Search Documents

By G. Vallebuona

Currently, empirical models are used for predicting the hydrocyclone performance in terms of capacity, cut size (d50,c), water split and partition curve. These models, for example those of Lynch and Plitt, have been developed and checked for hydro cyclones with diameters larger than four inches. For smaller diameter hydrocyclones little empirical modelling has been done. This paper reports extended experimental research on small hydrocyclones. For these cyclones, the suitability of existing empirical models has been checked and their accuracy compared. Modifications of the existing models equations are proposed, improving their predictive capability for the small cyclones performance.

Jan 1, 1994

By D. G. Abbott

This paper will describe the development, testing, performance evaluation, and in particular, the utilization for a mining application of revolutionary new mini-disc cutters for use in micro-tunneling and small-and medium-diameter tunneling or mining. It will begin by describing the engineering, testing, and development of rock cutting technology in conjunction with the Rock Boring Laboratories of the Colorado School of Mines. During initial tests, the five-inch cutters were able to penetrate limestone and welded tuff with compressive strengths of 9,000 psi to 24,000 psi. High excavation rates at low thrust and power were achieved with considerably less cutter wear than all previously available conventional discs. Eventually, the discs-with their modified carbide-insert cutting rings, high-load capacity bearings and cantilevered mountings-were able to facilitate the rapid and cost-effective installation of micro-and small-diameter pipes and tunnels in large cobbles and even solid rock, with compressive strengths exceeding 30,000 psi. This paper will also discuss the further development of the machine's cutter head and discs to full-scale site use on a range of tunnel machine sizes and soil conditions, including rock, boulders, and soft ground. Potential mining applications include the installation of tunnels to pro-vide ventilation, emergency escape routes, water drainage, compressed air, electricity, and sand-fill.

Jan 1, 1996

By Richard M. Bennett

Twelve linear test foundations were constructed over an advancing longwall panel in southern Illinois, six were located along the centerline, and six in the maximum tension zone. One footing in each set was a control foundation constructed according to conventional practice. It suffered severe damage. Footings with reinforcing bare and post-tensioning had much smaller elongations, with the post-tensioning preventing cracking of the footing. Footing-soil interface treatments of plastic-on-sand and plastic-on-soil served to reduce damage. The addition of steel fibers to the footing had about the same effect as an interface treatment. Sill plate construction (butt-jointed versus lap-jointed) appeared to significantly affect the behavior.

Jan 1, 1986

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By Curtis A. Pledger, H. Lee Wimmer, I. Michael Gowring

The Upper Diamond Fork Project, as part of the Central Utah Project Completion Act, conveys water six miles from the existing Sixth Water Aqueduct to the Diamond Fork Pipeline. During design, a Value Engineering team proposed a single-tunnel alignment that would be less destructive on the environment and might have a lower life cycle cost than the proposed design of two tunnels connected by two pipelines on steep hillsides. A decision was made to include this option in the bid process as a design-build alternative. The bid for this option was the lowest and a contract was awarded. During the TBM excavation a segment of tunnel wall caved in containing large quantities of water saturated with extremely high levels of hydrogen sul?de (H2S)gas (measured at 380 to 520 ppm in the air). The Central Utah Water Conservancy District (District) in consultation with Obayashi/Clyde (Contractor) quickly developed anew plan to finish the system by incorporating parts of the original tunnel/pipeline concept and re-bid the remainder of the project as a Phase 2 Design-Build contract.

Jan 1, 2003

By A. G. Journel

Few Earth Scientists realize fully the assumptions they are making, willing or not, when pooling into a same histogram data coming from different locations and considering such histogram as an estimate of a probabilistic distribution. First they need the hypothesis of stationarity in space; second the presence of spatial auto-correlations implies that data be unequally weighted according to their relative locations and the degree of spatial continuity of the underlying phenomenon. The novel technique of indicator kriging allows construction of local or global histogram which can be considered as unbiased estimators of precisely defined probabilistic distributions, full account being given to the underlying continuity. Such estimates of local distributions can be used in mine planning for estimation of local recoverable reserves.

Jan 1, 1982

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By Jordan Hoover, Erika Moonin, Chuck George

"In response to a severe regional drought and in preparation for the further decline of water levels in Southern Nevada’s Lake Mead, the Southern Nevada Water Authority (SNWA) built a new intake system to ensure water supply to Las Vegas and its surrounding communities. In 2015, design began on the Low Lake Level Pumping Station (L3PS) that will move the water from this lower intake, ensuring operability of the water delivery system despite these declining lake levels. The L3PS Project includes a 159-meter-deep shaft, a large underground chamber, and 34-each 152-meter-deep, 2.4-meter-diameter drilled well shafts to be constructed in highly faulted and fractured ground. The Construction Manager at Risk (CMAR) delivery method was chosen to facilitate early contractor involvement in the design process to address the significant challenges and risks anticipated on this US$650 million Project. This paper describes the CMAR selection process; the CMAR involvement during design and benefits resulting from that involvement; and the unique collaborative effort among the owner, engineer, program manager and CMAR used to evaluate and select the best design approach, preferred underground construction methods, and coordinated geotechnical baseline report. PROJECT BACKGROUND AND NEED Seven of the United States’ western states rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River Basin. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. Beginning in the year 2000 and continuing to the present, snowfall has been well below documented historical averages and Colorado River flows have diminished."

Jan 1, 2016

By C. B. Queja

Flexible synthetic membrane liners have become a standard facet to copper and gold heap leach pad design. While gold heap leach operations have utilized most types of synthetic liners, copper leach operations have commonly only been lined with polyethylene. The objective of this study was to determine if there are any chemical reasons why other synthetic membrane types could not be used to line a copper heap leach facility. With engineered consideration, the flexible membrane liner under the ore pile serves two purposes. The first provides a near impermeable boundary which aides greatly in the collection of the metal laden process solution. The second advantage to the flexible membrane is the almost non-permeable barrier to benefit increased environmental awareness that has led to an increase in solution containment technology. The Environmental Protection Agency (EPA) has developed a compatibility test for solutions and membrane liners. The EPA Method 9090 is intended for use in determining the chemical effects of a solution on the physical properties of the flexible membrane liner material intended to contain them. Data from these tests would assist in deciding whether a given liner material is acceptable for the intended application.

Jan 1, 1995

By Wilson Blake

The occurrence of rock bursts in some deep mines throughout the world constitutes a severe operational hazard. In addition to endangering the safety of the miners, the rock-burst problem is a major factor in mining economically in deep mines because of the loss of production and expense owing to cleanup and repairs following a burst. Developing means of controlling or eliminating rock bursts has been the subject of intensive research for over 50 years. While much has been learned about the effects of rock bursts, little is known about their basic causes; hence, control measures have been at best only partially effective--attested to by the number and severity of bursts that continue to occur throughout the world each year. In the Coeur d'Alene mining district of north Idaho, the rock-burst problem continues as the silver and lead veins persist at depth. These veins are presently being mined at greater than 7,000 feet below the surface and will be mined to some 10,000 feet in the future. The majority of rock bursts in this district occur in pillars. While pillar bursting has been essentially eliminated in some deep-mining districts by longwall techniques, modification or application of this technique to the thin, irregular, and near vertically dipping veins of the Coeur d'Alene district has not been found to be practical. The creation of pillars is a consequence of the horizontal cut and fill mining method used. Figure 1 shows a vertical longitudinal projection of the silver vein at the Galena mine, illustrating the mining method. Stoping progresses between raises and is carried upward between levels. A horizontal pillar is created as a stope approaches a mined-out level. Recent broad-band micro seismic monitoring of rock-burst-prone stopes by the Bureau of Mines has shown that potential burst zones could be delineated weeks in advance of a burst and that a definite sequence of events took place prior to the occurrence of a pillar burst (1). Hence, time was available for control measures to be effected when a stope pillar reached a critical burst geometry.

Jan 1, 1971

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

By T. S. Golosinski

Use of contractors to excavate, load and haul mined material is widespread in Australia. It is also becoming a common practice in many other countries. The paper reviews current practices in Australian contract mining. Various types of contracts are reviewed, including partnering arrangements and alliancing between the contractor and the mine owner. Applicability of various types of contracts to specific mining situations is discussed, as is their impact on overall mine performance

Jan 1, 1998

In order to overcome some of the deficiencies associated with conventional fine coal cleaning methods, a novel process known as microbubble column flotation (MICROCEL?) was developed at Virginia Tech. This article provides an overview of recent commercialization efforts and in-plant testing of this technology. The results of the in-plant test work indicate that the MICROCEL technology offers several advantages for the upgrading of difficult to clean coals. The test data have also been used to develop guidelines for the design of coal flotation columns and to validate existing scale-up procedures.

Jan 1, 1991

Projections of coal reserves in Central Appalachia are essential for long-term planning in the region. Annual production is declining in some states, such as Virginia, and mineable reserves for the Central Appalachian Coalfield are challenged by difficult geological, mining, and market conditions. In order to project coal mining longevity in this region, interviews with mining companies were conducted to assist in the determination and assessment of technical and economic factors that impact coal seam mineability. This information was applied to seam and coal reserve data developed by state and federal governments. The results were carefully analyzed to determine the effects of various factors on the overall mineable coal reserve base.

Jan 1, 1998

By Yohan Cha, Eun-soo Hong, Gye-Chun Cho

"Rapid population growth and scarcity of space have led many developed cities to bury supply facilities. In line with this, utility tunnels have been employed in Korea since the 1970s. However, approximately 70% of structures were installed more than 20 years ago, in response to the issue of ageing, tunnel enlargement has been proposed. The aim of this study is to investigate geo-mechanical behavior due to tunnel enlargement. Tunnel enlargement methods have been researched to suggest a optimal method. A finite element analysis is conducted to evaluate ground behavior by the expansion of internal space. Vertical displacement and settlement trough width are investigated according to ground stiffness and different enlargement size. It was determined that displacement is affected by the enlargement size and ground stiffness. Based on the deformation results obtained from the numerical analysis, it is possible to predict ground behavior and stability upon tunnel enlargement. INTRODUCTION Various infrastructures such as electric lines, communication lines, gas pipes, and water pipes are jointly accommodated by utility tunnels. These utility tunnels improve the aesthetics of urban areas and help ensure stable supply. The first utility tunnel in Korea was adopted in 1978 and new tunnels are still being installed with the development of new suburb cities. Nevertheless, about 70% of the utility tunnels were installed over 20 years ago and they are still being used through ongoing repair. Moreover, 90% of utility tunnels were installed before 1995. With aging of the nation’s utility tunnels various problems such as concrete deterioration and scarcity of capacity have arisen. As solution, reconstruction has been considered. Reconstruction can enlarge space and improve the performance by replacing existing structures. For reconstruction, two routes have been proposed: underground excavation and cut and cover. In order to avoid traffic problems caused by road occupation and civil appeals during construction projects, underground excavation is the more attractive option. Tunnel enlargement methods have been classified (Seo et al., 2008; An et al 2013) and major considerations during tunnel enlargement have been outlined (Beak et al., 2007). Enlargement construction cases on road tunnels around the world were introduced (Kim et al., 2012) and the deformation curve during tunnel expansion was proposed to investigate the range of protection that should be offered (Kim et al., 2008; Beak et al., 2011). However, tunnel enlargement technology is limited to road tunnels and railway tunnels. Hence, a study on shallow box tunnel enlargement is required for practical application."

Jan 1, 2016

By R. G. Reddy

Viscosities of Feo-SiO2 slags were calculated using the previously developed structural based model. An expression was derived using hole theory and the atomic pair model to relate the NO0 and temperature to the viscosity. The deduced equation n=4.9x10-9 T1/2 NO0 exp (E/RT) poise was successfully applied to predict the viscosity of FeO-SiO2 slags in the composition range of 0.1 < XSiO2 < 1 for several temperatures. The calculated data agrees well with the experimental viscosity data.

Jan 1, 1991

By T. Gonzales

Magma Metals Company operates an Outokumpu Flash Furnace, four Peirce-Smith Converters and two Anode Casting Wheels supported by six Anode Vessels. Process gasses from the Flash Furnace and Converters are treated in a two train/double contact sulfuric acid plant. Sulfur capture for the smelter is +98%. The new flash furnace was commissioned on July 7, 1988 and has processed over three million tons of sulfide concentrate without a major rebuild. Magma has gained unique experience in the operation of the flash furnace at high oxygen enrichments with low off-gas dust loadings. New procedures have been developed to maintain secondary material generation at equilibrium and for maintaining metallurgical control of operating parameters. This paper describes all the procedures, operation control parameters and operating philosophy that has allowed Magma to achieve superior performance.

Jan 1, 1992

By Seokwon Jeon, Ho-Young Jeong

"Various numerical methods have been tried to estimate the cutting forces of a TBM disc cutter. In this study, SPH/FEM coupled method was newly employed to improve the traditional FEM analysis. The disc cutter and rock were modeled by Lagrange and SPH codes, respectively. The numerical cutting test was carried out for representative Korean rocks with different cutting conditions. The results show that the cutting forces obtained from numerical simulation had a good agreement with those from LCM tests, and that applying SPH method to rock cutting model has advantages and improvement compared to traditional FEM method. Erosion criterion and erosion limit were not required to simulate the rock fragmentation process, and the cutting forces from the numerical simulation was more stable and accurate. The results indicate that the numerical simulation can be successfully used to estimate cutting performance of a TBM. 1. INTRODUCTION Various numerical studies have been carried out to accurately simulate the limitations of linear cutting machine (LCM) tests. Numerical modelling methods have advantages comparing with full scale tests in terms of cost and time involved. Many numerical methods have been used to simulate rock cutting process by different cutting tools and the studies are summarized in Table 1.In 2D simulations listed in Table 1, because they do not take account of rolling force and horizontal rolling mechanism of a disc cutter, indenter was selected as cutting tool in their modelling. For these reason, 2D modelling is not suitable for rock cutting modelling using a disc cutter. In contrast, 3D numerical models can take account of the indentation process by thrust force and penetration processes controlled by rolling force."

Jan 1, 2016

By T. Peter Philip, Erich U. Petersen, William J. Tafuri, Donald M. Hausen, Douglas N. Halbe

Scarcely a month goes by that I or someone else at Newmont Mining or Newmont Gold isn&apos;t asked to give a talk on the topic I was asked to discuss today. Investors, financial analysts, geologists, metallurgists, even our government--everybody wants to know what the future holds for gold mining. Well, you&apos;re not going to get exactly what you asked for. Today, I&apos;m prepared to focus primarily not on what the future will bring to us, but rather on what the future will demand from us. More than that, I cannot undertake because it isn&apos;t within my scope to predict how wise and resourceful everyone in our industry will be in the future. What our future will hold, as I see it, will depend on our--and our colleagues&apos;-- responses to these very real demands. Three critical issues stand out in my mind as to what the future will demand of us in the gold mining industry. And these demands will be for: 1. The very greatest of technical expertise and innovation. 2. The highest order of environmental sensitivity and timely accommodation. 3. Planning, planning and more planning. All of these flow inexorably today from the traditional objective of any mining company--or any company in any business, and that is, to make money. Nothing as I see it, should be undertaken by a geologist, metallurgist or even an environmental department, unless the exercises will enhance profits; and nothing may be ignored which can have consequent damage to the bottom line. Thus, the three issues I&apos;ve listed for you subordinate themselves to the objective of making money, although at least in the environmental area, it might seem to some that we can only incur additional costs without even a dollar-for-dollar return. I hope to disabuse you today of any such out-of-date notion. Let&apos;s tackle the first issue-- Technical Expertise and Innovation. Newmont Gold Company this year is celebrating its 25th anniversary of successful and profitable operations on the Carlin Trend. Carlin in 1961, which is when exploration began on the "Trend" by Newmont, actually may share a lot of similarities with Carlin today. They didn&apos;t then know where the gold was and, if they found it, they had one hell of a challenge mining and processing ore at a profit because gold was selling at only $35 an ounce. Today, we know where the current reserves are. But we don&apos;t know where our future reserves lie. Furthermore, we don&apos;t know exactly how we&apos;re going to mine them, and, as everyone here knows too well, we don&apos;t know what the optimum metallurgical treatment is, even if we can find and mine them. And all that despite the abundant level of modern experience and skills within the current generation of mining companies, and the fact that, even taking inflation into account, gold sells at a higher price today than in 1965 when Carlin began operations. But, of course, I&apos;m telling you what you already know.

Jan 1, 1990

By F. A. Renninger

The terms environment and environmental control, when used in today&apos;s context, generally imply to the average individual, something to do with pollution and pollution control. These latter terms, likewise, impart visions of fouled air and dirty water attributable largely to the industrial segment of American society. We have been conditioned, by various means, over the past ten years to equate environ¬mental control with pollution control. We have been trained to think of industrial environmental control programs as efforts conceived only to comply with one or more of the recently imposed pollution control regulations. Almost automatically we; approach consideration of environmental control with a degree of pessimism that is we assume that pollution prompted the control program. It is the purpose of this discussion to demonstrate that environmental control. at least as it exists and has existed within the crushed stone industry, involves far more than simply control or reduction of air and water pollution. It involves a dedication to the enhancement of each of the several "mini-environments" which together comprise the total world surrounding any given crushed stone operation. Environmental control, exercised properly, is an optimistic, constructive, forward-looking, enhancing type of activity. It is a function which has been, and should continue to be, willingly and expectantly undertaken by informed management personnel. In short, environmental control. is an activity from which both industry and society can and should benefit.

Jan 1, 1972