Search Documents

This Bureau of Mines report is devoted to descriptions of investigations pertaining to underground mine trailing cables, their handling, splicing, and the use of couplers.

Jan 1, 1979

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

By E. Morrice

As part of its efforts to maximize process efficiency and decrease energy requirements in mineral processes, the Federal Bureau of Mines has investigated methods for beneficiating bastnäsite ores from Mountain Pass, Calif. The results of a bench-scale study on the flotation of bastnäsite ore are presented. Flotation at a pulp temperature of 40° to 45°C yielded a cleaner concentrate containing 58.7 pct RE203 at a rare-earth recovery of 67 pct. These results are comparable to those reported for the commercial beneficiation method in which the pulp is heated to boiling before flotation. An attempt was also made to recover a barite flotation concentrate from the bastnäsite rougher tailing. Concentrates containing only 70 pct barite were obtained.

Jan 1, 1982

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Ned Baker

Details are given of a Hydride Fuel System to provide 5 kg of HZ to fuel a Caterpillar 3304 engine previously modified to operate on hydrogen fuel and intended to power an underground mining vehicle. The Fuel System was installed onto the engine and the Engine/Fuel System tested under cold start conditions and a full range of engine loads and speeds. Refueling tests were also performed. The fuel system tested will support full engine power and allow delivery of at least 3/4-power on a continuous basis, from cold start conditions.

Jan 1, 1983

By John F. McCoy

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller Associates, Inc. (FMA) to develop guidelines for designing, constructing, stocking and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressurization Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

By R. L. de Beauchamp

A preliminary investigation was made of the extraction of chromium from ferrochromium by low-temperature chlorination in the 3400 to 5250 C range. The objective was to devise a method for separating chromium from iron in high-carbon ferrochromium produced from domestic chromite concentrates. The majority of iron was removed as a volatile chloride; chromium was contained in the residue as a nonvolatile chloride, which was separated from carbon and unattacked ferrochromium by dissolution. A small rotary chlorination apparatus was designed, built, and used for the chlorination tests, and samples of commercial-grade high-and low-carbon ferrochromiums were chlorinated for comparison of chlorination characteristics. Low-temperature chlorination of three types of ferrochromium resulted in the removal of 81.9 to 91.6 percent of the iron content as sublimed FeC13. Recovery of chromium in a leach solution of the reactor product varied from 82.4 to 93.1 percent.

Jan 1, 1968

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

By John C. Holtz

Information on the gaseous products from the detonation of explosives has been obtained in two ways. In the first, the atmosphere in nines is analyzed after blasting, aid in the second, the gases found after detonating an explosive in a testing apparatus are analyzed. The Bureau of Mines, in

Jan 1, 1940

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By Stephen C. Tadolini, Thomas M. Barczak

A critical safety component for all underground mining is intrinsic and standing support systems. Specifically, tabular hardrock mining exploits a wide variety of deposits that require various methodologies to safely mine the ore material. Several new support systems have been developed in recent years for hard rock applications which have been modified or applied in a variety of ground control applications. These include prestressing devices, improved cribs, and free standing supports. Various standing support and prop-type systems have been designed for hardrock applications with seismic loading conditions to accept prestressing. The prestressing, using water-filled cells, creates an active load upon installation and is considered essential to maintain support during and after the blasting of the mine faces. Heavy seismic activity is also present in these mines and the prestressing units can provide some energy absorption capability to help preserve the integrity of the support. This paper presents an overview of these innovations in support technology.

By R. A. Cattell

Continuing progress in a petroleum and natural gas research program of world-wide significance makes it difficult to pinpoint accomplishments within definite time limits, and it is helpful to look back as well as forward in attempting to introduce and summarize the petroleum work of the Bureau of Mines in the fiscal year 1953. The 1952 report2 / indicated progress in a long-range program applicable in large part to both defense and peacetime requirements. The present report indicates a continuation of that program, modified partly by new demands and interests of government and industry, and is highlighted by a number of significant contributions to the knowledge of petroleum and natural gas and their production and utilization. The intent of the program was clearly epitomized in a statement made near the end of the fiscal year at a general conference of Bureau of Mines personnel where the record was critically reviewed:

Jan 1, 1955

By W. E. Robinson

Differences in the composition or chemical structure of the organic material in samples of Uinta Basin (Utah) oil shale were studied relative to stratigraphic position within the Green River Formation. This involved a systematic study of the soluble organic material and the insoluble organic material (kerogen) present in the samples. Emphasis was placed upon the distribution of the alkanes (normal and isoprenoid compounds) in the soluble extracts and upon the aromaticity of the kerogen. Significant differences exist in the chemical composition of the organic material from various strata within the Uinta Basin, some of which were related to burial depth but most were related to source material variations, environmental differences, or other factors. The Uinta Basin samples differed significantly from Piceance Creek Basin and Green River Basin samples in the large amount of soluble extract they contained.

Jan 1, 1975

By R. P. Vinson

Assessment of workplace exposures is an important tool for helping to minimize dust-related occupational illness and diseases. Real-time particulate monitoring can effectively locate areas where dust controls are needed and determine how well they are working. An affordable, person-wearable, real-time dust monitor is needed. The SKC Inc. Dust Detective (SKCDD) fulfills those requirements (Disclaimer: Mention of any company or product does not imply endorsement by NIOSH). The SKCDD consists of a disposable sampling tube (DST) connected to a small hand-held sampling pump. The SKCDD was developed through a Cooperative Research and Development Agreement (CRADA) between the National Institute of Occupational Safety and Health (NIOSH) and SKC Inc. The relationship of dust concentrations measured by personal gravimetric samplers to those measured by the SKCDD was determined in a laboratory aerosol chamber. A comparison of the means and the relative standard deviation of triplicate measurements of each type of sampling device demonstrated the SKCDD to be a viable alternative means for measuring dust. While it provides accurate measurements for specific coal types, it requires correction factors (those correction factors still need to be calculated) for other coal types.

By A. G. Galaitsis

This report summarizes the work performed under the USBM Contract No. J0245001. The purpose of this work was to expand and improve the scope and accuracy of the method developed under USBM Contract No. J0113056 for the prediction of the number of overexposed workers in the mining industry. A significant portion of the noise data were acquired during mine visits-that took place in the-course of this contract. These data were obtained with time-resolved dosimeters which among other things store a time history of the sampled noise for an eight hour work period. The remainder of the noise data have been obtained from MSHA files and from other BoM-sponsored projects. The report reviews the prediction model, discusses the model's assumptions and approximations, describes the function of the developed software, offers typical examples on the use of the software and includes plots of the newly acquired noise data records.

Jan 1, 1986

By Rudolf E. Greuer

This report contains the practical application of a computer program for the simulation of ventilation systems under the influence of mine fires and other emergencies on five hardrock mines. The introduction describes the need for such a program, its basic features, and the range of its applicability which is mainly a function of the available ventilation data. The second chapter discusses program modifications, whose necessity or desirability was, during the application, discovered. The following five chapters, which comprise the major portion of the report, give the detailed description of the program application on the five mines. For every one of the selected mines, the ventilation system, the source of the used ventilation data and their preparation for computer simulations are outlined. Based on data for the airflow distribution solely, fumes concentrations in the mines are calculated for several assumed fire locations. Based on data for airflow and pressure distributions, ventilation disturbances caused by fires as well as the resulting fumes concentrations and temperatures are determined. The consequences for escape routes and the possible means to keep them free of fumes are discussed. To investigate the capabilities of the program, other contaminant sources and other potentially dangerous ventilation factors, like fan failures and changed surface temperatures, are simulated also. The results of the calculations have been entered into ventilation plans which makes them easier to scrutinize. All significant computer printouts have been attached.

Jan 1, 1981