Search Documents

By A. J. Dickson, A. M. Starfield

This paper reviews the progress made to date in the development of computer models of heat and moisture transfer from rock surfaces to the ventilating air in deep-level mines. The application of these programs to ventilation planning and design is discussed.

Jan 1, 2014

By B. X. Huang

Hydraulic fracturing technology is presented as a solution to improve permeability and thus solve the extraction problem of coal seam gas in low-permeability gas-bearing coal seams. Given an existing group of original cracks, the propagation of main hydraulic cracks and hydraulic wing cracks was simulated using realistic failure process analysis software. The process represents the structural transformation of hydraulic fracturing and permeability improvements caused by it. In addition, a field test for improving the permeability of gassy coal seams by hydraulic fracturing was also conducted. The propagation of the main cracks and wing cracks by hydraulic fracturing forms a network of original joint cracks, hydraulic wing cracks, and main hydraulic cracks, which improve the permeability of the coal seam. High-pressure water in the drill hole and in the main hydraulic cracks permeates the two flanks of the hole, forming the permeating water pressure. With an increase in drill water pressure and an extension of the main hydraulic cracks, the permeating water pressure on both sides of the main hydraulic cracks in the coal mass also increases. Hydraulic cracks tend to form connections through rock bridges. The extension of hydraulic wing cracks through connections in the rock bridges between the cracks transforms the rock mass to a fractured structure and improves its permeability. Hydraulic fracturing technology for improving permeability in underground conditions can increase the amount of gas drainage by a factor of 15. A stress relief area develops at a radial distance of 10-2.0 m from the hydraulic fracturing drill hole, while an area of rising stresses, called the pressurized area, develops a further 15 m away from the pressurized hole. Practice has proved the existence of the stress transfer phenomenon and the high stress area after fracturing. This kind of hydraulic fracturing technology is more effective in holes drilled from underground than in surface drill holes, with respect to costs and controllability, and is therefore the major trend in gas drainage development in coal mines.

Jan 1, 2012

By P. Gauvillé

The key driver for choosing a circulating fluidized bed (CFB) boiler is the ability to burn a wide range of fuels with highly efficient combustion while meeting low emission requirements. Reduced sorbent and water consumption compared with pulverized coal (PC) plants and the ability to deal with corrosive fuel constituents while still meeting local regulations make a CFB boiler-based power plant particularly attractive. CFB-based power generation is particularly relevant in coal mining areas. During mining, a portion of the roof and floor material may be extracted along with the coal seam in order to create adequate working height for the equipment and miners. Therefore, run-of-mine coal which comes directly from the mine contains impurities. The raw coal can undergo a washing or screening process in order to improve its quality by reducing the ash content in the fuel in order to sell it on the export market or to comply with domestic customer requirements. The coal discarded from the washing process usually has a high ash content and difficult mechanical properties resulting from the initial properties, the mining, and the coal cleaning processes. It can contain a large volume of stones or can be very fine as a result of the washing treatment. To create value from burning this discarded coal, the boiler supplier has to meet several technical challenges in developing the appropriate design. This paper highlights the performance achieved with Alstom's CFB boilers developed for power generation over the last two decades to extract value from discarded coals. Emile Huchet Power Plant is the first 125 MWe CFB unit developed for burning coal slurries (called schlamms in France). The Emile Huchet discarded coal fuel is a very fine high-ash residue with an average particle diameter by mass (d50) of around 80 µm as received from the washing plant. The paper describes the performances and the basic design of the CFB boiler to manage such a fine fuel. The performances of two other CFBs of approximately 300 MWe output in operation in the USA and PR China are also mentioned to demonstrate the capability of this technology to burn either low-volatile bituminous or anthracite waste coals. The significant issues experienced during commissioning are reported, and the conceptual choices for burning such fuels are mentioned.

Jan 1, 2012

By A. Tello

Variography was introduced by Dr. Pierre Gy to monitor a process, in the sixties. Later on, Francis Pitard extended this concept, building a complete system of variographic controls for different applications. Nevertheless, the existence of information about its use as a way to effectively control plants has been limited. There are infinite areas where variography and chronostatistics can be used. In this paper, two different cases related to gold and silver recovery, through well known but complex metallurgical routes are studied. The use of effective management of process variability software (EMPV) has shown to be a suitable solution to clarify problems at the plant and, consequently, a solution to the encountered problems has been proposed. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in depth way. Once the ore has been extracted from the mine, sampling is necessary at each sequence of the metallurgical process involved. As a first example, leaching of the ore with cyanide in agitated tanks is another case of a complex metallurgy. The aim of the process is to know about residual values in the tailings in order to optimize process. As a second example, leaching of gold and silver in ore heaps, has to be optimized in terms of time, reagents consumption and, of course, in predicting a reasonable recovery. This last issue appears to be crucial. After cyanide leaching at the heaps, a carbon in columns process is involved, where there are a series of carbon loaded columns that are submitted to a dynamic process of load and unload, to finally deliver an enriched solution to the precious metal electrowinning plant. In both cases, variography has been a good approach to show metallurgists ways to improve the operation.

Jan 1, 2009

By K. -H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes become available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60%-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none-sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as uneconomic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid. Even though smelter gas is available at high SO2 concentrations, in a conventional acid plant one would add large amounts of air to dilute the gas down to a suitable concentration of 12?13 (14) %-vol. SO2. Dealing with higher SO2 concentrations in smelter acid plants is not feasible, as the gas exit temperature of the catalytic oxidation step would exceed the allowable limit for the catalyst. Hence those conventional acid plants are characterized by the use of large equipment, i.e. high capital cost, high energy consumption and limited flexibility. The newly developed LUREC® process can handle off-gas with significantly higher gas concentrations, even in excess of 25%-vol. SO2. It is entirely based on well-proven equipment and unit operations. The first industrial application, operating with 16?18%-vol. SO2 will be presented in this paper, along with the fundamentals of the process. It will be demonstrated that the process requires inherently lower capital cost, fewer operating costs, and offers better energy recovery and lower emissions as compared to conventional design. While most existing smelter acid plants would have some built-in spare capacity, any significant increase of smelter capacity, say of 30%, can basically not be accommodated without installing an additional parallel new acid plant unit. An add-on LUREC® module can remove any such restriction, while simultaneously debottlenecking the existing acid plant. The paper also discusses the present status of the add-on technology for smelter acid plant expansions with respect to technical boundary conditions of different process alternatives as well as economic and environmental aspects. Application of the LUREC® process to modern smelter acid plants operating with high SO2 gas concentration, will lead to a substantial reduction of the specific size of the gas processing equipment and equivalent savings in capital and operating cost. The LUREC® process is patented worldwide by OUTOTEC.

Jan 1, 2009

By D. Botha, J. F. Cronjé

"SynopsisAlthough women all over the world have been involved in mining activities for centuries, mining has always been considered a very masculine industry due to its heavily male-dominated workforce as well as the physicality of mining work. The mining industry has not been an obvious career choice and preferred place of employment for women; women were mainly employed in administrative and advisory positions. Until 1994, women were legislatively prohibited from being employed in underground operations in South Africa, but the Mines Health and Safety Act, No. 29 of 1996, removed these restrictions. In addition, new mining legislation (the Mineral and Petroleum Resources Development Act, No. 28 of 2002) and the accompanying Mining Charter make specific provisions for the inclusion of women in core mining activities and require 10% of core positions to be filled by women.This article voices perceptions of the physical ability of women employed in core mining positions. Findings are drawn from empirical work undertaken at platinum, phosphate, and copper mines. Quantitative and qualitative research paradigms are used. It is evident that women find it extremely difficult to perform mine work that requires physical strength and stamina. Practical recommendations, informed by the literature review and empirical findings, are made with the objective of contributing to the sustainable deployment of women in the mining industry.IntroductionFor many years, mining has been considered the foundation of the South African economy. Although the mining industry in South Africa is currently under considerable pressure and experiences various challenges, including escalating operational costs, electricity tariff increases, safety-related issues and associated production stoppages, poor productivity, labour unrest, and reduced demand both globally and domestically, it remains a key contributor to the national economy and development of the country (IDC, 2013, p. 9).Until 1994, women were legislatively prohibited from meaningful participation in the mining industry and were denied access to skills and jobs, self-employment, and entrepreneurship. The newly elected democratic government in 1994 initiated substantial socio-political and economic transformation in South Africa. Nearly every sector in the country was transformed and re-shaped, primarily through sector-specific legislation, but also through negotiations between government, industry, and labour unions to create and refine the so-called sector charters, which included the Mining Charter. The vision of the new regime, the African National Congress (ANC), was to ‘transfer power to the people and transform society into a non-racial, non-sexist, united, democratic one, and change the manner in which wealth is shared, in order to benefit all the people’ (ANC, 2007)."

Jan 1, 2015

A project was funded by the Australian coal industry to investigate the mechanisms that might lead to sample bias when using cross-belt cutters, in order to help coal industry personnel to make better decisions about the purchase, maintenance and operation. It concentrated on DEM modelling of skew cutters. These are set at an angle to the belt with the intention of minimizing disturbance to the non-sampled material. Two bias mechanisms are likely to cause bias for cross-belt cutters. Waves of material are bulldozed off the belt by the upstream side of the body of square cutters and material is thrown by the leading edges of cutter blades for all types of cross-belt cutters. These mechanisms cause some parts of the load of material on a belt to be over-represented. The effects of these mechanisms cannot be made to be negligible, so cross-belt samplers cannot be trusted to produce unbiased samples, especially for segregated streams of material. However, it is possible to give a bound on the maximum likely bias. The grades of two portions of the stream can be estimated by stopping the belt and shovelling off 1/3 of the cross-section of the load on the belt into a container, concentrating on the final side of the belt and the top of the load. The remaining material should be put into another container and the difference in grade determined. The maximum likely bias is typically about 10% of this difference. For a cross-belt cutter, having an extraction ratio near to 100% is not a reliable indication that the cutter has little or no bias. Some bias mechanisms affecting cross-belt sample cutters make sample mass too high and some make it too low, so an extraction ratio near 100% can occur if two bias mechanisms are both active. Keywords: sampling, DEM simulation, sample bias, accuracy, precision

Jan 1, 2009

By B. Genc

Improving student success rates without compromising the quality of graduates is one of the biggest challenges expanding university programmes are facing in South Africa. By establishing a new Mine Design Laboratory (MDL) for higher learning in Mining Engineering, the School of Mining Engineering at the University of the Witwatersrand (Wits Mining) has achieved one of the important goals in its five-year strategic plan, i.e. to improve throughput in all years of study. Although the establishment of the laboratory has been a costly exercise, results so far have shown an improved success rate in most subjects taught in the facility. This paper outlines the design and equipment of the laboratory, the facilities incorporated, a comparison with the old laboratory, and the performance of students?all of which indicate how important it is to have proper facilities to improve the teaching of, and learning by, large classes. Through this initiative, Wits Mining has taken an important step that will contribute to addressing the skills shortages in the mining industry.

Jan 1, 2012

By R. Asamoah, P. Forson, S. Xu, W. Skinner, M. Zanin

In most auriferous hydrothermal deposits, gold is preferentially associated with pyrite and arsenopyrite minerals, with higher economic gold values noted for the latter and arsenian pyrite minerals. In this paper, surface (Cryo-XPS) and solution (EDTA extraction) analysis were used to characterise pyrite and arsenopyrite minerals under different aqueous conditions involving electrokinetic study and collector interactions to better understand ways of improving the separation of pyrite and arsenopyrite. The evidence showed higher surface oxidation at solution pulp pH values in the range of 4-11 for arsenopyrite relative to pyrite. The observed highest ratio of pyrite to arsenopyrite selectivity was 1.7 at collector concentration of 50 g/t and decreased with an increase in collector concentration. Keywords: EDTA extractable iron, selectivity index, differential flotation, grade engineering

Jan 1, 2020

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By P. Hand

Most coal plants must run under conditions of varying feed conditions or are asked to produce qualities different from that used in the design. This can cause overloaded conditions as the ?bottlenecks? within the plant, depending on plant operation or as the feed changes. During plant design, geological information can be used to determine washability envelopes and blends that may be expected. Historical data can also be used to develop a size distribution envelope as well as to assign reasonable models for each of the unit processes. In operation, a plant can be sampled to determine changes and to refine process models. The information obtained can then be used in an accurate simulation to define how the plant can deal with the changing environment. This paper uses Limn: The Flowsheet Processor to simulate the coal plant in detail and will produce an accurate model, in terms of equipment sizing as well as water, medium, and solids balance, for each change in feed condition. It will show examples of running the simulation through complete density and size ranges and will determine the equipment required to address each part of the performance envelope.

Jan 1, 2010

By T. T. Chiweshe, L. S. Mokhahlane, M. Welman-Purchase

This study examined an alternative technique of extracting tungsten from wolframite ore using a fusion method with ammonium phosphate salt. Current techniques use alkali salts to decompose tungsten ores and use various purification methods to produce ammonium paratungstate, which is a key intermediate precursor in the extraction of tungsten. In this study, a two-step extraction process, which involves thermal decomposition of the ore using fusion and a separation stage, is examined. The novelty of this technique is the ability to completely decompose wolframite ore and form an unstable tungsten oxide phosphate (WO2(PO3)2) compound. The instability of WO2(PO3)2 in deionized water enables selective isolation of tungsten as insoluble precipitates of WO3 and WO2. The decomposition reaction of WO2(PO3)2 is influenced by the presence of oxygen and determined to be first order under ambient conditions. Scanning electron micrographs and X-ray diffraction analysis showed above 80% of the tungsten precipitated compared with the amount that remained in the filtrate solution.

Jul 10, 2024

By Xiaoxu Sun, Jianchao Yao, Qiheng Zhu, Dubo Wang, Jiancheng He, Shijie Lu

Tower mill is considered to have a better regrinding and fine grinding effect compared with ball mill, and its application is much broader. The spiral agitator of the tower mill is driven by the motor. Media inside the mill is under the combined actions of the spiral mechanism, the cylinder, and media nearby, and these parameters are key factors affecting the grinding effect. However, it is not possible to obtain detailed information of kinematic law of media based only on traditional laboratory experiments, let alone the relationship between parameters of kinematic law of media and grinding effect. Experimentation is the only way to develop industrial equipment. However, this is time-consuming and costly, which hampers the further research of the tower mill’s grinding mechanism. The paper selects two structural parameters (gap between the edge of the spiral agitator and the cylinder wall, ratio between the diameter of cylinder and that of the spiral shaft.) and three operating parameters (diameter of media, filling ratio, the speed at the edge of the spiral agitator) as variables to do an orthogonal designed experiment of five factors, four levels, and thereby obtaining change law of grinding indicators of different parameters. Experimental equipment may be simplified to enable an applicable simulation strategy. Simulation based on a discrete element method is conducted to obtain the change law of the speed of media, collision frequency, normal force, and radial force. The relational curve between parameters of kinematic law of media and energy consumption of grinding is clarified, and key factors affecting grinding efficiency are determined. Those factors will be used for optimising the design and operating process. The research result of this paper obtained from laboratory experiments and computer simulation provides data support and theoretical bases, and has directive meaning and applicable value for tower mill’s optimisation and large-sized design. Keywords: Tower mill, discrete element method, kinematic law of media, energy consumption of grinding

Jan 1, 2020

By S. Schutte, J. Pelders, F. Magweregwede, S. Ngobese, W. Botha

A people-centric, systematic approach that involves different stakeholders is considered necessary to successfully address changes associated with modernizing the South African mining industry. In this paper we discuss the inclusion of various South African mining industry stakeholders, particularly the employees, in equipment design and development processes. Data was acquired through a literature review and inputs from South African mining industry stakeholders through focus group discussions, interviews, and an online survey. It was suggested that some of the areas that could be improved by the inclusion of employees in the process are design quality, ergonomics, equipment acceptance by the workforce, safety, efficiency, skills, insight into context of use, and early design iterations and identification of problems. Among the issues considered to be barriers to inclusion were lack of buy-in, lack of resources, difficulty in manufacturers accessing the mines, difficulties in involving too many people, intellectual property concerns, and unavailability of mine employees due to their key responsibilities. Identified critical factors in the equipment design and development process include iterative design, stakeholder participation throughout the process, needs analysis through consultation, and change management. A guideline was developed for worker inclusion in equipment design and development that could be used by the South African mining industry. The study identified several economic and social benefits of including stakeholders in the early stages of design and development. It is recommended that the South African mining industry considers using the developed guideline.

Apr 5, 2023

By D. Marcotte, R. V. Dutaut

In most exploration or mining grade data-sets, the presence of outliers or extreme values represents a significant challenge to mineral resource estimators. The most common practice is to cap the extreme values at a predefined level. A new capping approach is presented that uses QA/QC coarse duplicate data correlation to predict the real data coefficient of variation (i.e., error-free CV). The cap grade is determined such that the capped data has a CV equal to the predicted CV. The robustness of the approach with regard to original core assay length decisions, departure from lognormality, and capping before or after compositing is assessed using simulated data-sets. Real case studies of gold and nickel deposits are used to compare the proposed approach to the methods most widely used in industry. The new approach is simple and objective. It provides a cap grade that is determined automatically, based on predicted CV, and takes into account the quality of the assay procedure as determined by coarse duplicates correlation.

May 1, 2021

By G. Coetzer

"Prior to operating a non-recovery coke pilot plant, it was critical to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. Various compaction parameters were verified and established on a small laboratory-scale compaction machine to obtain a coal cake of acceptable stability. These parameters include cake density, cake surface moisture, transverse strength (force applied perpendicular to the original compacted coal cake layers), and applied force to the coal cake. This work determined the behavioural characteristics of the coal while being compacted either with a full-sized or a 1/3-sized compaction plate in a 9 kg capacity mould. Two different coals were evaluated, namely Waterberg semi-soft coking coal (sscc) and Oaky North hard coking coal.The target wet cake density of 1 100 kg/m3 (79% of 1 400 kg/m3 relative density) was achieved for Waterberg sscc, with a particle size d50 varying between 0.6 mm and 1 mm, utilizing the 1/3-sized compaction plate in the laboratory-scale set-up, with 11.6% surface moisture and 92.2 t/m2 commercial equivalent applied force. For Oaky North hard coking coal, a wet cake density of 1 189 kg/m3 (85% of 1 400 kg/m3 relative density) was achieved at a surface moisture content of 12.3% and at a lower applied force than that for Waterberg sscc, i.e. 78.5 t/m2.Coal cakes of acceptable strength, and therefore sufficient stability for further processing, were obtained for all materials evaluated during this study.Further studies should be conducted to determine the effect of zeta potential during the compaction of coals.IntroductionExxaro Resources has successfully installed and commissioned a world-class stamp-charging horizontal 1 t electrically-heated pilot-scale coke oven at its Metallurgy Services facility. Prior to operating the coke non-recovery pilot plant, it is essential to ascertain coal cake stability during the loading of a 1 m3 coal cake into the oven. The design of Exxaro’s pilot plant is such that the coal cake is pushed inside the oven by means of a pusher plate, rather than through a ‘spoon’ feed mechanism, such as is found in industrial horizontal coke ovens. The pusher plate loading mechanism dictates that the coal cake should possess high stability and inherent strength during loading into the oven, owing to frictional forces exerted by the oven floor. In order to obtain a coal cake of acceptable stability, various compaction parameters needed to be verified and established on a small laboratory-scale compaction machine."

Apr 1, 2019

By I. V. Filippova, Y. Foucaud, M. Badawi, O. Barrès, L. O. Filippov, S. Lebègue

Sodium silicate (Na2SiO3) is one of the most common reagents used in the froth flotation process, in which it is an efficient dispersant as well as a powerful gangue minerals depressant. Due to its high affinity with a lot of minerals, mostly silicates, it adsorbs on their surfaces and prevents the adsorption of the collectors, maintaining them hydrophilic. Hence, Na2SiO3 is widely used in the flotation separation of rare earth minerals, zinc minerals, iron minerals, scheelite, fluorite, apatite, and many other minerals. For decades, authors have demonstrated higher efficiency of Na2SiO3 when it is used in combination with sodium carbonate (Na2CO3), a common pH regulator. Among many well-known depressants, this system presented the best efficiency for many ores, including the Tabuaço scheelitebearing skarn studied herein. However, the mechanisms resulting in these strong positive synergistic effects are not well understood at the moment. Hence, the response surface methodology (RSM) was applied to this ore, considered as a case study, to optimize the depressing conditions and to study deeply the flotation behavior of this system. Strong synergistic effects between the two reagents were exhibited by the RSM, mostly affecting the scheelite, fluorite, and calcium-bearing silicates recoveries. This was attributed to surface carbonation of the minerals by Na2CO3, subsequently leading to a better depression by Na2SiO3. Overall, a 1:1 ratio between the two reagents displayed the best results in terms of WO3 grade and recovery. To gain understanding in the molecular mechanisms responsible for the aforementioned synergistic effects, FTIR studies were combined with state-of-the-art molecular modelling (Ab Initio Molecular Dynamics at 300 K) on fluorite, an archetype of calcium minerals. Keywords: Synergistic effects, scheelite, depressants, FTIR, DFT calculations

Jan 1, 2020

By I. Ince, S. Kahraman

Preparation of suitable core specimens for physico-mechanical testing s not always possible, particularly for soft and clay-bearing rocks. Although several indirect test methods have been proposed to predict the properties of rocks, specimen preparation from soft rocks for some indirect tests is still difficult. For such cases, the needle penetration test has been developed. In this paper we present a study on the predictability of the physico-mechanical properties of pyroclastic rocks from the needle penetration index (NPI). The NPI, uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), density, and porosity tests were performed in the laboratory on specimens from ten different locations in Turkey. Correlations were established between the NPI values and the physico-mechanical properties. Strong correlations were observed between NPI and both UCS and BTS. General correlations were found between NPI and both density and porosity.

Sep 6, 2023

By E. Van Der Lingen

This paper provides a review on coloured gold, platinum, andpalladium intermetallic compounds, and discusses the models thatwere developed to obtain these materials. These compounds have acrystal structure of high symmetry, such as the CaF2or CsClstructures, ensuring distinct electron band structures. Variousexamples of coloured gold, platinum, and palladium intermetalliccompounds are provided. More in-depth discussion is provided on thepurple gold (AuAl2) and yellow platinum-aluminium (PtAl2)compounds with CaF2structure, as well as the purplish-pinkpalladium-indium (PdIn) compound with CsCl structure. Precious metal intermetallic compounds are used in jewellery andprovide a new dimension to design. Some of these compounds havealso found use as barrier coatings on turbine blades for jet engines,and more recently, research has been conducted into their potentialuse as catalysts, electro-catalysts, sensors, capacitors, and fordecorative coatings.

Jan 1, 2014

By R. Pretorius, N. Mautsa

In a cobalt precipitation plant, phosphoric acid is used to eliminate excess uranium from the pregnant leach solution, resulting in a cobalt hydroxide product that has little uranium contamination. However, the amount of phosphoric acid added must be monitored and controlled to avoid financial and sustainability impacts and to prevent negative impacts on the final product quality. One possible solution to this problem is the use of online residual phosphorus measurement techniques to regulate the addition. By continuously monitoring the residual phosphorus levels in the solution, the plant can adjust dosing in real time to maintain the target residual phosphorus level. As a result, the cobalt precipitation plant can improve phosphorus level control, lowering the risk of overdosing, and ensuring consistent product quality. This approach can also improve process efficiency, reduce operational costs, and have a positive environmental impact

Jan 1, 2023