Search Documents

By Kelly J. Driscoll

Impure zinc (98.5%) was electrorefined to high purity zinc (99.995%) using a fused salt electrolyte of molar composition 1: 1 : 1 :2 ZnCI2:KCl:NaCl:LiCl with a current efficiency of about 90% at 723 K. A recessed channel electrorefining cell was developed which achieved excellent mixing of both the metal and the electrolyte and by ensuring a very small anode to cathode spacing the voltage drop across the cell was 0.16 V and at a current density of 7kA m-2. The physical characteristics of the cell were observed using a low temperature model which showed the formation of droplets and rivulets which provided mixing. The application of this approach to the refining of other non-ferrous metals is discussed.

Jan 1, 1992

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By D. Gregurek

In non-ferrous metal furnaces the installed magnesia-chromite refractory lining is exposed to several stresses, rather complex in their interaction. Therefore, a detailed investigation and understanding of wear mechanisms through “post mortem studies” is an important prerequisite for refractory producer. Additionally, in order to determine the most suitable refractory products and to improve the lining life of refractories, practical corrosion testing with processing slags is performed. For this purpose the test-facilities, such as induction furnace, rotary kiln but also cup test and drip slag test, allow the best possible understanding of chemothermal brick wear on pilot scale. Prior to testing a complete mineralogical investigation, thermo-chemical calculation via FactSageTM of the slag was carried out. Based on such research results, combined with specific process knowledge RHI Magnesita can recommend appropriate brick lining solutions for non-ferrous metal furnaces.

By James W. Reeves

DuPont was the titanium metal pioneer who put the greatest effort into both R&D and commercial sponge and powder metallurgy production. This was concentrated in the period 1945 through 1963. The commercial results were development of the chloride process for TiCl4 using ilmenite, development and improvement of the Kroll process, development of a modified Hunter process to make titanium powder and commercial development of a direct powder process. The powder metallurgical process failed because of the inability to meet powder chloride specifications. All this work remained a trade secret until published in NMAB -392 by Mahla in 1983. There were other processes explored by DuPont, both improved sponge and powder processes. Much of this work has been continued by others but none, as of yet, resulting in new improved titanium metal capacity.

Jan 1, 2001

By G. Haesebroek

In L969 Metallurgie Hoboken-Overpelt started an industrial plant for the separation of iron and zinc from a concentrated CoCL2 solution. Iron and zinc are extracted in column contactors by a solvent containing 12 vol % of tertiary amines in xylene. The extracted metals are stripped from the pregnant organic phase by precipitation with a NaOH solution at pH LL. In this paper an overview is given of the industrial process. In order to overcome some drawbacks of this process (low flash point of the diluent, reagent consumption, batchwise stripping) an alternative solvent extraction process has been examined. In this alternative process, iron and zinc are extracted with an or¬ganic phase containing 50 vol % of TBP in Escaid 110. The pregnant solvent is stripped with water in conventional mixer settlers. Despite the ability of this process to overcome most of the inconveniences due to the use of tertiary amines, it suffers from the poor stability of TBP in concentrated chloride solutions, resulting in unavoidable and inacceptable precipitation phenomena in the stripping section.

Jan 1, 1988

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By C. Hennesmann, D. Maijer, S. L. Cockcroft, P. Yo

"Die cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. As part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Auto Parts Toyota Incorporated, work has been underway to predict heat transport and porosity formation in die cast A356 wheels. The basic heat transfer equations have been solved using the commercial finite element package ABAQUS to which specialized routines have been added to predict porosity. Preliminary work on predicting porosity formation focused on using the Niyama parameter as a measure of the probability of porosity. The latest version of the model incorporates a new fundamentally based porosity criterion, which takes into account the effect of hydrogen concentration. The development of this model together with its application to a series of cylindrical test castings as well as a production cast wheel are presented.I. IntroductionDie cast aluminum wheels are one of the most difficult automotive castings to produce because of stringent cast surface and internal quality requirements. Microporosity, in particular, is a common defect that can adversely affect wheel quality. The mechanism of microporosity formation in aluminum alloys is complex owing to its dependence on the interaction of a number of phenomena occurring during solidification including the decrease in hydrogen solubility, the decrease in volume, the development of the solidification structure, and the increase in difficulty in interdendritic feeding [1]. As a result, the amount, size, and distribution of microporosity is affected by a large number of casting parameters including thermal variables, melt composition, grain structure, modification, and inclusion content, making optimization by trial-and-error methodologies difficult.The use of criteria functions, based on thermal conditions during casting, offers a relatively simple approach to predicting microporosity. In practical terms, they are useful because they provide a straightforward method of assessing the impact of varying casting parameters on porosity through various thermal parametersl21 such as thermal gradient, cooling rate, solidification time, and solidus velocity. Drawbacks of criteria functions include insensitivity to varying hydrogen concentration and the limitation to qualitative predictions. Consequently, in aluminum alloys, attempts have been made to develop models incorporating the effects of hydrogen gas and microstructure evolution. However, these types of models represent a significant increase in complexity and sacrifice the simplicity and ease of application of the thermally based criteria functions."

Jan 1, 2001

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By Hai-Xing Fang, Bing Xie, Hong-Yi Li

"In the duplex melting process, chromium forms chromium spinels, the study of which will help to exploit the Hongge ores (rich in chromium) in the Panzhihua-Xichang area in China. Mimicked chromium slag was synthesized. The oxidation and decomposition mechanism of the Fe-Cr spinels contained was studied in a sodium roasting process. The effects of temperature, roasting time, amount of soda added and filling reagents were investigated. The leaching-reduction-precipitation-calcination procedure to extract Cr2CO3 was optimized. The results showed that the optimized roasting temperature was 1000~1020°C with a stoichiometric Na2CO3 addition and without any filling reagents. Roasted materials were leached with distilled water and were filtered to obtain a chromium-containing solution, which was adjusted to pH 1.60-1.80. A reducing reagent, NaHSO3, was added in a stoichiometric ratio and the solution was then adjusted to pH 7.25~8.25. Maximum Cr2O3 precipitation was obtained and the precipitate was calcined at 1050°C for 2h to obtain Cr2Ü3 with recovery rate over 96%.IntroductionChromium is widely applied in the metallurgical industry, in refractory materials and in the chemical industry with its particular properties of hardness, wear-resistance, high temperature resistance and corrosion resistance [1]. There is no free state of chromium in nature and chromite is the main chromium containing mineral [2], China is poor in chromium resources, despite its large demand, and there are few deposits of high grade of chromite ores except in some regions in Tibet and Xinjiang province [1, 4]. Hongge, one of largest titanomagnetite mines in Panzhihua-Xichang area, is a polymetallic deposit mainly containing iron and titanium; it is also associated with various beneficial elements such as chromium, copper, nickel, etc. [3]. As investigated in Reference 3, the chromium reserves of Hongge ores are so large that it is of great importance to study how to extract the chromium from them."

Jan 1, 2012

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By D. McConchie

Management of caustic red mud wastes at the QAL bauxite refinery uses an innovative approach . involving neutralising the red mud with seawater; solids settle in a Red Mud Dam and residual water (pH = 8.6) is discharged to a tidal inlet. A survey of 18 trace elements in sediment, water, mangroves and molluscs, and an ecological survey of benthic fauna in the inlet, and at near-pristine control sites, revealed no significant trends that were linked to the discharge, except for the concentration of Al which was slightly elevated within 100m of the outfall. Trace element concentrations in water samples were close to, or below, world average seawater values and oysters collected near the outfall were acceptable for human consumption. The impact of discharges is minimised by a high tidal range, >60% flushing of the inlet in each tidal cycle, and the very high trace element binding capacity of sediment in the dam (> 100meq/ 100g dry mud).

Jan 1, 1996

By S. S. Ibrahim

The left behind material after the combusion of fossel fuel in some power stations in Cairo; weighing tens of tons every years, was investigated. The material called "Fly Ashes" containing 7.5% Ni, 10.0% V and 9.50% Cr; could be considered as a promising source of such valiable elements. As well as the small grain size (050 70 "m) of the material, and besides the complexity of their formation history, hydrometallurgical methods appeared to be the effective technique to deal with. Yet, preconcentration is possible by means of magnetic and gravity separation methods. The end product is assaying 16.60% Ni and 20.2S!; V with weight recovery of about 60.15%.

Jan 1, 1995

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By M. J. Adam

The U.S. Bureau of Mines is investigating the partitioning of selected complex minerals into simple phases using sulfidation reactions. Successful partitioning of complex mineralogy to simple phases may afford an opportunity to improve selective extraction of mineral constituents of economic value. The research has shown that complex minerals, such as chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9Se]' may be partitioned to the simpler phases covellite (CuS) plus pyrite (FeS2) and vaesite (NiS2) plus pyrite (FeS2), respectively. Demonstrations of these reactions were verified through long-react ion-time (24 h or more) experiments, but basic rate investigations and modeling were not included in the previous research. This report describes research aimed at determining the rate at which the complex mineral CuFeS2 converts to the simple sulfides CuS plus FeS2. Small samples of CuFeS2 were blended with elemental S prior to thermal treating under an He atmosphere for time periods up to 4 h. Products from each treatment period were characterized using metallography, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of the investigation revealed a rapid conversion of CuFeS2 to CuS plus FeS2 early in thermal treatment periods. As the reaction occurred, a CuS rimming of particles was observed which separated the reacting species (CuFeS2 and S) and caused a considerable decrease in transformation rate.

Jan 1, 1991

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By Anjan Kumari, B. K. Soni, Manis Kumar Jha, A. Vidyadhar, Vinod Kumar

"In the present paper, recovery of valuable metals from the poly-cracked ash obtained by pyrolysis of discarded PCBs has been studied following physical beneficiation and a hydrometallurgical process alternate to smelting. The ash is subjected to comminution for the separation of metallic components from non-metallic fractions by scrubbing, tabling and froth flotation which enriched the metal in the concentrate -97% which was further screened to separate high and low metal concentrate. The finer fraction containing -12% metallic value was leached in acidic solution. Almost all (Cu, Pb, Fe, etc) were leached in 4M HN03 at 90°C in 75 min at a pulp density 100 g/L. The characterization of both ash and residues were made by XRD, EPMA, EDS, etc. to validate the experimental results. The metals from the leach liquor could be recovered/separated using solvent extraction techniques which can further be processed to get pure metal salts/ sheets.IntroductionPrinted circuit boards (PCBs) are an essential component of electrical and electronic equipments (EEEs) as it plays an important role during operation of these devices. The world market of PCBs has reached nearly $60 billion in 2012, with 1.7 percent real growth over 2011 [1]. The diverse technology-driven global market is expected to grow at an average annual rate of 5% by 2014 [2]. The waste EEEs are generated due to replacement of obsolete equipments with modem ones and thus their demand is also increasing rapidly [3]. The discarded e-wastes are being piled up as landfills which affect the environment and cause health threats to living organisms, if not disposed of properly. These e-wastes contain metals some of which are precious, few are hazardous and others as valuable."

Jan 1, 2014

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By B. C. F1intoff, R. G. Bradburn, E. Groiss

"The concentrator at Brenda Mines Ltd. treats a copper - molybdenum porphyry ore with current head grades of 0.185% Cu and 0.036% Mo. The consistently low head grades provided the driving force to explore methods of improving plant productivity. Computer based process control was recognized as one means of addressing this objective. Over the period from 1974 to 1982 a control system evolved which now extends to every area of the mill. Control strategies are built on elements of classical, modern and rudimentary expert control. In addition, the control system has often served as a catalyst for other technological developments. The economic returns associated with the system are very significant and it has played an important role in the mine's survival in times of poor metal markets. This paper presents an overview of the computer control system at Brenda.PreambleOne can scarcely avoid picking up a trade magazine or newspaper today without seeing some reference to technology and its potential impact on North American business. _A recurring theme is the need to apply technology to raise our standard of plant automation in the manufacturing and process industries. The general thesis of these articles has been concisely captured in the mutually exclusive set:AUTOMATE or EMIGRATE or EVAPORATEProcess control is one form of automation that has been successfully exploited by various sectors of these industries. In minerals and metal processing the wide scale adoption of process control technology has, until recently, been largely limited to a few companies - most of whom have a history in the area dating back to the early 1970’s. However, there is definitely an increased and much broader interest in process control as a technology which can improve performance, productivity and profit.The economic hardships that were visited on the mining industry in the early 1980's are not easily forgotten. It is the authors' conviction that the mining industry must move to implement proven technology, in particular process control, in order to be well postured for the next (inevitable) down cycle.In pursuing the technical and trade literature, one can discover a number of example of the successful utilization of process control systems in mining and related applications. In the text which follows, the authors describe the process control efforts undertaken in the Brenda Mines Ltd. concentrator."

Jan 1, 1989