Search Documents

By Oliver Bowles

This paper is the fourth of the current series issued by the Bureau of Mines on lime- plant problems . It is hoped that the information presented in these reports will develop sufficient interest among lime- plant operators to prompt them to discuss with the Bureau their own experiences , for it is believed by such an interchange of ideas conclusions will be reached that will be of practical benefit to the entire industry . Much valuable information has been obtained from replies to the papers already issued , but a more general response is greatly desired . It is hoped that many operators will contribute additions to the information on transportation systems now at hand by answering the questions on the final page .

Mar 1, 1923

By Robert S. Sanford

This paper deals with truck haulage methods and costs at one of the many open-cut mines that are replacing rail haulage with heavy-duty trucks. At this mine, ore is trucked to a crushing plant, centrally located within one of the open-cuts. The requirements for efficient low-cost truck haulage are: Good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers The weighted average cost of hauling a long ton of ore to the crusher and the waste to the dump was reduced from $0.1993 in 1948 to $0.1114 during the last half of 1949, his corresponds to a cost per ton mile of $0.0864.

Jan 1, 1952

By Alan H. Goode

As part of the Bureau of Mines program to broaden utilization of abundant low-quality mineral materials, the Tuscaloosa Metallurgy Research Laboratory conducted beneficiation studies on two Alabama clays. The main purpose of these studies was to develop improved plasticity and green strength in both clays and compare these improved properties with those of a typical ball clay. Whiteness of the clays was also considered. The results indicated that by adjusting the pH of the kaolin to approximately 9, a substitute for ball clay could be obtained. The investigation also showed that by a combination of attrition grinding and sodium dithionite leaching to remove iron, the underclay could be upgraded to a ball clay material.

Jan 1, 1975

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners' training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry (Morbidity and Mortality Week Report, 2001; NIOSH, 2002). Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year (NIOSH, 1999). Mine safety and health professionals have long recognized training as a critical element of an effective safety and health program. Federal regulations (30 CFR, Parts 46 and 48) require mine operators to provide initial safety and health training to all new miners, as well as a minimum of 8 hours of refresher training each year. The time and money being spent to train U.S. miners is substantial, and so there is a strong and steady demand for new and better mine training materials and methods. A growing concern among mine safety professionals regards the training of new workers. A major change in the mining workforce is anticipated within the next decade. In major segments of mining, especially coal, relatively few workers have been hired since the 1970's. Thus, as an entire cohort of miners in the current workforce nears retirement, the replacement of these employees will require an influx of new workers. New miners may be young people who lack the ability to recognize and respond to mining hazards in an appropriate manner. They may also have had different educational experiences than their older counterparts. Many safety professionals believe that these two cohorts require different approaches to training. The papers in this report should help prepare mine trainers for the changes about to occur in the workforce and acquaint them with strategies they can use to enhance the effectiveness of their training. The first three papers present basic principles for teaching adults. The five remaining papers are intended to illustrate how these principles can be applied to the development and imple¬mentation of effective training for miners. Below is an overview of these papers. 1. Kowalski and Vaught review the process and principles of adult learning. The learning model they present includes a discussion of goals, content, delivery, assessment, and remediation. Adults are viewed as active learners, experienced-based, expert in their own right in specific areas, independent, real-life centered, task-centered, problem-centered, solution-driven, skill-seeking, self-directing, and internally and externally motivated. Basic aspects of curriculum development are briefly reviewed. For further information about adult learning, see Camm and Cullen's paper. 2. Mallett and Reinke's first paper discusses issues related to training new miners who have recently or will soon be entering the mining workforce. These new generations of miners have different learning style preferences and training needs than Baby Boomers and other older miners. Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these young new workers. This paper provides information that will help mine trainers communicate across the generation gap. 3. Mallett and Reinke's second paper provide an overview of training evaluation. Trainers and decision-makers are given a framework for planning and assessing training evaluation strategies. The authors present Kirkpatrick's (2001) model of evaluation categories and discuss how to start an evaluation plan and various ways to collect data. They do not provide detailed instruction in evaluation methodologies, but give trainers a review of the things they need to consider when developing an evaluation plan. A good evaluation plan can inform revisions to a training course, assess trainee learning, and/or answer managers' questions about program effectiveness. 4. Brnich, Derick, Mallett, and Vaught discuss a technique for incorporating worker participation into fire prevention and safe equipment operation training. This technique involves development of short (5 to 7 minutes) videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner's workplace. An example of one of these training modules is presented, along with the results of an evaluation performed on its effectiveness at improving miners' understanding of what types of information they should be sure to communicate during a mine emergency. 5. Wiehagen, Conrad, Friend, and Rethi discuss on-the-job training (OJT) as a method for teaching miners safety and production skills. Much of the training is done by experienced workers. This paper describes how small investments can help improve the effectiveness of on-the-job training. Effective on-the-job training involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. This paper addresses organizational considerations supporting structured on-the-job

Jan 1, 2002

By T. H. Ueng, S. D. Thompson, Y. J. Wang

"INTRODUCTION There is considerable interest among mining companies and government agencies in finding new ways to better control the generation and dispersion of respirable coal dust. Mine face ventilation generally has been considered the most effective tool for lowering the concentrations of respirable dust. Unfortunately, only a limited amount of research has been undertaken to determine the relationships between the various face ventilation parameters and the dust dispersion patterns. If these relationships are better understood, more efficient ways of controlling dust generation and dispersion may be evident. A practical and economical way to gain more in-depth understanding of these relationships is through scale model studies. Past research (1, 2, 3) has substantiated that scale models can be successfully used in studying ventilation parameters provided that geometric, kinematic, and dynamic similitues are maintained.To better understand face ventilation and dust dispersion, a 1/5 scale model of a room and pillar mine face was constructed. This model was then used to conduct experimental investigation on two ventilation parameters. The parameters which were examined included the line brattice distance from the face and the air quantity. The values of these parameters were varied in numerous experiments so that their effects on dust dispersion could be measured.The experiments of this study were unique in two ways. First, two different substances were used to simulate the respirable coal dust. Experiments were conducted with a tracer gas (methane) serving as the dust simulation substance. They were then repeated with an actual dust (Arizona Road Dust) replacing methane as the dust simulating substance. In previous scale model studies, the dust simulation substance has been limited to a tracer gas such as methane. The validity of using a tracer gas to simulate dust is not clearly known yet. The other unique thing about these experiments was the number of points measured for methane (or dust) concentration. Twenty five points in a grid arrangement were measured during each experiment of this study. The number of points measured for concentration in other studies has generally been very small (often 2 to 4). It is difficult to obtain an accurate assessment of how the ventilation parameters are effecting dust dispersion when only 2 to 4 points are measured."

Mar 1, 1989

By W. J. Fene

It is often desired to obtain samples of air in places where collection by ordinary methods is not feasible, as in shafts amore means of descent or ascent are not provided, in sewer manholes, in gas or water wells, in empty oil tanks, and in sealed areas in mines. Heretofore, when such sampling was required, it was necessary to utilize the aspirating method, which was not always satisfactory; and to obtain samples of air in deep shafts, it was necessary to use long sections of rubber tubing, which was not always available. DESCRIPTION OF NEW DEVICE A new method or "device" employs a common snap-type mousetrap to break the neck of a vacuum tube at the place where it is desired to collect the sample (see fig. 1). A mousetrap is mounted on one end of a block of wood 11-3/4 by 3 by 3/4 inches in such camper that a lead weight attached to the trigger hall spring the trap when the device is given a sharp jerk. A vacuum tube is placed on the other end of the block and held in place by a strong rubber band. A strip of corrugated rubber is placed on each side of the grooved block to prevent the tube from clipping when the sample is taken. An adjustable shoulder, provided with a rubber cap, is pieced se that the neck of the vacuum tube will rest on it. The shoulder is made adjustable to accommodate various sizes of tubas and to keep the neck of the tube from breaking tee far back from the point. A metal handle is fastened to one end of the block, with a hole in the end through which the brass wire used for lowering the device is tied. The device is enclosed by a strong wire-gauge covering, hinged on one side and so arranged that it can be locked shut on the other side. This covering prevent: breaking of the tube while it is being lowered or raised in a shaft or other place. Brass wire of not less than 22 gage should be used for lowering the device. A detailed drawing of the device is shown in figure 2.

Jan 1, 1940

By John L. Ellenberger

The Bureau of Mines investigated the occurrence of slickensides in mine roof in the Pittsburgh coalbed in a portion of the Valley Camp No.3 mine in southwestern Pennsylvania to improve the potential for prediction of slicken-sided zones and determine the orientations of the most prominent slickensided planes. Two distinct types of slickensides were identified; those which were associated with clay veins observed in the coalbed (genetic), and those which were unrelated to any visible structure (nongenetic). The study draws three conclusions: (1) Nongenetic slickensides are not the result of tectonic forces, (2) both genetic and nongenetic slickensides tend to dip at an angle of 30°, and (3) genetic slickensides tend to be alined parallel to the trend of the clay vein and usually dip toward the center of the clay vein. A schematic roof bolting plan is presented that may provide improved roof support where slickensides are present. Roof stability could be improved by supplemental bolting in the direction normal to the plane of slickensides.

Jan 1, 1979

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By R. W. Crocker, H. H. Clark

The purpose of the investigation discussed in this bulletin, one of a series dealing with the use of electricity in mines, was to study the various means and methods used to confine the flashes that occur when a switch carrying electric current is opened. The flash result- ing from the opening of a 250-volt direct-current circuit carrying more than half an ampere will ignite explosive mixtures of mine gas and air. An equally dangerous flash may be produced by even less cur- rent from a 500-volt circuit. Few mine electric circuits carry less than half an ampere when in use. The need of protecting the switches of such circuits in places where gas is likely to be present is therefore obvious. Two general methods have been proposed for preventing switching flashes from igniting gas surrounding the switch. One method is to inclose the switch in a casing provided with openings that are covered with wire gauze or otherwise designed and equipped for preventing the passage of flames from the interior to the exterior of the switch casing. Switches so protected are called explosion-proof switches. The second method is to immerse the switch contacts in oil to a depth sufficient to quench any flash that may occur when the switch is operated. Switches so protected are called oil switches. The success of the first method of protection depends upon the proper design and construction of the switch casing. It is essential to the successful operation of the second method that the switch contacts be surrounded by the proper kind of oil in good condition. There are several ways in which an oil switch may be deprived of its protective feature. The oil tank may not be filled or, if filled, the oil may leak out or be spilled. The oil tank may be removed (in some designs) and not replaced or through neglect the condition of the oil may become such that it is no longer an efficient protection. While such contingencies are not likely to occur, and although oil switches may be so designed that the loss of oil is not probable, nevertheless, as compared with oil switches, explosion-proof switches seem to

Jan 1, 1913

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920

By F. W. Wood

Ingots of zirconium and other highly reactive metals such as titanium and hafnium produced by the consumable-electrode arc-melting process require conditioning before forging or rolling. A nondestructive, arc-conditioning technique has been developed as a substitute for lathe conditioning. The technique employs en electric arc under an inert atmosphere to fuse surface metal on the sidewalls of ingots without seriously affecting the general quality of the ingots. Advantages of the practice are Increased yields, lower accumulation of inferior scrap, and actual cost savings. The work cited in this report was done on zirconium. INTRODUCTION The consumable-electrode arc-melting process as practiced at the Bureau of Mines3 4/ has proved to be a technique for producing sound, homogeneous, commercial-size ingots of zirconium and its alloys. Ingots produced by this process, however, have as a characteristic a layer of partly fused metal on the sidewall to a depth of 3/16 to 3/8 inch. To prevent extension of surface imperfections during forging, the ingots are ordinarily conditioned by removing defective material in a lathe. If the metal were less reactive or the requirements less severe, the machine chips could be recycled and remelted. However, zirconium, being so oxygen sensitive, is contaminated by merely being machined despite extensive cooling of the tool bit. Further, being contaminated with oxygen, the chip metal upon remelting is 10 to 25 Brinell-hardnese numbers harder than the ingot from which it was machined. For this reason, the ingot specifications for naval reactor use have prohibited remelting machine chips, except as required for starting pads. Again, were zirconium less costly or less in demand this ever-increasing pile could be burned to oxide and recycled through the Kroll sponge process. Economics do not favor this, as melting feed stock has an estimated increase In value over oxide of about $8.80 per pound of contained zirconium. The efforts of the Bureau to solve the problem have been directed along two lines: To reduce the contamination of the machine chips produced and to reduce the quantity of the chips produced. This paper presents the technique developed to reduce the quantity of chips produced by arc-conditioning the remelted ingot.

Jan 1, 1955

By Walter W. Fisher

A kinetic investigation of copper cementation in a revolving drum was undertaken by the Bureau of Mines to explore the effects of a porous copper deposit attached to the iron surface and a fluidized slurry of copper particles surrounding the iron precipitant. The rate of cementation was found to be significantly enhanced by the increased cathodic areas provided by a porous copper deposit or the presence of a fluidized bed of copper particles contacting the iron precipitant. The cementation rate was found to be retarded by increased ionic strength, low pH, and the presence of oxygen. The cementation reaction was first order with respect to precipitant surface area. Copper cementation on iron is visualized to occur by two basic mechanisms. Precipitation may occur through a series of shorted electrochemical cells, whereby cupric ion precipitates on a growing cathodic copper deposit, or, deposition may occur via a fluidized cathode of copper particles contacting the ion precipitant.

Jan 1, 1976

By J. Nielen van der Merwe

The move toward partial pillar extraction versus full pillar extraction has necessitated a new approach to underground section stability. When pillars are mined too small to support the weight of the overburden, they will, in some cases, remain stable for a considerable period; in other cases, they will collapse unexpectedly and violently. There is no discernable difference between the pillar safety factors of the failed and stable cases. The explanation lies in the characteristics of the overburden layers. A method is proposed that recognizes the overburden characteristics in the evaluation of stability. Two stability factors are calculated: one for the pillars, the other for the overburden. Using this method, it is possible to make use of the bridging capabilities of overburden layers to prevent pillar collapse. It is possible to scientifically design partial pillar extraction layouts that will be safe. Using energy considerations, it is also possible to prevent violent failure of pillars.

Jan 5, 1999

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 mls (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

By Todd M. Ruff

A training software package for new mine employees, called Miner Training Simulator (MTS), has been developed by researchers at the National Institute for Occupational Safety and Health. MTS is a computer-based tool that allows a trainee to enter a simulated mine and interact with his/her surroundings in order to learn basic mining concepts, safety procedures, mine layouts, and escape routes. The training simulator software and instructions for its use are described in this report. Also, each mine using the software will have different requirements with regard to safety training. To customize the simulator for these differences, an interpreted scripting language is used to define interactions between the trainee and the virtual mine and objects in it. The scripting language, called Tool Command Language, uses simple commands to control various actions in the simulation, such as sounds, safety messages, hazards, and movement of objects. The basics of the scripting language are described here, along with many examples and instructions for building a script for MTS.

Jan 6, 2001

Improve the safety of roof bolting machine operators working in underground coal mines while maintaining or improving efficiency of the roof bolting operation. Approach The Bureau of Mines funded research under contact to develop equipment that would assure greater safety in drilling holes and installing roof bolts. The research led to the design and fabrication of a roof-boiling machine that allows its operator to per-form drilling and bolting tasks while under permanently sup-ported roof or canopy protection. How the Prototype Works The major components of the remote-control roof bolter are a flexible-shaft drill that provides continuous drilling capability without the need to Stop to add drill extensions for long holes; a roof-bolt inserter that can bend a longer-than-seam height roof bolt into the drilled hole; and a roof-bolt lifter/torquer that completes insertion of the roof bolt into the hole and torques it to the desired tension.

Jan 1, 1986

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

Reduce fire warning time and avoid activation of false alarms in underground mines. Approach A heat activated stench/tracer gas system was developed which automatically releases the gas mixture into the mine ventilation air. How It Works A canister approximately 12 inches long and 3 inches in diameter is charged with 50 grams of ethyl mercaptan or other appropriate stench gas and 500 grams of instrument detectable Freon. The canister is then pressurized to 100 psi with nitrogen. A disc is used to seal the contents of the canister. A low-temperature alloy designed to melt at a predetermined temperature is used to restrain a spring loaded plunger. Upon exposure to heat, the alloy melts and the plunger is released. The plunger ruptures the disc and the mixture of stench and tracer gas is released from the canister. Canisters are mounted in areas of a mine which are susceptible to fire such as near

Jan 1, 1983

The National Institute for Occupational Safety and Health (NIOSH) recommends that occupational exposures to respirable coal mine dust and respirable crystalline silica* be controlled by complying with the provisions presented in this document. These recommendations are designed to protect the health and provide for the safety of workers exposed to respirable coal mine dust and respirable crystalline silica for up to 10 hr/day during a 40-hr workweek over a working lifetime. The information presented in this document demonstrates that underground and surface coal miners are at risk of developing simple coal workers' pneumoconiosis (CWP), progressive massive fibrosis (PMF), silicosis, and chronic obstructive pulmonary disease (COPD). Adherence to the recommendations in this document should prevent or greatly reduce the risk of adverse health effects in workers exposed to respirable coal mine dust and respirable crystalline silica. NIOSH recommends that preventive efforts be focused primarily on reducing worker exposures. Effective health and hazard surveillance and medical screening are also useful components of a comprehensive prevention effort.

Jan 1, 1997