Search Documents

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By Jimsher Aneli

The investigation of some peculiarities of conductivity dependence on filler type and amount in the polymer composites has been conducted. It is established, that conductivity of composites based on phenolformaldehide resin essentially depends on proportion of double fillers: graphite + carbon black, graphite+ andesite, contained in composites. It was shown, that these composites characterized by synergetic effect ? non additive influence of fillers concentration on the conductivity of composites. Some other properties of composites contained binary fillers (effect of temperature and pressure on the conductivity) have been investigated.

Jan 1, 2006

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Minjun Tang, Jianfeng Zhou, Linjiang Qing, Yufeng Guo, Tao Jiang

"For the comprehensive recovery ofV, Ti, Fe in vanadium-titanium magnetite in the process of pre-reduction-electric furnace smelting, it is expected that vanadium oxide is reduced into molten iron and titanium oxide is available in the slag. Thus the effect of slag basicity, the content of MgO, MnO and CaF 2 of slag content on the separation of slag and molten iron and the comprehensive recovery of V, Ti, Fe were investigated. The results show that increasing slag basicity, MgO, MnO and CaF2 are all beneficial to the separation of slag and molten iron. Higher slag basicity and the addition of CaF2 strengthen the reduction of vanadium oxide, and inhibite the reduction of titanium oxide, which are in favour of the recovery ofV and Ti. However, the addition ofMgO, MnO was not efficient for the comprehensive recovery ofV, Ti, Fe. For the vanadium-titanium magnetite of Panxi in China, the recovery of Fe was over 98%, the recovery ofV in molten iron was over 85% and the Ti02 content in slag was about 43% under the optimal conditions of slag phase type.IntroductionIt is well known that there are abundant vanadium-titanium magnetite resources which are located in Panzhihua of Sichuan Province[!]. At present the vananium-titanium magnetite concentrates are smelted in the blast furnace, which just make use of iron and vanadium, but lots of titanium is discarded in the slag. At the same time, the process has a large number of disadvantages, such as low recovery of vanadium, long route, pollutions, large investment and expenditure of energy[2-3]. In recent years, in order to efficiently utilize the vanadium-titanium magnetite concentrates, several new non-blast furnace processes have been proposed, such as pre-reduction-electric furnace, pre-reduction-grinding separation and so on[4]. Especially pre-reduction-electric furnace is operating well in South Africa and New Zealand,However,Du to the high slag basicity of the slag, the grade ofTi02 of slag is Corresponding author:Minjun Tang.E-mail:450435123@qq.com. Tel:13627429224."

Jan 1, 2013

By Mark C. Bronson

The feasibility of several pyrochemical approaches-for separating non-radioactive constituents from ICPP HLW calcine were examined. The removal of aluminum as AICI3 from aluminia calcine was successfully demonstrated. The examination of pyrochemical processes to remove non-radioactive constituents, primarily aluminium, zirconium, calcium and fluorine, from zirconia calcine showed that fluorine removal was required in order to chlorinate the calcine. A molten calcium chloride wash, a calcium reduction, and. a sulfuric acid treatment were examined as possible zirconia calcine pretreatment options for fluorine removal. Fluorine removal from simulated ICPP zirconia calcine was demonstrated by both a CaCl2 wash method and a sulfuric acid treatment method. X-ray fluorescence analysis indicated that greater than 97% of the fluorine can be removed by either method. Fluorine removal by a calcium reduction using an alloying agent, zinc, or a calcium reduction using, a filtration separation were also demonstrated, but the efficiencies of fluorine removal were considerably less ranging from 50 to 90%. Regeneration of CaCl2 from the salt and oxide residues of the CaCl2 wash experiments was also demonstrated 'by an aqueous dissolution method. From the salt residue, 85% or more of the CaCl2 was recovered and contained little if any CaF2 or CaO. From the oxide residue close to 100% of the CaC12 was recovered. Because of the overall success of the CaCI2 wash, it was determined to be the preferred fluorine removal process. The sulfuric acid treatment to remove fluorine is effective, but the proposed overall flowsheet has not' been adequately demonstrated.

Jan 1, 1995

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By P. Barrios

The copper refinery of Atlantic Copper was modernised and converted to the Isa permanent cathode system in 1995. The technology installed has proved to be an excellent platform for the development of operational improvements. During the years it has been working, the progressive assimilation of the new technology has been achieved and the level of operator knowledge has allowed design production to be reached and surpassed by more than 10%. At the same time, modifications to the work programmes, using existing equipment, have permitted the incorporation of new cells and the achievement of annual production levels of 250,000 tonnes and a productivity of 0.43 t/man-hour.

Jan 1, 1999

By Keith Axler

The high reactivity of plutonium metal presents safety concerns related to material containment during fire scenarios. Plutonium metal is liquid at temperatures achieved under selected fire scenarios. The appearance of liquid plutonium challenges the corrosion resistance of the containment materials. However, by the in situ formation of intermetallic compounds, the plutonium metal can be stabilized as solid and the integrity of the containment vessels preserved. Studies have been conducted to demonstrate candidate materials, including lead, which can be introduced to the liquid-plutonium system and bind the corrosive liquid metal through the formation of intermetallic phases. The results of these investigations will be presented along with a discussion of the experimentally determined phase behavior for the plutonium-lead system.

Jan 1, 1995

By Viktor Ashikhin, Pavel Arkhipov, Yurii Zaikov

"Lead alloys electro-winning from chloride melts was under investigation. Impurities concentration in cathode lead is strongly depended on temperature, electrolyte composition, anode current density. The equilibrium electrode potentials of lead-antimony alloys with the various content of electropositive metal in the alloy were investigated in the wide temperature interval. Thermodynamic properties of Pb-Sb alloys containing 20-95 mol% of Pb were studied by EMF method in temperature interval 723-873K in molten mixture of potassium and lead chlorides. Partial and integral thermodynamic characteristics were calculated. Small negative deviations from Raul’s law were found. Anode processes were investigated. The lead dissolution was found to be the only process in certain interval of current densities and electropositive metal content in alloy.IntroductionAt present human race is facing the problem of pollution by lead and its compounds and also the pollution influence on population health all over the world. One of the solution ways is the recycling lead containing technical wastes by ecologically clean technologies.World scientific community pays much attention to the electrolysis of molten salts. The usage of salt mixtures, as electrolytes, discovers new possibilities in the production of metals, metal compounds and alloys. ?????????? of the electrolysis at the temperature 50 - 200 °? above the melting temperature of chosen salt mixture allow to unbreaks processes, that undergo in the pre-electrode layer. The rate of the electrodepositing of elements are much higher than in the water electrolytes. At present there are technologies developed for production of metals (Ta, Nb, Ti, Zr, Hf, Ca, Al, Mg, Be, Li and others) by the electrolysis of the melts. Electrolysis of melts might be used in order to convert different technological formations containing lead and other nonferrous metals, that produced by different enterprises. According to the level of the influence on the living organisms lead is in the group of highly dangerous substances alongside with arsenic, cadmium, mercury, selenium, zinc, etc. Toxity and ability to accumulate in the human organism are two main sources of danger for the human being."

Jan 1, 2008

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By John E. Dutrizac, Tzong T. Chen

"Laboratory experiments were undertaken to ascertain the behaviour of various ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C and in the presence of 40 or 50 g/L of hematite seed. Copper, nickel and zinc are not significantly incorporated in hematite precipitates. Although the nickel contents increase to 0.22% as the Ni concentration increases to 60 g/L, the solid solution Ni contents are low relative to the bulk Ni contents. Thus, part of the Ni may be present as tiny particles of poorly soluble NiS04.H20. Increasing germanium concentrations to 2,000 mg/L result in products containing up to 0.59% Ge. The Ge occurs either in solid solution in the hematite or is adsorbed on the nanometer-size hematite crystallites. Increasing As(V) concentrations to 10 g/L increase the AsO4 contents of the products up to 16%. However, the products consist of hematite together with As04-containing Fe(SO4)(OH) and an unknown Fe-AsO4 species. All the hematite products contain - 1% SO4 which appears to be adsorbed on the nanometer-size hematite crystallites.IntroductionDissolved iron is a common impurity in most hydrometallurgical processing circuits and, generally, the iron must be eliminated prior to the subsequent recovery of the sought after metals. Simple neutralization of iron-rich solutions yields slurries which are difficult to thicken and filter. To address these concerns, the jarosite, goethite and hematite processes have been developed, and these technologies are able to reject the dissolved iron in a readily filterable form [1]. Despite its higher cost, the hematite process offers several potential advantages. Because hematite is an iron-rich, high-density compound, its formation would reduce the mass of residue and the size of a residue storage pond. Hematite is the thermodynamically stable form of iron under ambient conditions, and this stability would facilitate the impoundment of hematite precipitates. Furthermore, hematite has some market potential for cement manufacture and even for iron making [2]. In all the commercial hematite processes, the dissolved ferric ions are first reduced to the ferrous state. Subsequently, the pH of the solution is adjusted and the solution is then oxidized. The ferric ions gradually generated during solution oxidation hydrolyze and precipitate mostly as hematite, although commercial hematite products also contain trace or minor amounts of jarosite-type compounds. However, there are potential advantages in precipitating hematite directly from ferric ion solutions, as the reduction and subsequent oxidation of the iron are not required. Although the precipitation of hematite directly from relatively concentrated ferric sulphate solutions (up to 0.5 M Fe(SO4)is) was recently demonstrated [3], the behaviour of impurity species during hematite precipitation is largely unknown. To address this issue, systematic laboratory experiments were undertaken to ascertain the behaviour of a number of ""impurity"" species during the precipitation of hematite directly from ferric sulphate solutions at 225°C, and the results are presented in this paper."

Jan 1, 2012

By A. H. -J. Siegmund

Since the last survey of lead smelters in 1987, the lead industry has experienced many changes. Technological innovations, in combination with a dramatic shift in the market structure as well as more stringent government regulations, caused major upheavals in many different areas. Therefore, a new survey was performed to review the progress in the technology of lead recovery over the least decade. The newly conducted survey reflects all current phases of the world's primary lead production, from charge preparation to refined metal shipment. It was prepared by sending questionnaires to individual companies, and the detailed statistical data of this survey are presented. In considering the data developed from the survey, it should be recognized that the primary lead industry is at a crossroad where novel technologies will gradually substitute the sinter machine - blast furnace operation in the new millennium.

Jan 1, 2000

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"One of the methods for waste treatment is composting during which as a result of controlled biological decomposition of organic waste in aerobic conditions harmless materials are received. Composting takes place in suitably designed premises which ensure the optimal conditions for biochemical decomposition of the waste. A usual way to process composting is the spreading of the waste on a base made from reinforced concrete.In the paper the phases and basic technical features of the process of composting, the requirements and properties of the base and the ways of protection of concrete base against corrosion are revealed. Technical decisions for a specific construction site in Bulgaria are shown and the advantage of achieving durability of the concrete constructions in the plant while achieving simultaneous environment protection from pollution is discussed.IntroductionComposting is the process of controlled biochemical decomposition of vegetable and animal organic waste in aerobic conditions as a result of which harmless materials are obtained. The latter have better stability and are rich in humus substances which are useful for agricultural crops and can be used for restoring the soil fertility [1, 2, 3, 4].In modern waste treatment plants a composting technology is adopted in which the waste is spread on a concrete base as piles with certain dimensions [1, 3]. These piles are periodically stirred or air is blown through them in order to ensure the quantity of oxygen required for the process of aerobic decomposition of the organic matter. The fluids and gases formed in the course of the composting are take away in order not to pollute the environment – air, water, and soils. For this purpose the base on which the waste is spread must satisfy certain requirements, and the gases must be taken away and rendered harmless in order to protect the atmospheric air from pollution. This paper discusses the need for protecting the concrete base from corrosion and characterizes the stages and main parameters of the composting process and the possibilities for primary and secondary protection of the concrete base from corrosion. Specific technical decisions applied in a composting facility in the area of the town of Plovdiv are presented."

Jan 1, 2008

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By Rachel De Lucas

In recent years, as the price of oil soars upward, scientists have started to focus on other energy sources, such as hydrogen. As magnesium can be used for hydrogen storage by forming MgH2, industry will see a growing demand for the hydride. In hydrogen storage and release cycles using magnesium, hydrogen is released from magnesium hydride through hydrolysis and magnesium hydroxide is produced. Therefore, recycling magnesium hydroxide back to magnesium becomes important. The solid oxide membrane (SOM) process is an emerging technology for this process. In the SOM process, MgF2-CaF2-MgO flux is contained in a stainless steel crucible, which works as the cathode. An ionic-conducting YSZ membrane, connected to a liquid metal anode, is partially immersed in the flux. During electrolysis, when the voltage between anode and cathode is higher than the dissociation potential of magnesium oxide, magnesium ions move toward the cathode and are reduced into magnesium vapor. The oxygen ions move toward the anode, passing through the YSZ membrane. They are then oxidized, forming pure oxygen, CO/CO2 or steam (by reaction with hydrogen). The magnesium vapor, generated at the cathode, is collected in the condenser as high purity magnesium. SOM experiments have been conducted with different liquid metal anodes and without reductants. The SOM technique is a highly energy efficient process and with by-products being oxygen or steam, it is also an environmentally friendly green process. A 2-D electrostatics mathematical model was developed as an initial step towards optimizing the design for a three-tube scale-up SOM electrolysis cell. Several possible geometries were examined to develop the scale-up model and convergence of the model was achieved.

Jan 1, 2006

By R. M. Donovan

This paper documents the efforts to improve quality and production at the Amarillo Copper Refinery. It summarizes the change in attitudes, work procedures, equipment maintenance, instrumentation, and the ever changing market. The Amarillo Copper Refinery is dedicated to the ASARCO Management System, ISO-9002 and continuous improvement.

Jan 1, 1999

By G. Hanko, A. Lebleu, M. Sibony, J. Lecadet

The New Jersey distillation process is today the most important pyrometallurgical method for the production of zinc of very high purity. The flexibility of the pyrometallurgical zinc production process, especially its ability for recycling, makes it competitive, although it is energy intensive. A deeper knowledge of the New Jersey process is necessary to further increase its technical performance by ensuring its global safety. A project, integrated in the European research program EUREKA, has been started in order to define the process chemistry of distillation. Experimental measurements have been carried out with a column at the laboratory scale, and the results, linked with industrial measurements, support the development of a model based on material and thermal balances. The first conclusions indicate that the key parameters for process optimization are the column geometry and the distribution of the thermal losses.

Jan 1, 2000

By Roberto Parada

In a long term program for the optimization of the Outokumpu Flash Smelting Furnace at Chagres Smelter many different subprograms are being developed. One of them is the design and application of a sampling method that can allow the direct diagnostic of the quality of the copper concentrates combustion. We present in this paper the evolution of the sampling devices used in a ten months of continuous sampling campaigns and an example for the sulfur elimination and magnetite formation in the flame from 60 cm to 100 cm under the burner. These type of information combined with the appropriate mathematical modeling of the combustion must propose some considerations to correct the classic criteria in the preparation of the charge for the smelting of copper concentrates based only on the mass and energy balance from the chemical and mineralogy composition of the concentrates.

Jan 1, 2006

By Okechukwu Anopuo, Gerhard Tober, Petra Maier

"In this study, an investigation on the microstructure of hot rolled steel S355J2+N was conducted to optimize process parameters of complex forming, which combines rolling and bending. The best sets of parameters are worked out based on homogeneous mechanical properties and microstructure within the varied deformation degree with maximum at <p = 1.14 on a 25 mm thick plates. Mechanical properties, especially of heavy plates, are strongly influenced by the local deformation degree, strain rate and temperature. Detailed microstructural analyses showed that the ferrite-pearlite band structure changes near the surface, while maintaining homogeneous microstructure within the deformed work piece. Surface decarburization was also observed and this leads to decrease in hardness. To minimize iron oxide formation which could lead to side cracking, reduction in exposure time to temperature was suggested. On the other hand, temperature reduction below a critical value would risk the accurate forming process.IntroductionThis work presents the preliminary results of research to develop a new complex deformation process of thick steel plates. Complexity is given because the forming process combines rolling to reduce thickness and profiling by bending. The work piece will experience a thickness reduction from 25mm to 8 mm and is double curved. To explain and understand forming of thick plates basics of sheet forming as well as massive forming need to be used. At the moment there is no forming process established to produce double curved plates including reducing thickness in one process step. Technologies nowadays consist of two process steps: flat rolling and pressing in shape. Due to good weldability and formability the final product will be made of steel S355J2+N. This low-carbon steel is well understood and has a low strengthening exponent, which is expected to keep the forming forces down. Reduction of thickness from 25 mm to 8 mm gives furthermore a high deformation degree. Thus, hot forming has to be applied. The determination of process parameters is the main aim of overall research project; temperatures above lOOO°C are expected. Flow curves in literature are given at various temperatures and strain rates [1]. However, experiments with data close to the industrial application are rarely found, especially at low strain rates and high deformation degrees. Pre-test were done by flat rolling, being aware that the influence of bending is eliminated. The microstructure evolution were characterised in relationship to material formability with special attention to grain size change and recrystallization. Representative samples should be selected from specific locations in the deformation zone according to the knowledge about the metal forming process [2]. Due to no further alloying elements in S355, no precipitation hardening is expected to take place during hot forming, which keeps the mechanisms simple and the concentration on the feasibility of the complex forming process is given."

Jan 1, 2012