Search Documents

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By K. K. Kelley, L. B. Pankratz, W. W. Weller

Mullite is a substance of prime importance in ceramic technology . Despite this fact , its thermodynamic properties have received little attention . A Bureau of Mines literature survey disclosed the absence of lowtemperature heat capacity data , the absence of an experimental entropy value for 298.15 ° K , and the lack of heat content data beyond the temperature range from 298° to 576 ° K. Data supplied in this Bureau report fill these gaps in the thermodynamic knowledge of mullite . According to equilibrium phase studies of Aramaki and Roy ,3 the mullite phase melts congruently at 2,123 ± 15 ° K , and the equilibrium crystallinephase composition extends from Al Si2013 to Al6.8 Si₂ Q4.2 . The results in this report are for the stoichiometric composition , Al Si¿Qз . • Heat capacity measurements were made over the temperature range from 50 ° to 298 ° K , and the entropy at 298.15 ° K was evaluated . Heat content measurements covered the temperature range from 298 ° to 1,800 ° K. Heat content

Jan 1, 1963

By Foster Fraas

A separator for minerals of low magnetic susceptibility and fine particle size in a water suspension is described. A ring-shaped matrix of ferromagnetic fragments rotating so as to pass successively through magnetic-field and field-free regions provides for the separation. Application is illustrated in the separation of hematite and ilmenite from quartz.

Jan 1, 1966

By James S. Browning

The Bureau of Mines conducted laboratory batch and pilot plant flotation tests to determine the technical feasibility of recovering commercial-grade mica from a California micaceous schist. Best results in the laboratory batch tests were obtained using sodium carbonate and sodium silicate for pH control and quartz depression, and a combination of fatty acid and cationic reagents as the mica collector. In continuous pilot plant flotation tests, an alkaline fatty acid-cationic method recovered about 70 percent of the mica in a concentrate analyzing 95.6 percent mica.

Jan 1, 1965

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By E. G. King

Existing thermodynamic data for compounds of the rare-earth metals are few in number and often inaccurate because, in the past, it was difficult to obtain samples that were pure enough and reasonable in cost--a situation that is rapidly improving. This paper reports the results of low-temperature heat-capacity and high-temperature heat-content measurements for cerous fluoride (CeF3) and supplies the first such published data for a rare-earth fluoride. The low-temperature heat-capacity data cover the temperature range 51°-298° K. and serve to evaluate the entropy at 298.15° K. The high-temperature heat-content data cover the temperature range 298°-1,799° K., including the temperature and heat of fusion. The results are assembled for ready use in thermodynamic calculations. Cerous fluoride is one of the important intermediate compounds in the production of cerium metal.

Jan 1, 1959

By K. K. Kelley, L. B. Pankratz

The heat contents of four silicate minerals -- akermanite , cordierite , gehlenite , and merwinite --were measured from 298 ° to around 1,700 ° K by the dropping method . The results were compiled into tabular and equation forms suitable for thermodynamic calculations . The heat contents of these compounds are nearly additive with respect to their constituent oxides .

Jan 1, 1964

By T. T. Read

"Education is the one thing which is unanimously regarded as valuable. The growing complexity of modern life, with its intricate organization, the manifold kinds of mechanical equipment that are used, and the constantly growing, necessity for the speedy and accurate interchange of information and ideas, make education an asset that constantly increases in value. The number of things that may profitably be known has grown so large that the field of education has been divided, and attention is often directed to only those things that are most immediately valuable. Modern educational facilities are often directed to what may be called corrective, work; the, providing of people with information that they teed in the conduct of their daily lives, but which for various reasons they have not previously had facilities for acquiring. The value of special education in the industrial world has been so thoroughly demonstrated that far-seeing managers of mining enterprises are always interested in the educational facilities existing in the community where their work is carried on.The educational facilities of a modern community may be classified in several ways. They may be divided into;1. Facilities for general education, for the purpose of increasing the whole field of knowledge of the student.2. Facilities for special education, which are intended to remedy a specific defect, or to give proficiency in some special field. This may be divided as follows;a. Training for work, intended to fit an employee to adequately perform the task assigned to him, this ranges from brief instruction by a foreman or fellow-worker up to definite training courses in which the employee dose nothing but study for a period of several weeks or months, being paid during this period a wage that may range from a nominal amount up to practically full time salary. The student's educational preparation may already be fairly advanced. Some of the manufacturers of electric machinery maintain, a school similar to that just described for graduates of engineering colleges. In other cases the only pre-requisite may be a common school education, as in the schools for operators, maintained by the telephone companies."

Apr 1, 1920

In connection with tin strategic minerals investigations of the Bureau of Mines and the Geological Survey under authority of the Strategic Materials Act (Public 117, 76th Cong., 1st sess.) a study is being made of tin deposits in the United States in an effort to improve the situation with respect to domestic supplies. These studies include sampling and exploration of some of the larger deposits with the objective of establishing emergency reserves, if possible to do so. Two exploration projects have been completed, and the over-all results obtained are set forth in this progress report. RESOURCES Tin was first discovered on this continent in 100 in the Temescal Mountains of what is now southern California. In the ensuing century, occurrences of tin have been reported in no less than 17 States and Alaska. Although most of these are of scientific interest only, tin-bearing veins and placers in California, Alabama, North and South Carolina, Virginia, South Dakota, Wyoming, Texas, New Mexico, and Alaska have been extensively explored, and largo sums of money have been expended in recurring attempts to exploit them.

Jan 1, 1941

By E. J. Matson

The Little Castle Creek chromite deposit was examined in February and May 1941, respectively, by W. O. Vandenburg and O. H. Metzger, engineers of the Bureau of Mines. The Federal Geological Survey started a magnetometer survey of the area in November 1940 and completed its work during April and May 1941. Field work by the Bureau of Mines was conducted during May and June 1941. The purpose of the Bureau of Mines investigation was to search for a continuation of the chromite mineralization. The property at one time was the largest chromite producer in California.

Jan 1, 1949

By L. D. Tracy

"This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.IntroductionThe present report covers conditions and mining royalties in District VIII of the coal fields of Illinois, as designated by the Illinois Geological Survey. The various districts have been described in the reports on the Illinois coal-mining investigations, carried on cooperatively by the Illinois Geological Survey, the engineering experiment station of the University of Illinois, and the U. S. Bureau of Mines. This district includes Vermilion and Edgar Counties, but as the coal-mining operations in Edgar County amounted to only 827 tons in 1923, the data here given have been confined to Vermilion County.A similar report on District VI (Williamson and Franklin Counties) has been issued as Serial 2722 of the Bureau of Minos.A description of geological and mining conditions, and a discussion of market and transportation facilities, have been included because these have an important bearing on the royalties specified and the general conditions of the lease.Mining ConditionsDistrict VIII is better known as the Danville district and in 1923 produced 4,177,000 tons of coal, or approximately L per cent of the total output for the entire State for that year, which was 79,300,000 tons."

Apr 1, 1926

By Edward D. Thimons

The Bureau of Mines has developed a damage-resistant brattice, intended for use as a stopping in locations where blast damage to stoppings is a problem, the roof is relatively flat, and the differential pressure across the stopping is not high. Damage-resistant brattices consist of a series of vertically hung brattice panels joined to each other by Velcro connections that improve the airtightness of the brattice. When the brattice is subjected to strong blast forces, the Velcro connections peel apart, allowing the panels to open without incurring damage. The Velcro connections can then be resealed in a matter of minutes. A preliminary test in the Bureau's Safety Research Mine and subsequent long-term testing at the White Pine copper mine in Michigan and the Retsof salt mine in New York show that damage-resistant brattices withstand blasting better than conventional stoppings, while still performing as efficient air barriers when the Velcro connections are sealed.

Jan 1, 1978

INTRODUCTION The pager phones used in many underground coal mines are battery- operated, party-line telephones with provisions for loudspeaker paging. The system is two-wire, non-polarized, and is operated by self-contained batteries. Many of the individual units are certified as permissible. Requirements for installation are specified in state and federal regulations, such as in the Code of Federal Regulations, Title 30, Mineral Resources, Part 75. The major federal regulations that affect communication in coal mines are noted below, with a brief description of the subject matter in each of the relevant paragraphs. Refer to the cited paragraphs of Title 30 for explicit details of these regulations. (This brief description is for reference purposes only.) Minimum Requirements (paragraphs 75.1600, 75.17 13-2, and 75.1003-1) Approved telephone or two-way communication will be provided between the surface and each main shaft landing and each working section ; to the nearest medical assistance; and shall be protected from contact with trolley wires or trolley feeder wires. Installation Requirements (paragraphs 75.5 16-2, 75.52 1, and 77.508-1 ) Communication wires will be supported on insulated hangers, attached to messenger cables, or buried, to protect against mechanical damage ; installed opposite trolley wires; and insulated near power conductors . . . each cable will have lightning arresters within 100 feet of going below ground . . . and arresters will be provided wherever telephone wires enter a building. Wire and Cable Requirements (paragraphs 75.5 16-2, 75.5 17, and 75.52 1) Communication cable means two or more insulated conductors, covered by an additional abrasion-resistant covering; power wires and cables shall be adequately insulated and fully protected; and lightning arresters shall be connected to low-resistance grounds, more than 25 feet from neutral grounds.

Apr 1, 1975

By Perry G. Cotter

The borides of the transition metals in Groups IV and VI exhibit, in addition to a certain degree of hardness, considerable resistance to heat and oxidation. They have high melting points (1,850°-3,060° C.) and low coefftcients of thermal expansion and can be bonded with other materials and hot-pressed to desired shape (cermets). Suggested uses for the borides include use in rockets and jet engines, as thermocouple protection tubes, as containers for molten metals in die casting, as flame-plated coatings on less refractory compositions to prevent erosion by hot gases, and as control rods and neutron shielding material in nuclear engineering, The Federal Bureau of Mines investigation of zirconium diboride started in 1950 at the Boulder City Nev,, Metallurgy Research Laboratory, Its purpose was to reduce the cost of raw materials for the production of zirconium diboride.

Jan 1, 1961

By Stuart Bjorklund

This paper is one of many reporting various aspects of the Bureau of Mines program initiated in August 1939 by passage of the Strategic Minerals Act J the scope of which was greatly expanded by subsequent legislation. In its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The occurrence of chromite in the Knik Valley near Palmer, Alaska, was brought to the attention of the Bureau of Mines in September 1941 by George Johnson, of Anchorage. At that time a preliminary investigation was made by Robert S. Sanford, an engineer of the Bureau of Mines. The area was investigated on June 4 and 5, 1943, by Henry R. Joesting and Leo H. Saarela, engineers of the Territorial Department of Mines. In August 1942, a second chromite occurrence, the Highway deposit, in the Knik Valley, was reported to the Territorial Department of Mines by John E. Ryan of Anchorage.

Jan 1, 1948

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

By A. H. Warner

Sphalerite crystals occur sparingly in minor faults and pockets in a coarsely crystalline dolomite on the Brown-Tipton farm near Greenville in Greene County, Tenn. After several visits by U. S. Bureau of Mines engineers and U.S. Geological Survey geologists, a survey was r: the in the fall of 1944. Upon their recommendations, trenches on the Brown farm under Bureau of Mines supervision. In each case, the bed most favorable for zinc deposition was exposed. In the finished trench bottoms no zinc minerals are visible.

Jan 1, 1950

By L. B. Pankratz

The heat contents of the sesquioxides of erbium, holmium, thulium, and ytterbium (Er203, Ho203, Tm203, and Yb203) in the cubic crystalline form were measured over the temperature range from 298° to 1,800° K. The erbium and holmium sesquioxides gave regular heat content-temperature curves. Thulium sesquioxide had a minor thermal anomaly near 1,680° K, with a heat absorption of 310 cal/mole; similarly, ytterbium sesquioxide had a minor anomaly near 1,365° K, with a heat absorption of 150 cal/mole. The heat content results are presented in both tabular form (at 100° intervals) and in algebraic form. Entropy increments, corresponding to the tabulated heat content results, also are listed.

Jan 1, 1963

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992