Search Documents

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By W. P. Diamond

It is estimated that more than 1 trillion cubic feet of methane is contained within the coals of the Mary Lee group in Jefferson, eastern Tuscaloosa, and southern Walker Counties, Ala. Most of this methane will be encountered by mining. Coals of the Mary Lee group are presently being mined at depths exceeding 1,000 feet and will in the near future be mined at even greater depths, where the problem of methane gas affecting the mining operations will be acute. It is calculated that approximately 90 pct of the methane is at depths greater than 1,000 feet, and over half of the gas is contained within only 12 pct of the study area which is under more than 1,500 feet of over-burden. Degasification in advance of mining will increase mine safety, reduce ventilation expenditures, increase productivity, provide an additional energy source, and make it possible to mine parts of deep coalbeds that probably could not otherwise be mined.

Jan 1, 1976

By C. W. Davis

Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by countries to the north and south of the United States. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays or analyses for individuals or firms unless the samples are part of the ore-testing and ore-dressing investigations of the Metallurgical Division on representative ores from mining districts and of possible benefit to the entire mineral industry through published reports. All significant results obtained in this way are made public. Any mineral sample sent to this Bureau for simple identification will be examined.

Jan 1, 1938

By H. J. Seim

An ion-exchange-instrumental analysis technique is described for analyzing impurities at 1 to 1,000 parts per million level in rare-earth metals. A cation-exchange flame photometric method is used for the alkali and alkaline earth groups of metals, and an anion-exchange procedure is used in conjunction with polarographic and X-ray fluorescence techniques for selected transition elements. The standard deviation is about 6 percent, and the average error, about 5 percent.

Jan 1, 1962

By Noel N. Moebs

The Bureau of Mines investigated severe coal mine roof support problems along a section of main entries in the Pittsburgh coalbed in southwestern Pennsylvania to identify the causative factors. The mine roof was examined in detail, and various sedimentary structures are described that contributed directly to irregular and unstable roof. Small-scale paleochannels, scours, and related slickensides were identified as the leading cause of bad roof, and isopach maps were prepared to illustrate a method whereby the presence of these structures could be inferred in advance of mining. Probably second in importance was the occurrence of relatively incompetent flaggy, poorly cemented sandstone, weakened by coal and micaceous laminea. No effect of in situ stresses on roof stability was detected.

Jan 1, 1977

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

By Mark I. Copeland

The Bureau of Mines discovered that silicon and nickel additions can prevent the formation of copper alloys of Sn, Sb, and As on the surface of steel during reheating to hot-working temperatures. When molten, these copper alloys cause surface hot shortness during hot working. Wrought steels were reheated isothermally and by simulated industrial practice; the resulting surfaces were metallographically evaluated. The steels contained, In weight-percent, 0.20 C, 0.45 Mn, and up to 1.00 Si, 1.00 Cu, and 0.15 Ni, and up to 0.30 Sn, Sb, or As. The larger the Cu, Sn, Sb and As content of the steels, the greater the amount of silicon necessary to prevent copper alloy formation. A content of 0.10 Ni considerably decreased the amount of silicon necessary for copper steels containing tin and antimony, but not for those containing arsenic. Theories for the beneficial effect of silicon and nickel additions are presented.

Jan 1, 1975

By E. J. Gleim

During the past 10 years the Bureau of Mines has had a broad experience in the tasting and inspection of electric motors for gaol-cutting machines, cowl drills, storage-battery locomotives and other equipment Which is used in mines where explosive mixtures of methane and air may be encountered. From this experience the Bureau's engineers have reached the conclusion that the most satisfactory method of protecting a motor so as to prevent any sparks resulting from rough commutator, loose contacts or short-circuits in it, from igniting he surrounding atmosphere, is to totally inclose the motor with a substantial casing; having flanged joints. These joints should be metal-to-metal contact so that the shortest path from the interior to the exterior Of the casing is not less than one inch in length. On account of this experience with mining machinery, the Bureau has been asked whether an equal or loss degree of protection would be sufficient for motors for service in or about places such as refineries, gasoline filling stations, cleaning establishments and pumping stations, or in any place where there is liklihood of explosive mixtures of gasoline or naphtha vapors and air accumulating.

Jan 1, 1922

By J. H. Jansky, P. W. Jeran, G. L. Hassett, M. C. Irani

This Bureau of Mines report tabulates methane emissions from U.S. bituminous coal mines with daily emission rates of at least 100,000 cfd according to States, counties, and coalbeds. Most of the methane emitted is from mines in the Appalachian States. Total daily emissionin 1975 was 216.3 MMcfd, compared with 227.0 MMcfd in 1971 and 214.5 MMcfd in 1973. Thirty counties in nine States had daily methane emissions of 1 MMcfd or more, These emitted 93 percent of the total methane. The highest emissions were from Monongalia County, W. Va,, which accounted for 18.9 percent of the total. This was followed by Marion County, W. Va., 9.6 percent; Buchanan County, Va., 8.5 percent; Jefferson County, Ala., 6.1 percent; and Washington County, Pa., 5.9 percent. The Pittsburgh coalbed emitted 45.7 percent of the total methane, followed by the Pocahontas No. 3 coalbed with 12.9 percent. The report lists 196 mines, of which 60 had daily methane emissions of 1 MMcfd or more. Included in this compilation are the identification and thickness of the coalbed, methane emission, coal production and ventilation rates, number of drifts, shafts, and slopes used for ventilation purposes, shaft depth, age of mine, and gas-to-coal ratio.

Jan 1, 1975

By Ted C. Briggs

Equations for the elastic pressure distortion of the volumes of a Burnett compressibility apparatus are developed and presented in this report for volumes under internal and external applied pressures. An experimental method for the determination of the external pressure distortion coefficients is presented. Young?s modulus and the internal-pressure distortion coefficients are computed from the experimentally determined external-pressure distortion coefficients. The temperature dependence of the pressure distortion coefficients and of Young's modulus is evaluated for the temperature range 0° to 80° C.

Jan 1, 1968

By Raymond B. Ladoo

Talc mining ·in the state of New York was first started about 1876, but important production did not start until 1880, when about 4,000 tons were shipped, In 1883 the production was about 6,000 tons valued at $75,000, or an average of $12.50 per ton, From this date the production gradually inc~eased to a peak of 93,236 tons in 1916, valued at $961,510 or about $10,30 per ton, In 1918 the production declined to 71,167 tons valued at $902,100, or about $12,70 per ton. For ma.ey years New York ,-Jas the largest producer in the United states, but in 1917 and 1918 its output was surpassed by Vennont in tonnage thou[;h not in value. In June, 1920, there were three companies producing talc in the Gouverneur district, st. La,1Tence Co'Ul'lty, and one near Natural Bridge.

Oct 1, 1920

By B. R. Mohal, F. F. Aplan, S. Chander

"The wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3 ( CH2 ) 8-C6H4-( OC2H4 )""' where n is the number of ethoxy groups). The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3 ) 2-C6H4-( OC2H4)"").Initial wetting rates - modified Walker techniqueWalker et al. [ 6] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7] to determine the effect of surfactants on wettability of cotton fibers."

Jan 1, 1989

By Raja V. Rarnani, Robert L. Frantz

"The Generic Mineral Technology Center for Respirable Dust (GTCRD) was created at The Pennsylvania State University and West Virginia University by a congressional initiative in 1983 responding to recommendations in the 1980 National Academy of Sciences study on the Measurement and Control of Dust in Mines. Many of these recommendations dealt with the need to initiate focused fundamental research for further professional progress in dust control. Long-term, sustained support was emphasized to develop expertise in respirable dust research. In creating this Center, Penn State and West Virginia University were specifically recognized for their expertise in and facilities for research on coal mining and medicine. Today, the Center includes the Massachusetts Institute of Technology, the University of Minnesota, and the Michigan Technology University. The Respirable Dust Center is the only organization that coordinates and integrates the medical, scientific, and engineering aspects of respirable dust disease. The Center works with the U.S. Bureau of Mines (USBM), Mine Safety and Health Administration (MSHA), the National Institute for Occupational Safety and Health (NIOSH), the United Mine Workers of America (UMWA), and the U.S. coal industry in defining the research priorities for the programs of the Center to enhance research synergism.The Center's mission is to enhance the health, safety and productivity of miners by advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs to reduce the incidence and severity of respirable dust disease.All Dust Center activities are focused to be responsive to this mission, which is shared by the several federal agencies closely associated with the GTCRD. While significant progress has made mine atmospheres cleaner and healthier, respirable dust-related disease remains the nation's most pernicious industrial hazard.The goals of the GTCRD were formulated with recognition of the diverse scientific, engineering, and medical aspects of respirable dust, in addition to a need to enhance researcher interaction, as well as education and technology transfer efforts, in the respirable dust area. These goals reflect the needs of the mining industry as determined by the National Academy of Sciences Committee on Measurement and Control of Respirable Dust study done in 1980. The report of this committee encouraged the Bureau of Mines to redirect its research efforts ""...toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust."" The GTCRD's goals, detailed in chapter three of this document, were formulated to mesh with NAS recommendations."

Jan 1, 1995

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c',ov~-lo.pe;t by tL1e '.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.'l. :.-,,- #?,n c-noot'fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(' the c8n:xcity oi' the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn'rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o'q7r ir.:,l soon t ire:. the oyernt or]

Jan 1, 1938

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c',ov~-lo.pe;t by tL1e '.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.'l. :.-,,- #?,n c-noot'fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(' the c8n:xcity oi' the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn'rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o'q7r ir.:,l soon t ire:. the oyernt or, ]

Jan 1, 1938

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947