Search Documents

By I. D. Reznik

Results of thermodynamic computations have been presented for reactions occurring in the process of segregation roasting of oxide nickel ores to describe more accurately the mechanism of the process. Under conditions of laboratory-scale roasting in combination with close-circuit flotation flow-sheets and magnetic separation, a recovery of 80-82% of nickel into 8 to 10% Ni concentrate and a recovery of up to 66% of cobalt was achieved. Process conditions have been selected for processing of both high-iron and high-magnesium ores. The feasibility of conversion of 94-98% of nickel and cobalt into solution by oxidizing pressure leaching with sulfuric acid has been demonstrated. It has been substantiated that it is reasonable to introduce double-stage segregation roasting.

Jan 1, 2003

By Paykan Safe

This paper reviews various process off-gas cooling options available for sulfide smelting processes. Advantages and disadvantages of each, system are discussed along with the selection criteria for a reliable and cost effective :system. Various systems are presented to demonstrate typical process parameters for smelter off-gas handling systems and to outline operating difficulties associated with each system:

Jan 1, 1998

By Eric J. Grimsey

Nickel smelting and converting can be viewed as processes in which iron is either partitioned or transported between matte and slag. Metal recovery depends on the mass of iron transported to slag, the thermodynamic environment in which the transport is made, and the extent to which the slag, once formed, is left in contact with the matte. The importance of these effects is discussed with reference to a new equation which describes metal recovery in terms of a mass balance and a thermodynamically related parameter which is easily measured in practice.

Jan 1, 1993

By Rodney J. Ishak

The reduction of Mn3O4 to MnO has been investigated in a thermobalance apparatus, The charge was composed of manganese ore (decomposed by heating/calcination or pre-reduction to mainly Mn3O4) and coke. The material was charged to a crucible, which was suspended in the balance. CO-gas was distributed through a grid in the bottom of the crucible. Two sizes of ores were used; 2.4-4.8 mm and 6,7-9.5 mm. Coke particles were in the size range 4.8-6.7 mm. Experiments were conducted in the 900-1100°C temperature range. The composition of the product gas was monitored continuously. External mass transport between bulk gas and particle surface does not seem to limit the rate of reduction. Assuming that both diffusion through product layer and chemical reaction at the interface between MnO and Mn)04 are rate controlling, the data was tried both in a shrinking core model and in a grain model using regression. The grain model gives the best physical description of the process, because the reactant is in fact a porous medium. With this model the effective diffusivity was calculated to be in the 1.5-6.10.5 m2/s range. The pore size was mainly between 0.1 and 10 um,

Jan 1, 2003

By H. Senoh

For the purpose of clarifying the reason caused a drastic decrease of discharge capacity for MmNi3.6Mn0.4Al0.3Co0.7 electrode at relatively low temperatures, various factors influencing the charge-discharge processes were investigated in the temperature range of 25°C to -40°C. The charge efficiency obviously decreased at low temperatures less than 0°C due to a decrease in the rate of the charge-transfer reaction on the electrode surface. Moreover, both the rate of the hydrogen diffusion from the alloy bulk to surface and the rate of the charge-transfer reaction significantly influenced the high-rate dischargeability. The addition of Mo to MmNi3.6Mn0.4Al0.3Co0.7 alloy was found to be effective for improving the electrocatalytic activity, leading to the improvements of the charge efficiency and the high-rate dischargeability at relatively low temperatures.

Jan 1, 2002

By Chen Yongming

In order to eliminate the serious environmental pollution caused by low concentration of sulfur dioxide smoke in antimony smelters, a new smelting process, named as reducing-matting smelting, is proposed in this paper. The effects of technical conditions such as smelting temperature, smelting time, Pyrite cinder addition and the amount of additive on the smelting of stibnite concentrate have been investigated by the method of single-factor experiment. The results show that the optimum conditions are as follow: The amount of pyrite cinder is 1.2 times of its theoretical amount. The addition of soda and sodium sulfate is 15% and 72.6%, respectively, to the amount of stibnite concentrate when the total amount of sodium is 30%. The reducing-matting smelting is conducted at 1100°C for 2h then the smelting temperature is raised to 1200°C for 50min. Under the optimum conditions, the direct and total recovery ratio of antimony can gain 90.99% and 98.87%, respectively, and the fixed ratio of sulfur is higher than 99%.

Jan 1, 2006

Mount Isa Mines Limited (MIM) and the Commonwealth Scientific and Industrial Research Organization (CSIRO) have, over the past 15 years, jointly developed the Isasmelt process. This process is based on the use of the Sirosmelt top-entry, submerged combustion lance, developed by the CSIRO in 1973. While the Isasmelt technology was first applied to lead smelting, it has more recently been adapted to smelt copper concentrate. A 15 t/h demonstration Copper Isasmelt plant was commissioned in MIM's Mount Isa copper smelter in April 1987. The success of the Copper Isasmelt demonstration plant, which smelted over 532,000 metric tons of copper concentrate, has led to the construction of two full-scale furnaces: a 104 t/h furnace in the Mount Isa copper smelter, and a 585,000 t/y (650,000 short t/y) furnace at the Cyprus Miami Mining Corporation smelter at Miami, Arizona. The commissioning of these furnaces commenced in August and June 1992, respectively. The MIM Copper Isasmelt furnace will raise the Mount Isa copper smelter's capacity to 265,000 t/y of copper. The plant includes several innovative features, including: Andritz pressure filters, a rotary holding furnace, and an Ahlstrom flux-flow boiler.

Jan 1, 1993

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By M. J. Walker

The lead .smelter at Cominco's operations at Trail, B.C. has been undergoing. a modernization program since 1986. In that year a contract agreement was reached with German-based Lurgi GmbH which allows Cominco to construct and operate a lead smelter using Lurgi's QSL process. Cominco Engineering Services Ltd. (CESL), a subsidiary of Cominco Ltd., was contracted to provide project management, engineering, procurement and construction management? services for the project. The new smelter replaces the existing sinter-blast furnace plant ?and will have a capacity of up to 1601000 tonnes per year of refined lead. This new smelting proc.ess results in significant operating cost reductions and major environmental .improvements. Start-up of the new plant is scheduled for the fall of 1989. The metallurgy and the operating parameters, important to the design of the new smelter, are described together with projected deportments of lead, zinc, silver and minor metals. A plant description, will be given for the following major areas that make up the modernization project: the pressure filter operation for the preparation of ,zinc leach residues feed material, the QSL reactor and boiler itself, together with its feed system and process gas treatment, and the drossing plant with a new continuous drossing furnace and oxygen softening and thallium removal. Slag from the QSL reactor will be treated in existing slag furnaces until a subsequent second phase of the modernization is completed in the 1990s.

Jan 1, 1990

By P. Peczak

A Monte Carlo simulation technique has been used to study dynamic recrystallization in polycrystals. A continuum microstructure of the polycrystal is modeled employing a discrete lattice. The response of the material to hot deformation is simulated by adding stored energy and recrystallization nuclei continuously with time. The experimentally observed nonuniform character of deformation substructures is modeled by employing a phenomenological expression for inhomogeneous distribution of the stored energy. All simulations were performed on HP-Apollo 9000 Series 700 workstations. A program written in FORTRAN with use of PHIGS graphics library calls was used to interactively monitor the current state of the matrix and all relevant parameters: deformation stress, average grain size and effective nucleation rate. Visual analysis of the simulated microstructure allows a better understanding of the data developed by averaging over a number of very long Monte Carlo runs. Since the essential features of dynamic recrystallization are accurately reproduced by the model, it is used to discuss the role of the controlling mechanisms of the dynamic recrystallization in real polycrystal.

Jan 1, 1993

By Neil Smith

Mineral processing plants typically procure a range of industrial services from contractors. Their satisfaction and value received is directly affected by how the services are procured, rationalized and delivered. Conventional purchasing strategies often focus on price rather than on optimizing the service relationship between supplier and customer. The nature of this relationship may have the greatest potential to reduce costs and enhance production. It has been documented that a service involves simultaneous production and consumption. A high degree of customer involvement is often necessary for a successful outcome and the expectations and attitudes of the customer can positively or negatively affect delivery of the service. This indicates that the customer can enhance or diminish their own satisfaction and value received and the supplier cannot act alone for best results. The Optimax? Program for industrial services is a service delivery framework whereby a customer and supplier work together to raise the efficiency of the service exchange. The Optimax? Program is intended to help the customer optimize costs and maximize production by connecting the customer and supplier through shared information and objectives. This paper will review the basic nature of services, provide a couple of examples of conventional procurement strategies for services and outline the features of the Optimax? Program. A Case Study showing recent results from implementing the Optimax? Program will be included.

Jan 1, 2006

By P. J. Uggowitzer, K. Steinhoff, A. Wolf

"With the increasing acceptance of the Thixoforging process in the last few years, also the technical and commercial requirements for this forming technology and its components increased. So far, a great deal of work has been done in the development of an efficient process and control design. However, less attention has been paid to the development of new specifically tailored aluminum wrought alloys for this specific manufacturing process. · In this paper a new AlMgSi-alloy (A6082), optimized for the Thixoforging process, is presented. In the first part, the technical potential of the new alloy is specified by its microstructural evolution and flow characteristics in the semi-solid state. In the second part, the mechanical properties of thixoforged components of different conventional AlMgSi-alloys a (e illustrated · and compared to the new alloy.IntroductionSemi-solid metalworking, also known as semi-solid forming, is a hybrid manufacturing method that incorporates elements of both casting and forging. The key to the process relies on the peculiar flow behavior of slurries containing non-dendritic solid, which was first studied at the MIT by Flemings et al. [i], in the early 1970s. It was discovered, that if an alloy is uniformly stirred during freezing, discrete rounded particles of solid are formed rather than the normal dendrites, and the slurry is highly fluid (-5 Pas) up at least 50% solid. In addition, these slurries posses thixotropic flow characteristics: the viscosity is dependent on sheare rate and time. The more vigorously they are stirred, the more fluid they become. However, on standing the viscosity recovers and the material stiffens (-106 Pas).The semi-solid forming process exploits this phenomenon. In a first step, the required non-dentritical- microstructure is obtained by mechanical or electromagnetic stirring during primary solidification of the alloy. The stirred slurry is generally fully solidified as a feedstock billet and - in a second process step - reheated above the solidus temperature into the semi-solid state. In this condition, the thixotropic properties permit the material to be handled by robotic devices and transferred to a die (Thixocasting) or subjected to- a forming process by means of forging (Thixoforging). Owing to the shear stress which acts on the semisolid material during forming operation, the viscosity of the material is reduced attaining so the desired fluid-like flow characteristics."

Jan 1, 2000

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Ray Y. Lin, Randall A. Blue

"Joining of silicon carbide with infrared using a mixture of Si-30wt.%C as the brazing material has been investigated. Joining was performed at a temperature of 1500 °C in a flowing argon atmosphere for processing times ranging from 5 to 60 seconds. The joining filler materials include thin film silicon obtained by thinning down silicon wafers to about 70 /!m and graphite powder of a 15 /!m average particle size. Joint strengths were determined with a specially designed shear-in-compression jig for testing shear strengths of brittle materials. Cross section examinations of the joined specimens with optical microscopy, scanning electron microscopy and transmission electron microscopy have shown that all joints are essentially void free with excellent wetting between the base SiC and the brazing material. Silicon carbide in the B form has been identified as the reaction product in the joining zone with a transmission electron microscope (TEM) and selected area diffiaction (SAD) analysis. At 1500 °C with a joining time of 60 seconds, the joint has consisted of primarily SiC. With such a high SiC content in the joint, the joint strength is comparable to those by other joining techniques, such as diffusion bonding, as reported in the literature. A kinetic model for the formation of SiC from liquid silicon and carbon is proposed to explain the observed joint microstructural evolution.IntroductionSilicon carbide is of great interest for high temperature structural applications because of its excellent high temperature strength, wear resistance and anticorrosive characteristics [1]. Even though the interest in SiC is high, the use of the material has been limited by the high cost and difficulties involved in forming components of complicated shapes [2]. It is these limitations that necessitate the development of effective joining techniques that are cost effective and able to provide strong joints."

Jan 1, 1996

By David B. Dreisinger

Mass and heat balance modeling is a powerful tool for the design and analysis of hydrometallurgical process flowsheets. In this first of two papers, we examine the basic fundamentals of mass and heat balance modeling, and apply these concepts to several flowsheets using a simple spreadsheet model. In this way, we aim to demonstrate how such models are not only easy to construct, but can also be indispensable for comparing various flowsheet alternatives, for making rational economic decisions, and for developing a basic understanding of existing process behaviour.

Jan 1, 2002

By Srinath Viswanathan, Adrian Sabau

"In general, the occurrence of microporosity during metal casting is due to the combined effects of solidification shrinkage and gas precipitation. The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies on microporosity, it is considered that the porosity formation does not influence the fluid flow in the mushy zone. In this study, a computational methodology is presented for the numerical simulation of interdendritic fluid flow and microporosity evolution. The solution algorithm presented includes a fully coupled, implicit treatment of microporosity and local pressure in the mushy zone. The effects of microporosity evolution due to the local pressure drop in the mushy zone, and pore expansion in casting regions where liquid feeding alone cannot compensate for the solidification shrinkage are also considered. It is shown that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops. By its growth, microporosity partially compensates for the solidification shrinkage, reducing the feeding demand. A reduced feeding demand requires less fluid flow to compensate for solidification shrinkage, and results in smaller pressure drops in the mushy zone. Therefore, in order to accurately describe casting defects, comprehensive models of fluid flow, heat transfer, and solidification must include the effect of microporosity as well.IntroductionIn the terminology commonly used by foundrymen, porosity is usually considered to be either ""hydrogen"" or ""shrinkage"" porosity. Hydrogen porosity is the term given to porosity that is generally rounded, isolated, and well distributed. Porosity that is interconnected or clustered, and of an irregular shape corresponding to the shape of the interdendritic region, is usually termed shrinkage. In general, the occurrence of microporosity in aluminum alloys is due to the combined effects of solidification shrinkage and gas precipitation [1]. Continuum models [1, 2- 7] have been used to predict the level of porosity in castings. A number of other studies have also attempted to understand the phenomena of porosity formation and pore growth [8-10] and pore morphology [11].The governing equations for fluid flow and hydrogen evolution indicate that porosity formation and fluid flow are strongly coupled. However, in most studies [4, 9, 10], it is considered that the porosity formation does not influence the fluid flow in the mushy zone. Kubo and Pehlke [3] presented a methodology for the prediction of microporosity distribution in shaped castings by considering the effects of both the hydrogen precipitation during solidification and the pressure drop in the mushy zone. In their approach, the local pressure and porosity were computed in an uncoupled manner based on a ""flux of interdendritic liquid"" criterion, i.e., either pressure or porosity was first computed using the other variable at the previous time step. Their approach has been used with little change in numerous studies [6, 12, 13]. Recently, Kuznetsov and Vafai [14] presented a fully coupled, one-dimensional model for the computation of pressure and porosity. They showed that neglecting the effect of porosity formation on the pressure in the mushy zone yields higher pressure drops and an over-prediction of final porosity. They also showed that the influence of porosity formation on the pressure is larger at lower pressures in the mushy zone."

Jan 1, 2001

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By A. V. Tarasov

The proposed process is based on creating a controlled frothed layer of molten slag, in which fine particles of carbonaceous reductant and raw material to be processed are mixed with emulsified iron. Frothing of the slag layer without external blowing occurs as a result of intensive evolution of gaseous reduction products. The froth reaction process is maintained due to the heat of an electric arc in the slag layer. When the metal bath is heated by the arc to 1400- 1 500°C, the low temperature of the slag surface of about 1200-1 300°C is maintained due to low thermal conductivity of slag froth preventing heat loss. In order to maintain the required slag froth level and control the process temperature, air tuyeres are installed above the slag bath; blowing air serves also for oxidation of zinc in fumes and for its transportation. High adsorption and thermal insulating properties of slag froth ensure virtually complete elimination of dust and mist entrainment along with low heat losses. The main macrokinetic regularities of the carbon thermal reduction of zinc-containing slag melts have been studied under frothing conditions. The mechanism of formation of gas-slag emulsion has been identified under the conditions of reaction [C]+[O]=CO occurring locally at the slag-metal interface. It has been demonstrated that under the froth reduction conditions the zinc removal rate from the melt increases on the average by 3 to 5 times. Based on the physical and chemical data obtained, basic principles of the dezincing technology have been developed for different intermediate oxide iron-containing products produced in the process of ferrous and non-ferrous metals production.

Jan 1, 2002

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By R. H. Hanewald

The INMETCO process has been modified so as to recover nickel. chromium and Iron from a wide variety of metal containing waste-streams. This now includes the recovery of metals from spent acid solutions such as chromic acid etching I1quids. nJcke1 and chromium plating solutions; stainless and superalloy pickling solutions. etc. In addition. hazardous electric furnace stainless steel and. superalloy baghouse bags can be processed so as to recover the valuable metall1cs. A detailed review of the above new recovery techniques w1ll be discussed as well as the current operating methods used at INMETCO.

Jan 1, 1992