Search Documents

By Bernard Y. Saltie

The White Pine orebody is characterized by a high lateral stress or highly faulted and joined conditions. Because of these difficult conditions roof support has always been a main concern. Mechanical bolts were widely used in the early seventies; however, it became apparent that major improvements in ground control were required if safe operation at White Pine was to be continued. The first step was taken in 1973-1974 with the testing of resin bolting. Record of caves and roof-falls with either type of support demonstrated superiority of resin bolting versus mechanical bolting - Safety was dramatically improved which was the absolute first consideration; however resin bolting was still more expensive than mechanical bolting. In order to generalize resin bolt installation, the second step was therefore to acquire special roof bolters compatible with resin bolting. The machine was to enhance the safety of the operation. This was achieved by the acquisition of the Secoma bolting machine equipped with an automatic bolting turret. Being a "hands off" operation the safety of the operator is total. Using a fixed taped attachment of the drill steel on the chuck a front guide and an automatic regulator torque thrust on the steel drilling in small diameter was possible. Being a fully automatic process only one operator is required per machine versus two operators with the conventional machines. The two main objectives were reached enabling the extension of resin bolting to the whole mine.

Jan 1, 1980

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By Martin H. Stanczyk

In recent, years the demand and consumption of finely ground industrial minerals has substantially increased for such uses as fillers and chemically reactive components. The size, specifications for these types of industrial mineral materials vary to a great extent and depend on the particular end purpose' and on the physical properties of the mineral itself. Size reduction of industrial minerals usually is obtained by conventional crushing and grinding methods. However, some specialized milling techniques have been developed for producing these minerals in extremely fine particle size ranges. During recent years the Bureau of Mines has been investigating an attrition grinding method to produce ultrafine subsieve-size mineral particles. The Bureau developed process, which has been patented,2 comprises the intense agitation of a slurry composed of the material to be ground, a relatively fine granular grinding medium, and a suspending fluid. The process has been shown to be effective for the comminution of kaolin in the particle size range of 2 microns and finer on a batch3 and continuous basis.4,5 This report presents the results of batch tests made to determine the effectiveness of the attrition grinding process for comminuting commercial products of (1) mica, a tough lamellar material, (2) fluorite, a brittle intermediately hard material, and (3) barite, a relatively soft, massive material.

Jan 1, 1967

By Mahmut Altiner

In the present study, the use of horse residue as an alternative reducing agent in the roasting of a low-grade goethite ore containing 17.60% Fe was investigated. Additional roasting experiments were carried out with corn starch and without reducing agent for comparison. Each roasted product was characterized using X-ray diffraction (XRD) and magnetic hysteresis (MH) loops analyses. The optimum roasting conditions (roasting temperature [400, 500, and 600 °C], reducing agent/ore ratio [0.04, 0.08, and 0.12], and roasting time [10, 20, and 30 min]) were investigated based on the Taguchi approach. The magnetic susceptibilities of the roasted sample with the addition of reducing agents were higher compared to that of the roasted sample in the absence of reducing agent. Experimental findings indicate that the horse residue can be used as the reducing agent. Finally, an iron ore concentrate assaying a Fe grade of 62.12% with a recovery of 56.93% was prepared using wet magnetic separation at a magnetic intensity of 0.5 T from the ore roasted under the following roasting conditions: roasting temperature of 500 °C, reducing agent/ sample ratio of 0.08, and roasting time of 30 min.

Jun 3, 2020

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By James R. Miller

Recent experience over extensive areas of the Basin and Range Province has demonstrated the importance of the basin's (valley's) geology and geomorphology in locating large quantities of good-quality aggregate. First, a geologic map depicting basic geomorphic-geologic units in a valley is made in the office from aerial photography. Next, derivative maps are made from geologic maps and field-derived information such as parent rock type, source area and depositional environment, relationship to adjacent deposits, and Quaternary geologic history. Studying the derivative maps leads to selection of test sites for potential deposits of high-quality aggregates. Subsequent field studies provide more detailed information about geologic processes and samples for laboratory testing. Combining all information allows the characterization of aggregate potential of very large areas. Favorable areas can be further tested. This phased approach has proven to be cost effective. The methodology used in mapping and characterizing basinfill deposits is applicable over much of the western United States. Map units were developed by focusing on the predominate geomorphic process, grain size, cementation, and relative age. The resulting functional map units are of use to engineers and planners. This study led to many conclusions, including the fact that the best quality basinfill aggregates are found in selected alluvial fan deposits and Pleistocene lakeshore deposits. The best quality aggregates are derived from Paleozoic carbonate and quartzitic parent materials that can also provide high-quality crushed-rock aggregates.

Jan 1, 1987

By G. F. Revey

Most commercial explosives contain from 70% to 94% (by weight) ammonium nitrate. When some of the explosives end up in shot rock and ore, through either spillage or incomplete detonation, ammonia and nitrates can leach into the ground water. In recent years, state and federal regulators have applied more stringent water-quality standards, particularly at new mines and development projects. When mining conditions permit, bulk ANFO, a mixture of ammonium nitrate and fuel oil, is the explosive of choice. ANFO is less costly than other explosives but it dissolves readily in water. Several case histories in the United States and Canada show a clear connection between uncontrolled losses of bulk explosives and high nitrate levels in mine effluents. Mining companies have tried several approaches to reduce ammonia and nitrate levels in groundwater. These approaches range from controlling explosive losses to treating the mine effluents. In this paper, controlling explosive losses is addressed For both packaged and bulk explosives, guidelines to limit losses during storage, handling and use are described in detail.

Jan 1, 1997

By M. K. Mohanty

Due to inefficiencies of the flotation process, significant effort has been recently provided to develop gravity separators for treating ultrafine particles. As a result, several enhanced gravity concentrators have been developed and commercialized. The Altair Centrifugal Jig is an enhanced gravity separator that provides relatively efficient separations on +25 µm size fractions. An experimental program conducted on -600 µm coal found that the Altair Jig reduced the ash content of the 600 x 44 µm from about 30% to 10% with an 86% combustible recovery value. The pulse water pressure, feed volumetric rate and ragging volume were found to be the key operating parameters affecting the separation performances obtained from the process. An extremely low density cut point of 1.54 and an Ep value of 0.08 were indicative of the high process efficiency values achievable by the Altair jig.

Jan 1, 1998

By Tom Learmont

The importance of coal in solving our energy problems has been widely discussed; the world demand for food requires increased fertilizer production and the minerals to produce fertilizer must be mined. We have seen an explosive increase in the demand for large stripping equipment. It is appropriate that we review this equipment and determine what can be done to improve productivity. While we have used coal mining as an example in the study, much of the discussion will apply equally to other forms of stripping.

Jan 1, 1975

Coal waste materials inhibit direct vegetation establishment due to adverse physical and chemical properties, particularly low water retention and high potential acidity. The Moss # I coal refuse pile is located in Dickenson County, Virginia, and was idled in the late 1980&apos;s with little topsoil resource available for final closure. The refuse was acidic (Total-S = .. 38%; pH = 3.6), black, high (70%) in coarse fragments, and had a low water holding capacity (4.5% in < 2.0 mm fraction). A small plot experiment was established on the refuse pile to evaluate the influence of liming rates (50% and 100% of lime req.) and topsoil thickness (15, 30 and 60 cm) on vegetative growth and leachate quality. Liming and topsoil amendment increased the surface soil pH from < 4.0 to > 6.0 over a two-year period, which resulted in greater vegetative cover and biomass than the control plots. All topsoil treatments resulted in greater vegetative cover and biomass than plots treated with lime only due to improved surface soil physical and chemical properties. A topsoil treatment of 60 cm gave the thickest vegetative cover and biomass yield. Such a treatment, however, would be cost-prohibitive at this location. Application of 27 Mg ha-1 of lime to the refuse surface along with 15 cm of topsoil produced acceptable two-year vegetative cover and biomass, and appeared to be the optimal treatment for this particular situation. Both liming and topsoil had no affect on leachate pH and the electrical conductivity in leachates collected below the plots. This suggests that surface revegetation will have little effect on the quality of water draining through the pile, so long term water treatment requirements may not be reduced by successfully revegetating the pile surface.

Jan 1, 1999

By Donald C. Violetta

During 1963 more than 200 million tons of coal was consumed by the public utility industry. Ash residual, from the burning of this coal has caused disposal problems. In order to prevent air pollution, dust collection systems have been installed to suppress the fine ash emitted from boilers before it is discharged into the atmosphere. The collected ash, called fly ash, must be removed from the dust collection facilities and disposed in some manner, usually at a substantial cost to the utility. Many years ago fly ash disposal was not a serious problem because the demand for power was relatively low and coarse coal was burned on stoker type traveling grate machines. The low burning rates utilized on these grates did not produce large quantities of air-borne coal ash while the mechanics of this system of burning resulted in a clinkered residue of cinders. Both of these conditions resulted in the production of only small quantities of fly ash. As the demand for electricity increased, a method of burning pulverized coal was developed and was introduced to the public utility industry in 1918 at Milwaukee, Wisconsin.1 This method of firing was considered a significant advance in steam electric generation as it (1) permitted the use of coals that could not be economically fired by other methods and (2) has generally resulted in improved efficiency, greater generating capacity and lower costs.2 The utilization of larger generating units using pulverized coal substantially increased the quantity of fly ash which resulted in a&apos; more severe disposal problem.

Jan 1, 1966

By J. D. Miller

"Bastnaesite is one of the important mineral resources for the production of rare earth materials, and it is typically associated with calcite and quartz as gangue minerals. Fatty acid or hydroxamic acid are recommended collectors for bastnaesite flotation. In this research, potassium lauryl phosphate was expected to provide a stronger flotation response for bastnaesite than for the calcite and quartz gangue minerals. Using potassium lauryl phosphate as collector, the results of captive bubble contact angle measurements, zeta potential determinations and microflotation experiments for bastnaesite, calcite and quartz are reported. Greater selectivity for bastnaesite was achieved using potassium lauryl phosphate than using octyl hydroxamate as collector. These results indicate that potassium lauryl phosphate might be a promising collector in the flotation of bastnaesite ores. The computation results of universal force field (UFF) interaction energies for the mineral-reagent interactions are also reported and were found to correlate well with the experimental microflotation results.IntroductionBastnaesite ((Ce,La)FCO3) belongs to the mineral class of semisoluble salt minerals, whose characteristics include ionic bonding and limited solubility in water. Bastnaesite, for the most part, contains the cerium subgroup or the lighter rare earth elements (Zhou et al., 2014). The Mountain Pass deposit in California in the United States and the Bayan Obo deposit in Mongolia in China are the two major deposits of bastnaesite (Azizi et al., 2016; Satur et al., 2016). Calcite and/ or quartz are common gangue minerals in these and many other rare earth deposits (Jordens et al., 2014)"

Jan 1, 2017

By J. Loredo

Wastes related to abandoned mine sites can constitute important potential pollution sources, depending on their mineralogical and geochemical characteristics and volume. Mine waste disposal sites contain a diverse variety of wastes including overburden material and waste rocks, the ore which cannot be economically removed and wastes from the smelting processes when they are accomplished at the mine site. These materials are usually heterogeneous in size, mineralogy and metal concentrations. Asturias, in northern Spain, has an extensive mining history and, in consequence, there are abundant unreclaimed and derelict mine sites with abandoned mines and spoil heaps of different age, morphology, content and dimensions. In these spoil heaps, waste materials are subjected to the intense action of a humid environment, so the instability of sulphides and sulpharsenides results in the production of acid and metal-rich leachates, which are incorporated to surface water or infiltrated through the land reaching groundwater bodies. The mineralogical and geochemical characteristics of the stored materials are key data to evaluate if they represent an environmental risk. Mineralogy and geochemistry of wastes and the particular specific environmental conditions of each site affect the rate of weathering and therefore the metal release. The characterisation of mine wastes is a necessary step in order to establish suitable assessment strategies with the aim of reducing the leaching, transport and widespread of ecotoxic elements from mining wastes to the environment (surface water, sediments, soils and air). As a consequence of the weathering of As-rich mineral phases, high arsenic contents are commonly detected in effluents from mine voids and spoil heap leachates.

Jan 1, 2006

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By Robert C. Freas

The Northeastern United States is the most highly urbanized region in North America. It is also an area with a tremendous appetite for stone products. Within this context limestone has truely become an "urban ore". Its uses extend from traditional aggregate markets to lawn and garden, archetectual, chemical, agricultural, industrial, and environmental applications. This paper looks at both the occurance and uses of limestone in the northeast, and briefly examines changing patterns in consumptive use.

Jan 1, 1985

By M. Robb, S. J. Bate, M. Boisvert

The never-ending quest for gold-bearing ore deposits is a primary industry in Canada, employing people of widely differing expertise. The exploration models for gold deposits are generally geologically complex and the targets have relatively small cross-sectional areas. These problems are compounded in Canada by the minimal outcrop exposure in most mineral provinces and the high percentage of water-covered areas. Naturally the chances of successfully delineating an economic gold deposit are very much greater if all parties involved can act as a team of explorationists constantly confemng amongst themselves particularly as the applicable disciplines generally overlap and complement each other. Three case histories (see Figure 1) are presented to illustrate this philosophy with emphasis placed on the role of the geophysicist in translating the exploration model as defined by the geologist into physically measurable parameters and identifying target areas with similar characteristics. The Conwest-Miminiska property in Ontario is a grassroots exploration play. Additional ore reserves needed to be delineated on the Salmita property in the Northwest Territories. At Laura Lake, near Chapais, Quebec geophysical methods were employed to trace thin high-grade mineral intersections under deep overburden and severe cultural interference.

Jan 1, 1989

By Donald G. Rogich

The concept of initiating a large action-oriented contract, directed toward inherently safe mining systems, was conceived by the U. S. Bureau of Mines in January 1970. At that time we were in the process of establishing research contracts and grants, about 100 of which were let in FY 71 to deal individually with fairly specific technological areas. These projects in the aggregate covered a wide spectrum of health and safety problems. What appeared to be necessary was the creation of a project or program that would provide a focal point for the demonstration of many of the results of this research and also in the action sense culminate with working hardware and systems that could be tested and demonstrated over a fairly long teen. The concept of working demonstrable systems, rather than just a conceptual study, was, felt to be necessary for two significant reasons. In the development of any new system, the translation from concept to working hardware is usually a costly and time consuming process which acts as a deterrent to implementation. Secondly, many decisions in the mining community to change equipment or systems ,are based on first hand observation of the new system, in operational practice, an attitude which is certainly understandable in view of the high capital costs of equipment. The decision was made to procure a single R&D contract which would be aimed at developing underground coal mining systems which

Jan 1, 1972

By Hugo E. Camargo, Amanda S. Azman, Brian Kim

Repeated noise exposure and occupational hearing loss are common health problems across industries and especially within the mining industry. Large mechanized processes, blasting, grinding, drilling, and work that is often in close quarters put many miners at an increased risk of noise overexposure. In stone, sand, and gravel mining, noise is generated from a variety of sources, depending on the type of ore being mined as well as the final consumer product provided by that mine. Depending on the source of noise generation, different strategies to reduce and avoid that noise should be implemented. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the noise profile at three operational surface stone, sand, and gravel mines. A-weighted sound level meter data as well as phase array beamforming data were collected throughout the mines in areas with high noise exposure or high personnel foot or vehicle traffic. Sound level meter data collected on a grid pattern was used to develop sound profiles of the working areas. These sound contour maps as well as phase array beamforming plots were provided to the mines as well as guidance to modify work areas or personnel traffic to reduce noise exposure.

Jan 6, 2022

By Yves C. Lizotte

Although blasting remains the most inexpensive method of fragmentation in hardrock mining, the significance of the costs of blast-induced rockmass damage in terms of mining efficiency and safety is becoming increasingly recognized. There is no straightforward and systematic method of adequately measuring blast damage in on-going mining operations. This paper considers various techniques available to measure blast damage, making particular reference to recent underground hardrock mine studies. It concludes by proposing a damage audit procedure for integration into routine mine production control.

Jan 1, 1996

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999