Search Documents

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

Elongates are commonly used as stope support in South African gold and platinum mines. To evaluate the effect of the inherent strength, stiffness and yield variability associated with elongates, a statistical method is presented which addresses and quantifies the support performance at various levels of certainty. The analysis, which is based on a normal distribution, makes use of force-deformation curves determined from multiple laboratory compression tests on the same support type. The applicability of the method is illustrated making use of actual performance capabilities of various types of elongates. In order to ensure a high probability that support units installed underground exceed the standard support performance curve established by means of laboratory tests, the statistical mean of a suite of tests based on the same support type is downgraded. The ?correction factor? is a function of the mean and standard deviation of the test data, as well as the sample size of units deemed to control the local rock mass stability. It is shown that downgraded performance curves based on a high probability (90 to 95percent) of support units exceeding this performance level are suitable to ensure that the design of support systems will in variably meet the design criteria. In the highly discontinuous hangingwall rock mass typically associated with intermediate- and deep-level mining operations, the interaction between adjacent support units is comparatively limited (at the support spacings commonly used). Therefore, the appropriate sample size (n) of the support units controlling the local rock mass stability should be n= 1. In shallow mining conditions, sample sizes of up to n=5 may be warranted, depending on the spacing of joints and other discontinuities in the hangingwall.

Jan 1, 2001

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By K. L. Morton

Groundwater and associated pore pressure represent elements that can have a negative impact on surface mining and slope stability. Groundwater flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely, if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data were available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

By V Kveldsvik, N Ragvin, T Eiken, G Grøneng, G V. Ganerød

Catastrophic rock slope failures have caused destructive tsunamis in Norwegian fjords. At the Åknes rock slope the tsunami generating potential is large due to the potential large volume involved in a possible catastrophic failure. Widening of the upper crack has been recorded since 1986, and in recent years, a quite extensive investigation and monitorin campaign has been conducted. Data from some of these investigations are presented and analysed with respect to a preliminary evaluation of the stability of the slope.

Jan 1, 2006

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By B. Solar Menéndez, M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza

The analysis of subsidence due to the opening of an underground void (mining, water exploitation or civil works hole) is a problem usually hard to solve. First of all, it requires a predictive model, in order to define both the displacement magnitude and area affected by subsidence. Such model should be validated with measurements of the actual movements sustained on the surface, in order to adjust it properly and enable influence of future behaviour in a reliable way. Two different kinds of problems might arise. On one side, it is necessary to control and measure surface movements in a very exhaustive way during a long period of time, beginning before underground works take place and finishing years after they are over. Furthermore, three factors bring in errors, some times of magnitudes higher than the displacement magnitudes measured. These include: the fact that reliable and long-term information cannot always be achieved; the precision of measuring devices; and the design of the topographical network itself. In addition, the predictive models more widely used only apply to certain excavation geometries, mainly to horizontal holes. In light of this background, the Group of Rock Engineering, of the University of Oviedo Mining Department, has developed a working methodology and a specific software tool, Subsidence 3D, to estimate ground displacements and strains. The program will allow for predictive models to be defined and also allows the treatment of data related with topographical marks and its comparative analysis with calculated results. The software has been programmed using Visual C++. Graphical outputs however are generated using AutoCAD 2000. This paper mainly refers to a practical situation, an underground coalmine, remarking the main difficulties arisen during the study of the available information and proposing how to solve them. A predictive model in subsidence 3D was established and validated. The actual behaviour of the ground was that in the model.

Jan 1, 2003

By K. G. Tshilombo

It should be possible to use an oxygen probe to follow iron removal during converting, if local equilibrium is established between iron in the matte and the iron oxides in the fayalitic slag. The oxygen activity is expected to increase strongly as the iron content of the matte decreases (and the iron activity in the matte drops) while the iron oxide activity in the slag remains constant. To test this idea, oxygen activities were measured in synthetic mattes (made up of mixtures of Cu2S, FeS and Ni3S2) when in contact with silica saturated SiO2-FeO slags, and silica and (initially) magnetite saturated SiO2-FeO-Fe3O4slags. The measurements were performed on laboratory scale at 1250°C, using an oxygen probe consisting of an MgO-stabilized zirconia electrolyte and Fe/FeO reference, and containing the sample in a silica crucible. Electrical contact to the matte was by means of a platinum wire. The measured oxygen activity was sensitive to the iron content of the matte, and insensitive to the composition of the gas atmosphere over the melt. The measured oxygen activity was generally close to that predicted by Fact Sage calculations. This indicates that such oxygen activity measurements could be useful to monitor iron removal during converting of nickel-copper-iron mattes.

Jan 1, 2007

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By J. P. Germiquet

"Rock properties have a material impact on mining processes, including drilling performance. An investigation using point loaded index (PLI) data converted to uniaxial compressive strength (UCS) has revealed that a direct relationship between grain size and UCS exists at Mogalakwena Mine. This correlation is best seen in unaltered rock, with lower correlations for altered rock types. Measurements from the new RockMa system installed on drill rigs can be used to obtain rock strength data to validate the current rock strength domains and create additional data for the next benches below. An investigation of penetration rates in different lithologies shows that rock composition plays an important role in determining drill performance. Additionally, there is an inverse relationship between rock strength and drilling penetration rate – a measure of how efficiently a hole is drilled.The domaining of grain-size-adjusted UCS at Mogalakwena Mine will allow more accurate scheduling of drill rigs through increased knowledge of rock strength in various areas. Successful rock strength domaining has the potential to be incorporated into blast indexing and predicting crushing/milling performance.IntroductionThe optimization of mining and processing through geometallurgical characterization of ore are key drivers of value realization (Deutch, 2013). Rock strength is one such property and is affected by, among other variables, composition, texture, and grain size (Ozturk, Nasuf, and Kahraman, 2014). Mogalakwena Mine is exploiting the intrusive Platreef PGE (platinum group element)-bearing orebody which forms part of the northern limb of the Bushveld Complex. This complex orebody exhibits areas of metasomatic alteration, metamorphism, and sporadic mineralization of the footwall and hangingwall (Nex et al., 2006). Understanding this variability is paramount due to the implications for rock strength and hardness, which in turn affect crushing, milling, and liberation efficiency. These variables must be known prior to blasting in order to optimize mine and plant processes using in-situ variables. This necessitates predictive modelling (Deutch, 2013). Geological and geotechnical data was sourced from the Overysel (OY) exploration database for the study. Point load testing was done for each borehole and the results converted to uniaxial compressive strength (UCS) (Akram and Bakar, 2007). The relationship of lithology, texture, and grain size with UCS revealed an inverse relationship between grain size and UCS in unaltered rock. The relationship was not present in altered rock types. A comparison of mean strength and hardness results indicated that Bond work index and UCS may be related. Drilling performance is affected by UCS (Bourgoyne et al., 1986), and this was proven using recent measurements obtained during drilling. Lastly, grain-sizeadjusted UCS values were applied to a 3D model for the OY property."

Jan 1, 2016

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

This paper describes a simple finite element (FE) modelling approach which leads to the computation of seismic energy release rate (ERR) and strain energy storage rate (ESR) which result from mining. The concept of critical strain energy is introduced as a means to help evaluate the strainburst potential in mine structures. A new, energy-based, burst potential index (BPI) is proposed. The use of ERR, ESR and BPI is demonstrated by a cut-and-fill stope case study. The merits of using such energy parameters in the interpretation and analysis of strainburst phenomena are discussed. While the study gives promising results, site-specific back analyses would be required to first calibrate the model and fit it with the local mine conditions, before it can be adopted as a routine design tool.

Jan 1, 1999

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

By H. Naghavi, M. Karimi

"In self-aerated flotation machines, the gas rate depends on operational variables (e.g. froth depth and impeller speed), pulp properties (e.g. solid content and viscosity), and reagent addition (e.g. type and concentration of frother). The gas rate has a strong correlation with the flotation performance by influencing the gas dispersion properties and froth retention time. A factorial experimental design was used to study how the gas dispersion properties, the froth retention time, and the flotation performance respond to changes in froth depth and impeller speed (as the most common operational variables). An in-depth understanding of the effects of impeller speed and froth depth on the gas dispersion properties, especially the bubble surface area flux and froth retention time, is necessary to improve operating strategies for self-aerated flotation machines. All experiments were carried out in a 50 m3 selfaerated flotation cell in an iron ore processing plant. The results showed that the froth depth affected the metallurgical performance mostly via changing the froth retention time. The impeller speed had two important impacts on the metallurgical performance via varying both the froth retention time and the bubble surface area flux in the froth and pulp zones, respectively. The interaction effects of the froth depth and impeller speed were also established. This allowed us to develop a strategy for operating selfaerated flotation machines based on varying the froth depth and impeller speed with regard to the cell duty. IntroductionA mechanical flotation machine may be divided into two distinct zones. namely the pulp zone and the froth zone (Goodall and O’Connor, 1989; Yianatos, Bergh, and Cortes, 1998; Rahman, Ata, and Jameson, 2015a, 2015b). The overall flotation recovery, Ro, including the true flotation (particles attached to the bubble lamellae) and entrainment (particles recovered in water held in the bubble plateau boundaries), is a function of the recoveries in the two zones. It is calculated as follows (Dobby, 1984):"

Jul 1, 2019

By R Ratlou

Increased contamination due to sand in spiral feed has had a negative effect on the efficiency of spiral concentrators at Navigation Plant. The no. 1 seam at Kromdraai opencast, which was previously mined by underground bord and pillar methods, is now susceptible to spontaneous combustion because of air ingress into the old workings which are exposed in the opencast high wall. This posed a risk in the loss of reserves to burnt coal. As solutions, buffer blasting of the preceding cut to collapse bords and soft overburden dressing of un-collapsed bords were implemented to prevent air entering the workings. The latter remedy resulted in increased contamination due to addition of sand in Run of Mine. After evaluating alternatives, a low capital option was selected. The 110t/hr Teetered Bed Separator (TBS) has been installed, primarily to desand and upgrade the feed to the spiral concentrators. The unit indicated an upgrade with a yield increase of 0.4% during test work and is currently showing an overall plant yield increase of 0.97%.

Jan 1, 2006