Search Documents

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By W. L. Staker

Alternatives were developed to the conventional ammoniacal carbonate leaching-steam stripping procedure for recovering copper as an oxide from contaminated scrap metal. By entraining air bubbles in the leach solution, the copper dissolution rate was increased to 1.5 g/in2 of copper surface per hour, compared to 0.5 g/in2/hr produced by conventional agitation in stirred tanks. Using entrained nitrogen gas bubbles for agitation in conjunction with powdered sulfur not only resulted in rapid dissolution but also simultaneous precipitation of the copper from solution as a high-grade cuprous sulfide.

Jan 1, 1971

By R. W. Dalzell, Fred N. Kissell, J. L. Banfield, M. G. Zabetakis

Methane concentration peaks were measured by the Bureau of Mines at coal mine working faces during entry development. The statistical distribution of peaks was found to be normal or log normal depending on how well the methane was being mixed into the ventilation airstream. A normal distribution indicated good mixing, whereas a log-normal distribution indicated that mixing was poor. In addition, the "highest" peaks over selected intervals were found to fit a type I extreme-value distribution, a result similar to that obtained while mining longwall faces.

Jan 1, 1974

By Ben A. Kornhauser

The mineral industry consisted primarily of natural gas production and of urea fertilizer, which was manufactured for domestic agriculture. Copper and iron deposits were being developed. Information regarding the mineral industry of Afghanistan was sparse. The Government continued to emphasize the development of mineral resources that could benefit the economy of the U.S.S.R. and repay Soviet grants. The northern half of the country, north of the Hindu Kush mountain range and adjacent to the U.S.S.R., received considerable Soviet aid to develop mineral resources.

Jan 1, 1986

By R. F. Abernethy

The work discussed in this report was done by the Bureau of Mines to develop a method for determining trace amounts of fluorine in coal. Samples of coal mixed with calcium oxide as a fixative agent for fluorine were ashed at 600° C and the residue was fused with sodium carbonate. The melt was dissolved in phosphoric and sulfuric acids and distilled to separate the fluorine) which was determined in the distillate by a SPADNS-zirconium spectrophotometric method. Fluorine determinations of 83 commercial coals ranged from 0,001 to 0.019 percent.

Jan 1, 1967

By Lewis V. Wade

This Bureau of Mines work was performed to theoretically determine the effects of specimen radius and specimen boundary conditions on the stress state in the rock near the anchor for rock specimens used to investigate expansion anchor behavior. Finite element analyses were performed on mathematical models of varying radius and boundary conditions. A review of the results of these analyses revealed a definite convergence of all stress measures considered as the specimen radius increased. There was, however, a significant variation in all stress measures as the specimen diameter increased from 8 to 12 inches.

Jan 1, 1973

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By L. D. Gehi, A. W. Khair, M. Ahmad

"Bit wear presents problems to mining operations because it affects both productivity and economics. Most bit research deals with energy requirements and energy dissipation mechanics for ideal fragmentation during the cutting process.Mechanical cutting leads to dust generation. Past studies involving dust generation due to bit wear concluded that dust concentrations increased considerably after a 7% bit weight loss: leading researchers recommend that the bits be changed at that point.Bit wear is affected by three factors: machine operating parameters in-situ mining conditions and rock properties. Operating parameters such as the depth of cut tool material spray position and the drum's rotating velocity are very important and have a definite impact on bit wear.During the mining process the amount of rock in coal and the strength of that rock is important as abrasion and adhesion take affect. Diffusive wear or deformation becomes dominant only when the temperatures exceed critical. Temperatures rise as a function of drum velocity rock properties and the cutting tool itself.Miner bit surveyIn this study, 15 mines were surveyed, and of those six responded for nine seams. The survey reflected a wide range of information about coal production and bit consumption from continuous miner sections. Also used bits were collected to get first-hand information to analyze wear."

Nov 1, 1995

By G. A. Burrell, G. W. Jones

As a part of the work which the Bureau of Mines carried out in 1916 and 1917 pertaining to the compressibility of natural gas , it became necessary to de termine the pressure -volume relations of several of the paraffin hydrocarbons of which natural gas is composed . Results of the work on natural gas were published in Technical papers 131 (Burrell , G.A. , and Robertson , I.W. , The compressibility of natural gas to high pressure , Bureau of Mines Tech . Paper 131 , 1916 , 12 pp. ) and 158 (Burrell , G.A. , and Robertson , I.W. , Compressibility of natural gas and its constituents with analyses of natural gas from 31 cities in the United States , Bureau of Mines Tech . Paper 158 , 1917 , 12 pp . ) , and curves were given of pressure volume deviations of the gases , methane , ethane , propane , and carbon dioxide at high pressures . original experimental data on these gases , however , were not published . The In view of many inquiries which the Bureau has received with reference to the original data on the se gases , and the importance of the pressure -volume relations from which it is possible to calculate the deviation of any natural gas who se composition is known , the original data as determined by Burrell and Robertson are pre sented below .

Aug 1, 1921

By James W. Jensen, Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muff ling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the sod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

By J. C. Edwards

Fire experiments were conducted in the Safety Research Coal Mine (SRCM) at the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, with coal, diesel-fuel, electrical-cable, conveyor-belt, and metal-cutting fire sources to determine the response of fire sensors to products-of-combustion (POC). Metal oxide semiconductor (MOS) and smoke fire sensors demonstrated an earlier fire detection capability than a CO sensor. This capability was of particular significance for a conveyor-belt fire in which the optical visibility was reduced to 1.52 m with an increase in CO of less than 2 ppm at a distance of 148 m from the fire. Application of a neural-network program to the sensor responses from each type of fire source resulted in correct classifications of coal, diesel-fuel, cable, belt, and metal-cutting combustion with a mean of 96% of the test data correctly classified.

Jan 1, 2000

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

By Fred Biggs, Walter Utt, Richard Miller

Powered haulage has been, and continues to be, a major source of severe accidents and fatalities at metal/nonmetal surface mines. Between 1986 and 1997, truck drivers accounted for63% of the lost-time injuries in surface haulage. This project was undertaken to reduce the number and severity of lost-time injuries among operators of these trucks. Work involved measuring shock acceleration at a western surface mine during representative work cycles on two types of trucks and collecting data from cab floors using a triaxial accelerometer and from operator seats using a seat pad accelerometer. NIOSH researchers also used the mine’s GPS systems to locate shock events on a mine map in real time. Shock tests were also run at Caterpillar, Inc.’s, proving grounds in Green Valley, AZ, to determine the magnitude of shocks resulting from controlled rock drops onto the bed of a haulage truck.

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By G. B. Atkinson

Properties of catalysts prepared from intermetallic compound precursors were investigated by the Bureau of Mines as part of its mission to decrease U.S. dependence on foreign sources for scarce catalytic materials, such as nickel, cobalt, and chromium. Methods were developed whereby catalysts with surface areas of 30 to 40 m2/g were prepared from intermetallic compounds. Activity of these catalysts for the methanation reaction and methanol synthesis was deter-mined using a fixed-bed, single-pass, flow-through reactor. Catalysts prepared from rare-earth-nickel intermetallics had specific activity for methanation that was five times greater than that of commercial catalysts and were equal to or better than commercial catalysts with regard to sulfur tolerance. Under identical reaction conditions, catalysts prepared from thorium-copper intermetallics produced more than 10 times as much methanol as a commercial low-pressure catalyst and exhibited a high degree of catalytic stability.

Jan 1, 1982