Search Documents

By Jiachen Wang

China is the largest coal producing country in the world. Coal is widely distributed in China and thus the mining conditions are complex and diverse. This paper summarizes the important achievements in the last 20 years in various mining methods including the extra thick seam with large mining height top coal caving, the thick seam with large mining height and top coal caving mining, the steep seam with top coal caving and fully-mechanized mining, the thin seam automated mining, and the backfill mining. At the same time, the rapid advance in the development of mining machinery and manufacturing has also contributed to the advancement of coal mining technology and the great improvement of coal mine safety. The future direction of China?s coal mining is to further improve mine safety as to improve the coal recovery rate, promote the pillar less mining technology, develop high-efficiency backfilling technology, develop steep seam high-efficiency mining technology for seams less than 10m thick, and high recovery mining techniques for extra thick seams, improve the reliability of mining equipment, and strengthen the protection and restoration of surface environments and water resources.

Jan 1, 2014

By Uwe Wyink, Guenther Thiele, Isabel Gollnick, Klaus Thyrock

"The application of a thin spray on liner was implemented in longwall T-junction sections in 2009 for the first time. The development of the material and the application is based on a technical cooperation between RAG Deutsche Steinkohle AG and BASF Corporation. The report gives an overview of the first trials. The underground test occurred in a seam with a height of 1.5 m (5 ft) in a depth of 1,100 m (3,609 ft). The roadway is dual-use entry and the roof strata is composed of shale and sandy clay. In some sections geological faults impact the surrounding strata. The poor conditions induce separating and loosening of roof rock. Several remedial actions have to be implemented for decreasing deformations at the face entrance.The application of thin spray on liner (TSL) provides simplification and cost reduction of supporting work at longwall T-junction. The installation of TSL to avoid roof and coal fall operations for lagging are omitted.INTRODUCTIONFor safe operation of face retreat in dual-use roadways, the processes of securing and stabilizing the face end area are very important in order to minimize deformation and stress. Avoiding roof and coal fall are the main concerns for safe operation. For that reason different methods of reinforcement are tested in underground operation. In this paper the application of TSL is presented.The specifications of TSL are described, followed by the case study results. The underground study is located in one mine of RAG Deutsche Steinkohle. The extraction of the hard coal in this mine is characterized by great depth and high stress. There are poor geological and geotechnical conditions. The roadway used for the underground application was headed with the support system combination type A, which will be described later in the paper. After the first face retreat, deformation of steel arch support and bagging destroyed the roadway, so for the second face retreat remedial actions had to be undertaken. For this a new system of reinforcement, simplifying the supporting work at the longwall T-junction was tested. The reinforcement consisted of different parts that are described in the following report. Furthermore two different versions were applied. One method is the operation with TSL and the other one is the use of concrete for sealing. Both methods are compared in the text."

Jan 1, 2010

By Richard N. Campbell

The world?s ever-expanding demand for energy and coking coals has resulted in the underground mining industry looking at taking on increasingly marginal and geotechnically challenging deposits. The drivers for this change include a reduced availability of open cut reserves and a lack of remaining ?good coal leases?. The lack of plum deposits is forcing some companies wanting to enter the coal supply market to purchase and operate in higher risk, lower margin areas. As geotechnical professionals, we are expected to develop strategies to facilitate safe and productive mining in ground that once would have been avoided. To be successful in these reserves, we are required to use every tool available, from exploration data to longwall automation, and invent or reinvent some new tools along the way. This paper presents geotechnical case studies of challenges in longwall mining and some of the methods developed and used to allow longwall mining to succeed where others said we would fail.

Jan 1, 2014

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

By Nengxiong Xu

The WTZ coal mine is located adjacent to an auxiliary dam in P. R. China. The mining-induced ground movements are calculated using a 3-D numerical procedure based on the finite difference method (FDM) to judge whether the extraction of the coal seam will have a negative impact on the dam. First, the values of the rock mass mechanical parameters in the numerical model are estimated using the available literature that relates intact rock and discontinuity properties to rock mass parameters. Then, based on available surface subsidence monitoring data for an area in WTZ mine, the main mechanical parameters of coal and rock masses are calibrated by a back analysis procedure that combines an experimental design technique with numerical simulations. Then the reliability of these rock mass parameters is verified. Finally, according to the planned mining sequence, predictions of mining induced surface subsidence are computed in steps, and the boundary of the ground movement area of each step is determined. The nearest distance from the boundary of the surface movement area to the edge of the dam foundation was found to be about 1347 m. The maximum surface subsidence within the mining area turned out to be 2.7 m, and the maximum settlement point was found to be close to west-south corner of A2 mined area. These findings led to the conclusion that the coal seam mining would not cause dam damage.

Jan 1, 2013

By Ashok Kumar, Rajendra Singh, Arun Kr. Singh

"A simple analysis of site conditions and capability of the mechanised depillaring (MD) operation found that this approach is suitable to address the strata control issues in coal pillar extraction under the weak and laminated roof strata of Pinoura mine. A continuous miner (CM) with a ram car and quad-bolter are used for single pass pillar extraction (first time in the country) to achieve a relatively faster rate of depillaring. A total of eleven panels are depillared under weak and laminated roof strata with a fair-rated rock mass rating (CMRI-RMR). It is observed that there is less influence of roof caving over the surrounding mining structures, especially those located out-bye the side of the extraction line. An attempt is made to quantify the goaf influence by field studies, which show that the maximum value of mining-induced vertical stress is 2.83 MPa, and the range of influence remains limited to around 15 m from the line of extraction. However, the problem of roof instability under the influenced zone was experienced due to the inherent nature of the weak roof strata. The chances of trapping of CM under weak and laminated roof strata of the panels is reduced by deriving a threshold value of the roof dilation, on the basis of a simple statistical analysis of the obtained field results. However, few incidences of roof collapses are observed over the CM due to the unpredictable behaviour of the geological structures below the freshly exposed strata, which also caused an obstruction in the speed of the extraction. This paper presents results of the field and laboratory studies, conducted for a successful application of the single-pass pillar extraction method, along with details of some CM trapping cases below the weak and laminated roof strata.INTRODUCTIONCoal is the major natural resource to meet the growing energy demand of India and this trend is likely to continue for the next 20 years in the country. A major part of the Indian coal belongs to Gondwana period, and only a small part belongs to Tertiary period. The estimated coal reserve in India per the exploration work done up to a maximum depth of 1200 m is 315.149 billion tonnes, including the proven coal reserve of 143.058 billion tonnes (CMPDIL, 2017). Even in presence of these huge resources of coal in India, there is a considerable gap between production and the users’ demand of coal. Most of the mines are operated by conventional semi-mechanised Bord and Pillar (B&P) methods; thus, the mining industry has gained a considerable amount of operational experience (Singh, Singh, and Dhar, 1996) and knowledge about strata behaviour (Singh and Singh, 1999; Singh et al., 2008) using this method. However, recently, the Indian coal mining industry has introduced some mechanised depillaring (MD) operations, where the level of production is relatively high. This approach of depillaring improves safety along with the production and productivity of a depillaring operation (Ram et al., 2017). The nature of the overlying strata of these depillaring operations vary greatly: from highly laminated, weak, and easily caveable to massive, strong, and difficult to cave."

Jan 1, 2018

By Joe Zelanko

In order to prevent roof fall accidents and injuries, U.S. underground coal mine operators must develop and implement effective roof control strategies. Various tools are available to assist engineers in developing designs. For example, criteria to address global stability issues (e.g., pillar stability) are well established in the U.S.; effective tools (e.g., empirical and numerical) are available to diagnose potential problems and avoid catastrophic failures. However, most miner injuries occur as a result of local instability (e.g., a roof fall in a single heading or a rib roll from a pillar corner). Hazard recognition and the availability of support plans suitable to those conditions are key to maintaining stability and safety on the working section.

Jan 1, 2011

By Denise Müller, Axel Preusse

"Due to multilateral underground use, mining subsidence is discussed more and more with regard to issues other than mining, such as post-mining topics, storage, or geothermal use. These discussions and the influence of the energy policy is why the situation in Germany is described as a transition from active to abandoned mining. Many PhD theses have been written within the last 20 years—every single one with a different topic but all with the same issue—the effects and challenges of mining subsidence.These challenges start with the research regarding geological and hydrogeological conditions, which is the basis for calculations like the angle of draw or predictions of subsidence due to water table drawdown. Furthermore, the research investigates issues like risk-management and financial planning. One of these issues is post-mining calculations; others include potential hazards of storage or the use of geothermal energy.This paper outlines an overview of German mining and the consequences due to subsidence. It deals with an overview of the circumstances related to hard coal mining, lignite mining, the use of geothermal energy, gas, and opportunities regarding underground storage. Basically, it describes the essential steps of processing mining subsidence, starting with monitoring to forecast and up to safety measures.With a glance back to the applied research of the prior two decades, we compare given forecasts with experiences already gained.Even though mining decreases, ground control does not.INTRODUCTIONAfter the Second World War, an economic recovery started in Germany, during which the mining industry provided an advantage. Areas like the Ruhr District or Saarland were characterized by hard coal mining. In addition, there was lignite mining in the Rhenish mining area and the middle German coal district. In the Lausitz area, there were gravel and sand companies for the construction industry and many other medium-sized mining companies. Especially in the Ruhr District and in Saarland, where large coal fields were built, mining played a major role. The number of mines increased, and the negative effects on the terrain got bigger. While minor open pits or quarries have influences on the landscape only, large open pits and underground mining lead to significant ground movements. This results in a larger importance of mining subsidence engineering. Calculations of subsidence and forecasts have been developed and refined within the last several years. Due to the fact that the mining areas were and still are densely populated, the forecasts are getting more and more precise."

Jan 1, 2018

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By C. A. Vining, J. R. Nopola

"Evaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. Evaporites are subject to continual creep and no amount of ground support can successfully arrest this process. Common ground-support techniques that are useful for most rock types may reduce the effective life of bolts in evaporite mines and can create unseen hazards. A different approach to ground support must be applied to provide long-term support in areas where high creep rates are present. The goal of effective ground-support designs in these situations is not to contain the rock and prevent it from moving; rather, the ground-support design must be able to move along with the rock and contain any fully detached slabs until additional remediation measures can be undertaken. The most appropriate ground-support designs will consider both the expected movement of the rock and the duration that the area needs to remain accessible.INTRODUCTIONEvaporites, such as salt and potash, pose unique problems to ground-support designs not encountered in other rock types. The factors that must be considered in design stem from the deformation behavior of salt, which can fail in a brittle manner, akin to most rocks, but can also deform in a slow, ductile manner, resembling the stretching and elongation of steel. The deformation behavior of salt has been well established in technical circles where it has been studied for decades (Hardy and Langer, 1984). Much of the research in salt mechanics is related to repository science, specifically at the Waste Isolation Pilot Plant (WIPP) in southwest New Mexico. RESPEC has been continually involved in the WIPP from the initial design considerations (Gnirk, Grams, and Zeller, 1977) to the current day (Keffeler, 2016) and has been able to leverage cutting-edge research of salt mechanics into practical solutions for mining operators. While a detailed description of salt mechanics is not provided in this document, Fossum and Fredrich (2002) include a fine overview of salt mechanics. The following list paraphrases their chapter on basic facts about salt to provide some context for the reader unfamiliar with salt mechanics:"

Jan 1, 2018

By Christopher Newman, Zach Agioutantis, Gabriel S. Esterhuizen

"As conventional underground deposits are continuing to be depleted, mining operations have been forced to produce at greater depths and in more geologically and geometrically challenging conditions. Over the past decade, there has been a global increase in the application of cemented paste backfill (CPB) material as a means of ground support in open stope mining operations. Although CPB has been extensively used within the industry, there are many fundamental factors affecting the design of safe and economical fill structures that are still not well understood. A critical design issue with respect to backfilled stopes is determining the stress state within the fill material as well as the surrounding rock.This paper details the development of a reliable numerical model for the simulation of stress distributions around the excavated stope area, as well as through the backfill material. Through discussions on modeling parameters and output results, one is provided with insights into the mechanisms of stress redistribution allowing for further accuracies in simulating the behavior of the CPB material as well as its interaction with the surrounding rockmass.INTRODUCTION AND BACKGROUNDModern technological innovations with respect to material processing, cementitious composition and chemical additives, and material transportation have provided the mining industry with a ground support material that greatly reduces mine waste costs, while, when used appropriately, increases reserve production and mine stability. As mining operations continue to produce in more complex geologic and geometric conditions, cemented paste backfill (CPB) has become commonly employed within primary-secondary excavation-support sequencing allowing for total extraction of the mining reserve. As shown in Figure 1, primary stopes are initially excavated and then backfilled in a two-staged pour: plug and final pours. The plug (initial pour), is initially placed at the bottom of the stope with a CPB material of heightened cementitious material. While the plug provides a strong foundation on which to build the rest of the CPB structure, it also provides protection against barricade breakthroughs (Li and Aubertin, 2009), as well as providing operations a means of underhand stope-and-fill mining through the use of an artificial sill pillar (Hughes, et al., 2011). Following placement, the plug is allowed to cure to a designated design strength. Upon completion of the plug, a less cementitious “final” pour material is used to backfill the rest of the excavated area."

Jan 1, 2018

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By Khaled Morsy

In this paper a new method to evaluate the stability of yield pillars was introduced. The evaluation of yield pillar stability was conducted in three steps: (1) Estimation of pillar loading - numerical modeling is a good tool to estimate the pillar loading for most of the geological, geometrical and mining conditions. In this study. finite element technique was used to estimate the state of stress, strain, elastic strain energy and plastic energy, etc. at every point within the pillar. (2) Defining the yield pillar loading zones¬. The proposed method considered the non-uniform stress distribution of yield pillars by dividing the area of the yield pillar into three loading zones, namely core, transition and rib zones. (3) Estimation of stability indicators - an appropriate stability measure was proposed for each loading zone. such as; Core Stability Factor. CSF, Pillar Bump Index, PBI and Rib Instability Index. RIF. A case study of successful and unsuccessful yield pillar application was used to assess the applicability of the proposed method.

Jan 1, 2003

By David K. Ingram

The objective of this U.S. Bureau of Mines (USBM) investigation was to characterize overburden response due to longwall mining. Subsurface strata and surface deformations were monitored at two sites in southeastern Ohio. Site A included two adjacent longwall panels. Site B consisted of one longwall panel. Both sites had similar mine geometries and overburden thicknesses. The major difference between the two sites was the rock strata within the overburden. Multipoint borehole extensometers (MPBX) were employed to measure subsurface displacements. Survey monuments were installed above the centerline and profile of each panel to measure surface deformations. Subsidence of the surface was observed before and after movement was detected in the MPBX units. Initial and final displacement of the MPBX units occurred at the same time at both sites. No deformation was detected outside the panel area. The development of overburden deformation was different over each panel. The final subsurface failure characteristics also varied between panels.

Jan 1, 1994

By Winton Gale

"The aim of this paper is to summarise the results and conclusions of Australian Coal Association Research Project (ACARP) Report Cl3013 which relate to water inflows into a mine which occur through the overburden above and adjacent to longwall panels. The study assessed available data of inflows into underground coal mines and utilised computer simulation of water flow through fracture networks. The study concluded that flow into mines is typically via an interconnected network of pre-existing and mining induced fractures. The height above the coal seam that mining induced fractures extend is typically related to the width of the panel. However the potential for those fractures to form a connected network which can facilitate flow, is related to the amount of subsidence and the depth of mining. The study compares model simulations with measured data and provides guidelines to estimate the average hydraulic conductivity of the overburden above extracted longwall panels in Australia.INTRODUCTIONWater inflow into coal mines has been a design issue for many years. Guidelines as to the potential for water inflow have been developed in many countries based on local experience and the form of mining being undertaken. In most instances, the guidelines relate to inflows which would endanger underground personnel and operations.In more recent times, water inflow criteria for mines has been widened to include lesser inflows which may not impact on mine safety or operations, but have the potential to reduce water flow within streams and surface aquifers. For the purpose of this paper the larger inflows which are readily measured in a mine or may impact on mining safety are defined as mine inflow and the lesser inflow relating to aquifer water loss as environmental inflow.The water losses referred to are those which enter the mine from the surface or from near surface aquifers.The empirical relationships developed as mine design guidelines or regulations typically relate to high flow (mine inflow) situations and in this paper, these have been reviewed as to their application to environmental inflow. In many cases environmental inflows were unlikely to have been noted or recorded in many mining operations in the past."

Jan 1, 2010

By Gift Makusha

Total extraction mining of coal is being undertaken on a small scale by Anglo Coal South Africa. Longwall mining has been done in the group at New Denmark colliery since the 80s and recently the company started experimenting with pillar mining at Goedehoop colliery. Total extraction mining methods result in caving of the overburden strata that is often accompanied by displacement of air causing wind blasts. The windblasts can cause injuries to underground mining personnel, damage to mining equipment, and ventilation disruptions. Some incidents of windblast damage and injuries have been recorded at both New Denmark and Goedehoop Colliery that prompted mine management to experiment with the goaf warning device, an instrument developed by CSIR mining technology to give early warning of impending god. The initial version of the Goafwarn was originally developed to operate as a stand-alone unit, with LED lights mounted on the device that would flash if the unit was triggered'. That set up would be effective in small working areas where the flashing lights are visible to all workers. This requirement is more difficult to satisfy in longwall application of the unit where mining activities are spread over large linear distances of up to 250 m and the flashing lights would not be visible to all workers in the longwall face. It was also found that the single unit had limitations in distinguishing between man made vibrations and cracking in rockmass leading to an unacceptably high incidence of false alarms. The case studies describe the experiments that were carried out to ameliorate the two issues mentioned above through networking more than one unit. This was achieved through the development of radio communication from the warning devices to a central control (Trollex Data Acquisition Unit) from which the alarms are issued once the prescribed triggers are satisfied. The operating system was made up of 4 Goafwarn units installed 30 m apart with 2 in the tailgate and other 2 in the main gate. The alarm state was defined where 3 or more units were triggered simultaneously. The concept was applied successfully in real time during longwall mining, and management procedures have been developed to achieve safety through the system including switching off the shearer, and flicking the lights to warn people.

Jan 1, 2005

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By Swapan Bhattacharya

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must 'adopt measures consistent with known technology in order to prevent subsidence causing material damage to the ex- tent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predict- able and controlled manner..." Implied in the constraints of Section 516 (b) (1 of SMCRA is a determination of what constitutes "material damage" to surface structures and renewable resource lands, and the capacity for sequential land use following underground mining. This Study was undertaken in an attempt to provide quantitative guidelines for estimating material damage to a wide variety of surface structures and renewable resource lands. Surface structures studied included buildings, bridges, railroads, highways. pipe- lines, d~, embankments, and water reservoirs. Damage criteria for buildings developed in this study along with details of the adopted methodology have been presented elsewhere (Bhattacharya et al.) (1). and will not be repeated here. Similar guidelines for renewable resource lands have also been discussed (Singh and Bhattacharya) (2)

Jan 1, 1984