Search Documents

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

Hydrodynamic investigations in exploratory boreholes and grouting holes are conducted for the purpose of obtain¬ing information about the hydraulic properties of the hydrostratigraphic section to be intersected by the proposed underground workings. The information obtained from the investigations provides the basis for calculating the hydrau¬lic coefficients of fractured permeable rock, the dimensions of the anticipated grout isolation curtain(s) around the un¬derground workings, the number and location of grouting holes, the injection pressure modes, and also the volume(s) of grout that will be required (Anon., 1976, 1978). The following data on each aquifer are obtained from the investigations conducted in monitoring and grouting bore¬holes and the analysis of the results: 1) the top of each hydrostratigraphic unit, 2) the thickness of each unit, 3) the ground water fluid potential distribution in each unit, 4) the coefficient of permeability, 5) the piezoconductivity, 6) the fracture porosity, 7) the geometry of the fractures in the rock, 8) the elasticity-compressibility coefficient of the fractured rock, 9) the chemical composition of the ground water, 10) the direction of flow of the ground water, and 11) the expected inflow rate of water into the shaft, drift or tunnel. STG uses its DAU-3M type flowmeter to conduct in¬vestigations of directions of flow in vertical, inclined and horizontal drillholes. The DAU-6 instrument is used to de¬termine the direction of flow of ground water in each frac¬ture or fractured aquifer. Various singular and double DAU type packers are used for pumping and for injection studies (tests) and for flowmeter investigations. Normally the instruments enumerated above permit in¬vestigations to be conducted in each separate aquifer with¬out reinforcing the holes with casings. On the basis of these investigative data, both the hydraulic properties of unfractured rock and the hydraulic properties of the fractured rock are estimated. Dual porosity rocks require special attention because they tend to segregate the grout. 3.1 FLOWMETER INVESTIGATIONS IN BOREHOLES The STG flowmetric methodology is based on the mea¬surement of the ground water flow rate through the borehole by hydrostratigraphic interval after the disturbance of the hydrostatic equilibrium in the "hole-aquifer system" (after pumping or injecting). The relationship of the head changes to the discharge into or from a particular hydrostratigraphic unit obtained during the tests serve as the basis for calcu¬lating the hydraulic properties. Flowmetric investigations facilitate the determination of the number of aquifers, their depths, their thickness, the hydraulic properties of the fractured rock and the magnitude and direction of the flow of ground water. 3.1.1 FLOWMETER HARDWARE STG conducts flowmetric investigations in boreholes using its DAU-3M-108, DAU-3M-73, DAU-3M-57 and DAU-3M-44 instruments.' They have respective external diameters of 108, 73, 57 and 44 mm. The type of flowmeter selected for use depends on the borehole geometry and the technological scheme for carrying out the investigations. Boreholes with a drilling diameter of 76-93 mm are inves¬tigated with the DAU-3M-73 flowmeter; boreholes drilled by bits with a diameter of 112 mm and more are investi¬gated using the DAU-3M-108 flowmeter. The DAU-3M¬108 and DAU-3M-57 instruments are used for flowmetric investigations with a packer. 3.1.1.1 The Downhole Sensor The sensor design of the DAU-3M-73 hole flowmeter is shown in Fig. 2. The design of the DAU-3M-108 instru¬ment is similar to the design of the DAU-3M-73 instrument. The frame of the flowmeter sensor shown in Fig. 2 consists of a casing, an upper and lower centering mount and two rings to which the guiding rods are attached. The upper rods are built into the connector bushing; the lower rods are built into the coupling sleeve. The borehole cable is attached using a half-coupling, a packing ring and a constriction nut. Thus, the frame of the flowmeter sensor is made so that the free passage of water to the impeller is facilitated along with the necessary rigidity. The primary moving component of the flowmeter is the double-bladed impeller, which rotates on cobalt-tungsten pivots and agate thrust bearings. Special extended air cham¬bers protect the supports of the impeller from the action of the borehole fluid which may contain fibrous and abrasive particles. The air located in the chambers shields the sup¬ports from direct contact with the borehole fluid when the sensor operates in a borehole. The hollow casing of the impeller serves the function of a lower cap. The upper cap is attached to the casing using a threaded connector; it is affixed also with a lock-nut. An adjusting screw with a

Jan 1, 1993

By K. Hartman

Certain external forces affect the manner in which business is conducted. and in recent years changes in the business environment have altered how some of these external forces affect the management of a business. These changes must be understood and considered in definition of the strategy of the business. Implementation of the strategy must assure commitment from all departments within a company, and this commitment sometimes involves compromises to assure that a department's goals mesh with the overall business objective such compromises must be externally motivated. i.e. for benefit of the customer. Complete implementation transcends internal departments to all aspects of managing the efforts in the marketplace.

Jan 1, 1989

By A. T. Sapulek, C. S. Özveren, D. W. Dixon

The prediction of underground methane emission from longwall coal faces has been extensively researched for a number of years and numerous prediction methods have been devised. Many coal mines employ sophisticated environmental monitoring equipment which generates large amounts of data including, methane concentration, air velocity and barometric pressure. Presently this information is mainly used only to indicate alarm and danger levels of the monitored data for management purposes, however, the potential uses of this data are enormous[1]. This information could be used to good effect within a production/methane emission strategy as detailed in a previous paper[2]. The paper presents a practical application of artificial neural networks to underground methane prediction. Data on methane concentration and coal production has been obtained from an underground coal mine. The data is used in a neural network architecture and forecasts of methane concentration have been obtained. The forecasts are examined and there is a discussion of the potential use of the predictions from neural networks in the field of mining production control.

Jan 1, 1995

By G. I. Karydakis

Geothermal energy is an important energy asset which can play a significant role in providing energy resources to cover energy needs of a country while it can play a primary role in a particular region where it is abundant. Greece is especially rich in geothermal energy. The collision of Euroasiatic and African plates coupled with the strong tectonic tension, particularly in north Greece, resulted in the formation of important geothermal fields of low, medium and high enthalpy. These fields are in the Aegean islands, in central and east Macedonia, in Thrace and in central Greece. This work presents and analyzes information about the drilling activity for exploration and production of geothermal fields of low, medium and high enthalpy in Greece for the past thirty years. The number and type of wells drilled together with the spatial and the yearly distribution are given. Depth data has been analyzed according to the fluid temperatures and to the geological formations. Cost data are presented and analyzed for the total number of wells drilled giving also the cost per meter drilled.

Jan 1, 2006

By Tom Skodack

Mine and tunnel contractors face a complex environment-one in which economic risks are high, operating costs grow ever higher, ore grades are lower or recovery more difficult, and civil construction projects are intensely competitive on a world-wide scale. Within the context of this environment, the risks and rewards of proper machine selection for rock excavation have become proportionately large. Speed, depth and scope of analysis, and extensive supporting information are indispensable in the selection process. Equipment designs and their applications are also myriad and diverse. Several equipment alternatives and excavation techniques may have to be evaluated at once to choose the most cost-efficient approach. The following examples are typical of the current demand for more detailed equipment analysis: • An aggregate supplier starts a new quarry. He knows his targeted tonnage, blasting restrictions, and previous operating costs from other quarries. But he must improve on his old costs. What drill pattern, hole size, and bench height will give lowest cost per ton? How many crawler drills and what type will produce this tonnage most efficiently? • A mine is using a fleet of twin pneumatic ring drills for long hole drilling to initiate their cave. The mine is facing both air shortages and increasing operating costs with decreased efficiency in the ring drill fleet. If they invest in new hydraulic long hole drills, what impact will each drill unit have on production? Each twin drill unit? What configuration gives best operator efficiency and subsequent reduction in manpower? Which configuration gives the best return on investment? • A tunnel contractor is bidding a long straight water tunnel by conventional drill and blast methods. What is the optimum number of drill booms for the tunnel cross section and excavation schedule? How many rounds per day can he achieve? What are his total project drill, blast, and muck costs? In the past, such questions could be answered, but only approximately at best. One good prediction could involve many hours of laborious calculations that had to be repeated each time a new parameter was introduced or an existing parameter changed. In 1980, increasingly complex analysis, coupled with increasing need and quick response times demanded by industry, led Atlas Copco's project department to turn to the computer. New computer programs based on theoretical considerations and three decades of worksite performance data were developed for evaluating mine and tunnel contractors' equipment needs, productivity, and partial or total operating cost calculations for most conventional drill and blast excavation techniques-including shot rock loading and transportation. This Computerized Analysis of Rock Excavation-or CARE-program has since been available to the mining and construction industry. From each program specific results can be pre- dicted, including: • Productivity Calculations-Rock drill penetration rate for a given drill, hole size, and rock type, optimized for the best drill steel life; net machine productivity (drill-out time or drill meters-footage-per shift); total drill round time, including charging, blasting, loading, and haulage; suggested drill pattern, computer printed, including hole size for a given rock drill, rock type, and associated blasting restrictions for either drift rounds or benching applications; long-hole drill meters (ft) per drill shift; breasting down (upper drilling) drill meters (ft) per drill shift; and comparison between continuous loading machine capacity and LHD capacity. • Operating Cost Calculations-Operating costs expressed as cost per drill meter (ft), cost per cubic meter (cubic yard) of excavated rock, and cost per meter (ft) of tunnel advance. These costs may be calculated using as many cost centers as the mine, quarry, or tunneling contractor wishes. Specific operating costs may cover drill rig operating costs only, less capitalization; drill rig operating costs, including amortized equipment investment; drilling and blasting costs; drill, blast, load, and haulage operating costs; long-hole drilling operating costs per drill meter (ft) or per blasted cubic meter (cubic yard) of rock; and loading and transport operating costs. In all the above cases, any number of cost and capacity calculations may be run by simply changing important cost center variables to judge their net effect. Accuracy as a Function of Input Data and the Statistical Data Base Accuracy of a projection clearly depends heavily on the data base from which the projection is drawn.

Jan 11, 1982

By Tim Wolf

The paper "Weld Notch Affects on Pulley and Belt Conveyor Reliability" has done an excellent job of describing theoretical fatigue and fracture mechanics methods used in modern weld design. From this foundation, we intend to further detail areas previously discussed and present new research in the application of these principles to pulley weldment life prediction. Affects of changes in alternating stress range, mean stress, and residual stress have been investigated using controlled laboratory fatigue tests on a pulley weldment. Comparisons between these results, weld codes, and theoretical fatigue predictions will be made and discussed.

Jan 1, 1998

By J. Ragot, D. Maquin, N. Heraud

Acquisition of coherent and representative data about the state of processes remains a major problem of process control. This paper proposes an approach that ensures coherence in measurements on an operational industrial process. The basic technique employed relies on balance equilibration of resource mass flow. An interesting particularity of the set up is the ease with which it can be adapted to check productivity or detect sensor failures. In the case of sensor failure, it suffices to examine the evaluations before and after balance equilibration. The algorithm was tested by means of computer simulation using data from an industrial metallurgical flowsheet.

Jan 1, 1992

By Karl H. Gehring

According to the increasing importance of boom type roadheaders in tunnelling essential problems occuring in the application of these machines are dealt with. Based on a chart including the various stages for decicion finding the excavation method of underground cavities, both the technical limits and economic criteria are discussed in order to determine the range of applicability of roadheaders. Giving examples-the numerous developments in the fields of pick and cutting technology, performance data of boom type roadheaders in hard rock, safety technology and increase in the machines' degree of utilization, research and development of VA is illustrated. Two topic operation examples show partial aspects of the various tendencies of development.

Jan 1, 1981

By Harleigh V. S. Tingley

Investment in the mining industry has increased substantially throughout the world in recent years. So have acquisitions, divestitures, and financial restructurings. The return of outside investors to the industry is welcomed. The trend toward stockholder litigation is not so welcomed. Both have provided the impetus for commissioning outside professional due diligence studies of potential minerals transactions. For a number of reasons, some unique to the industry, evaluation of mining investments is a challenging task for the investor. Investments in exploration prospects and undeveloped properties have a high speculative content. Buyers pay for uncertain future prospects. Alternatively, most developed mining investments are large and long-lived and cannot easily be modified during that life. Even so, to be successful, they must compete in an environment in which their reserves - the source of their profits - are often imperfectly known. And markets, competition, technology, and politics are among the many continually changing factors that affect investment performance. Minerals investment evaluation is further complicated because each minerals investment has its own singular combination of risks and opportunities. Each ore type and each ore body presents different problems in reserve evaluation, mining, and extraction. Each minesite has its own often unique combination of mine, infrastructure, political, environmental, and other risks. And the key requirements for commercial success differ substantially among various minerals.

Jan 1, 1990

By D. Hodouin

The paper reviews approaches to estimate in a real time fashion consistent mass flowrates and assays, using data from the on-stream analyzers and flowmeters of a flotation circuit. Results obtained with one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1996

By M. K. McCarter

INTRODUCTION Mining activity and basic geometry of open pit mines represent major obstacles in geotechnical mapping. Mining creates a constantly changing topographic base which may require corresponding updates of field sheets before mapping can proceed. The rapid pace of mining operations may also threaten removal of important geologic and engineering features before adequate base maps and surveyed control can be established. Maintaining such control during the mapping process is yet another complication. In addition, basic geometry yields nearly vertical outcrops. Access required for direct observation and measurement, essential to conventional plane table or Brunton techniques, may be impossible on such surfaces. Also, nearly vertical surfaces appear fore- shortened in plan view. This reduction in area provides little room for recording geotechnical detail. The difficulties encountered in open pit mapping can be substantially reduced by utilizing a modified form of plane table photogrammetry. This technique employs photographs taken from the ground as the base upon which details are recorded. The information is later transferred to plan maps using the plane table principal of location by intersection (Davis and Foote, 1953). Any change in topography can be accommodated by simply taking additional photographs. Proper spatial representation in plan view can be determined later when updated maps and surveyed control are available. In addition, horizontal photographs from the ground portray vertical surfaces as they are normally viewed thus providing maximum area for recording details. Any detail which can be identified on the photograph can be located correctly even though the actual feature is physically inaccessible. The technique presented in this paper was developed by the author for special applications at Kennecott's Bingham operation in 1970. The procedure was rapidly adopted for general use and has proven to be a practical tool for detailed investigation of potentially unstable areas (Zavodni and McCarter, 1976) and routine geological mapping (Richardson, 1975). Major advantages, other than those mentioned above, include: The speed and accuracy are greater than for conventional plane table or Brunton methods. The photo- graph represents a view from a station at some distance from the area being mapped. This vantage point allows evaluation of possible continuity of structures from one level to another which may not be evident at close range. The photographic base provides a permanent record of the topography at the time

Jan 1, 1977

By J. D. Miller, Z. S. Nickolov

Sum Frequency Spectroscopy (SFS) is a powerful nonlinear optical technique to study interfaces at the molecular level. SFS has one major advantage over conventional vibrational spectroscopic methods, such as infrared (IR) absorption and Raman scattering, in that the method is inherently interface specific. As a result, the spectroscopy of molecules residing in the interfacial region can be probed selectively without any contributions from the molecules present in the more pervasive bulk phases. Analysis of SF spectra can yield information on population, structure, and orientation of interfacial species with several nanometers in-depth resolution. The recently acquired SF spectrometer at the University of Utah opens new possibilities for investigation of interfacial phenomena of great importance for separation technology, materials research, nanotechnology, bioengineering. Its application to studies of liquid/gas, solid/liquid, and solid/gas interfaces will be discussed.

Jan 1, 2004

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By D. R. East

Recent experiences within certain sectors of the international mining industry suggest an underestimation of the environmental risk associated with the design of mine waste management facilities. These experiences show that the technical and managerial challenge of responsible mine waste management is not always fully appreciated. Unfortunately, the image of the mining industry's environmental performance is negatively impacted by a relatively few number of failures. This negative view overrides the many positive contributions made by the majority of mining companies. The fact that these failures continue to occur to this day in both developed and developing countries is indeed remarkable, and indicates a degree of risk-taking approaching unacceptable levels. The design requirements for tailing storage facilities are, in many cases, more demanding than those of conventional water dams, because seepage of fluids which contain dissolved metals may pose a greater threat than the mere loss of water.

Jan 1, 1999

By K. Y. Haramy

A scale-invariant theory of the strength and deformability of rock masses in static equilibrium and at incipient failure is proposed. The theory provides a rationale for designing structures in rock. This paper presents results of experiments conducted by the U.S. Bureau of Mines and theoretical methods to determine and interpret in situ strength of rock masses using the borehole shear tester.

Jan 1, 1995

By R. Hogg

The sedimentation and dewatering characteristics of flocculated slurries are determined by the size and density of the flocs. Studies of the formation and growth of flocs reveal that floc size is limited by breakage of the agglomerates due to shear in the suspension. Floc density measurements indicate that there is an inverse relationship between size and density. This relationship appears to be determined primarily by the nature of the solid particles, especially the size distribution, but it appears that agitation of the suspension can lead to some densification of the flocs, in addition to breakage. It follows that both size and density can be controlled to a significant extent by regulating the physical conditions (agitation, method of flocculant addition etc.) during flocculation. The use of physical floc conditioning to control the sedimentation and dewatering (filtration) behavior of flocculated, fine-particle suspensions is evaluated in terms of its effects on floc size end density.

Jan 1, 1986

By K. Y. Haramy, B. T. Brady

A scale-invariant theory of the strength and deformability, of rock masses in static equilibrium and at incipient failure is proposed The theory provides a rationale, for designing structures in rock. This paper presents results of experiments conducted by the US Bureau of Mines and presents theoretical methods to determine and interpret the in situ strength of rock masses using the borehole shear tester.

Jan 1, 1996

By J. J. Schwoebel

Resource Enterprises Inc. (REI) is exploiting the coalbed gas resource by working in unison with active underground mining operations. At REZ7s pilot project at the Soldier Canyon mine, Carbon County, UT, RE1 has drilled nearly 15.25 km (50,000 ft) of horizontal in-seam and slant boreholes during the initial two years of drilling activity. Produced gas has been sold to a natural gas transmission company on a continuous basis since mid 1983.

Jan 1, 1988

By J. D. Raulerson, R. P. Farias, G. A. Gruber

A flotation process has been developed to successfully treat ore from the Santo Domingo phosphate deposit in Baja California Sur. The ore contained less than 4% P2O5 with quartz, silicates, and carbonates as gangue minerals. Flotation of the low- grade feed in seawater required that the conventional Crago process, comprising direct anionic flotation, deoiling, and inverse cationic flotation, be augmented by an anionic cleaner flotation step, phosphate depression, and a calcite flotation step.

Jan 1, 1988

By B. Karatzoglou

The penetration of sustainability principles in business practices has introduced the necessity for a simultaneous integrated assessment of the corporate economic, environmental and social performances. Continuous technological, political and legal evolutions indicate that Sustainable Development (SD) principles will soon have to be implemented in all sectors of the Greek corporate reality, among them in the Mineral and Mining Industry. However, the ultimate criteria for the evaluation of a company?s performance remain its profitability and its market value. Managers, shareholders, financial intermediaries, all alike, emphasize and base their decisions on the various accounting produced ratios of return (ROA, ROE, ROCE, Residual Value) included, or produced by data found, in the financial statements of the companies. This paper offers evidence that the traditional accounting ratios discourage the implementation of investment plans that aim at improving the environmental performance of companies and therefore can be inadequate and misguiding for SD applications. International studies have consistently traced a positive relationship between the environmental performances of firms and their financial positions. Yet, the fact that investors tend to reward proactive companies by increasing their corporate values is disregarded by the return ratios, which usually set up the basis for management rewards and bonuses. The book value of the firm assets and owners? equity from which such ratios are produced diverges strongly from the real corporate value, defined as the traded amount for the stock of a firm. There is an urgent need for an adjustment of the return ratios so that they can record the positive economic impact of a more sustainable attitude and encourage decision makers towards this direction.

Jan 1, 2003