Search Documents

By D. R. Hardman, J. W. Oberholzer

Based on information supplied by South African collieries to the Coal Mining Laboratory of the Chamber of Mines since 1978, the paper outlines the general performance of the continuous miners used and gives the results more-detailed studies of the cutting, loading, and transportation processes. On average, the continuous miners produced coal at a rate of 76 t per operating hour, which, at an average machine availability of 67 per cent, resulted in a production of 51 t per total hour. The cutting rates varied between and 250 t/h but, owing to machine and system inefficiencies, the overall production rate varied between 92 and 48 It is concluded that, if the collieries concentrated on improving their machine utilization procedures and operating practices, they could increase the overall production from their continuous-miner sections.

Jan 1, 1987

By R. C. Urquhart, W. P. Channon, D. D. Howat

The mode of current transfer between electrode and slag in the submerged-arc furnace . by W. P. CHANNON, B.Sc.(Eng.)(Student Member), R. C. URQUHART, M.Sc.(Eng.), ;'h.D.(Visitor), and D. D. HOWAT, B.Sc., Ph.D.(Fellow) An account is given of a laboratory experiment in which the resistivity of a primary slag like those produced in the manufacture of high-carbon ferrochromium was measured at current densities typical of operation in a submergedarc furnace. It was shown that the current flow from graphite elec trode to molten slag obeys Ohm's Law when electrode current densities are less than 12 A/cm". At higher current densities, arcing occurs from the electrode tip to the slag, causing an imbalance in the rate of heating in the furnace burden.

Jan 8, 1974

By B. Kenealy

A typical deep shaft is President Steyn No. 2 in the Free State, where 9 tonnes of ore are hoisted at about 15 metres per second from 2378 metres below surface. The skips and attachments each weigh 7 tonnes and they are connected by 43 tonnes of rope, so that to hoist the 9 tonnes of payload, a total of 66 tonnes is accelerated from stand still to 55 km/h for each cycle, using an average of 3185 kilowatts of power in the process. The cycle time for the hoisting is 3.22 minutes. The peak power consumption is 6954 kilowatts, which determines the size of the motor used. Is this the right approach? Are larger skips moving at higher speeds the answer? Is there another way?

Jan 1, 1996

By M. A. von Below, I. C. Robinson

A mineral economic analysis of South Africa's mineral-beneficiation industry, comprising both economic theory and case studies, suggests that the domestic market has proved to be a more effective vehicle for promoting the establishment of advanced beneficiation projects than the availability of domestic raw materials. Although the domestic market plays an important role in the promotion of beneficiation by providing a secure outlet for sales, its most vital role is in the development of technological and marketing know-how that may give South African beneficiated products the competitive advantage required to penetrate export markets. The real wealth of a country lies primarily in the skills of its people rather than in its natural resources, and the domestic market plays a pivotal role in the development of these skills.

Jan 1, 1990

By A. H. Mokken, G. K. I. Blendulf, N. R. Cowin, K. A. G. Blendulf

A study, by continuous monitoring of particle size in the cyclone overflow, of factors influencing run-of-mine mill performance by A. H. MOKKEN, B.Sc. (Eng.) (Rand) (Fellow), G. K. I. BLENDULF M.Sc. (Stockholm) (Member), K. A. G. BLENDULF, Dipl. (Min & Met) (Visitor), and N. R. COWIN, B.Sc. (Min. Tech.) (Visitor) An account is given of an investigation of the use of a continuous particle-size monitor - the PSM-IOO. The monitor system, in addition to showing marked variations in grinding fineness over short periods of time, particularly after stopping and re-starting the feed to the mill, has indicated weaknesses in accepted mill operating practice. The main potential of the system is the opportunity it has provided for almost complete automation of the milling circuit.

Jan 5, 1975

By R. L. Paul

Although it is often said that South Africa does not have suitable deposits, or the potential to develop mines on a small scale, a recent survey by the Chamber of Mines1 showed that, out of a sample of 641 producers, 41 per cent had between 10 and 19 employees, and a further 29 per cent had between 20 and 29 employees. This goes to show that minerals-related small, medium, and micro-enterprises (SMMEs) do exist, and can play an important role in the development of rural industries in South Africa. Nchaka Moloi of the Department for Mineral and Energy Affairs defined the various categories of SMMEsas shown in Table I2. An enterprise could be placed in a certain category as long as two of the variables, employees, capex or production applied.

Jan 1, 1997

By P. J. How, T. O. Hagan, M. F. Handley

Inelastic deformation of highly stressed rock in deep mines needs to be quantified in both time and space. Since most deformation occurs by shear, continuous monitoring of discontinuities in the rock from boreholes holds promise. The casing. Al interpretations of shear movements are based on a simple relation between shear displacement and the resulting change in tilt of the sensor. A prototype has been constructed and has undergone laboratory trials with satisfactory results. Underground trials will commence shortly. The instrument as designed has the potential for other applications, both in the civil-engineering and mining industries. paper describes an instrument that is both cheap and reliable, and capable of monitoring such shear movements continuously. The principle of operation is based on two capacitive gravity sensors mounted orthogonaly to each other in a sealed aluminum

Jan 1, 1988

By A. V. L. Narasimham

The practice of refractory lining in Fe Cr furnaces is purely based on the behavior of various refractories used in different parts of the Furnace at elevated temperatures. The choice of the pattern of lining is mostly done on traditionally based concepts. Refractory Lining of a furnace is the most crucial enabler for operational excellence for Ferro Alloys production. During the last few years, no major technological change has taken place in ?Refractory Lining Management?, only freeze lining concept is becoming popular. Many ferro chrome furnaces today, have the refractory lining problems especially at tap holes, resulting in shutdowns and production losses. The author with his experiences for the last 37 years in furnaces of all sizes tried to attempt to investigate into the reasons for premature failure of lining.

Jan 1, 2007

An International Ferro-alloys Congress, arranged by the Ferro Alloy Producers' Association of South Africa, the South African Institute of Mining and Metallurgy, and the National Institute for Metallurgy, will be held in Johannesburg, South Africa, in April 1974. The technical programme, occupying five days, will cover the following topics in relation to all ferro-alloys: 1. Burden preparation, blending, pelletization, handling, reducing agents. 2. Electric smelting furnaces-design, operation, management,- smelting optimization, shop practice, refractories. 3. Mineralogy, reduction behaviour, smelting reactions, slags. 4. Automation, Pollution control. 5. Applications, trends in comsumption, trends in composition specifications. There will be no parallel sessions. Papers in the above topics are invited; review papers will also be welcome. Proposed titles and abstracts in not more than 200 words should be submitted before the 30th of November, 1972, to The Chairman, Programme Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa. The abstracts will be considered during January 1973, and papers accepted for the Congress must be submitted in final form before the 31st of July, 1973. The proceedings of the Congress will be published as a special volume. There will be a series of post-Congress tours to ferroalloy plants and other places of both technical and scenic interest. A full ladies' programme will be arranged. The First Circular, giving further details, can be obtained from: The Secretary of the Organizing Committee, INFACON 74, Private Bag 7, AUCKLAND PARK, South Africa.

The following comment has been received from Mr A. D. Osche* on the above paper, which was published in the Journal in October 1977 (vol. 78, no. 3, pp. 51-62). Obituary: T. K. Prentice The Institute records with deep regret the death on 30th January of its senior surviving Past President, Mr Thomas Kennedy Prentice, at the age of 83. Book reviews R. A. Rich, H. D. Holland, and U. Petersen. Hydrothermal uranium deposits. (Developments in Economic Geology, vol. 6). Amsterdam, Elsevier Scientific Publishing Co., 264 pp. with 77 illustrations and diagrams, 30 tables. U.S. $34,75. M. David. Geostatistical ore reserve estimation. Amsterdam, Elsevier Publishing Company, 1977. 364 pp. World mineral industry The Australasian Institute of Mining and Metallurgy is celebrating its sesquicentenary in 1979. A conference will be held in Perth from 13th to 18th August, 1979, as part of the celebrations, the theme being 'Australia's Role in the World Mineral Industry'. Engineering teaching staff UNESCO has extended its technical assistance to the Venezuelan government in the training of engineers to suit the rapidly developing economy of the country. UNESCO vacancy Vacancy for a post of expert under the UNDP. (1) Title of post: Expert in metallurgical engineering. (2) Duty station: Instituto Universitario Politecnico of Ciudad Guyana (Venezuela). Shell Design Awards The annual Shell Design Awards, organized by the Design Institute and sponsored by Shell South Africa (Pty) Ltd, focus attention on achievements in South African design.

Jan 1, 1978

By S. Budavari

The effects of shaft pillars left in deep-level hard-rock mines during the extraction of tabular deposits were studied some time ago, resulting in the formulation of design principles and procedures, which have been used with success in the design of shaft pillars in the deep-level gold mines of South Africa. The method has not yet been utilized in the design of shaft pillars in shallow and moderately deep hard-rock mines. The purpose of the present study was to remedy the situation since a great number of deposits are worked at those depths. The object of this paper is to present governing equations for the components of stress and differential movement as derived by use of an elastic model. The pillar is taken to be circular in the plane of a horizontal deposit. On the basis of the numerical results obtained, a study was made of the distribution of the vertical strain and tilt along the axis of the shaft, and of the vertical stress along the shaft and across the pillar. In every case investigated, the most adverse geometry was taken into consideration. By use of an empirical criterion and the results of some in situ observations, the determination of pillar dimensions and differential displacement components for South African gold-mining conditions is demonstrated. Pillar dimensions for shallow and moderate depths are compared with those accepted for deep-level conditions.

Jan 1, 1986

By M. A. de Ruijter

Bracken Gold Mine ceased mining operations during February 1993. The clean-up of the gold plant, which had already commenced in September 1992, was completed in January 1994. The mine had been in production since early in 1962 but, because of a decreasing ore reserve, increasing working costs, and a relatively low gold price, closure had become inevitable. The closure had been under consideration since August 1983, when the first estimate was made regarding the amount of gold that could be recovered from the clean-up operations. Until that stage, it had been accepted that Bracken would conform to the commonly accepted idea that 0.25% of the total gold produced by the plant would be recovered during the clean-up operation. This idea was dispelled when the initial estimates indicated that the gold recovery would vary between 0.049 and 0.095%. The actual figure realized was 0.036%, showing that there is no generalforl1ula for the calculation of the amount of gold to be recovered from such clean-up operations. During the clean-up operation, Bracken became an unexpected contributor to the State's Reconstruction and Development Programme by having al the mine and plant buildings purchased and converted into a community development centre. This shortene4 the time available for the clean-up, and several of the buildings remained intact. However, the foundations and sub-soils had been sampled extensively, and it is considered that no recoverable gold was left behind.

Jan 1, 1996

Actual observations of rockburst damage, together with some theoretical considerations, strongly suggest that conventional approaches to the design of tunnel support are inappropriate where there is a significant seismic risk. The present widely used support systems, which are based on stiff, fully grouted re-bars, are inadequate where rock displacement velocities exceed 1 m/s. It is shown by means of a simple conceptual model that yielding of the support elements is essential to ensure their survival when they are subject to the high strain rates typical of severe rockbursts. The model proposes that the total load in the element is an impulsive tensile force imposed and sustained by a single 'tributary' block ejected from the tunnel wall. The stability of the system is determined from a comparison of the kinetic energy developed by the block with the energy of deformation absorbed by a grouted steel tendon. A novel test procedure was developed for the validation of this approach, and for an examination of the energy-absorbing capacity of stiff and yielding tendons. The results of an initial series of tests showed that the recently developed cone-bolt is an effective yielding device. It absorbs twenty times more impulsive-load energy than is consumed by the complete fracture of grouted re-bar of equivalent strength, and it remains totally unscathed. Importantly, the results demonstrate that the ejection model is not merely an explanatory concept, but can be used as a representative and valid design method.

Jan 1, 1994

By E. -U. Reuther

To improve the climatic environment underground the German coal mining industry has installed refrigerators with a capacity of 300 MW cooling power. One third of this total is accounted for by central refrigeration plants with more than 5 MW capacity. The central refrigeration comprises three stages: mechanical cooling, transport and distribution of chilled water via pipelines and exchange of heat in the air coolers. Of these three stages only the mechanical generation of chilled water has been resolved satisfactorily. Transport (including distribution) and exchange require further technical research. The Mining Institute of the Aachen University of Technology has done extensive studies on this subject, concentrating on controlling the flow of chilled water according to demand in the mine. Additionally, the favourable exchange in the air coolers is taken into account. The studies are based on a model mine which simulates the conditions in deep coal mines in Germany. The simulation program represents firstly the condition of the mine air at the location of the air being cooled, then the heat exchange in the air cooler itself, and finally the transport of the chilled water from the central refrigerator to the consumer. The program also reproduces the seasonal and operational changes in conditions of mine air as well as different air cooler designs. A regulated distribution of chilled water is also suggested. Finally, estimations of costs can be made as an aid for further planning.

Jan 1, 1987

By Y. -H. Chang, Y. -J. Jou, T. -S. Ueng, I. -H. Peng

In order to systematically study the size effect on the shear strength of rock joints, this study used the computer-aided-manufacturing system to reproduce the artificial rock joints for saw-toothed joints, Barton's standard joint profiles of JRC = 4~6 and 18~20, and natural rock joint profiles. We divided, enlarged, reduced, and assembled these joint profiles to obtain joint specimens of various sizes ranging from 75 mm to 300 mm in length. The shear strengths of these joint specimens were tested under different normal stresses using a direct shear test apparatus. The surface conditions of the joints at failure were also examined. The size and geometry effects on the shear strengths of these joints of various sizes and configurations were evaluated based on the test results. Um die künstlichen Trennflächen für reguläre dreieckige Trennflächen, Bartonsche standardmäßige Querschnitte der Trennflächen von JRC = 4~6 und 18~20 und natürliche Querschnitte von Trennflächen wiederherzustellen, benutzt diese Forschungsarbeit das Computergestützte-Erstellungssystem, damit die Maßstabswirkung auf die Scherfestigkeit von Trennflächen systematisch untersucht werden kann. Die Querschnitte werden geteilt, vergrößert, verkleinert und zusammengesetzt, um Trennflächenproben in Längen variierend von 75 mm bis 300 mm zu erhalten. Die Scherfestigkeit dieser Trennflächenproben wird unter unterschiedlichen Normalspannungen mit einem Direktscherversuchsgerät getestet. Die Querschnittszustände der Trennflächen bei Versagen werden ebenfalls untersucht. Nach den Untersuchungsergebnissen werden die Maßstabs- und Geometriewirkung auf die Scherfestigkeit dieser Trennflächen verschiedener Größen und Konfigurationen ausgewertet. Pour étudier systématiquement l’effet de la dimension des fractures des roches sur leur résistance au cisaillement un système de creation de fractures artificielles à l’ordinateur a été employé. Des fractures artificielles triangulaires, profils de fractures de Barton avec JRC = 4~6 et 18~20, et profils de fractures naturelles ont été reproduits. Les profils des fractures ont été arrangés de manière à obtenir des échantillons de longueur entre 75 et 300 mm. Une boîte de cisaillement a été utilisée pour étudier la résistance des fractures au cisaillement, sous plusieurs conditions de contraintes normales. Les conditions superficielles des fractures après rupture ont été étudiées. Les résultats de ces essais, effectués sur plusieurs échantillons de dimensions et configurations variées, ont contribué à établir l’influence des dimensions et de la géométrie des fractures sur leur résistance au cisaillement.

Jan 1, 2003

By S. Wakita, K. Aoki, Y. Mito, K. Date

It is of great importance to prevent a leakage of hazardous substances from underground storage plants, because this certainly leads to a fatal disaster for human societies. Therefore, effective grouting system needs to be developed, which can inject cement grout into low-permeable rock masses. Authors have carried out a series of laboratory injection tests using a fracture model and field tests in low-permeable rock masses. In these tests, not only was the superiority of dynamic grouting confirmed, but also the relationship between grouting-efficiency and injection parameters was investigated. In this paper, the results of laboratory injection tests and field tests together with theoretical approaches to them are mentioned. L’empêchement de la fuite des substances dangereuses des galeries de stockage est un traitement très important pour protéger la société humaine contre la comtamination catastrophique. Par conséquent, un procédé d’injection efficace doit être mis au point, qui peut injecter du coulis de ciment dans le rocher ayant une perméabilité basse. Les auteurs ont effectué une série d'essais d'injection en laboratoire en utilisant un modèle de rupture et d'essais sur le terrain dans le rocher ayant une perméabilité basse. Dans ces essais, était non seulement la supériorité du l’injection dynamique confirmée, mais aussi le rapport entre l’efficacité de l’injection et les paramètres d'injection a été étudié. Dans cet article, les résultats des essais d'injection en laboratoire et des essais sur le terrain ainsi que les méthodes théoriques pour les essais sont mentionnés. Es ist wichtig, Durchsickerns gefährlicher Substanzen aus unterirdischen Lagerstellen zu verhindern, weil dies für die menschliche Gesellschaft unter Umständen zu verheerenden Unfällen führen kann. Daher muß ein effizientes VerfugesSystem entwickelt werden, welches erlaubt den Mörtelschlamm in wenig durchlässige Felsenmassen einzuspritzen. Die Autoren haben eine Serie von Laboreinspritzungsversuchen mit einem Bruchmodell und Feldversuche an wenig durchlässigen Felsenmassen durchgeführt. Diese Versuche zeigten nicht nur die Überlegenheit des dynamischen Verfugens, sondern wurde dabei auch das Verhältnis zwischen Verfugen und Leistungsfähigkeit sowie den Einspritzungparametern untersucht. In dieser Studie werden die Ergebnisse der Laboreinspritzungtests und die Feldversuche zusammen mit den entsprechenden theoretischen Ansätzen erläutert.

Jan 1, 2003

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

The first neutrinos in nature ever detected by man were "caught" in a unique laboratory some 3 km (over 2 miles) underground in one of the world's deepest mine shafts at East Rand Proprietary Mines (ERPM), Boksburg. Only 100 m from where gold is being mined from the rock face a small team of South African and American physicists work on one of the most fascinating and important fundamental research projects that is currently exciting the imagination of the scientific world. Neutrinos are sub-atomic particles just as are protons, neutrons and electrons, but they are unique in that they have neither electric charge nor mass. Cosmic neutrinos travel at the speed of light and penetrate stars and planets. Even a million kilometres of solid lead would not provide a satisfactory shield against them. Stars are believed to "burn" by means of nuclear reactions which produce enormous fluxes of neutrinos. The sun, for example, illuminates the earth with visible light, but also bathes it with neutrinos. After World War II, two American physicists, Profs Frederick Reines and Clyde Cowan, experimenting at a large nuclear reactor, succeeded in obtaining direct evidence of the existence of the laboratory-produced neutrino. It then became very important to establish whether neutrinos also existed in nature. This knowledge would lead to a greater understanding of the forces of nuclear physics, of the behaviour of nuclear particles and, indeed, is also relevant to astrophysics. From the start it was clear that the search for "natural" neutrinos would be difficult. Questions which arose were- * how could they be traced if they were without mass or electric charge? * how could other nuclear particles be screened off? * could these not be wrongly detected, or even prevent accurate detection of neutrinos? Neutrinos were known to be produced along with charged particles, by the reaction of primary cosmic rays with the constituents of the atmosphere. It was also known that when the neutrinos collided with matter, they themselves produced the same type of charged particle which could be detected if the unwanted charged particles from the atmosphere could be screened off. What was needed, therefore, was a laboratory where the particles produced in the atmosphere could be screened out, yet which would receive and detect the particles produced by the neutrons' collision with the matter (solid rock) in the vicinity of the laboratory. This meant that scientists either had to build a laboratory with an enormously thick lead shield for their detection work. . . or they could go as near as possible to the centre of the earth where only charged nuclear particles of the very highest energies could penetrate. ERPM was clearly the most suitable place in the world where so effective a "neutrino trap" could be set. Under more than 3 000 m of solid rock the apparatus for detecting neutrinos is well shielded against unwanted nuclear particles produced in the cosmic radiation which can reach the laboratory only in a steeply vertical trajectory. Other particles are easily stopped by the great thickness of rock. The air-conditioned laboratory is at one end of a 150 m long tunnel, 2,5 m high and wide, blasted from the rock. The electronic recording equipment is housed here, while the rest of the tunnel is filled with the detection system. When a charged particle passes through a detector element, it produces a minute flash of light which is recorded and which triggers a flash-tube array. This then defines the trajectory of the charged particle, which is also recorded on film for analysis. So far 82 neutrinos have been detected, 50 at the present level and 32 at a higher level, and the findings have borne out the physicists' theoretical expectations. In this joint project Profs Reines, J. P. F. Sellschop, Director of the Witwatersrand University's Nuclear Research Unit and M. F. Crouch of the Case-Western Reserve University of Ohio are the Chief Investigators. This unique endeavour has been made possible by financial support from the US Atomic Energy Commission, the University of the Witwatersrand and the Chamber of Mines of South Africa, as well as by the cooperation of the management and men of ERPM.

By T. Szendrei, S. Tose

The fracturing and movement of rock that occurs in the vicinity of a stemmed borehole charge in open pit mining operations are described by examining the effects of the emitted stress waves – shock and elastic – and the expansion of high-pressure detonation product gases. Three principal modes of momentum transfer to fractured rock are identified, all linked to gas expansion work. This work can be delivered radially (burden), axially (stemming), and in the collar zone (cratering). Flyrock is generated under unusual combinations of blast parameters and rock properties. Although infrequent and seldom predictable, the generation of flyrock can nonetheless be interpreted and modelled in terms of the principal mechanisms of rock projection described in this study. The physical processes underlying these principal mechanisms are identified and will permit the development of predictive models for flyrock velocities.

Dec 13, 2023

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014