly from high pressure acid leach (HPAL) laterite leach liquors without need for precipitation of an intermediate product (e.g. sulphide, hydroxide or carbonate). Direct solvent extraction (DSX) of both nickel and cobalt in combination with electrowinning of nickel has been operation at Bulong since early 1999. Focus in the first years has been on ramp-up and resolution of commissioning problems. More recently the focus has been on de-bottlenecking and process optimisation. A number of significant process problems have been resolved, the most difficult being the formation of gypsum in the nickel solvent extraction circuit. Sound control of process chemistry is essential to ensure the production of high quality nickel and cobalt products at the lowest possible cost. This paper describes the numerous changes and enhancements to the process chemistry and plant equipment at Bulong and discusses the importance of ore leach chemistry on downstream impurity metal removal. Potential additional enhancements to further reduce unit costs are also presented.

Jan 1, 2004

By Ian Masters, Saul B. Davies, David T. Gethin

The purpose of this model is to simulate and analyze the energy flows within a rotary aluminum recycling furnace, using the global properties of its main components, the gas, metal and refractory walls. The model will simulate a series of operations such as loading, heating and stirring which will constitute the processing of a batch. Each main component of the furnace is treated as a one-dimensional heat transfer medium, the thickness and area of each medium being calculated from the actual geometry of the furnace. The physical properties are taken as the weighted average of those for the various layers forming the medium. Incorporated into the model are elements describing the radiative exchange within the furnace, melting of the charge, and forced convection in the melt due to the rotation of the furnace. This approach has produced a model with a reasonable computing time that can be used to run a whole series of simulations for the prediction and comparison of the furnace performance under different operating conditions.

Jan 1, 2000

By Yu. A. Grinin, Yu. A. Sannikov, M. A. Lyamina, V. A. Shumskij, L. V. Slobodkin, N. N. Ushakov

This manuscript describes the Kivcet treatment of lead-bearing materials having high contents of copper and zinc. The tests were carried out on bulk concentrates from the Zyrianovsk Mining and Concentrating complex, "Kazzinc" JSC (Kazakhstan) with the following composition: Pb 37.6%, Cu 10.4% and Zn 6.8%. Two properties of the concentrate were under investigation: their calorific value and their desulphurization rate. By adding flux, the charge properties were brought close to the properties of high-grade lead sulphide concentrate. The charge was melted with high productivity. To ensure high copper recovery, Waelz residue was added to the charge. The residue contained more than 20% carbon and about 30% iron metal. The residue was partially replaced by coke that facilitates high copper recovery into the matte. The smelting achieved a production rate of 20 t/h with one burner. Lead recovery into the lead bullion was 88.8%; copper recovery into matte was 92.3%; zinc recovery into slag was 75.5%; and zinc recovery into the fume was 5.1%.

Jan 1, 2000

By Brady Butler

Many high capacity metal hydrides exhibit a high degree of stability in the hydrogenated state. This stability leads to a number of significant design problems with regard to the low temperature kinetics and thermodynamics of dehydrogenation. Nanometric metal hydride materials provide a promising route for increasing the reaction kinetics while altering the thermodynamic stability of the material. The use of nanometric metal hydride materials for hydrogen storage has largely been absent because of the difficulties associated with the synthesis of these materials. In this paper, research results on the synthesis of lithium based metal hydrides by vapor phase reactions are presented. The lithium based compounds that have been made in our lab include nanosized powders of metallic Li, Li₃N, LiNH₂ and LiH. The vapor phase process has also been used to custom engineer Li-based materials with other alloying elements or doping elements. The dependence of the characteristics of these materials on synthesis process parameters is studied. The effects of nanoscaled particle sizes on the kinetics of dehydrogenation and hydrogenation reactions are also explored.

Jan 1, 2006

By Scott Shuey

The processing of post-consumer materials is an area being addressed by many industries and multiple engineering disciplines. While metal scrap and high-value uniform waste streams tend to find their way back to their respective parent processes, the more complex and low-cost ubiquitous materials, such as Polyvinalchloride (PVC) and Polytetrafluorethane (PTFE), tend to show up in many processing streams. From a metallurgical perspective, pyrometallurgical processing of a mixed metal/organic/oxide waste material allows for the recovery of thermal energy in conjunction with the recovery of metal values. The evolution of halogenic acids during elevated temperature processing can create complications with both the materials of construction of the processing equipment as well as gas stream processing. The need for dust collection coupled with a high acid content, necessitation high-volume scrubbing, increases the costs associated with gas handling. Control of the halides through entrapment as a solid in-situ during processing would simplify downstream processing. Alkali-halide complexes are being evaluated by researchers at CSM for mixed metal/polymer waste material treatment, recovering halogens as salt complexes.

Jan 1, 2006

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By Vinay Kumar, Jae-Chun Lee, Rakesh Kumar, Manis Kumar Jha, Archana Kumari, Pankaj Choubey

Present work is a part of developing novel recycling technique for waste printed circuit boards (PCBs) i.e. the liberation of metals from PCBs by organic swelling followed by the treatment of resin to remove/ recover hazardous soldering materials. In order to recover the hazardous metallic constituent lead from the liberated resin, initially the leaching studies were made using fresh solder containing 63.9% Pb and remaining tin. Experimental results obtained in different conditions viz. time, temperature and acidity showed -97.20% of lead dissolution with 6M HNO3 at solid to liquid (S:L) ratio 1:10 (g/mL) and temperature 90°C in 75 minutes. The result of the studies validated with crushed PCBs shows that almost total lead and tin was leached out with 6M HNO3 and 6M HC1 respectively at S:L ratio 1:10 (g/mL) and temperature 90°C within 50 minutes. The results will be useful for the treatment and safe disposal of PCBs resin.

Jan 1, 2011

By Jin Liu

In the early 1990?s, Inco successfully installed two new flash furnaces as part of their SO2abatement project to reduce SO2 emissions from the Copper Cliff Smelter by 60%. The flash furnace off-gas is cooled and cleaned through two new Monsanto Dynawave gas cleaning systems that replaced the traditional venturi scrubbing system. It was discovered that the flash furnace production capacity is often limited by the capacity of the gas cleaning system. The key task is to eliminate pressure drop from the system. The froth column is responsible for by far the largest pressure drop in the gas cleaning system. Initially, the column was fitted with 22 plates. In 1994, both #1 and #2 froth columns were modified by reducing the number of plates in each column from 22 to 18 and increasing the interplate spacing on lower plates. With increasing demand for more throughput in the flash furnaces, further modifications on the froth columns were made in 2005. This paper describes these modifications and results together with some fundamental analysis of the froth column characteristics.

Jan 1, 2006

By D. J. Sellmyer

This paper is Intended to review recent developments in the application of rare earth-transition metal alloys as high density, rewritable data-storage media. First generation magneto-optic media are based on amorphous Tb-FeCo or GdTb-Fe alloys which are adequate but could use improvements In certain respects. A very difficult materials-design problem is encountered because of the following requirements: a sufficiently large Intrinsic uniaxial anisotropy, a Curie temperature in the range 100-300°C, a sufficiently high coercivity, a sufficiently high optical absorption, a high Kerr rotation, reflectivity and high carrier-to-noise ratio, a high storage density, a very fine and homogeneous nanostructure, long-term stability, and inexpensive production. , Fundamental issues such as the relationships between the nanostructure and perpendicular magnetic anisotropy, and electronic structure and Kerr rotation are discussed. Attempts to tailor the properties by rare-earth alloying and by preparing compositionally-modulated, nanostructured multilayers are outlined. Challenges and opportunities in competitive materials such as garnets, ferrites and Co/Pt multilayers are briefly discussed.

Jan 1, 1992

By G. Achurra

The products of the smelting of copper concentrates in an El Teniente Converter (CT) are a high grade matte, analyzing 74-76% Cu; and a highly oxidized slag, typically containing 15-20% Fe3O4 and 4-10% Cu. The El Teniente Division of CODELCO¬CHILE has developed a slag reduction-cleaning process, that is practised in a tilting, horizontal furnace, to recover copper from these slags. The El Teniente slag cleaning process has been successfully implemented at the El Teniente Caletones smelter and various other smelters in Chile: Today, eight such slag cleaning furnaces, each with a capacity of 800-1000 tonnes/day, are in operation in Chile. This paper discusses basic laboratory research and industrial tests that led to substantial reductions in the slag cleaning cycle time and the specific consumption of fuel and reductants. Simultaneously, the slag cleaning off-gas quality was improved. Based on the experimental results, recommendations were made to improve the practice of the El Teniente slag cleaning process. The recommended modifications have been fully implemented at the Caletones smelter.

Jan 1, 1999

By L. B. Tsymbulov

At present data on thermodynamic properties of metallic melts, containing copper and ?iron family? metals, is rather limited. Determination of the activity of metallic melts components under high temperature by experimental methods requires high level of labour inputs. With this it is not always possible to obtain the results with high level of accuracy. Due to that in a number of cases it is more appropriate to apply different methods of analysis, with the help of which there can be calculated thermodynamic properties of ternary and even more complicated systems, prominent thermodynamic properties of binary systems being used as a basis for these calculations. This work presents the results of calculations of different components activity and activity ratio in such ternary system melts as Ni-Cu-Fe, Ni-Cu-Co, Fe-Cu-Co and Fe-Co-Ni. Good compliance of calculations results with those obtained in the course of reliable experimental investigations fulfilment is demonstrated. There are presented the results of activity and activity ration analysis for some compositions of Cu-Ni-Co-Fe system.

Jan 1, 2006

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By Kwan Soo Han

A thermodynamic model for predicting the distribution coefficients has been developed by taking into account the extraction mech-.ism and the chloride complexation when Sm, Eu, Gd, Tb, Dy and Ho for single component systems are extracted from acidic chloride solutions by di-2-ethylhexyl phosphoric acid and 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester in kerosene, respectively. The model equation includes two constants, of which one corresponds to the apparent extraction equilibrium constant and the other is due to the variation of the activity coefficients of organic species. These values are determined from a few experimental data by the curve fitting method Then, the distribution coefficients under untried conditions have been predicted from only the initial data by iterative calculations. Bromley&apos;s formulation is used to estimate the activity coefficients of aqueous species and the interaction parameters for some rare earth chlorides are reported in terms of molality and molarity using data from Spedding et al. The validity of this method has been confirmed by excellent agreement between the experimental and the predicted distribution coefficients.

Jan 1, 1989

By Bruce W. Downing

MagPower has developed methods to control the detrimental formation of hydrogen that occurs in electrochemical reactions in numerous commercial applications such as the Magnesium-Air Fuel Cell, electrowinning, zinc alkaline batteries, hydrogen embrittlement, waste water/ metal recycling and coolants. The company?s approach to an alternative energy source is the development of an environmentally friendly non-toxic alternative power source that generates electricity through a combination of magnesium, oxygen and a saltwater electrolyte with MagPower?s patent pending hydrogen inhibitors. The magnesium-air technology has never reached the commercial stage due to its limiting power output caused by hydrogen generation. MagPowerhas solved this problem and has patents pending on its intellectual property; the Hydrogen Inhibitors and has developed several consumer power units for a variety of applications through licensing agreements. The company has also shown that the inhibitors have an impact on zinc electrowinning through laboratory test work where current efficiency was improved. This will significantly reduce power consumption and increase the efficiency of the electrowinning process, as well as reduce the potential acid mist hazards associated with electrowinning.

Jan 1, 2003

By D. C. Cupertino

Oxime based solvent extraction provides the user with a selective concentration process for copper prior to electrowinning. The selectivity required is largely for copper(II) over iron(III) and this is achieved by the preferential formation of the square planar copper-oxime complex in the organic phase. The copper/iron selectivity of oximes can however, be altered by modifiers or other types of oximes and may be enhanced in the presence of certain esters. Whilst the oxime based SX processes is important for operations leaching copper from laterite ores, the high selectivity will also be significant in processing streams arising from other leaching regimes which are currently under development, for example leaching of sulfide mineral ores. This paper presents some initial results using Molecular Modelling techniques to further our understanding of the nature of the copper/iron-oxime complexation processes together with some plant studies undertaken at a number of different mine sites investigating selectivity, and other properties, for some modified reagents. Some studies of the interfacial properties of the these systems are reported to explain in part the practical observations.

Jan 1, 1999

By Johan Sundström

Anhydrous DyC13 was prepared by dehydration of DyCl3?6H20 in a fluidized bed using both batch- wise and continuous feeding. A gas mixture with varied composition of argon and HCl was used. The productivity was high, reaching values of 0.25 mol H20/m2-st during the reaction step 6- 1 and 0.062 mol H2O/m2.s during the reaction step 1-0. The product was free from hydrolytic compounds, such as DyOCI, if control of inlet gas composition versus temperature was achieved. From the results of various experiments, some relations between HCI-concentration and temperature in order to avoid hydrolysis have been deduced. The fluidization process efficiency decreases drastically after the dehydration has proceeded down to about 10 mol% of remaining water. Therefore, in a final treatment the last traces of water were removed by slowly purging gas through a packed bed. The water content could thereby be reduced to less than 1 mol%.

Jan 1, 1997