Search Documents

By D. Bour, C. Nyikos, R. Curtice

Fire in a coal mine can be disastrous on many levels. In most cases, when a fire is detected, mining operations cease and all personnel are evacuated. Underground coal-mine fires are difficult to extinguish, can burn for a long time, and often result in an extended period of lost production. In a worst-case scenario, the mine is permanently sealed and abandoned, resulting in lost jobs, lost natural resources, and possible devastation of the local economy. In some cases, seals placed within the mine to isolate the fire could eliminate the need for sealing the entire mine and the subsequent extended delay in returning the mine to full operation. Previous attempts to place remote seals to extinguish mine fires in active mines have been largely unsuccessful. The West Elk mine experienced an underground fire in early 2000. The fire could not be accessed and extinguished from the active mine workings. A method of constructing seals remotely by drilling boreholes into the affected area was needed to help isolate and extinguish the fire. This paper describes the process by which remote seals were constructed that successfully isolated the fire and provided a means of extinguishing the fire by flooding the area with water. The period of lost production in the West Elk mine was considerably shorter than is typical in similar situations.

Jan 1, 2002

By P. Creevy, P. F. Mousset-Jones, G. Danko, A. D. S. Gillies

The surface heat transfer coefficient is measure of the rate of heat transfer from exposed rock surfaces to the ventilating air. Knowledge of its value is of particular importance to accurately simulate the early stages of rock cooling after the opening of an excavation. A number of theoretical formulae for the calculation of the coefficient are available for use in mine climate simulation. However, direct determination by in situ measurement is preferred. Instrumentation, which has been developed for in situ mine measurement, and experimental procedures involving measurement at varying air velocities, are described. In a major study covering four Australian underground mines, the system has been used to determine surface heat transfer coefficients. A direct relationship was clearly established between the measured surface heat transfer coefficient and air velocity. Comparison is made between experimental results and those previously measured or calculated by others. The relationship established can be described by an equation and holds for air velocities above 0.4 mls. The derived relationship was con- firmed at all mines tested and is independent of geology and tunnel dimensions found in modern mines.

Jan 1, 1991

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

By Larissa Koroznikova, Steve Durkin, Bradley Drake, Michael Tuck

This paper presents the results from the investigation of the application of thermal fragmentation in Australian hard rock underground narrow-vein mining. Two geologically similar samples from an underground narrow-vein hard rock gold mine were collected to obtain a measure of the technology’s ability to recover ore by the creation of large thermal openings to assess the applicability of the thermal method. Particle size distribution showed a higher generation of fine product, − 2 mm, by thermal fragmentation compared with selective blasting by 31%. The Bond work index for thermal ore (12.62 kWh/t) is half to that of the blasted ore value (25.32 kWh/t). The average grindability obtained for the thermal ore sample was greater than the blasted sample by a factor of 2.44, a higher value indicating a decrease in the energy required to grind. The thermal fragmentation method generates product with higher dissolution of gold in cyanide, by 14% for the − 9.5 + 2 mm size fraction samples. Additionally, the thermal fragmentation results in higher production of − 9.5 + 2 mm material by 15 % compared with selective blasting.

The global tunneling industry has many challenges, both technically and financially, with the latter likely to be a significant feature over the next few years. Many industries have ad-opted standard practices in order to overcome specific technical challenges, from which standard out-comes are anticipated. In tunneling, however, every project is unique so standardized practice is not easy. This requires original thinking and being open to adopting new techniques and technologies as they emerge. Sprayed waterproofing is a hot industry topic and a paper recently presented at the North American Tunneling conference not only discussed this methodology for achieving a dry tunnel but also how it can reduce build costs and construction time. Despite their being relatively few ?universal truths? throughout the tunneling industry, there is one opinion that appears to be shared by most in the sector, ?all tunnels leak.?

Jan 1, 2010

By Ray Brainard

The Jollyville Transmission Main will be a 10.5-km- (6.5-mile)-long, 213-cm (84-in.) diameter rock tunnel. The tunnel will pass beneath the Balcones Canyonlands Preserve, which was established to protect two endangered bird species, six endangered cave invertebrates and a threatened salamander. To address the sensitive habitat that the transmission main is to pass through, the city of Austin developed an environmental commissioning (EC) process that brought together environmental engineers and scientists, the city?s project management team and the designer team to work collaboratively to meet the city?s goals of producing a cost-effective design while also protecting the environment. This paper describes the environmental commissioning process and the benefits it brought to the project and environment through some unique environmental mitigation measures to protect this sensitive area.

Jan 1, 2012

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By Joe Roby

Rolling disc cutters are the business end of hard-rock and mixed-face tunnel boring machines (TBMs). Since their first successful employment on a TBM more than 50 years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates are higher and cutter costs are lower than ever before, proving the value of investment in cutter development. Disc cutters are used on a range of tunneling equipment, from pipe jacked slurry micro-TBMs less than 1 m (3.3 ft) in diameter to 15 m (49 ft) in diameter, hard-rock boring TBMs. The geological conditions under which they are employed range from sands and gravels, with several bar of water pressure, to extremely hard, massive rock with UCS up to 420 MPa. Regardless of the type of machine or geology, one thing remains constant: changing worn out cutters is costly. When cutters must be changed in the middle of a tunnel, the contractor incurs the cost of downtime as well as the cost of refurbishing or replacing the cutters. In the case of catastrophic cutter failures, the project can be stopped completely for long periods, and the costs mount up rapidly while tunnel production is at a stand still. Catastrophic cutter failures include the occasion when hard-rock disc cutters are failed in groups (called a ?wipeout? phenomenon) and the operator fails to stop the machine, which results in severe damage to the cutterhead. The cause of this can be either an undetected failed cutter propagating damage to surrounding cutters or operator error in steering. Regardless of the cause, the resulting damage can take days or even weeks to repair. When cutters fail prematurely on EPB or slurry machines in certain geological conditions, it is impossible to evacuate the chamber and, therefore, impossible to get [ ] into the chamber to change the cutters. The solution is frequently an unplanned intervention shaft that must be sunk at great cost. The importance of being able to predict cutter life accurately, and in all geological conditions, cannot be overemphasized. For these reasons, cutters have been developed for specific machine types and sizes, as well as for specific geological operating conditions. Different size cutters are required for different size machines. For example, while 483- and 508-mm (19- and 20-in.) cutters are used on large diameter TBMs, it is impossible to employ cutters so large on a small micro-TBM. Also, the cutter must be designed for the specific geological conditions under which it will be operating. The disc cutter rings required to bore extremely hard rock are the most expensive of cutter rings. However, they provide little advantage in weaker rock formations where less expensive rings will do the job as well. It is important to choose the correct cutter for the machine and the geological conditions in order to get the best balance of cost and risk.

Jan 1, 2009

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By B. Anderson, P. Churak, S. Dewar, A. Johnson, P. Eger

Although vegetation can be successfully established on fine taconite tailings, innovative approaches are needed to reclaim the coarse tailings used for dam construction. Through a series of cooperative projects with various government agencies and industries, EVTAC has been able to develop a unique closure plan. This plan will not only meet current reclamation standards, but also provide mitigation for a disturbed wetland and possibly create a tree plantation in the interior of the basin. By using waste products and exchanging materials, reclamation of the entire basin will be accomplised in a cost effective manner.

Jan 1, 2002

By C. Laughton

Construction of a Deep Underground Science and Engineering Laboratory(DUSEL) is proposed under the auspices of the US National Science Foundation(NSF). DUSEL will provide scientists and engineers with a research facility capable of supporting a broad spectrum of fundamental and applied research deep in the earth’s crust. Research partners are physicists, biologists and geoscientists. DUSEL research calls for the construction of a network of shafts, tunnels and caverns that will provide laboratory facilities at depths of up to approximately 2 kilometers. The Project is still in the planning stages but, the initial experimental program is taking shape and conceptual designs have already been developed at two hard rock mine sites. This paper discusses the overall program and key engineering tasks being developed to support the construction of deep, large-span caverns. These caverns will house a new generation of physics experiments. As currently scoped, the experiments call for the excavation of permanent caverns with spans of up to 60 meters, sited at depths in excess of a kilometer.

Jan 1, 2007

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. William Langer, U.S. Geological Survey, is the chair of the SME industrial minerals technical committees and the vice chair of the technical committee for construction materials. Other technical committee vice chairs include: •Lucy McCartan, U.S. Geological Survey, agricultural minerals. •Steve Herron, Oglebay Norton Performance Minerals, ceramics and refractory materials. •Srinivas Veeramasuneni, U.S. Gypsum, chemical raw materials. •Ismail Yildirim, Imerys, fillers and pigments. •Charles Landis, BPM Minerals, sorbents, filters and process aids. •Ray Harris, Wyoming Geological Survey, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them

Jan 1, 2004

By John Sleavin

As part of the Link Light Rail project in Seattle, WA, work was completed at the Pine Street Stub Tunnel (PSST) in early 2007 for the Central Link project. This tunnel was excavated using cut-and-cover construction within the limits of Pine Street. The stub tunnel provides a turn back via double crossover for light rail trains running in the Downtown Transit Tunnel (DTT), as well as a connection point for the next phase of the project, the University Link (Fig. 1). Designing the new University Link tunnel connection to the existing PSST was a tricky task. The on-site geotechnical conditions, buried obstructions, geometry, requirements for construction and balancing operational considerations and neighborhood stakeholder concerns associated with the recently completed PSST combined to create a uniquely challenging assignment.

Jan 1, 2010

By D. Royston

SAG mill liner development draws primarily on practical experience from SAG milling operations supported by computer-based modeling of charge motion in SAG mills and on established good design practice. Liner design needs to respond to the process aspects of mill liner action that are critical to good SAG mill performance, i.e., the impact of shell liners on the grinding action and of grates and pulp lifters on pulp discharge. In recent years, the trend in large SAG mills has been to use wide-spaced shell lifters with large lifter face angles, primarily to reduce packing and ball/liner damage, and to use larger, hence fewer, mill liner parts to reduce downtime at liner change-outs.

Jan 1, 2007

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By Mustapha A. Raji, Alafara A. Baba, Christianah O. Adeyemi, Aishat Y. Abdulkareem, Rafiu B. Bale, Malay K. Ghosh

The increasing demand for pure aluminum and aluminum compounds of industrial quality from kaolinite ore cannot be overemphasized. Nigeria is one of the African countries endowed with abundant solid mineral resources that have not been sufficiently exploited to assist its indigenous industries. A wide array of applications of pure aluminum and its compounds are available, such as paper filling, refractories, adsorbent, catalysis, and paint additives. In this study, the upgrading of a Nigerian biotite-rich kaolinite ore by a hydrometallurgical route was investigated in oxalic acid media. During leaching studies, the effects of parameters including reaction temperature, lixiviant concentration and particle size on the extent of ore dissolution were examined. At optimal conditions (1.0 mol/L C2H2O4, 75 °C), 92.0% of the initial 10 g/L ore was reacted within 120 min. The dissolution curves from the shrinking core model were analyzed and found to conform to the assumption of surface diffusion reaction, and the calculated activation energy of 33.2 kJ/mol supported the proposed model. The unreacted product (~8.0%) analyzed by XRD was found to contain siliceous impurities and could serve as a valuable by-product for certain industries.

By W. Lin, M. J. McPherson

When a large area of open gob collapses suddenly, a windblast is produced that can cause considerable damage throughout the infrastructure of a mine. In a few cases, the windblast has been accompanied by ignitions of methane and/or coal dust. This paper describes the conduct and results of laboratory tests involving the compression of mixtures of air, methane and coal dust under a falling weight and while allowing controlled escape of the mixture. The transient responses on pressure and temperature sensors were recorded. In addition to an analysis of those records, the paper highlights those conditions in which ignitions occurred.

Feb 24, 1997

Cement in 1975 indeed did operate in an unfriendly environment. World recession, escalating costs, fuel crises, reduced product demand . . . . all led to market conditions detrimental to industry profit margins and investment re turns. During the year plant utilizations fell, break-even points were raised, and competitive moves introduced to move built up inventory levels. A number of cement plants were temporarily taken out of production to help alleviate specific situations. Meanwhile, under resultant financial pressure, several companies omitted dividend payments, changed their top executives, and reorganized and reduced staff overheads. It was a difficult year for cement, yet a much more ominous note was sounded in permanent plant closings. Four more cement operations were shut down in 1975; to date in 1976 we know for sure of three additional plant closings, while rumour has it that at least one more may not be in production by year-end. The somber feature is found within the descriptions of the closed facilities, and in the stated reasons for their being taken out of cement manufacture.

Jan 1, 1976

By Miguel Reyes, Bruce Whisner, Joseph Bickson, Lincan Yan, David Yantek, Justin Srednicki, Nicholas Damiano, Eric Bauer

Built-in-place (BIP) refuge alternatives (RAs) are designed to provide a secure space for miners who cannot escape during a mine emergency. Heat and humidity buildup within RAs may expose miners to physiological hazards such as heat stress. To minimize the risk of heat stress, Title 30 Code of Federal Regulations (CFR), or 30 CFR, mandates a maximum allowable apparent temperature (AT) for an occupied RA of 35 °C (95 °F) (MSHA 2008 [1]). The National Institute for Occupational Safety and Health (NIOSH) has conducted extensive research on the thermal environment of occupied RAs intended for use in underground coal mines. NIOSH research has demonstrated that a fully occupied BIP RA can exceed the AT limit by > 5.6 °C (10 °F) in mines with elevated mine strata and air temperatures (Bissert et al. 2017 [2]). In this circumstance, an RA cooling system could provide a solution. This paper provides an overview of test methodology and findings as well as guidance on improving the performance of a cryogenic air system prototype by optimizing the flow rate, increasing the tank storage capacity, and improving the efficiency of the heat exchanger of the cryogenic system. This may enable BIP RAs to meet the 35 °C (95 °F) AT limit in mines with elevated temperatures. The information in this paper is useful for RA manufacturers and mines that may choose to implement a cryogenic air system as a heat mitigation strategy