Search Documents

By L. A. Baker

The presence of goethite in a hematite ore has been shown to strongly affect the time of heating to the firing temperature. The investigation of spalling of single pellets and of packed beds has enabled free water and goethite spalling to be identified as separate phenomena. In addition, it has been shown that even for an 18 inch deep bed of green balls the free water and goethite drying periods can be considered separately. Based on this observation, a method of predicting production rate and hood temperature profile is presented. The method required knowledge of the ore goethite content, ore grind and the green pellet bulk density. Laboratory results were found to be in good agreement with actual plant practice and have led to improved process performance.

Jan 1, 1972

By Robert E. Gray

The vat leaching operation at the Yerington Mine was started in October, 1953. The original plant facilities consisted of primary and secondary crushing, eight leaching vats, precipitation launders, sulfuric acid plant and the necessary maintenance, warehouse and administrative facilities. By 1961, 35,000,000 tons of oxide ore had been removed from the mine exposing the underlying sulfide ore body. A 5,000 ton per day concentrator was constructed and put into operation to treat the sulfide ore in November, 1961. The original crushing plants were used for both oxide and sulfide ores. By adding a third crushing shift for six days per week, the treated ore was increased from 12,000 to 17,000 tons per day. To balance the oxide and sulfide ore reserves, the concentrator was expanded to 13,500 tons per day in 1967. Again, no additional crushing facilities were added. It was anticipated that the treatment rate of oxide ore would be reduced from 12,000 to 9,000 tons per day. Instead, the addition of two crushing shifts per week, and improved operating procedures, increased the treated ore to 26,500 tons per day, 13,000 tons to the vat leaching and 13,500 tons to the concentrator.

Jan 1, 1975

By Simon E. Rodriguez

This paper presents sulfur isotope data obtained for the deposits and country rocks of the Bailadores and Aroa Mining District, Venezuela. The study is a part of an extensive geochemical investigation of the mineralized belts that has as their aim the elucidation of the genesis of ores. The Bailadores deposits are located at about 600 Km. west-southwest of Caracas, or about 10 Km. southeast of the Town of Bailadores, Merida State (Fig. 1). The mine concession is held by the Ministry of Mines and Hydrocarbons (De Lima I, De Lima II and La Cascade areas). In a straight distance the mine is about 90 Km. southwest of Merida, the capital of Mérida State. From Mérida to Bailadores, through La Victoria and Tovar, it takes 3 hour by car. From Bailadores to the mine site it is about 40 minutes by jeep. The Aroa deposits are located at 4 Km. east of Aroa Village, Yaracuy State, about 220 Km. west of Caracas. It is 83 Km. from San Felipe, the capital of Yaracuy State to the mine (Fig.2). The mine is about 600 m above sea level, situated on the northern foot of the E-W trending Andes. The topography of the mine are shows a mature stage and is somewhat rugged. As the climate is warm and humid, the area is thicky covered with jungle.

Jan 1, 1974

By Martin Langenderfer, Catherine Johnson, Alexander Douglas

Mine haul roads degrade rapidly due to extreme loads on suboptimal construction materials. Unmanned aerial vehicles (UAV) are suited to quantify large-area road-network conditions, such as surface roughness, defects and grade to optimize remediation of poor conditions and reduce overall costs. Mine haul roads present unique challenges, such as material type and edge characteristics, to automatic road detection that often fails, requiring manual road input. This research work proposes a new method using the road center determined by the principal curve of a haul truck’s path. Analysis grids were created from this center line. A dense point cloud from UAV photogrammetry was generated and multiple linear regression analysis was conducted on each individual grid. The root-mean-square error in each grid indicates the surface roughness, and the change of slope between grids indicates the road grade inconsistencies. This method was applied to 26 road sections, and the results were validated by images taken from the truck operator’s vantage point. Critical defects were identified including excessive pothole formation, corrugation, depressions retaining water, and narrowing of travel lane. The results demonstrate this is a valid method of road identification and quantification of road defects at a mine site.

Apr 1, 2024

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, BRADLEY BENNETT, Patrick Zhang

This study level process design represents an economically viable method for extracting thorium dioxide and other rare earth elements from monazite ore. This paper incorporates results from the 2019 capstone project from the honors Design Internship in Green Engineering in Chemical and Biomolecular Engineering. In this activity, senior students in Chemical Engineering at the University of Tennessee (UT) focused on the development and study of a process for the recovery of thorium dioxide and P2O5 from monazite. While not mandated, the process offers rare earth oxides as attractive byproducts. The project focused on recovery of byproducts rather than the creation or addition to waste streams. Additionally, (1) the process economics relied heavily on recovery of rare earth byproducts, (2) thoriumhandling portions of the process could be effectively segregated from rare earth and phosphate handling portions of the process, and (3) thorium and uranium content of waste streams should be carefully managed and eliminated where possible.

May 29, 2020

By B. C. Paul, R. Q. Honaker, K. Ho

Recent research has shown that froth flotation is not effective at treating fine coals (-28 mesh) containing a large portion of middling particles. Due to their relatively large density differences, middling particles can be separated more efficiently using gravity-based processes. The ability of gravity separators to treat fine particles has been limited by the lack of particle inertia relative to the surface drag forces. However, particle inertia can be enhanced by the application of a centrifugal field. A commercial-scale centrifugal Falcon concentrator capable of treating a mass flow rate of greater than 1 tph continuously has been used to evaluate its feasibility for treating fine coal as an alternative to froth flotation. Tests conducted on a -28 mesh fine coal circuit feed have found the Falcon concentrator to be very effective at cleaning the 28 x 325 mesh size fraction. For an Illinois No. 5 coal sample, the ash content was reduced in the 100 x 325 mesh size fraction from about 18% to 8% while achieving a high combustible recovery value of nearly 97%. In addition, the total sulfur content was substantially decreased from 2.6% to 1.7%. The effects of the critical operating parameters on separation performance have been studied and their values optimized.

Jan 1, 1995

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By Z. H. Xie, D. S. He, W. M. Xie

China has rich phosphate rock resources, but with their continuous depletion, the rich ore resources have become increasingly scarce, which makes the exploration of collophane more important. Medium- and low-grade phosphate rock cannot be utilized until their impurities have been removed through mineral processing. However, due to the similar physical and chemical properties of dolomite and phosphorus minerals, the separation of dolomite from phosphate

By Marcus Digre

The autogenous grinding method has been progressively employed in mineral dressing plants during the last 15 years. The term has been used with somewhat different meanings (1), (2), (3). In this paper the author will use it in the most restricted way, for processes where run-of-mine ore (rock) in one step is reduced to a grind product by the action of the ore itself without any other grinding media present. The pebble grinding process where the major part of the ore enters the mill as finely crushed product which is ground further with selected coarse ore pieces acting as grinding media, is not considered autogenous grinding. Processes where a minor amount extraneous media as steel-balls is added to supplement an autogenous mill charge will be called semiautogenous. Other terms need also to be defined. "Mill charge" will be used about the active part of the mill content which performs the grinding, that is the steel balls in ball grinding and the coarse ore pieces in pebble and autogenous grinding. The interstitial nearly finished material is not included in the term "mill charge", and for the wet grinding operations is called the "mill pulp' The term "pebble" will be used for any rounded ore or rock piece in the mill charge whether it is an autogenous or a pebble grinding operation.

Jan 1, 1970

By Paul Kents

The Canadian Javelin Limited Cerro Colorado copper-porphyry deposit in Panama, possibly the largest known copper-porphyry, contains between 1350 and 450 meter elevations, drill proven and probable ore in excess of 3.0 billion tons averaging 0.65% of copper equivalent. The deposit is located in the Central Cordillera Range, straddling the Continental Divide at 1500 meter elevation. Local topography is very steep. Accessibility is difficult, all logistics made by helicopter, and only recently a 52 km. road from the Pan-American highway was completed into the area. The deposit was discovered in 1969, and since then 75 shallow exploratory holes and 98 deep holes, the deepest 1340 meters, totalling 45,000 meters have been drilled. Deep holes were drilled at the corners of a regular rectangular 150 meter grid.

Jan 1, 1975

By C. C. Jobes

Operating large face equipment, such as continuous mining machines, is one of the most basic and most dangerous elements of an underground coal mining operation. The operator usually performs cutting and tramming tasks in a restricted workspace with reduced visibility. During the execution of these tasks, operators often cannot see all of the locations needed to safely operate the continuous mining machine (CM ), which has sometimes resulted in accidents. In an effort to prevent these accidents, researchers at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, examined the continuous mining machine operator?s current information cues, or visual attention locations, so that risk of injury relative to the task, equipment and workplace environment can be evaluated in the future. The eventual goal is to develop interventions to enhance the information cues, and thereby increase the safety and health of machine operators. This paper details the operator interview process, determination of visual attention locations (VALs) and simulation of various mining scenarios.

Jan 1, 2011

For nearly two decades, MINExpo International has held the title to the biggest show in mining. The 2012 MINExpo is expected to be the biggest yet, with nearly 1,800 exhibitors rolling out the newest equipment and services across 12 halls. From September 24 to 26 in the Las Vegas Convention Center, MINExpo will present the newest in everything from automation and robotics to safety and communications equipment to reclamation services, and much, much more. The last MINExpo, in 2008, had nearly 38,500 visitors. The show?s sponsor, the National Mining Association, expects this year will be even bigger, with more than 40,000 visitors over three days. Twenty talks on the issues facing mining today are scheduled for Tuesday and Wednesday mornings, but the real action will happen out on the floor. That?s where ultra haul trucks big enough to carry as much as 363 t (400 st) of rock will be assembled next to underground loaders able to lift more than 20 t (22 st) in one scoop. Caterpillar, Komatsu, Liebherr, Sandvik, Atlas Copco: all the big names in mining equipment will be there. Their massive earthmoving equipment and mining machines are the centerpiece of the show. Preassembly for the largest pieces begins on August 6, 2012.

Jan 1, 2013

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.

By Richard R. Klimpel

The purpose of this paper is to summarize some of the author's experiences in applying population balance models to a variety of industrial grinding circuits. Over 26 separate industrial circuits have been studied in detail during the last 10 years, each unique in its equipment type and layout as well as in the material (s) being ground. The success of the population balance approach during these studies was variable. Fourteen of the circuits were shown to be very amenable to such an approach while the remainder had conditions present that sufficiently violated the standard population balance assumptions so that the analysis was of less than optimal utility. Some discussion of the importance of standard population balance assumptions will be given. It is increasingly becoming this author's opinion that the use of population balance models has its greatest utility in defining logically and cheaply (in contrast to actual physical testing), the relative limits and comparisons of different proposed circuit configurations and changes in equipment types and/or operating conditions. As far as specific quantitative predictions and actual optimization of existing plant performance, the results of applying the population balance approach have been often disappointing and need to be coupled at the plant level with other engineering quantification techniques in order to achieve desired improvements.

Jan 1, 1992

By L. H. Michaud

A mining company plans to extend its surface coal-mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accountings for the site shows an overall Neutralization Potential to Maximum Potential Acidity Ratio (NP:MPA) of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to be mined. If traditional dragline-mining methods are used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of acid mine drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. To prevent the formation of AMD, the company has proposed to mine the area using truck-shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, amine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil to achieve an overall net alkalinity in all spoil areas. Therefore, mining this site should not result in the formation of AMD.

Jan 1, 1996

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

In order to address the difficulty of accurate segmentation of froth images of different sizes, a method of froth image segmentation based on highlight correction and parameter adaptation is proposed. First, a machine vision system on a single-cell flotation machine is built to collect froth images. Homomorphic filtering is used to improve the uneven brightness and shadow of the images. Fuzzy c-means (FCM) clustering is then utilized to classify similar highlights that belong to the same froth. After Otsu threshold segmentation, a parameter-adaptive morphological operation is used to extract the marker points and edge bands and correct the froth edges in the original image. Finally, the modified image is filtered by morphological reconstruction, and the highlight mark is used as the local minimum point for watershed segmentation. Three sizes of froth images are segmented in comparative experiments. The results show that the proposed method is suitable for the segmentation of froth images of different sizes. The position of the extracted segmentation line is close to reality, with average over-segmentation and under-segmentation rates for froth images of 2.6% and 6.8%, respectively. The froth image segmentation performance is stronger than that of the other methods examined.

By D. L. Langhans

Platinum-group metal (PGM) converter matte from the Stillwater Complex, MT, was subjected to chemical and biological leaching in an effort to upgrade the matte by decreasing the Cu and Ni content. Copper and NL extractions were optimized in a two-stage chemical leach. Atmospheric pressure sulfuric acid leaching removed over 90 pct of the Ni and Fe in the first stage, while 95 to 98 pct of the Cu was removed is the second stage using an acidified cupric chloride leach. This two-stage leach, followed by an elemental sulfur removal step, decreased the weight of the matte by 90 pct. The combined Cu and Ni content was reduced from 65 pct to less than 20 pct, while the PGM content was increased from less than 2 pct to 26 pct. Biological oxidation using Thiobacillus ferrooxidans also proved to be an effective method for removing Cu and Ni. Over 90 pct of the sulfide was oxidized and 99 pct of the Cu and Ni were solubilized, leading to a 60 pct reduction of sample mass during the 17 week bio-oxidation of the Stillwater converter matte. The final residue, after removal of jarosite that accumulated during bio-oxidation, contained less than 3 pct combined Cu and Ni and 6 pct MM.

Jan 1, 1993

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By Scott L. Burrill

In the past 100 years in the mining industry, many references are made to the "Widow Makers", 'Miners Con" and many other derogatory names related to physical hazards. They reflect the lack of understanding of the problem facing the early day miner. Workers were enticed, in some cases, to take a chance against a medical question mark that could not be explained by the doctors of those early days. The optimism of the mining man and the challenge of work led him to believe that the physical results could not apply to himself and only applied to some of his fellow workers. Much of the time, to his dismay, he found that he had lost to the game of chance. As medical knowledge improved and mining management began to understand the effects of conditions in the mines and beneficiation plants, steps were taken to alleviate or eliminate the health hazards that were present, The organizations engaged in mining that did not take an active interest in employee health found themselves to eventually be placed in the position of being forced to take action by Federal and State legislation. We find ourselves in the 1970's on the threshold of a new era where the general public is concerned vociferously about "their" environment and the industry feels the governmental controls more strongly than ever before. It can be said that in the past 100 years we have advanced from the "Widow Makers" of the 1870's to the "Retirement Makers" of today. The difficulties of the early days in underground mining were of times compounded in the beneficiation plants above ground. As late as the 1950's some crushing and milling installations in the United States were operating under environmental conditions that complied to the then existing legislation but were below the health level sought by conscientious management. The Mission Concentrator Crushing Plant was designed in 1959 and placed in operation in July, 1961. In the past ten years the crushing plant has been continuously complimented by technical people, government inspectors and casual

Jan 1, 1971