Search Documents

By H. H. Schrenk, Carlton E. Brown

"INTRODUCTION The angle at which a hole is drilled has long been thought to affect the amount of dust disseminated into the air during wet drilling. The amount disseminated has been reported as increasing rapidly with the approach of the angle of the hole to the vertical (up) position. 4/ This has been explained commonly as being caused by a decrease in contact of water with the face of the drill hole; increase in amount of sludge dropping through the air; and increase in amount of sludge running down the drill steel and being thrown into the air by the rotation of the drill steel and by leakage of air from the front head of the drill.The steep up angles of the holes drilled are responsible, at least partly, for the higher dust concentrations found in such places as raises, compared with those at level faces, where most of the holes are drilled at angles farther from the vertical (up) position. The mining industry is coming to realize more and more the importance of the angle of the drill hole as a contributing cause of the high dust concentrations found in some raises. Much work is being done to counteract the effect of the angle of the drill hole on dust dissemination. The rate of rater flow through drill steels is being increased by the use of water tubes of larger diameter or by higher water pressures to obtain better contact between water and the face of the drill hole. Traps are being developed to catch the sludge from the drill hole and allow it to drain down through a special pipe before it drops through the air or runs down the drill steel. Drills that permit little or no air to leak from the front head along the drill steel are being designed and used. Care is being taken to prevent the exhaust from the drill dispersing the sludge into the air."

Feb 1, 1938

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By BUREAU OF MINES

This paper is a revision of Reports of Investigations , Serial 2541 , which was published in November , 1923 , for the benefit of State mining inspectors , safety engineers of mining companies , and others interested in electrical safety inspection in mines . It presents the important points that should be watched by inspectors and briefly reviews the work of the Bureau of Mines in testing of electrical apparatus and equipment to determine their permissibility for use in gassy coal mines .

Jan 1, 1929

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By L. B. Berger

Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the dangers of this gas, and frequent now items retort the finding of persons dead or unconscious from the effects of carbon monoxide, yet these accidents continue. Either those warnings are not read, or they are unheeded by people who feel that "It can't happen to me." It can happen to you - carbon monoxide is no respecter of persons, as evidenced by items appearing daily in newspapers all over the country. Carbon monoxide has been a threat to human safety as long as man has used fire to keep himself warm and to cook his food. The burning of any fuel that contains carbon may produce carbon monoxide. This is true of solid fuels such as coal, coke, and wood; of liquid fuels such as oil, gasoline, and kerosene, and of gaseous fuels such as natural or manufactured gas. In the process of combustion the carbon in the fuel unites the chemically with tat oxygen of the air to form carbon dioxide (CO2), however, if the supply of air is not adequate, combustion is incomplete and carbon monoxide (CO) will be formed.

Jan 1, 1943

By Peter. PH. D. Cain

Smoky River Coal Ltd. mines low-volatile metallurgical coal by surface and underground methods in the foothills of the Rocky Mountains of Alberta, Canada. Current underground operations are confined to the 5B-4 Mine. Development of 5B-4 began in January 1998; production from depillaring sections commenced in July 1998. This paper describes the history of underground mining on the Smoky River property in terms of extraction methods and pillar design. The development of the present pillar design guidelines is discussed in this context. Recent work to prepare a number of case histories for back-analysis using the Analysis of Retreat Mining Pillar Stability (ARMPS) method is described, along with the modifications developed for calculating the ARMPS stability factor for retreat extraction of thick seams. The design criteria are described, as well as the geotechnical program implemented in order to verify its applicability.

Jan 5, 1999

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By C. H. Schack, A. O. Ipsen, H. G. Poole

"INTRODUCTION In the course of the investigation of manganese mineral occurrences in continental United States, the Bureau of Mines has collected several lots of ore from properties in the vicinity of Long Valley, Ariz. The ore occurs as irregular and random pockets in a brecciated zone. As only high-grade portions of the deposits obtained by selective mining would be acceptable as commercial-grade manganese ores, an investigation was made to determine amenability of the ores to concentration by ore-dressing methods. Several types of ores, differing in grade and mineral associations, were studied.Ores from the Vaiazza property are of special interest, owing to the successful application of silica flotation for their concentration. Ores from the Shroup and Conner-Hough properties are very similar but differ somewhat in their response to ore-dressing Method's. In all instances, the man¬ganese minerals are psilomelane and pyrolusite, with minor amounts of other manganese oxides. The country rook is a brecciated limestone; the diluent in the high-grade ore pockets is chiefly silica. The low-grade manganese ores are limestone replacements, and the chief gangue material, of course, is limestone."

Nov 1, 1947

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By Arne Landsberg

Accessory metals, although valuable resources, present possible environmental concern in the smelting of base metals. The Bureau of Mines, U.S. Department of the Interior, has undertaken research to define the chemistry involving these metals. Arsenic in copper smelting is the first to be investigated. Roasting, the first step in many copper smelters, was chosen for initial investigation because of the potential for arsenic removal in this primary process. Simple, static-bed, vaporization experiments were devised to obtain the data in this study. Ancillary transpiration and mass spectrometry were also used to delineate conditions necessary for arsenic volatilization from a roaster feed. For nearly complete arsenic removal, a temperature of 650°-700° C, a reducing atmosphere including carbon monoxide, and a source of sulfur were found to be essential.

Jan 1, 1980

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963