Search Documents

By N. Barton

Large scale tests were conducted on quartzitic gravel and crushed sand-stone to investigate pertinent geotechnical properties for backfill support of egress shafts. Such shafts are envisaged for rapid launching of deep-based missiles. The backfill support is designed to resist shaft closure under dynamic loading, and must also drain rapidly to a lower catch chamber to allow launching. Large scale tilt shear tests were performed to measure the internal shear strength of the two backfill materials. Shaft filling and emptying tests were conducted in a 12 ft deep, 3 ft diameter model section of shaft drilled in sandstone. One half of the model was smooth bored, the other half rough-surfaced to represent drill and blast surfaces. Vertical and horizontal pressure cells indicated that stress only built-up during the first 1 to 1 ½ diameters of filling, due to the high-sidewall friction of 38° for the rough shaft and 31° for the smooth shaft. Interface sliding tests were performed to confirm these figures. Static and dynamic deformation tests were also per-formed, and indicated moduli as high as 56,000 psi, which will give excellent shaft support. Both the shaft support characteristics and the ease of emptying of gravel look particularly promising.

Jan 1, 1983

By Russell J. Gartrell

This report describes the engineering feasibility and economic advantages of using a steep angle conveyance (SAC) system in conjunction with medium and large draglines to transport spoil in a typical Western Coal Mine. The SAC system, including a receiving hopper, a steep angle conveyor and a sticker/spreader, is capable of processing overburden material at the rate of 7,000 tons/hr. The unique feature of this system is the steep angle conveyor which transports the overburden material from the pit bottom to the top of the spoil at angles to 45 degrees. Compared to other means of cross-pit conveyance considered during this study, the SAC system offers the advantage of easier operation, lower conveyance cost and greater mobility. The results of this study have shown that integration of the SAC system into both established and planned new mines would improve the overall mining operation, expand the operating capability of existing equipment and reduce mining end reclamation cost.

Jan 1, 1977

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By J. B. Gayle

Commercial flotation plants operate on a continuous basis that is not simulated closely by the batch testing methods widely used in Bureau of Mines laboratory studies of flotation, Batch methods indicate whether a particular separation is possible but provide little or no information about the rates at which such separations can be effected in continuous operation, Therefore, laboratory equipment suitable for testing on a continuous basis was assembled for an investigation of a number of the operating variables that influence the flotation of coal. The results of these tests lead to the following conclusions: 1. Flotation recoveries were markedly influenced by variations in the percent solids in the feed, However, the relation between these variables is complex and depends on the particular coal and operating conditions used. Flotation rates generally increased with increased cell concentrations.

Jan 1, 1962

By F. P. Haver

Primary lead is produced in the United States by the pyrometallurgical smelting of lead sulfide (galena, PbS) concentrates, which poses sulfur dioxide and lead air pollution control problems. The Federal Bureau of Mines has investigated an alternative hydrometallurgy procedure that does not generate gaseous sulfur oxides and diminishes the potential for the escape of lead into the atmosphere. The procedure involves leaching galena flotation concentrates with ferric chloride (FeC13) solution to obtain lead chloride (PbC12) and elemental sulfur as expressed by the following chemical reaction: PbS + 2FeC13 ? PbC12 + 2FeCl2 + S°. At 100° C, over 99 pct of the PbS in the concentrate is converted to PbCl2 in less than 15 min. The leach solution, composed of brine (NaCl) containing slightly more than the theoretical required amount of FeC13, dissolves the PbC12 as it is formed, leaving a residue of elemental sulfur plus gangue. High-purity PbC12 (>99.9 pct) crystallizes from the leach filtrate on cooling and is electrolyzed in a low-temperature, fused-salt cell to obtain corroding-grade metal (>99.94 pct Pb). Spent leach solution (FeC12) is regenerated for further use by reaction with the chlorine obtained in the electrolysis of lead chloride. Other values, such as Ag, Cu, Zn, and S°, are recovered by additional treatment of either the leach solution or leach residue.

Jan 1, 1976

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

By T. Bertke

This document assesses the environmental aspects of a preliminary design for processing kaolin clay as the domestic resource for recovery of alumina by a hydrochloric acid leach-HCl gas induced crystallization process. The report covers waste sources, control measures, and potential environmental and health effects applicable to the process technology.

Jan 1, 1980

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By Virgil A. Marple

The objective of this contract was to conduct characterization, evaluation and/or calibration studies of instrumentation used for measuring the quantity of respirable dust in mining atmospheres. Initially, this work involved the upgrading and detailed evaluation of the aerosol test chamber and the development of impactors with respirable classification characteristics. These were used as standards in the chamber for measuring the quantity of respirable dust based on either the ACGIH or BMRC respirable dust criteria. A program was then conducted to calibrate several photometers. In addition, the mass sensitivity of the GCA RAM-1 photometer to water droplets in the respirable size range was determined. Three additional studies were also made in this program. First, an experimental study was performed to ascertain the effect of crosswind, cyclone orientation and particle size on particle sampling and penetration through the 10 mm Dorr-Oliver cyclone. Second, a theoretical study was conducted to refine the theory used to predict the particle collection characteristics of impactors. Third, filter samples with known quantities of diesel and coal particles were produced and delivered to the B. of Mines for testing a Raman scattering analysis technique to discriminate diesel particles in the presence of coal dust.

Jan 1, 1984

By Vance G. Leak

Leaching of manganese from low-grade Minnesota ores was studied over the temperature range 25° to 225° C at atmospheric and elevated pressures to demonstrate that good recoveries of manganese could be achieved from unroasted ores using reagents available nearby. Various combinations of ore, pyrite, lignite derivatives, and sulfuric acid were tested on a small scale. Pyrite alone required the highest temperature to effect a good extraction, but the combination of pyrite, lignite char, and sulfuric acid solubilized 99 percent of the manganese after 30 minutes of reaction at 75° C.

Jan 1, 1971

By Wilbur I. Duvall

This report presents experimental data on crater formation in four rock types. From an analysis of these data a general theory of rock breakage by explosives is deduced. This theory accounts for most of the rock breakage and other phenomena that occur when a concentrated charge is detonated in a drill hole near a free surface. From instrumented crater tests and high-speed motion pictures of the explosions, various experimental checks on the deduced theory of rock breakage are made. The general mechanism of rock breakage by explosives as described in this report is outlined briefly below. The detonation of the explosive charge creates a high gas pressure in the charge hole, which in turn generates a compressive strain pulse in the surrounding rock. This compressive strain pulse travels outward in all directions from the charge hole. Near the charge hole the amplitude of this strain pulse is sufficient to cause crushing of the rock. However, as the strain pulse travels outward its amplitude decays rapidly until no further crushing of the rock is possible. The compressive strain pulse continues to travel outward until it is reflected by a free surface. Upon reflection the compressive strain pulse becomes a tensile strain pulse. As the strength of rock in tension is much less than in compression, the reflected tensile strain pulse is able to break the rock in tension, progressing from the free surface back toward the shot point. In other words, the rock is pulled apart, not pushed apart.

Jan 1, 1957

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By Andrew Cecala

The Bureau of Mines performed tests to compare the effectiveness of steam and of water sprays to reduce respirable dust levels at mineral processing plants. By applying 0.22 wt pct water vapor as steam to product material, a 64-pct respirable dust reduction was recorded. By applying the same amount of moisture with water sprays, only a 25-pct dust reduction was recorded. By increasing the moisture content up to0.5 pct using water sprays, the dust reduction was increased to 55 pet, which was still less than the dust reduction achieved by adding less than half that amount of water in the form of steam.

Jan 1, 1985

By Pedro Lilienfeld

The objective of this program was the development, design, fabrication, and laboratory testing of a mine-worthy continuous respirable dust monitoring system (CRDMS). The operation of the sensor unit of this system is based on the light scattering intensity of the respirable fraction of airborne dust. The CRDMS is compatible with the typical environmental rigors that characterize coal mines and, in particular, the shock, vibration, impact, moisture and dust conditions prevailing at active training machines. The sampled area must be within the breathing zone of the mining machine's operator, whose dust exposure is to be monitored by the CRDMS sensor unit. Instantaneous, as well as shift-averaged dust concentrations, are displayed and recorded for later retrieval, Alarm indications and other diagnostic information are provided. The project was completed with the delivery of three sensor/display units (SDU), one data retrieval unit (DRU), two mining-machine-compatible power supplies, and two [auxilliary] battery packs.

Jan 1, 1983

By Stephen H. E. Phillips

This report outlines the modifications that have been carried out to the original prototype rectangular shaft sinking equipment for its use in a circular shaft. The surface testing of the machine is described where seven, 24 ft. diameter shafts were excavated to an average depth of 21 ft. at rates ranging between 1 ft/hr and 1.9 ft/hr depending upon the prevailing conditions. The durability and productivity standards for the equipment were established indicating that the objectives of the project had been realized. That is, when using the machine the sinking rates could be increased by 25% and costs reduced by a corresponding amount compared with conventional drill and blast methods. In addition it was shown that the machine had been developed to a state of fitness for sustained underground use.

Jan 1, 1981

By Leonard Obert

This report describes a gage which, when used with my procedure for producing strain relief, will measure the resulting borehole deformation, From the borehole deformation the magnitude and direction of the principal stresses in a plane normal to the axis of the borehole can be calculated. The design considerations, mechanical construction, sensitivity, and stability of the gage are discussed. INTRODUCTION During the past two decades an increasing mount of consideration has been given to the problem of measuring and evaluating stress in rock around underground openings. Several investigators have made theoretical and model studies of the stress and (or) strain concentrations around simulated mine openings or in structural members, such as mine pillars or immediate roof. Other investigators have developed gages for directly or indirectly measuring stress or strain, and a number of reports present the results of measurements made with these gages. Because various methods and instruments have been developed, factors involved in this type of measurement will be briefly considered.

Jan 1, 1962

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963